采动裂隙岩体压剪渗透规律试验研究

根据采动过程中裂隙岩体的应力变化,用法向载荷、剪切载荷和渗透水压分别模拟开采过程中采场的水平应力、垂向应力和水头压力,应用JAM-600型剪切-渗流耦合试验系统对裂隙岩体进行压剪-渗流藕合试验,探讨在恒定法向荷载(CNL)和法向刚度(CNS)条件下,裂隙岩体的法向载荷、裂隙粗糙度与渗透水压对试样的位移、应力和渗流性的影响规律,分析剪切位移大小和岩体裂隙的剪胀特性对裂隙岩体的剪切应力、法向位移、节理水力开度及渗透率影响规律。研究表明:剪切应力和水头压力对裂隙水力开度起促进作用,水平地应力对水力开度变化起抑制作用。随着剪切位移变化,水力开度可分为变小或持平、增大、稳定3个阶段。裂隙表面粗糙度越大,裂隙岩体的刚度越小,则水力开度最终稳定值越大。由于裂隙岩体的剪胀作用渗透率先变小后增大,剪切位移增大,渗透率增大;法向荷载增大,试件的渗透率越小;裂隙表面越粗糙,其渗透率越大,其研究结果可为岩体透水通道形成时的孕育、萌生和爆发的导渗灾变演化过程提供理论基础。     

单裂隙粗砂岩渗流规律试验研究

以石嘴山矿西翼采区为研究背景,通过三轴应力作用下岩石单裂隙渗流试验、裂隙开度与有效压力关系试验和大尺度岩石表面粗糙度量测试验,结合渗流力学基本理论,揭示了三维应力下单裂隙粗砂岩渗流规律,建立了有效压力、裂隙开度与渗透系数的关系式,以期丰富裂隙岩体渗流的理论研究。     

三维应力作用下岩体单个裂隙的渗流特性分析

天然岩体中存在着大量的孔隙和裂隙,这些缺陷不仅改变了岩体的力学性质,也严重影响了岩体的渗流特性。在对现有裂隙岩体渗流特性研究成果进行分析的基础上,讨论了岩体单个裂隙的力学性质和渗流对单个裂隙岩体产生的力学作用,研究了岩体单裂隙渗透系数与岩体三维应力的关系,考虑了裂隙粗糙度对渗流的影响以及不同方向应力对渗透性影响的差异,分析了单个裂隙岩体在三向应力作用下的渗流特征,得出了裂隙所受三维应力与渗透系数关系式,认为垂直于裂隙面的应力对岩体渗透性起主导作用,岩体渗透系数随垂直裂隙面应力的增加而迅速减小。通过与渗流规律试验结果对比分析,证明了所得单个裂隙岩体渗透系数表达式的正确性。     

多场耦合作用下岩体裂隙扩展演化关键问题研究

裂隙岩体热-水-应力（THM）耦合是目前研究的热点和难点。首先总结了裂隙岩体多场耦合的机制、模型、方法及研究内容,并通过分析裂隙对THM耦合的重要控制作用,提出了在THM耦合中考虑裂隙网络扩展演化及模拟的关键问题,同时指出了研究的3个关键点：（1）建立考虑裂隙网络演化的耦合模型;（2）裂隙扩展的数值模拟方法;（3）THM耦合及岩体变形、失稳全过程的数值模拟算法。随后通过对模拟多场耦合和裂隙扩展数值方法的归类比较,重点论述了目前适用于模拟多场耦合下裂隙扩展模拟的各种数值方法（包括有限单元法、无单元法、单位分解法、离散单元法、岩石破裂过程分析方法和数值流形方法）的优缺点,并通过对比研究,推荐采用数值流形方法（NMM）来实现对关键问题的模拟研究。最后,对研究思路和难点进行了初步探讨。     

裂隙岩体渗流-应力耦合等效渗流阻模型

针对含区域主干裂隙岩体在应力作用下的渗透特性进行了研究。运用单裂隙平行板渗流理论、弹性力学方法,结合模拟电路知识,提出等效渗流阻的概念。在分析裂隙岩体区域中主干裂隙系统几何构造的基础上,建立了基于等效渗流阻的- 渗流-应力耦合模型,得到了裂隙岩体等效渗流阻、渗透率与应力之间的关系,从而为研究含区域主干裂隙岩体的应力-渗流耦合规律提供了方便。结合一个基于等效渗流阻模型的算例,考察了含“人”字形组合裂隙试样的渗透特性。经进一步细化后,该模型可用于分析地应力作用下的含区域主干裂隙岩体渗流演化规律。     

