Experimental Investigation of the Binary Mn-Sb Phase Diagram

The binary manganese-antimony (Mn-Sb) phase diagram was reinvestigated in the whole composition range using powder-XRD, DTA and SEM-EDX. The phase boundaries and melting temperatures of the ferromagnetic phases MnSb and Mn₂Sb were modified by taking into account the new experimental data. Most of the reaction temperatures could be verified within a range of ±10 °C. Nevertheless, a few temperatures had to be revised, such as the eutectic reaction L → β-Mn + Mn ₂ Sb at 893 °C and the eutectoid reaction β-Mn → α-Mn + Mn ₂ Sb at 718 °C. The previously reported peritectic melting behavior of MnSb could be confirmed. The variation of the lattice parameters of the NiAs-(B8 ₁ ) type MnSb phase with composition was determined. A revised version of the of the Mn-Sb phase diagram is presented.     

Crystal Structure of Delta-Prime Plutonium And the Thermal Expansion Characteristics Of Delta,Delta-Prime,and Epsilon Plutonium

The σ′ plutonium is found to be body-centered-tetragonal with two atoms per unit cell at 000 and 1/2, 1/2, 1/2. The unit cell dimensions at 477°C are α = 3.339 ± 0.003Å and c = 4.446 ± 0.007Å, which lead to a calculated density of 16.01 g per eu cm. Each plutonium atom is surrounded by 12 others at a mean distance of 3.275?. The linear coefficient of thermal expansion perpendicular to the c-axis is 10⁶ ?_a = 305 ±35 per °C, and parallel to the c-axis is 10⁶ ?_c=?659 ± 67 per °C. The average linear coefficient, (2?_a + ?_c)/3, is equal to 10⁶?_L = ?18 ± 28 per °C. The linear coefficient of themal expansion of face-centered-cubic σ plutonium is found to be 10⁶ ?_L=?8.6 ± 0.3 per °C, and of body-centered-cubic ∈ plutonium 10⁶ ?_L = 36.5 ±1.1 per °C.     

X-Ray Diffraction Determination of The Coefficients of Expansion of Alpha Uranium

The unit cell dimensions of orthorhombic uranium have been determined over the temperature range —253° to 640°C. Above room temperature (27°C), these data were found to fit the equations at = a27 [1 + 17.2 × 10-6 (t —27) + 30.8 × 10-9 (t — 27)2] bt = b27[1 — 9.2 × 10-6 (t —27) + 40.4 × 10-⁹ (t —27) 2 — 67.5 × 10-12 (t —27)3] ct = c27[1+25.1 × 10-⁶ (t —27) — 21.3 × 10-9 (t —27)2 + 57.5 × 10-12 (t —27)3]. Mean coefficients were computed. Over the range —253° to 100°C, these were compared with dilatometer data.     

Evolution of grain–subgrain structure and carbide subsystem upon annealing of a low-carbon low-alloy steel subjected to high-pressure torsion

The effect of annealing on the evolution of an ultrafine-grain structure and carbides in a 06MBF steel (Fe–0.1Mo–0.6Mn–0.8Cr–0.2Ni–0.3Si–0.2Cu–0.1V–0.03Ti–0.06Nb–0.09C, wt %) has been studied. The grain–subgrain structure (d = 102 ± 55 nm) formed by high-pressure torsion and stabilized by dispersed (MC, M₃C, d = 3–4 nm) and relatively coarse carbides (M₃C, d = 15–20 nm) is stable up to a temperature of 500°C (1 h) (d = 112 ± 64 nm). Annealing at a temperature of 500°C is accompanied by the formation in regions with a subgrain structure of recrystallized grains, the size of which is close to the size of subgrains formed by high-pressure torsion. The average size and distribution of dispersed particles change weakly. The precipitation hardening and the increase in the fraction of high-angle boundaries in the structure cause an increase in the values of the microhardness to 6.4 ± 0.2 GPa after annealing at 500°C as compared to the deformed state (6.0 ± 0.1 GPa). After 1-h annealing at 600 and 700°C, the microcrystal size (d = 390 ± 270 nm and 1.7 ± 0.7 μm, respectively) increases; the coarse M₃C (≈ 50 nm) and dispersed carbides grow by 5 and 8 nm, respectively. The value of the activation energy for grain growth Q = 516 ± 31 kJ/mol upon annealing of the ultrafine-grained steel 06MBF produced by high-pressure torsion exceeds the values determined in the 06MBF steel with a submicrocrystalline structure formed by equal-channel angular pressing and in the nanocrystalline α iron.     

