甲醇在铂修饰的氧化钛电极上电催化氧化行为的研究

运用电化学方法评价了电化学阴极还原-阳极氧化两步法制得的以钛为基体的铂修饰的钛氧化物(Pt-TiO_x/Ti)电极对甲醇电催化氧化的性能,结果表明,制得的修饰电极对甲醇氧化呈现了很高的电催化活性和好的稳定性.通过X光电子能谱(XPS)、扫描隧道显微镜(STM)和现场傅立叶变换红外(FTIR)反射光谱等技术,发现修饰电极对甲醇氧化具有高的电催化性能,可归属于纳米级Pt粒子在TiO_x中的高度分散及由于Pt和TiO_x的相互作用,使电极表面对甲醇氧化中间产物CO的吸附量大大降低.     

Electrocatalytic Characteristics of Hydrazine and Hydroxylamine Oxidation at Coumestan Modified Carbon Paste Electrode

A coumestan derivative modified carbon paste electrode (CMCPE) was used as a sensitive electrochemical sensor for determination of electrocatalytic of hydrazine and hydroxylamine. The mechanism of electrocatalytic oxidation of both hydrazine and hydroxylamine using CMCPE was investigated by cyclic voltammetry and polarization studies. The kinetic parameters such as the electron transfer coefficient, α, heterogeneous rate constant, k′, and exchange current density, j₀, for oxidation of hydrazine and hydroxylamine at the CMCPE surface were determined using cyclic voltammetry. Further more, the linear dynamic range, sensitivity and limit of detection for hydrazine and hydroxylamine detections were evaluated using differential pulse voltammetry.     

亚硫酸根在化学修饰电极上催化氧化的动力学表征

本文采用Saveant-Andrieux电催化反应动力学理论,表征了SO₃^2-在经Nation-Os(bpy)₃^2+/3+修饰后的玻碳电极上的电催化体系的动力学行为,用动力学区域图确定体系的动力学类型.当反应物浓度从8×10^-5变至1.28×10^-3(mol/L)时,体系始终遵循"SR"的动力学行为。     

Electrocatalytic Oxidation of Methanol on a Nickel‐Porphyrin IX Complex Modified Glassy Carbon Electrode in Alkaline Medium

Electrocatalytic oxidation of methanol on a glassy carbon disc electrode modified with Ni(II)‐hematoporphyrin IX, complex and conditioned by potential recycling in a limited range (between 100 and 600 mV vs. SCE) in 0.10 M NaOH solution, abbreviated as NiOHPME(A), was studied by cyclic voltammetry in alkaline medium. The results were compared with those obtained for a NiO modified glassy carbon electrode, NiOME, prepared in similar conditions. The findings show that the NiOHP film at NiOHPME(A) behaves as an efficient electrocatalyst for the oxidation of methanol in alkaline medium via Ni(III) species with the cross‐exchange reaction occurring throughout the layer at a low concentration of methanol and for a thin film of modifier. A plausible mechanism was proposed for catalytic oxidation of methanol at NiOHP modified electrode. Moreover, the effects of various parameters such as the scan rate, methanol concentration, thickness of NiOHP film and the real surface area of modified electrode on the oxidation of methanol were investigated. Finally, it has been shown that the NiOHPME(A) has a long‐term stability toward the oxidation of methanol.     

Electrocatalytic Oxidation of Amines on a Mediator‐Modified Electrode by Electrochemical Copolymerization of Nitroxyl Radical Precursor Containing Pyrrole Side Chain and Bithiophene

This paper describes the electrocatalytic oxidation of amines on TEMPO (2,2,6,6‐tetramethylpiperidine‐1‐oxyl)‐modified electrodes prepared by electrochemical copolymerization of TEMPO precursor containing pyrrole side chain and 2,2′‐bithiophene. The modified electrode exhibits electrocatalytic activity for the oxidation of primary and secondary amines. Cyclic voltammetric studies showed that the peak current of the cyclic voltammogram increased linearly with increasing concentration of amine in the sample solution.     

