Theoretical analysis of surface plasmon resonance based fiber optic sensor using indium nitride

An extremely sensitive surface plasmon resonance based fiber optic sensor with indium nitride (InN) layer coated on the core of the optical fiber is theoretically analyzed. The proposed sensor exhibits high sensitivity in the near infrared region of spectrum. The optimized value of thickness of InN layer is found to be 70 nm. Possessing high sensitivity of 4493 nm/RIU, the 70 nm thick InN layer based fiber optic SPR sensor illustrates good sensing behavior.     

Surface plasmon resonance based tapered fiber optic sensor with different taper profiles

A theoretical model for surface plasmon resonance (SPR) based tapered fiber optic sensor is proposed with three different taper profiles, namely, linear, parabolic, and exponential-linear. The effect of taper ratio and taper profiles on the sensor’s performance is studied in detail and the design considerations for significantly enhanced sensitivity are reported. The study shows that the exponential-linear taper profile with high taper ratio provides the best performance. The physical reasons behind sensitivity enhancement due to taper ratio and taper profile are given, wherever required.     

Fiber optic sensor based on surface plasmon resonance with nanoparticle films

This paper reports on a novel design of a fiber optic surface plasmon resonance (SPR) sensor based on nanoparticle metal film. The performance of the proposed sensor in terms of its signal-to-noise ratio (SNR) and sensitivity under different conditions related to the film with spherical gold nanoparticles embedded in a host material is theoretically analyzed. In particular, the effect of the parameters such as gold particle size, film thickness, and refractive index of host material is studied and the possible explanation, whenever required, is given. The numerical results presented in this paper leads to fulfill the requirement of significant optimization of the important design parameters to achieve a high SNR and sensitivity of a fiber optic SPR sensor with nanoparticle films.     

Numerical simulation of wavelength-modulated surface plasmon resonance-based fiber optic sensor

A systematically theoretical analysis of a surface plasmon resonance (SPR)-based optical fiber sensor is carried out. A three-layer mode (fiber core/gold/sample) is used to simulate the SPR-based optical fiber sensor. Several parameters including the thickness of gold layer, numerical aperture (NA) of fiber, sensing region length and fiber core diameter have been investigated to evaluate the sensitivity and measurement accuracy of sensor. A detailed explanation for the effect of these parameters on the sensor is presented to give a guideline to optimally design the SPR-based optical fiber sensor.     

基于氧化铟锡的十重偏芯D型光子准晶光纤的高灵敏度表面等离子体共振传感器

设计并分析了一种高灵敏度表面等离子体共振(SPR)传感器,该传感器由偏芯D型结构的十重光子准晶光纤(PQF)组成,并局部涂覆氧化铟锡(ITO).偏芯D型结构可以使液体分析更加方便,增强了纤芯模与SPP模之间的耦合,提高了传感灵敏度.采用有限元法对传感器的特性进行研究.结果表明,传感器的波长灵敏度随折射率(RIs)的增大...     

准晶体结构光纤表面等离子体共振传感器特性研究

光纤表面等离子体共振传感器在高灵敏度传感和在线实时监测等领域具有重要意义. 设计了一种六重准晶体结构环形通道光纤表面等离子体共振传感器, 基于有限元法对该传感器的传感特性进行了数值模拟. 研究了光纤各结构参量对传感器特性的影响规律. 研究结果表明: 待测液折射率的有效监测范围为1.25–1.331, 最高灵敏度可达26400 nm·RIU^-1, 传感器具有损耗谱杂峰少、探测范围广、灵敏度高、设计灵活性高和光路可弯曲等特点, 在生化检测、公共安全、环境污染监测以及高灵敏度传感等领域具有广泛的应用前景.     

Total dissolved solids estimation with a fiber optic sensor of surface plasmon resonance

In this paper, surface plasmon spectra of ion influence was investigated by using a fabricated fiber optic sensors, then spectrum subtraction of ion and non-ionic solutions were developed for field applications of total dissolved solids (TDS) estimation. We confirmed the SPR spectral difference between seven ionic and three non-ionic liquid samples, that for the same refractive index, resonance wavelength in SPR spectrum is much higher for ionic samples than that in the case of non-ionic ones due to the ions influence. The positive correlation of ion content and extra resonance wavelength shift has been established for TDS estimation in water. With three groups of water samples investigation and field testing, the proposed SPR technique showed a good performance comparable to the conductivity method.     

