Terpolymers. III. Isochronal viscoelastic parameters for terpolymers of vinyl stearate,vinyl acetate,and vinyl chloride

Isochronal viscoelastic parameters were collected for many of the copolymers, terpolymers, and diluent mixtures whose mechanical properties at ambient temperatures were reported in the preceding paper. In the polymeric systems, vinyl stearate, acting as the primary internal plasticizer, was introduced into terpolymers by displacing vinyl acetate from base copolymers of vinyl acetate and vinyl chloride, across the range of composition. In the diluent mixtures, poly(vinyl chloride) was plasticized by di-2-ethylhexyl phthalate across the range of compositions. For direct comparison with the mixtures, vinyl chloride was plasticized by copolymerization with vinyl stearate across the same range of compositions. Moduli for the co- and terpolymers reached the low values characteristic of soft materials at room temperature only through a short range of vinyl stearate composition. At higher internal plasticizer compositions, side-chain crystallization stiffened the samples and raised their moduli. In contrast, moduli for the mixtures decreased steadily with increase in diluent at ambient temperature. The effective use temperature ranges were narrow for the co- and terpolymers but broad for the mixtures. Curve broadening was similar for both types of systems, but reached a maximum at about 40 weight-% plasticizer for the diluent mixtures. The slopes of the glassy modulus with decreasing temperature at 50°C below T_g for the vinyl stearate copolymers were relatively large. However, moduli close to that of poly(vinyl chloride) were reached only near the temperature range associated with the γ-transition. Consequently, this behavior was attributed to motions of the side chains in the glassy matrix. Room temperature moduli, which could be obtained before the onset of melting, were correlated with the fractional side-chain crystallinity for polymers having a high vinyl stearate content. From this relation, the modulus for the hexagonal crystal form of the side-chain crystallites of poly(vinyl stearate) was estimated to be 1.2×10¹⁰ dynes/cm². Moduli for the glassy amorphous phase of this same polymer appeared to have one sixth of this value at 40°C below the glass transition. The glass transition temperature occurred about 10° below the inflection temperature at 10⁹ dynes/cm², as an average for all of the systems studied.     

Polyblends. I. Mechanical properties of polyblends of butadiene–acrylonitrile elastomers and copolymers of vinyl stearate and vinyl chloride

Several nitrile rubber elastomers were polyblended, across the composition range, with selected polymeric compositions containing vinyl chloride. The compositions incorporated were (a) bulk poly(vinyl chloride) (PVC); (b) copolymers of vinyl stearate and vinyl chloride containing, respectively, 0.21, 0.36, and 0.47 weight fraction of the vinyl ester; and (c) mixtures containing the same weight fractions of di-2-ethylhexyl phthalate (DOP) with PVC. Mechanical, viscoelastic, optical, and volatility properties were studied on all blends in this first paper. To accurately compare the mechanical properties of polyblends of different systems, a criterion of mechanical equivalence was taken as the observance of similar stresses at break for compositions selected to have identical 100% moduli. Optimum mechanical equivalence, therefore, occurred at the largest ratios of 100% modulus to break stress for all systems compared. Optimum mechanical property equivalence was observed for NBR blends with PVC and for similar blends of both internally and externally plasticized systems containing 0.21 weight fraction of plasticizer. However, considerably more nitrile rubber was needed for PVC blends to acquire the properties of the plasticized systems. Mechanical equivalence was observed, but was not optimum for systems having more plasticizer because tensile strengths were lower. Polyblending with NBR improved the toughness and low-temperature properties of starting vinyl stearate copolymers. Improved toughness was indicated by the expansion of areas under stress–strain curves. Refractive index matching appeared to explain the transparency of the best films and their relative freedom from haze. On heating at 85°C, poly(vinyl chloride) and the copolymer polyblends suffered no volatility loss. Volatility of DOP from the blends was 1.5 times greater than for PVC–DOP mixtures. Because modulus–temperature curves and mechanical T_g values of the filler component shifted with composition, the mechanical behavior of these blends was in harmony with an accepted standard of interdomain compatibility.     