Electrocatalytic Oxidation of Dopamine at Sol‐Gel Carbon Composite Electrode Chemically Modified with Copper Hexacyanoferrate

An organic‐inorganic composite electrode was prepared by the sol‐gel method. For this purpose the carbon composite electrode (CCE) was modified with copper hexacyanoferrate (CuHCF). The CuHCF‐CCE was prepared by two methods. In one method CCE was prepared in one step and in another method the electrode was prepared in a two‐step process. The electrochemical behavior of the CuHCF modified electrode was studied by cyclic voltammetry; the modified electrode shows a pair of peaks with a surface‐confined characteristic in a 0.1 M phosphate buffer (pH 7) with K⁺ cation, as a supporting electrolyte. The CuHCF‐CCE showed electrocatalytic activity toward oxidation of Dopamine (DA). The kinetics of the catalytic reaction was investigated by using chronoamperometry. The average value of the rate constant for catalytic reaction and the diffusion coefficient were calculated. At a 0.85 V potential under hydrodynamic conditions (stirred solution), the oxidation current is proportional to the dopamine concentration, and the calibration plot was linear over the concentration range of 5‐85 μM.     

石墨烯修饰玻碳电极对多巴胺的电催化氧化

通过3-巯丙基三乙氧基硅烷(METMS)将氧化石墨烯(GO)固载到玻碳电极(GCE)表面, 用电化学方法还原GO制备石墨烯修饰玻碳电极(rGO-METMS-GCE). 利用傅里叶变换红外光谱(FTIR)、 拉曼光谱(Raman)、 扫描电子显微镜(SEM)和原子力显微镜(AFM)等技术对GO和rGO-METMS-GCE的结构和表面形貌进行表征. 采用循环伏安(CV)和差分脉冲溶出伏安(DPV)法研究了rGO-METMS-GCE对多巴胺(DA)的电催化氧化性能及反应机理. 结果表明, 与裸GCE相比, DA在rGO-METMS-GCE电极上的氧化还原峰电流(i_pa和i_pc) 增大4倍, 氧化峰电位负移106 mV, 氧化峰与还原峰电位差(ΔE_p)从202 mV降低至66 mV, DA电化学氧化可逆性明显改善, 表明rGO-METMS-GCE对DA电化学氧化具有显著电催化作用. DA在rGO-METMS-GCE上的反应机理为单电子转移过程.     

铂微粒修饰的氧化钛电极对甲醇的电催化氧化性能

直接甲醇质子交换膜燃料电池(DMPEMFC)可用作未来电动车辆的动力电源,但要达到实际应用还有大量问题有待进一步解决.目前限制DMPEMFC实际应用的主要问题是甲醇阳极氧化催化剂低的活性、高的价格及催化剂的毒化.     

Electrocatalytic Oxidation and Determination of Sulfite with a Novel Copper‐Cobalt Hexacyanoferrate Modified Carbon Paste Electrode

The electrocatalytic oxidation of sulfite has been studied at a stable electroactive thin film of copper‐cobalt hexacyanoferrate (CuCoHCF) hybrid electrodeposited on a carbon paste electrode (ECMCPE). A linear range of 5 μM to 5 mM of sulfite, with an experimental detection limit of 1 μM, was obtained using the cyclic voltammetric method. The oxidation of sulfite showed no significant fouling effect on the modified electrode surface at sulfite concentrations below 5 mM. The proposed modified electrode exhibited several attractive features, including simple preparation, fast response, good stability and repeatability, and could be applied to sulfite determination in real samples.     

硫代硫酸盐在铂电极上的电化学氧化行为

用循环伏安法测定了硫代硫酸盐在铂电极上的电化学氧化行为, 结果表明, 其电化学氧化行为与体系的pH和扫描速度密切相关. 当pH为5~6时, 硫代硫酸盐的循环伏安曲线出现三个氧化峰, 峰电位分别在0.05 V、0.58 V和1.02 V附近, 随pH值升高和扫描速度的降低, 0.05 V附近的氧化峰逐渐变得明显, 同时各氧化峰的峰电位与扫描速度的对数, 峰电流与扫描速度的平方根均成很好的线性关系；当pH为8~9时, 硫代硫酸盐的循环伏安曲线出现三个明显的氧化峰, 峰电位分别在0.05 V、0.91 V和1.22 V附近. 随扫描速度降低, 循环伏安曲线出现交叉, 体系呈现明显的电化学振荡行为；但当pH=10时, 1.22 V附近的氧化峰消失. 硫代硫酸盐的电化学氧化行为非常复杂, 电化学氧化机制随体系pH的变化而变化.     