Surface plasmon resonance sensor based on diffraction grating with high sensitivity and high resolution

A surface plasmon resonance (SPR) sensor based on diffraction grating with high sensitivity and high resolution is proposed. The sensitivity of grating coupled SPR sensor based on angular interrogation is enhanced by replacing +1st diffraction order of metallic grating with −1st diffraction order to excite the surface plasmon. To improve the resolution of grating-based SPR sensor, aluminum is used as an SPR-active metal. The reflectivity dip of the Al-based sensor is sharper than an Au-based one, which is the mostly widely used as SPR-active metal. And 3-nm-thick gold film is deposited on the grating surface in order to protect the Al layer from getting oxidized. Numerical simulations show that the sensor not only has high sensitivity and high resolution, but also exhibits good linearity.     

基于表面等离子体共振的新型超宽带微结构光纤传感器研究

基于表面等离子体共振的微结构光纤传感器具有高灵敏、免标记和实时监控等优点.如今,由于此类传感器广泛应用于食品安全控制、环境检测、生物分子分析物检测等诸多领域而受到大量研究.然而,目前所报道的绝大多数此类传感器只能应用于可见光或近中红外传感.因此,对可应用于中红外传感的表面等离子体共振微结构光纤传感器的研究是一项极具挑战...     

Surface plasmon resonance sensors based on Ag-metalized nanolayer in microstructured optical fibers

Surface plasmon resonance sensors based on Ag-metalized nanolayer in microstructured optical fibers are theoretically analyzed by using finite element method (FEM). In our simulations we use Drude-Lorentz model to describe the metal dielectric constant. The numerical results show that the sensitivity of Ag-metalized SPR sensor could reach 1167 nm/RIU and corresponding resolution is 8.57×10⁻⁵ RIU. Compared to conventional Au-metalized SPR sensors the performance of our device is obviously better.     

Numerical study of a highly sensitive surface plasmon resonance sensor based on circular-lattice holey fiber

A new design of surface plasmon resonance (SPR) sensor employing circular-lattice holey fiber to achieve high-sensitivity detection is proposed. The sensing performance of the proposed sensor is numerically investigated and the results indicate that our proposed SPR sensor can be applied to the near-mid infrared detection. Moreover, the maximum wavelength sensitivity of our proposed sensor can reach as high as 1.76×10⁴ nm/refractive index unit (RIU) and the maximum wavelength interrogation resolution can be up to 5.68×10^-6 RIU when the refractive index (RI) of analyte lies in (1.31, 1.36). Thanks to its excellent sensing performance, our proposed SPR sensor will have great potential applications for biological analytes detection, food safety control, bio-molecules detection and so on.     

光纤SPR湿敏传感器及其共振光谱特性研究

提出并研制了基于光纤SPR传感探针的新型湿敏传感器。首先研究了光纤SPR传感探针对环境湿度变化的敏感特性,在此基础上提出在光纤SPR传感探针表面增覆不同厚度且具有水分子吸附功能的PVA薄膜来实现环境相对湿度的监测。研究结果表明,增覆双层PVA薄膜的光纤SPR传感探针在高湿区具有较好监测效果,其共振强度对应的相对湿度测量灵敏度达到1.59%/%RH,较光纤SPR探针呈现显著提高。而增覆单层PVA薄膜的光纤SPR传感探针在高湿区共振波长对应的相对湿度监测灵敏度达到2.411nm/%RH。此外所提出的新型光纤SPR湿敏探针在PVA薄膜失效后经过特殊工艺处理仍可重复镀膜使用。     

Surface plasmon resonance polarizator for biosensing and imaging

A novel polarization-sensitive surface plasmon resonance (SPR) biosensing/imaging scheme is proposed. The scheme uses a periodical spatial phase modulation of the pumping beam of a mixed polarization in the Kretschmann–Raether geometry and takes advantage of SPR-based polarizing effect to drastically absorb p-polarized component changing the resulting polarization state of the beam. The scheme then uses Fourier Transformation to efficiently treat and filter spatially-modulated polarization-sensitive signals and thus to extract and process selected SPR-based response. This approach offers a much higher accuracy of measurements in SPR-based multi-sensing and remote sensing.     

基于D型双芯PCF的近红外宽检测范围SPR折射率传感器

现有报道的PCF-SPR折射率传感器的检测范围普遍较窄,不能实现低折射率的检测,且工作波段多数集中在可见光或通信波段,这限制了传感器的应用范围.鉴于此,提出了一种基于D型双芯PCF结构的SPR传感器,使用氧化铟锡作为等离子体材料沉积在D型PCF抛光表面,并对该传感器的理论模型进行了分析,包括金属参数对传感性能的影响,P...     