Alloying of poly(vinyl chloride) to reduce plasticizer migration

Concern over the migration of low molecular weight plasticizer from flexible poly(vinyl chloride) (PVC) used in toys and medical products has spearheaded the commercialization of a number of plasticizing polymers. In this study the plasticizing behavior of an ethylene/vinyl acetate/carbon monoxide terpolymer (Elvaloy® from DuPont) was investigated. Blends of PVC, Elvaloy 742, and dioctyl phthalate (DOP) were processed on a twin‐roll mill and compression molded into plaques. These materials were characterized in terms of their hardness, glass‐transition temperature (T_g), clarity, mechanical properties, and plasticizer migration behavior. The ratios of PVC/DOP/Elvaloy investigated were determined by experimental design. Using this approach it was possible to model the results and produce contour plots to map out the properties of a wide range of formulations. It was confirmed that Elvaloy 742 is compatible with PVC and has a plasticizing effect: this was demonstrated both in terms of a reduction in Shore A hardness and a reduction in T_g. Plasticizer migration was reduced in proportion to the amount of liquid plasticizer replaced. Plasticizing with Elvaloy gave an improvement in tear strength. However, at constant hardness there was no improvement in tensile strength from replacing DOP with Elvaloy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2022–2031, 2004     

Plastification of poly(vinyl chloride) by polymer blending

Blends of poly(vinyl chloride) (PVC) with different copolymers have been studied to obtain a plasticized PVC with improved properties and the absence of plasticizer migration. The copolymers used as plasticizers in the blends were acrylonitrile butadiene rubber, ethylene vinyl acetate (EVA), and ethylene-acrylic copolymer (E-Acry). Blends were studied with regard to their processing, miscibility, and mechanical properties, as a function of blend and copolymer composition. The results obtained were compared with those of equivalent compositions in the PVC/dioctyl phthalate (DOP) system. Better results than PVC/DOP were obtained for PVC/acrylonitrile butadiene rubber blends. The plasticizing effect on PVC of EVA and E-Acry copolymers was similar to that of DOP. It is shown that crosslinking PVC/E-Acry blends or increasing the vinyl acetate content in PVC/EVA blends, are alternatives that can increase the compatibility and mechanical properties of these blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1303–1312, 2000     

Synthesis of a bio-based plasticizer from vanillic acid and its effects on poly(vinyl chloride)

A new bio-based plasticizer, VA8-8, was prepared derived from vanillic acid, and its structure was verified by nuclear magnetic resonance. It was incorporated into poly(vinyl chloride) (PVC) to replace dioctyl phthalate (DOP), and its plasticizing performance was evaluated. The results indicated that VA8-8 shows good compatible with PVC resin, and has a excellent plasticizing effect for PVC. When DOP was partially or completely substituted with VA8-8, the T_g value PVC blends dropped from 34.6 to 24.3°C and the elongation at break increased from 196.4% to 301.9%, suggesting the enhanced plasticizing efficiency of plasticizer. The plasticizing mechanism was also simulated, and the interactions between VA8-8 and PVC molecules were discussed. The thermogravimetric analysis showed VA8-8 can more effectively improve the thermal stability of PVC than DOP. In addition, the migration resistance of VA8-8 was generally superior to that of DOP. Therefore, VA8-8 is a comparable to or better plasticizer than DOP, and it is a promising alternative plasticizer for PVC.     

Novel network polymer electrolytes containing fluorine and sulfonic acid lithium prepared by ultraviolet polymerization