裂隙岩体渗流应力耦合研究综述

系统综述了裂隙岩体渗流应力耦合的研究情况。阐明了单裂隙面的各种经验公式、间接公式及其适用条件,分析了裂隙岩体渗流应力耦合模型优缺点及目前工程应用情况。     

基于PIV技术的贯通单裂隙岩体压-剪破坏特征试验

基于PIV技术,采用相似材料预制贯通单裂隙岩体试件并开展压-剪试验,探究了裂隙开度对贯通单裂隙试件的强度、变形及破坏过程的影响.结果表明:(1)试件发生初始断裂时不同裂隙开度试验组应力均明显下降,且随着开度的增大裂隙岩体胶结部位塑性变形增强,岩体试件的特征应力值减小;(2)裂隙开度影响到裂隙和胶结部位变形在试件总变形中...     

裂隙岩体渗流与应力耦合的试验研究

通过对较大尺寸的裂隙岩体试块进行不同侧压力和加载条件下的渗流试验结果研究，分析了裂隙岩体渗流与应力的耦合机理，得出了不同应力条件下裂隙岩体渗流量与应力成四次方的关系。并且得出并非压应力都引起裂隙岩体的渗流量减小，当裂隙岩体受平行于裂隙面方向的单向压应力时，渗流量随着压应力的增加而增加。     

裂隙岩体非饱和渗流的分形模型

基于毛细吸持理论和Sierpinski空间的假定,建立了用分维数表示的毛细压力-有效饱和度及毛细压力-相对渗透系数关系的裂隙岩体非饱和渗流分形模型。根据Monte-Carlo模拟技术由平硐资料生成三维裂隙网络,利用盒维数方法计算裂隙岩体体积分维数。探讨了分维数与裂隙渗透率的关系。结合糯扎渡水利工程实例,将模型计算结果与Brook-Corey模型对比,结果表明相对渗透率主要受最大裂隙开度的影响,当裂隙开度范围不大时,分形模型可较好描述岩体裂隙的毛细压力与有效饱和度的关系。当裂隙开度范围较大时, ,忽略最大裂隙开度,模型可以等价于Brook-Corey模型。     

考虑卸荷作用的裂隙岩体渗流应力耦合研究

大量试验证明,裂隙岩体在加载和卸荷的条件下其渗流与应力特性是不完全相同的。近年来,加载条件下的裂隙岩体渗流应力耦合研究得到了长足的发展,但卸荷作用下的水岩耦合分析还处于初始阶段。基于现有裂隙变形曲线的研究结果,建立了渗透系数与卸荷应力、应变间的本构关系,在此基础上,根据算例分析了各种工况下的渗流和应力特征,其计算结果表明,考虑卸荷后应力场的改变增加了临近坡面的岩体渗透系数,降低了地下水浸润线,增加了边坡的稳定性;考虑渗流后,边坡的位移场和应力场有较大改变,但考虑耦合后位移和应力分布和大小与不耦合时的相差不大;边坡开挖后应力场改变对渗流的影响远大于渗流对位移、应力等的影响。     

岩体裂隙饱和/非饱和渗流机理初步研究

基于裂隙局部开度为平行板模型的假定,按一定分布抽样生成裂隙面上开度随机数,并分别对单裂隙饱和及非饱和渗流进行了数值模拟.裂隙饱和及非饱和渗流在渗流机理上都是由于水势差引起的,只不过在非饱和渗流情形下,湿润相水压力小于非湿润相空气的压力.饱和渗流时,水流主要集中在大开度,即“沟槽”中;而非饱和渗流时,水流运动多发生在小开度,即“狭缝”中.     

Discrete element model for crack propagation in brittle materials

We propose a discrete element model for brittle rupture. The material consists of a bidimensional set of closed‐packed particles in contact. We explore the isotropic elastic behavior of this regular structure to derive a rupture criterion compatible to continuum mechanics. We introduce a classical criterion of mixed mode crack propagation based on the value of the stress intensity factors, obtained by the analysis of two adjacent contacts near a crack tip. Hence, the toughness becomes a direct parameter of the model, without any calibration procedure. We verify the consistency of the formulation as well as its convergence by comparison with theoretical solutions of tensile cracks, a pre‐cracked beam, and an inclined crack under biaxial stress. Copyright © 2015 John Wiley & Sons, Ltd.     

