Structural and chemical promoter effects of alkali (earth) and cerium oxides in CO oxidation on supported gold

Nanostructured Au/Al₂O₃ catalysts prepared by deposition–precipitation with urea were characterized by X-ray diffraction (XRD) and high-resolution transmission electron microscopy (HRTEM) and tested for low temperature CO oxidation. The paper is focused on the effect of two different kinds of additives on the structure and reactivity of Au/Al₂O₃ for CO oxidation: (1) alkali (earth) metal oxides and (2) ceria. The structural properties of nanosized Au particles are drastically affected by the presence of additives. The main role of the alkali (earth) metal oxides is to stabilize the small Au particles against sintering, such that when BaO is added to Au/Al₂O₃, full CO conversion is already achieved at room temperature. For this reaction ceria addition does not result in a higher activity. However, when both BaO and CeO_x are added to Au/Al₂O₃, the catalytic performance of the multicomponent catalyst resembles that of Au/BaO/Al₂O₃.     

Total oxidation of propene and propane over gold–copper oxide on alumina catalysts: Comparison with Pt/Al2O3

Oxidation of propene and propane to CO₂ and H₂O has been studied over Au/Al₂O₃ and two different Au/CuO/Al₂O₃ (4 wt.% Au and 7.4 wt.% Au) catalysts and compared with the catalytic behaviour of Au/Co₃O₄/Al₂O₃ (4.1 wt.% Au) and Pt/Al₂O₃ (4.8 wt.% Pt) catalysts. The various characterization techniques employed (XRD, HRTEM, TPR and DR-UV–vis) revealed the presence of metallic gold, along with a highly dispersed CuO (6 wt.% CuO), or more crystalline CuO phase (12 wt.% CuO).

A higher CuO loading does not significantly influence the catalytic performance of the catalyst in propene oxidation, the gold loading appears to be more important. Moreover, it was found that 7.4Au/CuO/Al₂O₃ is almost as active as Pt/Al₂O₃, whereas Au/Co₃O₄/Al₂O₃ performs less than any of the CuO-containing gold-based catalysts.

The light-off temperature for C₃H₈ oxidation is significantly higher than for C₃H₆. For this reaction the particle size effect appears to prevail over the effect of gold loading. The most active catalysts are 4Au/CuO/Al₂O₃ (gold particles less than 3 nm) and 4Au/Co₃O₄/Al₂O₃ (gold particles less than 5 nm).     

A comparative study of the water-gas shift activity of Pt catalysts supported on single (MOx) and composite (MOx/Al2O3, MOx/TiO2) metal oxide carriers

The water-gas shift (WGS) activity of platinum catalysts dispersed on a variety of single metal oxides as well as on composite MO_x/Al₂O₃ and MO_x/TiO₂ supports (M = Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Y, Zr, La, Ce, Nd, Sm, Eu, Gd, Ho, Er, Tm) has been investigated in the temperature range of 150–500 °C, using a feed composition consisting of 3% CO an 10% H₂O. For Pt catalysts supported on single metal oxides, it has been found that both the apparent activation energy of the reaction and the intrinsic rate depend strongly on the nature of the support. In particular, specific activity of Pt at 250 °C is 1–2 orders of magnitude higher when supported on “reducible” compared to “irreducible” metal oxides. For composite Pt/MO_x/Al₂O₃ and Pt/MO_x/TiO₂ catalysts, it is shown that the presence of MO_x results in a shift of the CO conversion curve toward lower reaction temperatures, compared to that obtained for Pt/Al₂O₃ or Pt/TiO₂, respectively. The specific reaction rate is in most cases higher for composite catalysts and varies in a manner which depends on the nature, loading, and primary crystallite size of dispersed MO_x. Results are explained by considering that reducibility of small oxide particles increases with decreasing crystallite size, thereby resulting in enhanced WGS activity. Therefore, evidence is provided that the metal oxide support is directly involved in the WGS reaction mechanism and determines to a significant extent the catalytic performance of supported noble metal catalysts. Results of catalytic performance tests obtained under realistic feed composition, consisting of 3% CO, 10% H₂O, 20% H₂ and 6% CO₂, showed that certain composite Pt/MO_x/Al₂O₃ and Pt/MO_x/TiO₂ catalysts are promising candidates for the development of active WGS catalysts suitable for fuel cell applications.     

