Ru掺杂SnO2半导体固溶体的电子结构研究

运用基于密度泛函理论的第一性原理方法,建立了SnO₂以及不同比例Ru掺杂的SnO₂超胞模型,在对其进行几何优化后计算了Sn_1-xRu_xO₂(x=0,1/16,1/12,1/8,1/6,1/4,1/2)半导体的电子结构,并讨论了其晶格参数、电荷密度、能带结构和态密度(包括分态密度)等性质。结果表明,掺杂后,晶格参数随掺杂量的增加线性减小,与实验值的偏差在4%以内;掺杂后,在费米能级处可以提供更多的填充电子,使得电子跃迁至导带更容易,固溶体的导电性增强。为Sn_1-xRu_xO₂固溶体电极材料的发展和应用提供了理论基础。     

硫掺杂氧化锡纳米材料的固相合成及其可见光降解百草枯

以十二烷基苯磺酸钠(SDBS)为模板, 采用低温固相反应法合成了硫掺杂二氧化锡(S-SnO₂)纳米粉体材料, 并用XRD、XPS、SEM、UV-Vis、FTIR及HR-TEM等技术对材料进行了表征, 探讨了S掺杂SnO₂纳米材料对百草枯的可见光降解性能, 分析了S掺杂效应的作用机理。结果表明, 采用固相反应法所得SnO₂及S-SnO₂纳米材料的禁带宽度变窄, SDBS对材料的表面结构具有一定的调控作用。S是以S(Ⅳ)和S(Ⅵ)的形式进入SnO₂晶格形成Sn_1-xS_xO₂晶体结构而不是进入SnO₂晶格间隙, Sn-O-S键的弯曲振动峰介于930~980 cm^-1之间。S的掺杂使SnO₂纳米材料表面活性增强, 光催化降解百草枯的活性依次为SnO₂ 2(SDBS) 2 2(SDBS), 2 h内, S-SnO_2(SDBS)样品对除草剂百草枯的光催化活性达95.2%, 其主要原因是S-SnO_2(SDBS)材料表面有更多的羟基和进入SnO₂晶格的S, 有利光生电荷的有效分离。     

Ce1－xNdxO2－δ固溶体的电子顺磁共振谱和阻抗谱的研究

利用溶胶-凝胶方法在800 ℃焙烧10 h后, 合成了固溶体Ce_1－xNd_xO_2－δ (x＝0.05～0.55), X射线衍射(XRD)测试表明固溶体已经形成立方萤石结构; 电子顺磁共振谱(EPR)研究表明在固溶体Ce_1－xNd_xO_2－δ中随着掺杂量x的增大, Ce^3＋离子含量减少, 说明掺杂Nd^3＋离子可以抑制Ce^4＋的还原; 交流阻抗谱的测量表明固溶体Ce_0.9Nd_0.1O_2－d 具有离子导电特性, 600和700 ℃时的电导率分别为4.25×10^－3和1.12×10^－2 S•cm^－1, 活化能为0.68 eV.     

Mg掺杂In2O3-x催化剂光热催化CO2加氢

为提高光热催化CO₂加氢In₂O₃催化剂的催化活性,采用均相水热法制备Mg (OH)₂-In (OH)₃前驱体,通过高温煅烧和H₂-还原处理得到了富含氧空位的Mg掺杂In₂O_3-x(Mg-In₂O_3-x)催化剂。在300℃、常压、可见光照射条件下,CO₂加氢转化为CO的CO₂转化率可达31.20%,CO产生速率为14.22 mmol·g_cat^-1·h^-1,CO选择性为100%。相比于单一In₂O_3-x催化剂,Mg-In₂O_3-x催化剂光热催化CO₂转化率及CO产生速率明显提高,这归因于Mg成功掺杂到In₂O₃晶格中,促进In₂O₃表面氧空位的形成,进而对可见光响应效率大幅提高,并有效减缓光生电子-空穴的复合。     