Poly(vinyl alcohol) (PVAL) and vinyl acetate‐vinyl alcohol copolymers (VAVAL) were esterified with 3,5‐dinitrobenzoyl chloride using the cycled urea N,N′‐dimethylpropyleneurea (1,3‐dimethyl‐3,4,5,6‐tetrahydro‐2(1H)‐pyrimidinone) (DMPU) as the solvent. Vinyl alcohol‐vinyl‐3,5‐dinitrobenzoate copolymers (VALVDNB) and vinyl acetate‐vinyl‐3,5‐dinitrobenzoate copolymers (VAVDNB) were obtained. High degrees of esterification were obtained when PVAL was esterified (86%). The degree of transformation was determined by ¹H‐NMR as well as by chemical analysis, and the structure of the resulting polymers by means of IR spectroscopy and ¹H‐ and ¹³C‐NMR. The microstructure of PVA, PVAL, VAVAL copolymers and VALVDNB copolymers were determined from ¹H‐ and ¹³C‐NMR techniques. The sequence distributions for VAVAL copolymers prepared by base‐catalyzed transesterification of PVA were blocky, while the distributions were close to random for VALVDNB copolymers obtained by esterification of PVAL. Thermal properties were studied by DSC. The T_g values of VAVAL, VALVDNB, and VAVDNB copolymers as a function of copolymer compositions were determined. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyhedral oligomeric silsesquioxane as a novel plasticizer for poly(vinyl chloride)

This study focuses on investigating the use of polyhedral oligomeric silsesquioxanes (POSS) to plasticize poly(vinyl chloride) (PVC). Conventional organic plasticizers for PVC, such as dioctyl phthalate (DOP), are somewhat volatile, leading to plasticizer loss and unwanted deterioration of the material properties over time. Previous experimental results indicate that methacryl-POSS, which is much less volatile due to its hybrid organic-inorganic structure, has the ability to plasticize PVC. Methacryl-POSS is miscible in the PVC only up to 15 wt%, thereby limiting its suitability as a plasticizer. However, through the use of ternary compositions it is possible to increase the proportion of methacryl-POSS in PVC substantially. The T_g of appropriately formulated ternary PVC/POSS/DOP compounds can be reduced to near room temperature, and these materials exhibit desirable ductile behavior. Binary (PVC/DOP) and ternary (PVC/POSS/DOP) compounds formulated to the same T_g values showed considerably different mechanical properties. Such findings reveal the possibility of using POSS to engineer the mechanical properties of plasticized PVC.     

Evaluation of butyl stearate,butyl oleate,butyl ricmoleate,and methyl lmoleate as poly(vinyl chloride) plasticizers

An investigation of butyl stearate, butyl oleate, butyl rieinoleate, and methyl lmoleate was made to determine the extent of their compatibility with poly(vinyl chloride) and their plasticizing effects on the physical, properties of the resulting molded sheets. These monoesters were evaluated as the sole plasticizer and in combination with DOP. The results showed the materials to have limited compatibility in general, being less than 10% of the total mix. In combination with DOP these compounds were found to improve the plasticizer efficiency, color, low temperature flexibility, and heat stability of the molded poly (vinyl chloride) sheets over those containing DOP as the sole plasticizer. Tensile strength, per cent elongation, and light stability properties were essentially comparable to those found for pure DOP.     

Graft polymerization of vinyl acetate onto starch. Saponification to starch–g–poly(vinyl alcohol)

Graft polymerizations of vinyl acetate onto granular corn starch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinylacetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. However, over half of the polymer was present as ungrafted poly-(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficiency. However, grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate-methyl methacrylate was carried out near 0°C, although conversion of monomers to polymer was low and grafted polymer contained 40-50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch–g–poly(vinyl acetate) to starch–g–poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch–g–poly(vinyl alcohol) in hot water was less than 50%; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized starch for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch–g–poly(vinyl acetate) with about 35% add-on, and a grafting efficiency of about 40% was obtained. A film cast from a starch–g–poly(vinyl alcohol) copolymer in which homopolymer was not removed exhibited a higher ultimate tensile strength than a comparable physical mixture of starch and poly(vinyl alcohol).     

Electrical properties of poly(vinyl chloride) compositions

A sample of poly(vinyl chloride) (PVC) and a polar plasticizer consisting of dioctyl phthalate (DOP) and dibutyl phthalate (DBP) was prepared and found to possess inconvenient electrical properties (permittivity, dielectric loss, and conductivity). Different samples of PVC compositions were formulated from the PVC–DOP–DBP system and also variable proportions of a copolymer of 1-octadecene-maleic anhydride or its hexadecylester. Lead stearate as a heat stabilizer and kaolin as a filler were added. The effect of copolymer structure on the electrical properties of the PVC–DOP–DBP system was studied to obtain a plasticized PVC of good electrical insulation character. © 1993 John Wiley & Sons, Inc.     

