稀土La掺杂CrSi2电子结构与光学性质的第一性原理研究

基于密度泛函理论的第一性原理赝势平面波方法, 对稀土La掺杂CrSi2的几何结构, 电子结构和光学性质进行了计算与分析. 结果表明, La掺杂后, CrSi2的晶格常数a, b 和c均增大, 晶格体积增大. La掺杂导致费米面进入价带, 带隙明显变窄仅为0.07eV; 在费米面附近, La原子的5d层电子态密度只占总态密度很小的一部分, 而总态密度仍然由Si的3p层和Cr的3d层电子的分波态密度决定; La掺杂后CrSi2的静态介电常数ε1(0)由28.98增大为91.69, ε2(ω)的两个介电峰均向低能方向偏移且增强, 光学吸收边向低能方向移动, 吸收峰减小. 计算结果为CrSi2材料掺杂改性的实验研究提供了理论依据.     

Al掺杂浓度对CrSi2电子结构及光学性质的影响

采用基于第一性原理的赝势平面波方法,对不同Al掺杂浓度CrSi2的几何结构、能带结构、态密度和光学性质进行了计算和比较。几何结构和电子结构的计算表明:Al掺杂使得CrSi2的晶格常数a和b增大,c变化不大,晶格体积增大;Cr(Si1-xAlx)2仍然是间接带隙半导体,掺杂使得费米面向价带移动,且随着掺杂量的增大而更深地嵌入价带中,费米能级附近的电子态密度主要由Cr的3d态电子贡献。光学性质计算表明,随着掺杂量的增大,Cr(Si1-xAlx)2的静态介电常数、第一介电峰、折射率n0逐渐增大,平均反射效应减弱,表明Al掺杂有效增强了CrSi2对光的吸收,能够提高其光电转换效率。计算结果为CrSi2光电材料的应用和设计提供了理论指导。     

Ac掺杂β-FeSi_2光电性质的第一性原理研究

基于密度泛函理论(DFT)框架下的第一性原理赝势平面波方法,对锕(Ac)掺杂β-FeSi2的几何结构,电子结构和光学性质进行了计算与分析。几何结构的计算表明:Ac掺杂后β-FeSi2晶格常数a、b及c都有所变化,晶胞体积增大。电子结构的计算表明:Ac掺入后导致费米面进入导带,能带结构仍为准直接带隙,但是带隙明显变窄;费米能级附近,总电子态密度主要由Fe的3d层和Si的3p层电子态密度决定,Ac的6d层电子态密度贡献很小。光学性质的计算表明:静态介电常数ε1(0)明显提高,介电函数的虚部ε2的峰值向低能方向移动并且减弱,折射率n0明显提高,消光系数k向低能方向有一微小的偏移,吸收峰增强,平均反射效应变化不大,计算结果为β-FeSi2材料掺杂改性的实验研究提供了理论依据。     

第一性原理计算V-Al共掺杂CrSi_2的光电特性

采用第一性原理赝势平面波方法,对V-Al共掺杂CrSi2的几何结构、电子结构和光学性质进行了理论计算,并与未掺杂、V、Al单掺杂CrSi2的光电性能进行了比较。结果表明:V-Al共掺杂会增大CrSi2的晶格常数a和b,体积相应增大。V-Al:CrSi2是p型间接带隙半导体,带隙宽度为0.256eV,介于V、Al单掺杂CrSi2之间;费米能级附近的电子态密度主要由Cr-3d、V-3d、Si-3p、Al-3p轨道杂化构成。与未掺杂的CrSi2相比,V-Al:CrSi2的静态介电常数和折射率增大,εi(ω)在低能区有一个新的跃迁峰。在光子能量为5eV附近,εi(ω)的跃迁峰强度大幅减弱,吸收系数和光电导率明显降低,吸收边略有红移,平均反射效应减弱。V的掺入会削弱Al单掺杂的电子跃迁,V-Al共掺杂可以对CrSi2的能带结构和光学性质进行更精细的调节。     

稀土（Y、Ce）掺杂β-FeSi2光电性质的第一性原理研究

基于第一性原理赝势平面波方法,对稀土(Y、Ce)掺杂β-FeSi2的几何结构、电子结构和光学性质进行了计算与分析。几何结构的计算表明,Y 或Ce掺杂后β-FeSi2的晶格常数改变,晶胞体积减小。电子结构的计算表明,掺入稀土后β-FeSi2 费米面附近的能带结构变得复杂,带隙变窄;总电子态密度发生了变化,Y 的4d 轨道电子态密度和Ce的4f轨道电子态密度主要贡献给费米面附近。光学性质的计算结果表明,Y 或Ce 掺杂后β-FeSi2 的静态介电常数明显提高,介电函数虚部ε2 的峰值均向低能方向移动并且减弱,折射率n0 明显提高,消光系数k 的峰值减弱,计算结果为β-FeSi2材料掺杂稀土改性的实验研究提供了理论依据。     

