金属簇络合物YCCo3(CO)9的合成与醛化性能的研究

本文提出一种常压下由硝酸钴和三卤化物经相转移催化合成钴簇络合物YCCo_3(CO)_9的新方法,并用该法合成了HCCo_3(CO)_9,ClCCo_3(CO)_9,PhCCo_3(CO)_9和EtOOCCo_3(CO)_9等四种络合物。考察了这些络合物对己烯的酸化活性和PhCCo_3(CO)_9对各种烯烃醛化时结构与活性的关系,以及它们的异构化和加氢活性。实验结果表明它们是一类在较缓和条件下具有较高活性和选择性的醛化催化剂。当反应温度130℃和压力40公斤/厘米~2时,己烯转化率达90％以上,选择性在80％以上。     

两相催化体系中长链烯烃氢甲酰化反应研究：—阳离子胶束的动力学作用机理

研究了以水溶性铑－膦配合物RhCl(CO)(TPPTS)2为催化剂,三苯基膦三磺酸钠（TPPTS）为配体,在阳离子表面活性剂十六烷基三甲基溴化铵（CTAB）存在下,水／有机物两相催化体系中,1－十二烯甲酰化反应与CTAB浓度的关系,为了进一步揭示阳离子表面活性剂在该反应体系中的动力学作用机理,分别应用分光光度法和光散射法,测定了1－十二烯在CTAB胶束中的增溶曲线和铑民位催化剂、配体TPPTS和1－十二烯对CTAB胶束摩尔质量的影响,结果表明,阳离子表面活性剂对长烯烃烯氢甲酰化两相催化反应具有加速作用,可能是由于;（1）催化剂及配体吸附于胶束界面并富集;（2）烯烃增溶于胶束内核,容易与催化活性物种发生配位反应。     

助剂前体ZnSO_4浓度对苯选择加氢制环己烯Ru-Zn催化剂性能的影响

共沉淀法制备了Ru-Zn催化剂,在ZrO_2作分散剂下考察了助剂前体ZnSO_4浓度对苯选择加氢制环己烯Ru-Zn催化剂性能的影响.并用X-射线衍射(XRD)、X-射线荧光光谱(XRF)、N_2-物理吸附、透射电镜(TEM)和X-射线光电子能谱(XPS)等手段对催化剂进行了表征.结果表明,当ZnSO_4前体浓度低于0.10 mol/L时,Ru-Zn催化剂中Zn以ZnO形式存在,在加氢过程中ZnO可以与反应修饰剂ZnSO_4反应生成(Zn( OH)_2)_3(ZnSO_4)(H_2O)_3盐.继续增加ZnSO_4前体浓度,催化剂中Zn以ZnO和NaZn_4(SO_4)(Cl)(OH)_6·6H_2O盐存在,在加氢过程中ZnO和NaZn_4(SO_4)(Cl)(OH)_6·6H_2O盐可以与反应修饰剂ZnSO_4反应生成(Zn( OH)_2)_3(ZnSO_4)(H_2O)_5.(Zn( OH)_2)_3(ZnSO_4)(H_2O)_x(x=3或5)盐的Zn~(2+)可以转移金属Ru的部分电子.因此,随ZnSO_4前体浓度的增加,(Zn( OH)_2)_3(ZnSO_4)(H_2O)_x的量逐渐增加,金属Ru失电子越多,催化剂活性越低,环己烯选择性越高.0.08 mol/L ZnSO_4前体制备Ru-Zn催化剂给出了59.1%的环己烯收率,而且该催化剂具有良好的重复使用性能和稳定性.     

羟基磷灰石负载HRh(CO)(TPPTS)3催化1-己烯氢甲酰化反应高选择性和特殊的异构化功能

采用浸渍法制备了以羟基磷灰石(HAP)载型水溶性铑络合物HRh(CO)(TPPTS)3/HAP催化剂(TPPTS=三苯基膦三间磺酸钠), 采用傅里叶变换红外光谱(FTIR)、 固体核磁共振波谱(31P CP-MAS NMR)、 扫描电子显微镜(SEM)、 电感耦合等离子发射光谱(ICP-OES)和比表面积测定(BET)等对催化剂进行了表征. 该催化剂在催化1-己烯氢甲酰化反应中表现出高活性和高选择性, 在优化条件下获得了100%的醛选择性和高转化频率(TOF=2465 h-1). 该催化剂还对1-己烯、 2-己烯和3-己烯表现出特殊的异构化功能. 该催化剂制备方法简单, 通过简单离心分离可以循环使用. 对HAP负载HRh(CO)(TPPTS)3的原理以及催化剂对烯烃异构化的机理进行了探讨.     