Selective catalytic reduction of NO by C3H8 over CoOx/Al2O3: An investigation of structure–activity relationships

A series of CoO_x/Al₂O₃ catalysts was prepared, characterized, and applied for the selective catalytic reduction (SCR) of NO by C₃H₈. The results of XRD, UV–vis, IR, Far-IR and ESR characterizations of the catalysts suggest that the predominant oxidation state of cobalt species is +2 for the catalysts with low cobalt loading (≤2 mol%) and for the catalysts with 4 mol% cobalt loading prepared by sol–gel and co-precipitation. Co₃O₄ crystallites or agglomerates are the predominant species in the catalysts with high cobalt loading prepared by incipient wetness impregnation and solid dispersion. An optimized CoO_x/Al₂O₃ catalyst shows high activity in SCR of NO by C₃H₈ (100% conversion of NO at 723 K, GHSV: 10,000 h⁻¹). The activity of the selective catalytic reduction of NO by C₃H₈ increases with the increase of cobalt–alumina interactions in the catalysts. The influences of cobalt loading and catalyst preparation method on the catalytic performance suggest that tiny CoAl₂O₄ crystallites highly dispersed on alumina are responsible for the efficient catalytic reduction of NO, whereas Co₃O₄ crystallites catalyze the combustion of C₃H₈ only.     

CO, H2 or C3H8 assisted catalytic combustion of methane over supported LaMnO3 monoliths

The effect of the addition of a second fuel such as CO, C₃H₈ or H₂ on the catalytic combustion of methane was investigated over ceramic monoliths coated with LaMnO₃/La-γAl₂O₃ catalyst. Results of autothermal ignition of different binary fuel mixtures characterised by the same overall heating value show that the presence of a more reactive compound reduces the minimum pre-heating temperature necessary to burn methane. The effect is more pronounced for the addition of CO and very similar for C₃H₈ and H₂. Order of reactivity of the different fuels established in isothermal activity measurements was: CO>H₂≥C₃H₈>CH₄. Under autothermal conditions, nearly complete methane conversion is obtained with catalyst temperatures around 800 °C mainly through heterogeneous reactions, with about 60–70 ppm of unburned CH₄ when pure methane or CO/CH₄ mixtures are used. For H₂/CH₄ and C₃H₈/CH₄ mixtures, emissions of unburned methane are lower, probably due to the proceeding of CH₄ homogeneous oxidation promoted by H and OH radicals generated by propane and hydrogen pyrolysis at such relatively high temperatures.

Finally, a steady state multiplicity is found by decreasing the pre-heating temperature from the ignited state. This occurrence can be successfully employed to pilot the catalytic ignition of methane at temperatures close to compressor discharge or easily achieved in regenerative burners.     

Effect of hydrogen on reaction intermediates in the selective catalytic reduction of NOx by C3H6

Selective catalytic reduction of NO_x by C₃H₆ in the presence of H₂ over Ag/Al₂O₃ was investigated using in situ DRIFTS and GC–MS measurements. The addition of H₂ promoted the partial oxidation of C₃H₆ to enolic species, the formation of –NCO and the reactions of enolic species and –NCO with NO_x on Ag/Al₂O₃ surface at low temperatures. Based on the results, we proposed reaction mechanism to explain the promotional effect of H₂ on the SCR of NO_x by C₃H₆ over Ag/Al₂O₃ catalyst.     

The reduction phase in NOx storage catalysis: Effect of type of precious metal and reducing agent

The effect of different reducing agents (H₂, CO, C₃H₆ and C₃H₈) on the reduction of stored NO_x over PM/BaO/Al₂O₃ catalysts (PM = Pt, Pd or Rh) at 350, 250 and 150 °C was studied by the use of both NO₂-TPD and transient reactor experiments. With the aim of comparing the different reducing agents and precious metals, constant molar reduction capacity was used during the reduction period for samples with the same molar amount of precious metal. The results reveal that H₂ and CO have a relatively high NO_x reduction efficiency compared to C₃H₆ and especially C₃H₈ that does not show any NO_x reduction ability except at 350 °C over Pd/BaO/Al₂O₃. The type of precious metals affects the NO_x storage-reduction properties, where the Pd/BaO/Al₂O₃ catalyst shows both a high storage and a high reduction ability. The Rh/BaO/Al₂O₃ catalyst shows a high reduction ability but a relatively low NO_x storage capacity.     