稀土(Y、Ce)掺杂b-FeSi_2光电性质的第一性原理研究

基于第一性原理赝势平面波方法,对稀土(Y、Ce)掺杂β-Fe Si2的几何结构、电子结构和光学性质进行了计算与分析。几何结构的计算表明,Y或Ce掺杂后β-Fe Si2的晶格常数改变,晶胞体积减小。电子结构的计算表明,掺入稀土后β-Fe Si2费米面附近的能带结构变得复杂,带隙变窄;总电子态密度发生了变化,Y的4d轨道电子态密度和Ce的4f轨道电子态密度主要贡献给费米面附近。光学性质的计算结果表明,Y或Ce掺杂后β-Fe Si2的静态介电常数明显提高,介电函数虚部ε2的峰值均向低能方向移动并且减弱,折射率n0明显提高,消光系数k的峰值减弱,计算结果为β-Fe Si2材料掺杂稀土改性的实验研究提供了理论依据。     

稀土元素La掺杂β-FeSi2的几何结构和电子结构的第一性原理研究

采用基于密度泛函理论的第一性原理赝势平面波方法,对稀土元素La掺杂β-FeSi2的几何结构、能带结构、态密度进行了理论计算.几何结构的计算表明:La掺杂后使β-FeSi2的晶格常数a、b、c都变大了,使得晶胞体积也相应增大;La掺杂β-FeSi2的置换位置为FeⅡ位.电子结构的计算表明:能带结构为直接带隙,禁带宽度变窄仅为0.013eV;费米面进入价带,能带数目增多,态密度峰值减小,费米面附近载流子浓度显著增大.这些结果为β-FeSi2光电材料掺杂改性的实验和理论研究提供理论依据.     

掺杂MgCNi3超导电性和磁性的第一性原理研究

从第一性原理出发，计算了MgCNi₃的电子能带结构.MgCNi₃中C 2p与Ni 3d轨道杂化使穿梭费米面上的Ni 3d能带表现出平面性，费米面落在态密度范霍夫奇异(vHs)峰的右坡上.vHs峰上大的电子态密度和铁磁相变点附近的自旋涨落是决定MgCNi₃超导电性的重要因素.研究了三种替代式掺杂对其超导电性和磁性的影响，发现电子掺杂使费米能级下滑到态密度较低的位置，导致体系转变为无超导电性的顺磁相；同构等价电子数的金属间化合物的轨道杂化，引起费米面上态密度的减少，降低了超导电性；而空穴掺杂使费米面向vHs峰值方向移动，虽然费米面上电子态密度增大可能提高超导电性，但增强了的Ni原子磁交换作用产生铁磁序，破坏了超导电性. 关键词： 电子结构 超导电性 磁性 掺杂     

锰掺杂二硅化铬电子结构和光学性质的第一性原理计算

采用基于第一性原理的密度泛函理论(DFT)赝势平面波方法计算了锰掺杂二硅化铬(CrSi2)体系的能带结构、态密度和光学性件质.计算结果表明末掺杂CrSi2属于间接带隙半导体间接带隙宽度△ER=0.35 eV;Mn掺杂后费米能级进入导带,带隙变窄,且间接带隙宽度△Eg=0.24 eV,CrSi2转变为n型半导体.光学参数发生改变,静态介电常数由掺杂前的ε1(O)=32变为掺杂后的ε1(O)=58;进一步分析了掺杂对CrSi2的能带结构、态密度和光学性质的影响,为CrSi2材料掺杂改件的研究提供r理论依据.     

C掺杂β-FeSi2的电子结构和光学特性研究

采用基于密度泛函理论的第一性原理赝势平面波方法,对C掺杂p-FeSi2的几何结构、能带结构、态密度和光学性质进行了理论计算.几何结构和电子结构的计算表明:C掺杂后使得β-FeSi2的晶格常数a和b减少,c变化不大,晶格体积减小;C掺杂后的 β-FeSi2能带结构仍为准直接带隙,禁带宽度变窄,直接带隙与间接带隙的能量差值不变,C的掺杂消弱了Fe的3d态电子,费米能级附近的电子态密度主要由Fe的3d态电子贡献.光学性质的计算表明:与未掺杂时相比,介电函数的实部ε1减少,虚部ε2的峰值减少并向高能方向有一微小的偏移,吸收系数有所降低.计算结果为β-FeSi2光电材料的应用和设计提供了理论指导.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.