Phase Equilibria in the Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript>–InSb System

The phase diagram of the (Sb₂Te₃)_100?x –InSb _x system was determined based on x-ray diffraction (XRD) analysis, differential thermal analysis (DTA), and microhardness and density measurements. An intermediate compound with composition Sb₂Te₃·2InSb was formed as a result of syntectic reaction, melting incongruently at 553 °C. This compound has tetragonal lattice with unit cell parameters of a = 4.3937 Å, b = 4.2035 Å, c = 3.5433 Å, α = 93.354°, and β = γ = 90°. Sb₂Te₃·(2 + δ)InSb (?1 ≤ δ ≤ +1) and (Sb₂Te₃)_100?x (InSb) _x (90 ≤ x ≤ 100) solid solutions exist in the investigated system, based on the intermediate compound Sb₂Te₃·2InSb and on InSb, respectively. Also, two invariant equilibria exist in the system, with eutectic point coordinates at compositions of x = 60 and x ≈ 85 mol% InSb and eutectic temperatures of T _E = 541 and T _E ≈ 501 °C, respectively.     

Microstructures,Martensitic Transformation,and Mechanical Behavior of Rapidly Solidified Ti-Ni-Hf and Ti-Ni-Si Shape Memory Alloys

In this work, the microstructure and mechanical properties of rapidly solidified Ti_50?x/2Ni_50?x/2Hf _x (x = 0, 2, 4, 6, 8, 10, and 12 at.%) and Ti_50?y/2Ni_50?y/2Si _y (y = 1, 2, 3, 5, 7, and 10 at.%) shape memory alloys (SMAs) were investigated. The sequence of the phase formation and transformations in dependence on the chemical composition is established. Rapidly solidified Ti-Ni-Hf or Ti-Ni-Si SMAs are found to show relatively high yield strength and large ductility for specific Hf or Si concentrations, which is due to the gradual disappearance of the phase transformation from austenite to twinned martensite and the predominance of the phase transformation from twinned martensite to detwinned martensite during deformation as well as to the refinement of dendrites and the precipitation of brittle intermetallic compounds.     

The Microstructural Evolution and Special Flow Behavior of Ti-5Al-2Sn-2Zr-4Mo-4Cr During Isothermal Compression at a Low Strain Rate

The microstructural evolution and special flow behavior of Ti-5Al-2Sn-2Zr-4Mo-4Cr during isothermal compression at a strain rate of 0.0001 s^?1 were investigated. The dislocation climbs in elongated α grains resulted in the formation of low-angle boundaries that transform into high-angle boundaries with greater deformation, and the elongated α grains subsequently separated into homogenous globular α grains with the penetration of the β phase. The simultaneous occurrence of discontinuous dynamic recrystallization and continuous dynamic recrystallization in the primary β grains resulted in a trimode grain distribution. The β grains surrounded by dislocations presented an equilateral-hexagonal morphology, which suggests that grain boundary sliding through dislocation climbs was the main deformation mechanism. The true stress–strain curves for 1073 and 1113 K abnormally intersect at a strain of ~0.35, related to the α → β phase transformation and distinct growth of the β grain size.     

Correlation between the Hall Resistance and Magnetoresistance in the Mixed State of an Nd<Subscript>2 − <Emphasis Type="Italic">x</Emphasis></Subscript>Ce<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>CuO<Subscript>4 + δ</Subscript> Electronic Superconductor

The Hall resistance and the magnetoresistance in the mixed state of the Nd_{2 ? x}Ce _x CuO_{4 + δ} quasi-two-dimensional system near the antiferromagnetic-superconductor (AF-SC) phase transition have been measured at doping levels x = 0.14 and 0.15, and a correlation has been established. This correlation can be analyzed using the following power relationship: ρ _xy (B) ~ [ρ _xx (B)]^β. It was found that index β varied from 0.94 ± 0.03 in the region of AF and SC coexistence (x = 0.14) to 0.6 ± 0.1 in the SC region with the maximum critical temperature (x = 0.15) at low temperatures and weak magnetic fields. This reduction suggests that the symmetry of carrier pairing changes at the boundary of the transition from the phase of antiferromagnetic ordering and spin density waves to the superconducting phase in the presence of antiferromagnetic spin fluctuations.     