Poly(vinyl chloride) plasticized with succinate esters: synthesis and characterization

Phthalates pose adverse health effects due to their propensity to leach and the most common, di(2-ethylhexyl) phthalate (DEHP) and di-n-octyl phthalate (DOP), are petroleum-based. Conversely, di-esters, succinates are biobased (produced from fermentation of biomass), biodegradable, and therefore potential sustainable replacements for phthalates. A series of succinates, di-octyl succinate (DOS), di-hexyl succinate (DHS), di-butyl succinate (DBS), and di-ethyl succinate (DES), were mixed with poly(vinyl chloride) (PVC). The interaction of the plasticizer ester carbonyl with PVC shows an average −5 cm⁻¹ shift of the carbonyl absorbance peak energy. The glass transition temperatures (T _g), were monitored by differential scanning calorimetry and dynamic mechanical analyses. The T _gs of DOS and DHS plasticized PVC were significantly lower than DOP plasticized PVC at a lower percent mass. On the other hand, PVC plasticized with either DBS or DES exhibited a similar trend in lowering the T _g as that of DOP plasticized PVC.     

Synthesis,characterization, and properties of poly(vinyl acetate)‐ and poly(vinyl alcohol)‐grafted chitosan

Graft copolymers of chitosan and vinyl acetate were synthesized by free radical technique using cerium (IV) as the initiator. Under controlled conditions, as much as 92% grafting with a grafting yield of 30–40% could be achieved. Chitosan‐g‐poly(vinyl alcohol) copolymers were derived by the alkaline hydrolysis of the chitosan‐g‐poly(vinyl acetate) precursor. Thermogravimetric, FTIR, and X‐ray diffraction analyses of chitosan and the copolymers confirmed the grafting reaction between chitosan and vinyl acetate and also the subsequent hydrolysis. Both the copolymers possessed very good film‐forming properties. Grafting resulted in a significant increase in mechanical strength of both the copolymers in the dry condition. Chitosan‐g‐poly(vinyl acetate) (CH‐PVAc) proved more hydrophobic than did pure chitosan, whereas chitosan‐g‐poly(vinyl alcohol) (CH‐PVOH) exhibited enhanced hydrophilicity as evident from their swelling characteristics and contact angle measurements. The enhanced swelling of CH‐PVOH was ascribed to the presence of the pendant poly(vinyl alcohol) group. At pH 1.98, the CH‐PVAc copolymer films showed greater stability than do pure chitosan films, which is highly beneficial for specific biomedical applications. Both the copolymers showed lower glass transition temperature than do pure chitosan. Grafting did not affect the overall thermal stability, and the differential thermogram substantiated the grafting. The investigations indicate that the synthetic–natural hybrid copolymers having desirable mechanical properties and tailored hydrophilic/hydrophobic characteristics are realizable. These polymers could be exploited for varied biomedical applications. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1852–1859, 2007     

Rheological behavior of partially hydrolyzed poly(vinyl acetate-co-ethylene)