膦化聚苯乙烯担载四核羰基钴簇的合成和催化作用

合成了两种含膦聚苯乙烯载体和此二载体与四核羰基钴簇CO_4(CO)_8(μ_2-CO_2(μ_4-PPh)_2通过配体交换反应,合成两种担载的金属原子簇催化剂.用IR、VU-DRS和XPS表征担载簇配合物的结构.考察了担载簇催化剂对讣茑烯烃的氢甲酰化反应的催化活性.其活性顺序为:1-庚烯>环己烯>二异丁烯>2-辛烯>苯乙烯.     

水溶性钌-氢配合物催化1-已烯双键异构化反应研究

研究了水溶性钌-氢配合物RuHCl(TPPTS)3在水/有机两相体系中催化1-己烯双键异构化反应.考察了反应温度、时间、膦配体浓度、相转移催化剂CTAB浓度以及底物与催化剂摩尔比等对转化率和产物选择性的影响.在最佳条件下1-己烯转化率达到82.4%,2-己烯选择性21.2%,3-己烯61.2%,没有发现骨架异构化.催化剂可重复使用5次.     

反应修饰剂ZnSO_4和预处理对苯选择加氢制环己烯Ru-Zn催化剂性能的影响

共沉淀法制备了Ru-Zn催化剂,考察了反应修饰剂ZnSO_4和预处理对苯选择加氢制环己烯Ru-Zn催化剂性能的影响。结果表明,反应修饰剂ZnSO_4可以与Ru-Zn催化剂中助剂Zn O反应生成(Zn(OH)2)3(ZnSO_4)(H_2O)盐。随反应修饰剂ZnSO_4浓度增加,(Zn(OH)2)3(ZnSO_4)(H_2O)盐量逐渐增加,Ru-Zn催化剂活性逐渐降低,环己烯选择性逐渐升高。因为(Zn(OH)2)3(ZnSO_4)(H_2O)盐中的Zn2+可以使Ru变为有利环己烯生成的缺电子的Ruδ+物种,而且还可以占据不适宜环己烯生成的强Ru活性位。但当反应修饰剂ZnSO_4浓度高于0.41 mol·L-1后,继续增加ZnSO_4浓度,由于Zn2+水解浆液酸性太强,可以溶解部分(Zn(OH)2)3(ZnSO_4)(H_2O)盐,RuZn催化剂活性升高,环己烯选择性降低。环己烯选择性略微降低,是由于ZnSO_4溶液中大量的Zn2+可以与生成的环己烯形成配合物,稳定生成的环己烯,抑制环己烯再吸附到催化剂表面并加氢生成环己烷。在ZnSO_4最佳浓度0.61 mol·L-1下对Ru-Zn催化剂预处理15 h,Ru-Zn催化剂中助剂Zn O可以与ZnSO_4完全反应生成(Zn(OH)2)3(ZnSO_4)(H_2O)盐,在该催化剂上25 min苯转化68.2%时环己烯选择性和收率分别为80.2%和54.7%。而且该催化剂具有良好的稳定性和重复使用性能。     

Ru3(CO)9(TPPTS)3催化的水/有机两相芳香硝基化合物CO选择性还原的研究

将水溶性膦/钌配合物Ru₃(CO)₉(TPPTS)₃(TPPTS:三苯基膦三-间磺酸钠)用于以CO为还原剂的水/有机两相芳香硝基化合物选择还原为芳胺的反应,发现相转移催化剂对反应有明显的促进作用,其中以添加十六烷基三甲基溴化铵(CTAB)的效果最好.以邻氯硝基苯为底物考察了相转移催化剂浓度、NaOH浓度、反应温度、压力等对反应转化率和选择性的影响.当反应条件为120℃,4MPa,3mol/LNaOH时,反应8h,邻氯硝基苯的转化率和邻氯苯胺的选择性均可达到99.9%.而且对含有羰基、氰基的芳香硝基化合物也有很高的活性和选择性.催化剂循环3次后,邻氯硝基苯的转化率和邻氯苯胺的收率仍可达到92%.     

三核钨钼簇合物对苯乙烯氧化反应的催化

关于烯烃的催化氧化,报道较多。Takao等研究了苯乙烯在Ir和Rh络合物存在下的氧化反应;Collman曾报道环己烯在Vaska络合物[IrX(CO)(PPh_3)_2]催化下氧化成环己酮和环已烯氧化物。本文采用Cotton合成的簇合物[W_3O_2(CH_3CO_2)_6(H_2O)_3]Br_2·     

用于温控相转移纳米铑催化反应的水/有机两相新体系

在水/1-戊醇两相体系中实现了以温控配体Ph2P(CH2CH2O)22CH3为稳定剂的Rh纳米催化剂的温控相转移功能,并将其应用于烯烃催化加氢反应,在优化的反应条件下,环己烯的转化率和环己烷的收率均为99%.通过简单的相分离即可将催化剂从产物中分离出来,重复使用8次,其活性保持不变.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.