A comparative study of Ag/Al2O3 and Cu/Al2O3 catalysts for the selective catalytic reduction of NO by C3H6

The selective catalytic reduction (SCR) of NO by C₃H₆ in excess oxygen was evaluated and compared over Ag/Al₂O₃ and Cu/Al₂O₃ catalysts. Ag/Al₂O₃ showed a high activity for NO reduction. However, Cu/Al₂O₃ showed a high activity for C₃H₆ oxidation. The partial oxidation of C₃H₆ gave surface enolic species and acetate species on the Ag/Al₂O₃, but only an acetate species was clearly observed on the Cu/Al₂O₃. The enolic species is a more active intermediate towards NO + O₂ to yield—NCO species than the acetate species on the Ag/Al₂O₃ catalyst. The Ag and Cu metal loadings and phase changes on Al₂O₃ support can affect the activity and selectivity of Ag/Al₂O₃ and Cu/Al₂O₃ catalysts, but the formation of enolic species is the main reason why the activity of the Ag/Al₂O₃ catalyst for NO reduction is higher than that of the Cu/Al₂O₃ catalyst.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Catalytic oxidation of VOCs on Au/Ce-Ti-O

Ce_xTi_1−xO₂ oxides have been synthesised by sol–gel method with x varying from 0 to 0.3 and characterised by XRD and TPR. The structure of oxides changes with the Ce/Ti molar ratio. The presence of ceria in Ce-Ti oxides inhibits the phase transition from anatase to rutile. When x = 0.3 (Ce_0.3Ti_0.7O₂ sample), the solid presents an amorphous state. The TPR results indicate that the presence of Ti enhances the reducibility of cerium oxide species. Catalytic oxidation of propene is investigated on Ce-Ti oxides and the better conversion is obtained with Ce_0.3Ti_0.7O₂ but the CO₂ selectivity reaches 63% at 400 °C. Gold is then deposited on theses oxides to improve the catalytic activity. On the basis of characterisation data (H₂ TPR), it has been suggested that gold influences the reduction of the Ce-Ti oxide support and the catalytic activity to the propene oxidation. Thus, Au/Ce-Ti-O system catalysts are promising catalysts for propene oxidation.     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

An evolutionary approach in the combinatorial selection and optimization of catalytic materials

A methodical basis of the evolutionary method for selection and optimization of heterogeneous catalytic materials was developed. For validation, the oxidative dehydrogenation of propane was used as a model reaction. Various oxides (V₂O₅, MoO₃, MnO₂, Fe₂O₃, GaO, MgO, B₂O₃, La₂O₃) were chosen as primary components for the generation of catalytic materials. The first generation consisting of 56 catalytic materials was created by combination of the primary components in a stochastic manner. The materials of each preceding generation were selected based on the catalytic results obtained and subjected to an evolutionary procedure applying mutation and crossover operators to create further generations of catalytic materials of different qualitative and quantitative compositions. For illustration, four generations were created with a total number of tested catalytic materials of 224. As a result of the preliminary optimization procedure an increase in the propene yield was achieved with increasing number of generations; the results can be certainly improved by screening further generations of catalytic materials. Under standard conditions used for testing (T=500°C, C₃H₈/O₂=3, p(C₃H₈)=30 Pa), the highest C₃H₆ yield amounted to 9.0% (S=57.4%) in the 3rd generation on V_0.22Mg_0.47Mo_0.11Ga_0.20O_x.     

Oxidation of carbon black over various Pt/MOx/SiC catalysts

Catalytic activities of various Pt/MO_x/SiC systems for carbon oxidation under simulated diesel exhaust gas were investigated in temperature-programmed reactions. When Pt/MO_x (MO_x=TiO₂, ZrO₂, Al₂O₃) was loaded onto silicon carbide (SiC), the oxidation activities became higher than those of Pt/MO_x alone or other Pt/MO_x/SiC systems (MO_x=Ta₂O₅, WO₃, Nb₂O₅, SnO₂, SiO₂, CeO₂, MoO₃, V₂O₅). Among them, Pt/TiO₂/SiC exhibited the highest activity. We discuss the activity of MO_x=TiO₂, ZrO₂, and Al₂O₃ in connection with NO oxidation activity, adsorption of sulfate onto the support, Pt dispersion, and specific surface area of the catalyst. Furthermore, we investigated the catalytic performance of Pt/TiO₂/SiC in more detail under isothermal conditions and in a staged arrangement.     