The rheological behavior of partially hydrolyzed poly(vinyl acetate-co-ethylene) (VAE) was investigated, using a Rheometrics Dynamic Mechanical Spectrometer. For the investigation, measurements of storage modulus (G′), loss modulus (G″) and loss tangent (tan δ) of the materials were recorded as functions of temperature at a fixed frequency (i.e., using temperature scans) and, also, as functions of frequency at a fixed temperature (i.e., using frequency scans). For the hydrolysis, three different grades of copolymer (containing 34, 47, 62 mol% of vinyl acetate) were used to yield poly(vinyl acetate-co-ethylene-co-vinyl alcohol) (VAEOH) with varying amounts of hydroxyl group. For comparison purposes, the viscoelastic properties of blends of VAE copolymer with poly(vinyl alcohol) (PVOH), having varying blend compositions, were also measured. The blends were prepared by first mixing a solution of VAE copolymer, which was dissolved in a toluene/dichloroethane mixed solvent, and an aqueous solution of PVOH, and then freeze drying the mixture to a constant weight. Also measured were the glass transition temperature (T_g) of the VAE copolymers and the T_g and melting point (T_m) of the VAEOH terpolymers, using a DuPont Thermal Analyzer equipped with a 910 DSC Module. It has been found that (1) introduction of hydroxyl group into the backbone of the amorphous VAE copolymer has made the resulting VAEOH terpolymer semicrystalline; (2) the T_m, T_g, G′, and the complex viscosity (η^*) of the VAEOH terpolymers increase with increasing amounts of hydroxyl group; (3) the physical blending of PVOH with VAE copolymer has not affected the T_g of the VAE copolymer; (4) the G′ and η^* of the VAE/PVOH blends are found to increase with the amount of PVOH in the blend. The use of logarithmic plots of G′ versus G″ has been found to be very useful for discerning the differences in the structure of the materials tested.     

Effect of ketal group in castor oil acid-based plasticizer on the properties of poly(vinyl chloride)

Two castor oil acid esters containing a ketal or ketone group (KCL or CL), as alternative plasticizers for poly(vinyl chloride) (PVC), were prepared. The structures were confirmed by ¹H NMR and FTIR spectroscopies. The effects of the presence of a ketal or ketone group in these compounds on PVC plasticization were examined. The DMA and SEM results showed that both plasticizers were miscible with PVC and exhibited excellent plasticizing properties, compared to those of dioctyl phthalate (DOP). The PVC plasticized by KCL displayed a lower T_g value of 20.6 ° C, which was lower than that of PVC plasticized with DOP (22.3 ° C) and PVC plasticized with CL (40.5 ° C). Tensile tests indicated that PVC plasticized using KCL showed a 37% higher of elongation at break than PVC plasticized by CL and 30% higher than PVC plasticized by DOP. The plasticizing mechanism was also investigated. Moreover, exudation, volatility, and extraction tests, along with TGA indicated that the presence of ketal groups effectively improved the migration resistance of plasticizer and the thermal stability of PVC blends. Taken together, introducing ketal groups into plasticizer might be an effective strategy for improving its plasticizing efficiency.     

Terpolymers. I. The mechanical properties and transition temperatures of terpolymers of n-octadecyl acrylate,ethyl acrylate,and acrylonitrile

Earlier work revealed that the internal plasticization of polyacrylonitrile by the higher n-alkyl acrylates or N-n-alkylacrylamides yielded only brittle copolymers. This difficulty was circumvented in the present work by starting with copolymers of acrylonitrile and ethyl acrylate, over the range of compositions, and further modifying these by incrementally displacing the ethyl acrylate in each recipe by n-octadecyl acrylate through terpolymerization. In this way, the stepwise small reduction in T_g for the base ethyl acrylate–acrylonitrile copolymers was greatly increased for each of the terpolymers. Compositions were obtained ranging from glassy, brittle terpolymers, with glass transitions above room temperature, to soft plasticized polymers having sufficient polar networks retained from the nitrile to confer useful properties. The decline in the glass temperature was shown to be dependent on the free volume conferred by the side-chain methylene groups of each acrylate ester. In contrast, the decline in tensile and flexural strengths and moduli for the terpolymers having glass transitions above room temperature was produced entirely by the presence of the methylene groups of the 18-carbon ester. The glass transition region corresponded to room temperature when the acrylonitrile content of the base copolymer had been reduced to 50 mole-%. Terpolymers of this nitrile content and lower had the low moduli and large elongations of plasticized compositions. An equation was developed which correlated empirically the glass transitions and the mechanical properties with the weight fraction of the acrylate esters for the glassy terpolymers.     