Mg掺杂In2O3-x催化剂光热催化CO2加氢

为提高光热催化CO₂加氢催化剂In₂O₃的催化活性,采用均相水热法制备Mg(OH)₂-In(OH)₃前驱体,通过高温煅烧和H₂-还原处理得到了富含氧空位的Mg掺杂In₂O_3-x(Mg-In₂O_3-x)催化剂。在300℃、常压、可见光照射条件下,CO₂加氢转化为CO的CO₂转化率可达31.20%,CO产生速率为14.22 mmol·gcat^-1·h^-1,CO选择性为100%。相比于单一In₂O_3-x催化剂,Mg-In₂O_3-x催化剂光热催化CO₂转化率及CO产生速率明显提高,这归因于Mg成功掺杂到In₂O₃形晶格中,促进In₂O₃表面氧空位的形成,进而对可见光响应效率大幅提高,并有效减缓光生电子-空穴的复合。     

溶胶-凝胶法合成Li1-xNaxMn2O4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na⁺离子掺杂的Li_1-xNa_xMn₂O₄(x=0,0.01,0.03,0.05)。X射线衍射图表明Na⁺取代Li⁺进入Li_1-xNa_x Mn₂O₄晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_0.97Na_0.03Mn₂O₄在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn₂O₄从51.2%提升到84.1%。循环伏安测试表明Na⁺离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li_0.97Na_0.03Mn₂O₄仍有79.0 mAh·g^-1的放电容量,高于未掺杂样品的52.1 mAh·g^-1。Na⁺离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn₂O₄的电化学性能,是一种可行的改性方法。     

LixNi0.5Co0.5O2的态密度计算及电化学性能研究

>为获得综合性能更好的锂离子二次电池正极材料, 分析了Co掺杂对Li_xNiO₂电化学性能的影响. 采用密度泛函DFT理论对Li_xNiO₂和Li_xNi_0.5Co_0.5O₂的平均放电电压和态密度进行了计算. 同时, 用共沉淀法制备了Li_xNiO₂和Li_xNi_0.5Co_0.5O₂锂离子二次电池正极材料, 并对其进行了XRD结构分析和恒流充放电测试. 实验和计算结果表明: 随锂离子嵌入正极(电池放电), 电池的电压逐渐降低, 材料的态密度峰向低能量方向移动; 与Li_xNiO₂相比, Li_xNi_0.5Co_0.5O₂的电压平台相对较高(当0.25≤x≤0.5), 而且在Li^＋嵌/脱时, Li_xNi_0.5Co_0.5O₂的结构变化相对较小; Co离子的掺入, 减小了NiO₆八面体的畸变度, 使材料的电化学稳定性得以提高. 在钴掺杂镍酸锂体系中, NiO₆和CoO₆具有相互的稳定作用.     

固体电解质La2-xCaxMo1.7W0.3O9-δ(0≤x≤0.2)的合成、表征及电性能

在氧离子导体La₂Mo_1.7W_0.3O₉的基础上，采用固相法合成了La位掺杂的Ca系列新型氧化物La_2-xCa_xMo_1.7W_0.3O_9-δ(0≤x≤0.2)。通过XRD、Raman和XPS等手段对化合物结构进行表征，交流阻抗谱测试其电性能。结果表明：掺杂离子Ca²⁺的半径小于基质离子La³⁺的半径导致晶格收缩；Ca的掺杂在La₂Mo_1.7W_0.3O₉自身内置氧空位的基础上增加了额外的氧空位，提高了氧离子导体的电导率，550 ℃电导率由0.79 × 10^-4 S·cm^-1 (x=0.0)增加到1.5 × 10^-4 S·cm^-1 (x=0.16，0.2)，电导率增加89.9%。     

室温下制备以{211}晶面为主的Ti1-xVxO2薄膜及其可见光催化性能

以金属Ti和V作为靶材,采用直流反应共溅射技术在室温下制备了以{211}晶面为主的锐钛矿相Ti_1-xV_xO₂薄膜,研究了不同V靶功率对Ti_1-xV_xO₂薄膜的薄膜成分、晶相结构和可见光催化性能的影响。研究表明,Ti_1-xV_xO₂薄膜的晶相结构为锐钛矿相,择优取向为(211),而结晶度受V靶功率的影响。随着V靶功率的增加,薄膜中V元素含量逐渐增加,同时,晶粒和沉积速率也逐渐增加。另外,当V靶功率为150 W时,薄膜的表面粗糙度值有一个最大值。V的掺杂导致薄膜的能带间隙变窄,对光的吸收向可见光区偏移,从而有效地改善了薄膜的可见光催化能力。当V靶功率为150 W时,Ti_1-xV_xO₂薄膜的能带间隙值为 2.82 eV,其在2 h的可见光照射下分解了80%的RhB染料。这被归结于能带间隙窄,高能晶面{211}和结晶度高的共同作用。     