Spatial averaging of hydraulic conductivity under radial flow conditions

Steady-state radial flow in three-dimensional heterogeneous media is investigated using a geostatistical approach. The goal of the study is to develop a model of the relationship between corescale hydraulic conductivities measured at the wellbore and the conductivity of the surrounding drainage region as measured by a larger scale flow experiment such as a pump test. Conductivity at the point or core-scale is modeled as a stationary and multivariate lognormal spatial random function. Conductivity of the drainage region is obtained by a weighted nonlinear spatial average over the point-scale values within. This empirical spatial averaging process is shown to yield excellent approximations of true effective drainage region conductivities calculated using a numerical flow model. The geostatistical model for point-scale conductivity and the spatial averaging process are used to determine the first and second order ensemble moments of drainage region conductivity. In particular, an expression is derived for the conditional expectation of drainage region conductivity given point-scale values measured at the wellbore. The results are illustrated in a case study of a well from a sandstone oil reservoir where both core and transient-test conductivity data from the same interval are available for comparison.     

预制横缝条件下水力裂缝的起裂和扩展

针对高角度天然裂缝发育地层中的水平井水力压裂问题,开展了水力裂缝自天然裂缝处起裂扩展的理论和试验研究。尝试将天然裂缝简化为与井筒轴线垂直的横向裂缝,基于线弹性断裂力学理论和最大拉应力准则,给出了水力裂缝起裂压力和扩展过程中应力强度因子的计算方法。利用预制横缝模拟高角度天然裂缝,开展了室内水力压裂试验,对水力裂缝的扩展形态和起裂压力进行了研究。理论计算表明,（1）水力裂缝自预制横缝端部起裂后,扩展距离超过1倍的预制横缝端部半径时可将预制横缝和水力裂缝合并起来,整体视作一条横向裂缝来计算应力强度因子;（2）水力裂缝尖端距井壁处的距离大于4倍的井筒半径时,应力强度因子的计算可忽略井筒的影响,近似采用硬币形裂缝的计算公式。试验研究发现,（1）水力裂缝在预制横缝端部起裂并扩展,形成与井筒轴线垂直的横向裂缝,裂缝的扩展呈现出Ⅰ型断裂的特点,形态近似呈圆形,未发现与井筒轴线平行的纵向裂缝的起裂和扩展;（2）排量对破裂净压力和起裂净压力有重要影响,大排量会导致较高的破裂净压力和起裂净压力,在大、小两种排量下起裂净压力的离散性均较小,计算得到的KⅠ临界断裂值的离散性也较小。研究结果可为改善裂缝发育储层的近井裂缝形态提供指导,也可为煤矿开采中预制横向切槽的水力压裂设计提供参考。     

A relationship between tensile strength and loading stress governing the onset of mode I crack propagation obtained via numerical investigations using a bonded particle model

Numerical models based on the discrete element method are used to study the fracturing process in brittle rock‐like materials under direct and indirect tension. The results demonstrate the capacity of the model to capture the essential characteristics of fracture including the onset of crack propagation, stable and unstable crack growth, arrest and reinitiation of fracturing, and crack branching. Simulations of Brazilian indirect tension tests serve to calibrate the numerical model, relating macroscopic tensile strength of specimens to their micromechanical breakage parameters. A second suite of simulations reveals a linear relationship between the tensile strength of specimens and the loading stress for which mode I tensile crack propagation ensues. Based on these results, a crack initiation criterion for brittle materials is proposed, prescribing the stressing conditions required to induce tensile failure. Such a criterion, if broadly applicable, provides a practical means to rapidly assess the failure potential of brittle materials under tensile loads.     

水-岩化学作用等效裂纹扩展细观力学模型

从化学腐蚀下岩石细观结构的变化出发,研究水化学溶液对岩石中裂纹的腐蚀作用。运用地球化学矿物-水反应的溶解动力学,考查水-岩反应化学溶液中不同时间段离子浓度的变化,从理论上探讨化学腐蚀下等效裂纹扩展的定量化分析方法。通过质量守恒定律计算出裂纹在迹长及隙宽方向的变化,将水化腐蚀等效成有效裂纹长度,建立了水-岩化学作用下等效裂纹扩展的计算公式并计算应力强度因子。通过对砂岩的研究结果表明,水-岩化学作用对岩石裂纹的扩展有显著影响,并且具有时间效应。同时,水化学溶液的离子浓度及pH值大小对裂纹的扩展存在影响,其中pH值的变化对岩石的断裂力学效应更加显著。当溶液的酸性越强或碱性越强,腐蚀越大,裂纹扩展越快;pH值为中性时,腐蚀作用得到较大缓解,裂纹发展缓慢。为定量研究裂隙岩体在水岩化学作用下的细观机理提供了一种新的思路。     

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.     