Rosin‐derived poly(vinyl chloride) plasticizer: Synthesis,structure, and properties

In this work, rosin‐based plasticizer was synthesized by Diels–Alder (DA) and esterification. First, the maleopimaric acid (RT) was obtained by DA between the double bond of rosin and maleic anhydride. Then, the carboxyl group and anhydride group of RT was esterified with tetrahydro geraniol to obtain the rosin‐based polyacid esters (RTT) under the catalysis of p‐toluene sulfonic acid. The structure of RT and RTT was detected by FTIR and ¹H‐NMR. RTT was used as main plasticizer to obtain plasticized polyvinyl chloride (PVC) materials and compared with DOP. The results showed that RTT improved the thermal stability and reduced T_g of PVC film. Plasticized PVC films had excellent mechanical properties with the elastic modulus of ?4,793.67 MPa and tensile strength of ?111.86 MPa, higher than that of pure PVC and DOP‐6. RTT showed better volatility stability, migration, and solvent extraction in PVC compared to DOP. J. VINYL ADDIT. TECHNOL., 26:180–186, 2020. © 2019 Society of Plastics Engineers     

Investigation of the compatibility of butadiene—acrylonitrile copolymers with poly(vinyl chloride)

Various methods were used to study the compatibility of butadiene-acrylonitrile copolymers with poly(vinyl chloride). These blends were investigated by phase contrast microscopy, differential scanning calorimetry and torsion pendulum analysis. We conclude that the copolymers are compatible with poly(vinyl chloride) in all PVC compositions within the range 23–45% acrylonitrile. These blends exhibit a single T_g in the torsion pendulum studies and differential scanning calorimetry studies and follow a Fox expression in the variation of T_g with composition. Experimental densities are also higher than those calculated assuming volume additivity, implying better packing and a negative heat of mixing leading to molecular compatibility.     

The influence of filler particles and polymer structure on the mobility of polymer molecules

The presence of carbon filler has been shown to cause a change in the glass transition temperature of polymers. For poly(vinyl chloride) and two of its copolymers with 10 and 15% vinyl acetate an increase in T_g was observed when Graphon C Carbon was added. The increase was greater when the proportion of vinyl acetate was greater. Polar vinyl acetate units allow stronger adsorption of polymer onto the carbon. Brittle polymers such as polystyrene and poly(methyl methacrylate) showed scattered T_g's when filled with carbon. The changes were not a function of concentration. It is postulated that the thermal stress of these polymers is increased in the presence of filler.     

Copolymerization of pentachlorophenyl acrylate with vinyl acetate and ethyl acrylate. Polymer-bound fungicides

Copolymers of pentachlorophenyl acrylate (M₁) with both vinyl acetate and ethyl acrylate were prepared (in benzene at 60°C initiated by t-butyl peroxypivalate) at a variety of M₁/M₂ ratios. The reactivity ratios for the vinyl acetate (M₂) copolymerizations were r₁ = 1.44 and r₂ = 0.039, while for ethyl acrylate copolymerizations r₁ = 0.21 and r₂ = 0.88. The glass transition temperatures were obtained as a function of the M₁/M₂ ratio. The values of T_g for the copolymers fell between those of poly(pentachlorophenyl acrylate) and either poly(vinyl acetate) or poly(ethyl acrylate). A series of bulk copolymers with low pentachlorophenyl acrylate content were studied as biocidal coatings using accelerated growth agar dish tests inoculated with Aspergillus sp., Pseudomonas sp., Alternaria sp., and Aureobasidium pullulans. The copolymers retarded or prevented growth but did not give a zone of inhibition around the coatings. Pentachlorophenol, when added to coating polymers, did exhibit a zone of inhibition due to migration of this biocide into the agar medium.     

Poly(vinyl chloroformate) and derivatives: 2. Copolymerization of vinyl chloroformate and of phenyl vinyl carbonate with vinyl monomers

Vinyl chloroformate and phenyl vinyl carbonate have been copolymerized with vinyl acetate in methylene chloride at 35°C, using dicyclohexylperoxydicarbonate as initiator. The copolymerization parameters obtained show that vinyl chloroformate and vinyl acetate have nearly the same reactivity whereas phenyl vinyl carbonate is slightly less reactive than vinyl acetate.