NbS2-xSex的制备、表征及其摩擦学性能

本文采用固相反应合成了NbS_2-xSe_x纳米材料。并分别采用XRD、SEM、TEM、HRTEM进行了结构、形貌和成分的分析表征。系统研究了合成温度、保温时间及不同掺杂量对产物晶型和形貌演化的影响及规律性。结果表明Se的掺杂使NbS_2-xSe_x的形貌由纳米带(板)转变为纳米片,衍射峰明显宽化,峰强变弱,晶粒细化。且掺杂量、保温温度及时间对产物的形貌影响较大;在750℃下保温2h得到的掺杂5at%Se的NbS_1.9Se_0.1形貌良好。将NbS_2-xSe_x作为液体石蜡油的添加剂的UMT-2摩擦学实验结果表明掺杂后的NbS_2-xSe_x具有优异的摩擦性能,其中掺杂5at%的Se在750℃下保温2h的NbS_1.9Se_0.1摩擦性能最佳,同时对其摩擦机理进行了解释。     

Synthesis and electrochemical properties of LiNi0.9-xCo0.1SnxO2 as cathode materials for lithium secondary batteries

LiNi_0.9-x Co_0.1Sn _x O₂ (x = 0.00, 0.02, and 0.03) were synthesized via the rheological phase reaction method and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical tests. The sample of LiNi_0.9-x Co_0.1Sn _x O₂ (x = 0.02) not only shows good cycle performance but also exhibits an excellent discharge capacity of 188 mAh/g in the first cycle at a current density of 100 mA/g in the voltage range of 3.0–4.3 V. The tin doping results in reducing the resistance and increasing conductivity of LiNi_0.9-x Co_0.1Sn _x O₂. This composite oxide is promising as cathode material for lithium-ion battery.     

Darstellung,Eigenschaften und Phasenbeziehungen von Ru3Sn15O14

Preparation, Properties, and Phase Relations of Ru₃Sn₁₅O₁₄ Coexistence relations in the system Ru/Sn/O have been investigated by X‐ray measurements of powder mixtures annealed in the region of 1173–1273 K. Thermodynamic data of Ru₂Sn₃, Ru₃Sn₇, and Ru₃Sn₁₅O₁₄ were obtained by EMF measurements. Phase diagrams calculated with these data are in good agreement with experimental results. Only one phase, Ru₃Sn₁₅O₁₄, exists in the ternary system between 973 and 1273 K. Red translucend single crystals were obtained from a tin melt. Polycrystalline powder was prepared by solid state reaction of a mixture of Ru₃Sn₇, SnO₂, and Sn with molar ratio 1:7:1 at 1173 K. Ru₃Sn₁₅O₁₄ is a p‐type semiconductor, E_A = 0.50(5) eV, as conductivity and thermopower measurements show. Mössbauer investigations confirm the existence of three different tin surroundings.     

Preparation and magnetic properties of Fe-Nb co-doped SnO2

Fe³⁺-Nb⁵⁺ co-doped SnO₂ was prepared at 1200 °C by a simple chemical co-precipitation method. The Sn_1−2xFe_xNb_xO₂ solid solutions kept cassiterite structure in the range of 0<x?0.33, and their cell parameters decrease with increasing x. While x=0.40, a second phase with orthorhombic FeNbO₄ structure co-exists with the cassiterite phase, and the second phase becomes dominant while x?0.45. The magnetic measurements indicated that low doping ratio sample (x=0.03) exhibits paramagnetic behavior. A paramagnetic-to-antiferromagnetic phase transition was observed for the samples with higher doping ratio (x?0.15).     