Electrocatalytic Oxidation of Sulfite on a Cobalt Pentacyanonitrosylferrate Film Modified Glassy Carbon Electrode

The electrocatalytic oxidation of sulfite has been studied on the cobalt pentacyanonitrosylferrate modified glassy carbon electrode (CoPCNF). The CoPCNF films on the glassy carbon electrodes show an excellent electrocatalytic activity toward the oxidation of sulfite in 0.5 M KNO₃. The kinetics of the catalytic reaction was investigated by using cyclic voltammetry, rotating disk electrode (RDE) voltammetry and chronoamperometry. The average value of the rate constant, K, for the catalytic reaction and the diffusion coefficient, D, were evaluated by different approaches for sulfite and found to be 2.9×10² M^?1s^?1 and 4.6×10^?6 cm²s^?1, respectively. At a fixed potential under hydrodynamic conditions (stirred solutions), the oxidation current is proportional to the sulfite concentration and the calibration plot was linear over the concentration range 5×10^?6–1×10^?4 M. The detection limit of the method is 3×10^?6 M., low enough for the trace sulfite determination.     

CO在铂修饰的氧化钛电极上电催化氧化行为的研究

通过阴极还原-阳极氧化法制备了Pt—TiO2／Ti电极，研究了CO在该电极上的电化学行为和电极制备条件对CO电催化氧化的影响．结果表明，与Pt电极相比．CO在Pt—TiO2／Ti电极上的氧化峰峰电位负移了100mV，并且表现出较好的稳定性．通过XPS技术对Pt—TiO2／Ti电极进行了表征．发现Pt以金属形式存在，Ti以TiO2形式存在．Pt—TiO2／Ti电极能抗CO中毒的原因可能是因为TiO2的掺杂使引起催化剂中毒的桥式吸附的CO物种在复合催化剂上的吸附率较低所致．     

Electrocatalytic Oxidation of Estrogenic Phenolic Compounds at a Nickel‐Modified Glassy Carbon Electrode

This paper demonstrates for the first time, successful electrocatalytic oxidation of electroactive estrogenic phenolic compounds (EPCs) at a nickel‐modified glassy carbon electrode (Ni‐GCE). The electrode was evaluated in terms of electrocatalytic activity, sensitivity, linear dynamic range, limit of detection, and response stability. In comparison to bare glassy carbon electrode, current amplification was observed for EPCs at Ni‐GCE, for example, for a 40 µM estrone at Ni‐GCE was amplified by a factor of 1224. The Ni‐GCE gave good figures of merit with no evidence of electrode fouling. As an example, the limit of detection (S/N=3) for 17β‐estradiol was 100 nM and the response precision (n=5) was 3.4 %.     

血红素修饰电极电催化氧化测定儿茶酚类化合物

采用循环伏安法将血红素修猸于玻碳电极表面，制备出对儿茶酚类化合物具有电催化氧化作用的血红素修饰电极（Ｈｅｍｅ／ＧＣ）。该电极上的催化氧化峰电流与邻苯二酚、多巴胺、肾上腺素等儿茶酚类化合物的浓度在各自响应的范围内有良好的线性关系，检测下限为４￣８×１０＾－８ｍｏｌ／Ｌ。用于多巴胺和肾上腺素药物针剂的测定结果令人满意，回收率９８￣１０２％。     

新型乙基溴硫磷印迹膜/纳米金化学修饰电极的研制及应用

以恒电位将金纳米粒子(AuNP)沉积于玻碳电极表面,在模板分子乙基溴硫磷存在下通过循环伏安法将L-半胱氨酸组装到金纳米粒子修饰的玻碳电极上,制备了可选择性识别乙基溴硫磷的L-Cys/ AuNP/ GCE印迹膜电极.结果表明,该电极具有良好的稳定性和重现性,对乙基溴硫磷的线性响应范围为2.5 ～17.5μmol/L,检出...     