Mean field modelling of NOx storage on Pt/BaO/Al2O3

A mean field model, for storage and desorption of NO_x in a Pt/BaO/Al₂O₃ catalyst is developed using data from flow reactor experiments. This relatively complex system is divided into five smaller sub-systems and the model is divided into the following steps: (i) NO oxidation on Pt/Al₂O₃; (ii) NO oxidation on Pt/BaO/Al₂O₃; (iii) NO_x storage on BaO/Al₂O₃; (iv) NO_x storage on Pt/BaO/Al₂O₃ with thermal regeneration and (v) NO_x storage on Pt/BaO/Al₂O₃ with regeneration using C₃H₆. In this paper, we focus on the last sub-system. The kinetic model for NO_x storage on Pt/BaO/Al₂O₃ was constructed with kinetic parameters obtained from the NO oxidation model together with a NO_x storage model on BaO/Al₂O₃. This model was not sufficient to describe the NO_x storage experiments for the Pt/BaO/Al₂O₃, because the NO_x desorption in TPD experiments was larger for Pt/BaO/Al₂O₃, compared to BaO/Al₂O₃. The model was therefore modified by adding a reversible spill-over step. Further, the model was validated with additional experiments, which showed that NO significantly promoted desorption of NO_x from Pt/BaO/Al₂O₃. To this NO_x storage model, additional steps were added to describe the reduction by hydrocarbon in experiments with NO₂ and C₃H₆. The main reactions for continuous reduction of NO_x occurs on Pt by reactions between hydrocarbon species and NO in the model. The model is also able to describe the reduction phase, the storage and NO breakthrough peaks, observed in experiments.     

Catalytic oxidation of HCN over a 0.5% Pt/Al2O3 catalyst

The adsorption of HCN on, its catalytic oxidation with 6% O₂ over 0.5% Pt/Al₂O₃, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N₂O, NO and NO₂, and some residual adsorbed N-containing species were oxidized to NO and NO₂ during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N₂ and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N₂O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO_x in the products. The co-feeding of H₂O and C₃H₆ had little, if any effect on the total HCN conversion, but C₃H₆ addition did increase the conversion to NO and decrease the conversion to NO₂, perhaps due to the competing presence of adsorbed fragments of reductive C₃H₆. Evidence is also presented that introduction of NO and NO₂ into the reactant gas mixture resulted in additional reaction pathways between these NO_x species and HCN that provide for lean-NO_x reduction coincident with HCN oxidation.     

Synthesis of CeO2–MnOx mixed oxides and catalytic performance under oxygen-rich condition

Ce_0.5Zr_0.5O₂, Ce_0.5Zr_0.2Mn_0.3O₂ and Ce_0.5Mn_0.5O₂ were prepared by citric acid sol–gel method. The effect of manganese on the structural and redox properties of ceria-based mixed oxides was investigated by means of powder X-ray diffraction, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller analyses, temperature-programmed reduction and catalytic activity evaluation in the presence of excess O₂. The results showed that some Mn cations could enter into the ceria lattice to form solid solutions. Mn₃O₄ appeared due to the instability of the mixed oxides with increment of the Mn doping ratio while another oxide Mn₂O₃ is detected in the physical mixture of ceria and manganese oxide. These Mn-doped mixed oxides, especially Ce_0.5Mn_0.5O₂, presented better catalytic activities than Ce_0.5Zr_0.5O₂ and even Pt-loaded catalyst for total oxidation of C₃H₈ and oxidative sorption of NO in the presence of excess oxygen. The oxidation ability of Mn and the strong interaction between Mn and Ce were suggested to promote the oxygen storage/transport capacity of the mixed oxides as well as reactive adsorption of nitric oxide and hydrocarbons.     

Influence of metal oxides on the catalytic behavior of Au/Al2O3 for the selective reduction of NOx by hydrocarbons

The reduction of NO by propene in the presence of excess oxygen over mechanical mixtures of Au/Al₂O₃ with a bulk oxide has been investigated. The oxides studied were: Co₃O₄, Mn₂O₃, Cr₂O₃, CuO, Fe₂O₃, NiO, CeO₂, SnO₂, ZnO and V₂O₅. Under lean C₃H₆-SCR conditions, these oxides (with the exception of SnO₂) convert selectively NO to NO₂. When mechanically mixed with Au/Al₂O₃, the Mn₂O₃ and Co₃O₄ oxides and, to a much greater extent, CeO₂ act synergistically with this catalyst greatly enhancing its SCR performance. It was found that their synergistic action is not straightforwardly related to their activity for NO oxidation to NO₂. The exhibited catalytic synergy may be due to the operation of either remote control or a bifunctional mechanism. In the later case, the key intermediate must be a short-lived compound and not the NO₂ molecule in gas-phase.     