基于表面等离子体共振和定向耦合的D形光子晶体光纤折射率和温度传感器

利用光子晶体光纤结构的灵活性和性能的优越性, 设计了一种基于D形光子晶体光纤的折射率和温度传感器. 在D形光子晶体光纤表面抛磨并镀上金纳米薄膜, 作为表面等离子体共振传感通道用来测量液体折射率; 在包层的一个空气孔中填充温敏液体甲苯, 作为定向耦合通道实现对温度的测量. 进一步的数值计算发现, 基于定向耦合效应的温度传感和基于表面等离子体共振的折射率传感相互独立, D形光子晶体光纤同时进行折射率和温度传感检测. 在各向异性的完美匹配层边界条件下利用全矢量有限元法对该传感器特性进行了数值研究, 发现D形光子晶体光纤的空气孔直径决定了定向耦合吸收峰的中心波长和温度传感的灵敏度, 金薄膜的厚度和D形结构的抛磨深度仅影响表面等离子体共振峰的相对强度. 结果表明: 该传感器在-10–80 ℃的温度范围内具有11.6 nm/℃的温度灵敏度, 在1.34–1.44折射率范围内折射率灵敏度最高可达26000 nm/RIU.     

基于超连续谱的光子晶体光纤表面等离子体效应

提出了利用光子晶体光纤空气孔塌缩技术制作光子晶体光纤表面等离子体共振传感器,构建了空气孔完全塌缩的光子晶体光纤表面等离子体共振传感器模型,并模拟计算了其中的表面等离子体共振效应。制作了全光纤化的波长检测型的光子晶体光纤表面等离子体共振传感器,利用超连续谱光源进行了相关实验。实验结果表明:以空气为待测环境介质时,对应的共振波长为465 nm,与理论计算相符合。     

LED based fiber optic surface plasmon resonance sensor

Modeling of a miniaturized fiber optic sensor based on surface plasmon resonance utilizing a broad band diffuse source is presented. Attenuated total internal reflection with Kretschmann configuration is the basis of the theoretical model. For simulation both meridional and skew rays are considered. The performance of the sensor is evaluated in terms of sensitivity, detection accuracy and signal to noise ratio. Effects of the numerical aperture of the fiber, core diameter and length of the sensing region on the performance parameters of the sensor are studied. The results are obtained for gold and silver metallic layer on the core of the fiber. The theoretical results obtained are compared with SPR based fiber optic sensor utilizing focused beam on the end face of the fiber from a collimated source. The advantages of using broadband LED (diffuse source) source for launching light in the fiber are the miniaturization, compactness and low cost of the sensor.     

基于超连续谱的光子晶体光纤表面等离子体效应

 提出了利用光子晶体光纤空气孔塌缩技术制作光子晶体光纤表面等离子体共振传感器,构建了空气孔完全塌缩的光子晶体光纤表面等离子体共振传感器模型,并模拟计算了其中的表面等离子体共振效应。制作了全光纤化的波长检测型的光子晶体光纤表面等离子体共振传感器,利用超连续谱光源进行了相关实验。实验结果表明:以空气为待测环境介质时,对应的共振波长为465 nm,与理论计算相符合。     

Polarization-insensitive surface plasmon resonance sensor by cross-slit metallic periodic arrays

We propose a plasmonic structure to obtain polarization-insensitive localized surface plasmon resonance (LSPR) sensor, which consists of cross-slit metallic periodic arrays embedded in the background material. Numerical simulation illustrates that the mechanism of the LSPR sensor is based on the shift of the Fabry–Perot cavity mode resonance peak in the spectrum as the change of the dielectric material properties for the near fields. And one of the transmission dips of the structure is very sensitive to the background materials; the structure could gain the sensitivity (nm/RIU) more than 500 nm/RIU. Meanwhile, the structure holds great potential to achieve high-performance sensors in practical application due to polarization-insensitive virtue.     

Microstructured fiber based plasmonic index sensor with optimized accuracy and calibration relation in large dynamic range

A novel surface plasmon resonance photonic sensor is proposed using an index-guided microstructured fiber with an analyte channel introduced into the central core. Compared with the previous designs of porous fiber core, variation of the signal amplitude with exterior refractive index is demonstrated to be contrary to that of the sensitivity in the proposed fiber, contributing to optimized detecting accuracy over a large refractive index range of 1.33 to 1.42. By carefully choosing the central channel size, the analyte-filled core can achieve narrower resonance spectral width and higher signal to noise ratio (SNR) than the air-filled core. Sensor responses are also studied in this paper based on two spectral interrogation methods, including monitoring single resonance shift and measuring change in the resonance separation. For both methods, response linearity has been improved considerably through partially filling the core with analyte. The maximal sensitivity reaches 10^− 6 refractive index unit (RIU). The linear sensing performance along with the broad measurement range is very promising in the application of the proposed sensor as sensitive refractometer.