Nano TiO2 Modified Carbon‐ceramic Electrode and Its Application for Electrocatalytic Oxidation of NADH

The electrocatalytic oxidation of nicotinamide adenine dinucleotide (NADH) was studied on nanoTiO₂ modified sol‐gel electrode, using cyclic voltammetry, chronoamperometry and differential pulse voltammetry as diagnostic techniques. It is demonstrated that TiO₂ nanoparticles on sol‐gel network catalyze the oxidation of NADH in the absence of any electron transfer mediators. Effect of various parameters such as pH, scan rate, TiO₂ percentage on the response of modified electrode was studied. In addition, scanning electron microscopy (SEM) was used to characterize the surface morphology of the spots. A dynamic range between 0.5–50 μM with detection limit of 0.35 μM was obtained with DPV studies. This method was successfully used for determination of NADH in cucumber cotyledons samples. The electrode showed relatively good stability over more than 2 months.     

硫堇衍生化自组装膜修饰金电极的电化学性质及其对抗坏血酸的电催化氧化

将硫堇共价键合到自组装在金电极表面的半胱胺单分子层上,制成了衍生化自组装单分子膜修饰电极,并用电化学方法研究了它的电化学性质.循环伏安图显示其在pH＝7.7的磷酸盐缓冲液中,于－0.45～＋0.50V(vs.SCE)范围内有2对氧化还原峰.峰电位分别为E_pa¹＝214mV。E_pc¹＝82mV,E_pa2＝－75mV,E_pc2＝－160mV(vs.SCE).pH在5.0～9.0范围内,峰1有2个质子参与反应,峰2有1个质子参与反应.它的表面电子转移速率常数k_s＝0.02S^－1.此膜对抗坏血酸的氧化有催化作用,其氧化过电位较在裸金电极上降低了约250mV.催化电流与抗坏血酸的浓度在1.0×10^-6～4.0×10^-3mol/L范围内呈良好的线性关系.抗坏血酸催化氧化的异相速率常数为2.68×10^-3cm/s.     

Electrocatalytic Oxidation of Acyclovir on Poly(p‐Aminobenzene Sulfonic Acid) Film Modified Glassy Carbon Electrode

Acyclovir is an antiviral effective drug active compound. A glassy carbon electrode (GCE) was modified with an electropolymerized film of p‐aminobenzene sulfonic acid (p‐ABSA) in phosphate buffer solution (PBS). The polymer film‐modified electrode was used to electrochemically detect acyclovir. Polymer film showed excellent electrocatalytic activity for the oxidation of acyclovir. The anodic peak potential value of the acyclovir at the poly(p‐ABSA) modified glassy carbon electrode was 950 mV obtained by DPV. A linear calibration curve for DPV analysis was constructed in the acyclovir concentration range 2×10^?7–9×10^?6 mol L^?1. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 5.57×10^?8 and 1.85×10^?7 mol L^?1 respectively. The proposed method exhibits good recovery and reproducibility.     

纳米铂微粒修饰电极上甲醛电催化氧化的电位振荡和电流振荡

通过阴极还原-阳极氧化法制备了钛基纳米铂微粒修饰电极, 扫描电镜观察发现, 分布于钛基体表面的氧化钛膜三维网状孔道中的纳米铂微粒具有高度分散状态. 采用多种电化学手段在该电极上不仅观察到甲醛在恒电流条件下产生的电位振荡, 而且在循环伏安和恒电位两种条件下均观察到强烈的电流振荡, 这进一步证明高度分散的纳米铂微粒使电极的催化活性大大提高, 促进了甲醛及其毒化中间产物的电催化氧化过程, 从而有利于电极上电化学振荡的产生. 研究结果还表明, 甲醛底物浓度、硫酸介质浓度、恒电位或恒电流大小等多种因素对振荡强度、范围或类型会产生规律性的影响.     

一种新型的钛基纳米多孔网状铂电极对甲醇氧化反应的电催化活性

利用水热法一步制备出钛基纳米多孔网状铂催化剂(nanoPt/Ti), 并研究了它对甲醇氧化反应的电催化活性.