爆炸应力波作用下缺陷介质裂纹扩展的动态分析

采用透射式焦散线测试系统,进行爆炸应力波作用下缺陷介质裂纹扩展试验,研究了含与炮孔共线的预制裂隙介质裂纹扩展速度、加速度、裂纹尖端动态应力强度因子和动态能量释放率的变化规律以及它们之间的变化关系。试验结果表明,在爆炸应力波作用下裂隙两端产生了两条翼裂纹A、B,翼裂纹A的长度较翼裂纹B长,两条翼裂纹向相反的方向扩展;在翼裂纹扩展过程中,存在着加速与减速的过程,扩展速度瞬间达到峰值,其后逐渐振荡下降;动态应力强度因子也呈现瞬间达最大值到逐渐减小连续振荡变化的趋势,动态应力强度因子 > ;翼裂纹尖端的动态能量释放率对裂纹扩展具有驱动作用。     

Evolution of fluid pressure and fracture propagation during contact metamorphism

Abstract Rock fracture enhances permeability and provides pathways through which fluids migrate. During contact metamorphism, fluids contained in isolated pores and fractures expand in response to temperature increases caused by the dissipation of heat from magmas. Heat transport calculations and thermomechanical properties of water-rich fluids demonstrate (1) that thermal energy is a viable mechanism to produce and maintain pore fluid pressure (P_f) in a contact metamorphic aureole; (2) that the magnitude of P_f generated is sufficient to propagate fractures during the prograde thermal history (cause hydrofracture) and enhance permeability; and (3) that P_f-driven fracture propagation is episodic with time-scales ranging from years to thousands of years. Because P_f dissipation is orders of magnitude faster than P, _f buildup, P_f oscillations and cyclical behaviour are generated as thermal heating continues. The P_f cycle amplitude depends on the initial fracture length, geometry and the rock's resistance to failure whereas the frequency of fracture depends on the rate of heating. Consequently, oscillation frequency also varies spatially with distance from the heat source. Time series of fluid pressures caused by this process suggest that cyclical fracture events are restricted to an early time period of the prograde thermal event near the intrusive contact. In the far field, however, individual fracture events have a lower frequency but continue to occur over a longer time interval. Numerous fracture cycles are possible within a single thermal event. This provides a provisional explanation for multiple generations of veins observed in outcrop. P _f cycling and oscillations may explain several petrological features. If pore fluids are trapped at various positions along a pressure cycle, the large amplitude of P_f variations for small fractures may account for different pressures recorded by fluid inclusions analysed from a single sample. P_f oscillations, during a single thermal episode, also drive chemical reactions which can produce complex mineral textures and assemblages for discontinuous reactions and/or zoning patterns for continuous reactions. These can mimic polymetamorphic or disequilibrium features. Temporal aspects of fracture propagation and permeability enhancement also constrain the likely timing of fluid flow and fluid-mineral interactions. These data suggest that fluid flow and fluid-mineral reactions are likely to be restricted to an early period in the prograde thermal history, characterized by high P_f coincident with relatively high temperatures, fracture propagation and consequent increases in permeability. This early prograde hydration event is followed by diffusional peak metamorphic reactions. This relationship is evident in the complex mineralogical textures common in some metamorphosed rocks.     

Investigation of hydraulic fracturing operation and fracture propagation simulation in reservoir rock

For many decades most oil wells in Iran have produced using their natural flow potential and haven’t needed to be fractured. As time goes by, the reservoir pressure depletes and the need for hydraulic fracturing as a stimulation practice arises. Nonetheless there is no record of successful hydraulic fracturing in Iran.

The Bangestan reservoir with a suitable amount of oil in place and good rock reservoirs, has been selected for the present research work. In this work, the in situ stress profile was calculated by using the available petrophysical data. This is achieved by using poroelastic theory for the stresses, and the Mohr–Coulomb criterion to predict failure. The model leads to easily computed expressions for calculating the pressure required to maintain hydraulic fracturing. Then the appropriate depth for treatment was determined. The results indicate that Ilam and Sarvak formations could be good candidates for hydraulic fracturing. Then, for two layers, a hydraulic fracture was designed and the production was predicted and the Net Present Value (NPV) resulting from the fracture of both layers was investigated.