固溶体Bi_2Mo_(1-x)W_xO_6的水热合成及光催化性能

采用水热法,在较低温度下合成了系列Bi2Mo1-xWxO6固溶体。结果表明,W的替代抑制了固溶体的晶粒生长,导致了较小的晶粒尺寸。随着x的增加,红外光谱中840cm-1处M-O键的振动频率νM-O有规律地向低频率方向移动,表明Mo6+离子逐步被W6+替代,生成了无限互溶的固溶体。光吸收性能研究表明,随着W6+逐步替代Mo6+,带隙出现了先降后升的趋势,x=0.4时带隙最小。而固溶体的光催化性能随着x的增加,出现了先增后减的趋势,x=0.4时光催化活性最高。此外,含W样品的光催化活性高于Bi2MoO6。这与固溶体的带隙、带结构和晶粒尺寸变化有关。     

Electronic structures of superconductors YBa2Cu3−x M x O y (M=Sn,Ni)

Based on the EHMO approach, the energy band structures for superconductors YBa₂Cu_3–x Sn _x O _y (y>7) and YBa₂Cu_3–x Ni _x O_y (y<7) were calulated in the present paper. The influence of the cation doping at the Cu site in the unit cell and the oxygen content on their electronic structures was studied. The results showed that the cation doping at the Cu site resulted in the great decreases in the bandwidths of the broad anisotropic Cu-O bands and the densities of states. In YBa₂Cu_3–x Sn _x O _y , however, these decreases are compensated by the increase in the oxygen content caused by the Sn-doping, which results in a small change in the total densities of states. For YBa₂Cu_3–x Ni _x O _y , the effect of the doping on its electronic structures in dominant. The Ni-doping, therefore, results in a great change in the electronic structures. In addition, the study on the projected densities of states of the Ni-doped system revealed that the 2D Cu-O planes in the Y-Ba-Cu-O system played a dominant role in superconductivity.     

Effect of voltage on the AC conductivity of Li4SiO4

The photoelectrochemical behaviour of a Ru-doped TiO₂ Crystal electrode of composition Ti_0.97Ru_0.03O₂ in contact with aqueous electrolytes has been investigated. The substitution of Ru⁴⁺ for Ti⁴⁺ in the TiO₂ lattice produces two main effects; (i) sensitization to visible light; (ii) reduction of the overpotential for O₂ evolution, both in the dark and under illumination. Ru⁴⁺ eneryg levels constitute a narrow cationic band between the O2_p valence band and the Ti3d conduction band, Ru⁴⁺ → Ti⁴⁺ electronic transitions being responsible for the subbandagap photoresponse. Besides Ru⁴⁺ ions at the semiconductor surface are easily oxidized under positive polarization of the electrode: the surface becomes charged positively and the Fermi level is pinned, which facilitates the transfer of charge from the filled levels of water molecules to the semiconductor conduction band, leading to O₂ evolution. The transient photocurrent-time behaviour observed, both under bandgap and subbandgap illumination, is compared with that of undoped TiO₂ and analyzed in terms of charge transfer at the semiconductor—electrolyte interface.     

溶胶-凝胶法合成Li_(1-x)Na_xMn_2O_4及其作为水系锂离子电池正极材料的电化学性能

用溶胶凝胶法合成了Na+离子掺杂的Li_(1-x)Na_xMn_2O_4(x=0,0.01,0.03,0.05)。X射线衍射图表明Na+取代Li+进入Li_(1-x)Na_xMn_2O_4晶格中,扫描电镜图看出产物是粒径为100~300 nm的颗粒。恒流充放电测试结果表明,Li_(0.97)Na_(0.03)Mn_2O_4在2C倍率下循环100圈后放电容量保持率比未掺杂的LiMn_2O_4从51.2%提升到84.1%。循环伏安测试表明Na+离子掺杂降低了材料极化且增大了锂离子扩散系数。10C倍率下Li0.97Na0.03Mn2O4仍有79.0 m Ah·g-1的放电容量,高于未掺杂样品的52.1 m Ah·g~(-1)。Na+离子掺杂可以稳定材料结构并提高锂离子扩散系数,从而提高LiMn_2O_4的电化学性能,是一种可行的改性方法。     

Synthesis and optical absorption property of the Zn2TixSn1−xO4 (0?x?1) solid solutions

Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions with an inverse spinel structure (Fd3m) were synthesized by solid-state reactions at 1300°C of the stoichiometric mixtures of ZnO, TiO₂ and SnO₂. X-ray diffraction, thermogravimetric and differential thermal analyses, scanning electron microscopy, transmission electron microscopy and BET specific surface area measurements were used to gain insights into the solid-state reactions and phase transformation of the system. Optical absorption property of the Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions was studied with the ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). The Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions showed optical absorptions of the semiconductors in the near ultraviolet region; the adsorption band shifts with the composition of the solid solution.