Enhanced activity of metal oxide-doped Ga2O3–Al2O3 for NO reduction by propene

Effect of additives, In₂O₃, SnO₂, CoO, CuO and Ag, on the catalytic performance of Ga₂O₃–Al₂O₃ prepared by sol–gel method for the selective reduction of NO with propene in the presence of oxygen was studied. As for the reaction in the absence of H₂O, CoO, CuO and Ag showed good additive effect. When H₂O was added to the reaction gas, the activity of CoO-, CuO- and Ag-doped Ga₂O₃–Al₂O₃ was depressed considerably, while an intensifying effect of H₂O was observed for In₂O₃- and SnO₂-doped Ga₂O₃–Al₂O₃. Of several metal oxide additives, In₂O₃-doped Ga₂O₃–Al₂O₃ showed the highest activity for NO reduction by propene in the presence of H₂O. Kinetic studies on NO reduction over In₂O₃–Ga₂O₃–Al₂O₃ revealed that the rate-determining step in the absence of H₂O is the reaction of NO₂ formed on Ga₂O₃–Al₂O₃ with C₃H₆-derived species, whereas that in the presence of H₂O is the formation of C₃H₆-derived species. We presumed the reason for the promotional effect of H₂O as follows: the rate for the formation of C₃H₆-derived species in the presence of H₂O is sufficiently fast compared with that for the reaction of NO₂ with C₃H₆-derived species in the absence of H₂O. Although the retarding effect of SO₂ on the activity was observed for all of the catalysts, SnO₂–Ga₂O₃–Al₂O₃ showed still relatively high activity in the lower temperature region.     

Synthesis of C2H4 by partial oxidation of CH4 over LiCl/NiO

Alkali halide added transition metal oxides produced ethylene selectively in oxidative coupling of methane. The role of alkali halides has been investigated for LiCl-added NiO (LiCl/NiO). In the absence of LiCl the reaction over NiO produced only carbon oxides (CO₂ + CO). However, addition of LiCl drastically improved the yield of C₂ compounds (C₂H₆ + C₂H₄). One of the roles of LiCl is to inhibit the catalytic activity of the host NiO for deep oxidation of CH₄. The reaction catalyzed by the LiCl/NiO proceeds stepwise from CH₄ to C₂H₄ through C₂H₆ (2CH₄ → C₂H₆ → C₂H₄). The study on the oxidation of C₂H₆ over the LiCl/NiO showed that the oxidative dehydrogenation of C₂H₆ to C₂H₄ occurs very selectively, which is the main reason why partial oxidation of CH₄ over LiCl/NiO gives C₂H₄ quite selectively. The other role of LiCl is to prevent the host oxide (NiO) from being reduced by CH₄. The catalyst model under working conditions was suggested to be the NiO covered with molten LiCl. XPS studies suggested that the catalytically active species on the LiCl/NiO is a surface compound oxide which has higher valent nickel cations (Ni^(2+δ)+ or Ni³⁺). The catalyst was deactivated at the temperatures>973 K due to vaporization of LiCl and consumption of chlorine during reaction. The kinetic and CH₄---CD₄ exchange studies suggested that the rate-determining step of the reaction is the abstraction of H from the vibrationally excited methane by the molecular oxygen adsorbed on the surface compound oxide.     

Effect of rare-earth element oxides (La2O3, Ce2O3) on the structural and physico-chemical characteristics of Pd/Al2O3 monolithic catalysts of nitrogen oxide reduction by methane

It is shown that introduction of additives of rare-earth element oxides (La₂O₃, CeO₂) enables regulating the structural and functional characteristics of Pd/Al₂O₃-catalysts (applied on ceramic monoliths of honeycomb structure) of nitrogen oxide reduction by methane. Modifying additives provide increase of thermal stability of porous structure of both highly dispersed Al₂O₃, as the second support, and the catalyst as a whole.

Contribution of La₂O₃ and CeO₂ in increasing the thermal stability is of an additive nature, and lanthanum oxide shows the higher efficiency than cerium one. According to X-ray phase analysis data, stabilizing action is conditioned by occurrence of rare-earth element oxides into lattice of Al₂O₃, which retards diffusional processes leading to phase transitions of low-temperature crystalline modifications of alumina into high-temperature ones with a low specific surface. For the catalyst samples modified with La₂O₃ an effect of thermal activation is observed, which is revealed by increase in catalytic activity as a result of annealing at 850 °C. Such a phenomenon, as shown by means of X-ray photoelectron spectroscopy technique, can be explained via stabilization of palladium in singly charged state in the form of groups of Pd⁺O₂⁻ and corresponding increase in concentration of active centers.