Deformation mechanisms in Cr20Ni80 alloy at elevated temperatures

The mechanisms of plastic deformation of Cr20Ni80 nichrome with an initial grain size of 80 μm were studied in the temperature range 600–950°C and the strain-rate range 1.5 × 10^?6?5 × 10^?2s^?1. Nichrome is shown to exhibit anomalously high values of stress exponent n and a high deformation activation energy Q. These unusual properties were found to be caused by “threshold” stresses below which deformation does not occur. An analysis of the deformation behavior with allowance for threshold stresses reveals the regions of hot, warm, and cold deformation in nichrome. At normalized strain rates \(\dot \varepsilon \) kT/D _{1 Gb} < 10^?8, the true values of n and Q are ～4 and 285 ± 30 kJ/mol, respectively. In the normalized-strain range 10^?8?10^?4 n ～ 6 and the deformation activation energy decreases to 175 ± 30 kJ/mol. This change in the deformation-behavior characteristics is explained by the transition from high-temperature dislocation climb, which is controlled by lattice self-diffusion, to low-temperature dislocation climb, which is controlled by pipe diffusion, as the temperature decreases. At \(\dot \varepsilon \) kT/D _{1 Gb} = 10^?4, a power law break-down takes place and an exponential law (which describes the deformation behavior in the range of cold deformation) becomes operative.     

Self-Diffusion in Magnesium Single Crystals

Radioactive Mg²⁸ has been used to study the rate of self-diffusion in oriented single crystals of magnesium in the temperature range 468° to 635°C. The diffusion coefficients parallel and perpendicular to the c-axis are: On = 1.0 exp (—32,200/KTJ cm² per sec and D₁ = 1.5 exp (—32,500/RT) cm² per sec. The ratio D₁/D₁₁ was found to vary from 1.13 at 468° to 1.24 at 575°C. Assuming a vacancy mechanism, an explanation of this anisotropy of diffusion follows from a consideration of the difference in the saddle points for diffusion in and out of the basal plane.     

The Binary Bi-Rh Phase Diagram: Stable and Metastable Phases

The binary bismuth-rhodium (Bi-Rh) phase diagram was reinvestigated from 23 to 60 at.% Rh with focus on the BiRh phase, applying powder-x-ray diffraction (XRD), high temperature powder-XRD, differential thermal analyses and scanning electron microscopy. The phase boundaries of the BiRh phase at 750 °C and the temperature of its peritectic decomposition were refined. In addition, the existence of the two phases Bi₄Rh and Bi₂Rh (in two modifications depending on temperature) could be confirmed. Most of the reaction temperatures reported in the literature could be verified within a range of about ± 10 °C. Nevertheless, a few temperatures had to be revised, such as those of the peritectic reactions L + Rh \(\rightleftharpoons\) BiRh at 979 °C and L + BiRh \(\rightleftharpoons\) β-Bi₂Rh at 785 °C. No evidence could be found for the presence of a stable Bi₃Rh phase in well annealed samples; from the present results it must be concluded that Bi₃Rh is actually metastable. On the other hand, a new orthorhombic phase BiRh_0.81 was discovered which crystallizes in the MnP structure type (Pmna). It was found that the temperatures of the transition between the low-temperature modification α-Bi₂Rh and its high-temperature form β-Bi₂Rh depend considerably on the presence or absence of metastable Bi₃Rh and stable BiRh_0.81, respectively.     

Phase Equilibria of the Ternary Al-Cu-Zn Alloys on Al-Zn Rich Side

Phase equilibria of the Al-Cu-Zn system on Al-Zn rich side was experimentally determined with 16 alloys annealed at 360 °C. The annealed alloys were examined by means of x-ray diffraction, electron probe microanalysis and differential scanning calorimetry. Five single-phase regions and seven two-phase regions as well as three three-phase regions, i.e. α-(Al)?+?θ-Al₂Cu?+?τ′-Al₄Cu₃Zn, α-(Al)?+?τ′-Al₄Cu₃Zn?+?ε-CuZn₄ and α-(Al)?+?ε-CuZn₄?+?(Zn), were determined. The partial isothermal section of the Al-Cu-Zn system on Al-Zn rich side at 360 °C was constructed based on the obtained experimental data in this work. It was observed that the solid solution phase α-(Al) would easily decompose into ε-CuZn₄, (Zn) and α′-(Al) at the ambient temperature in the early stages. The ternary phase τ′-Al₄Cu₃Zn would form and ε-CuZn₄ would disappear gradually along with the extension of aging time.     

X-ray diffraction determination of root-mean-square displacements of atoms in <Emphasis Type="Italic">B</Emphasis>2 and <Emphasis Type="Italic">R</Emphasis> phases of titanium nickelide

Intensities of 15 fundamental and 11 superlattice reflections of the B2 phase have been measured in a titanium nickelide single crystal using X-ray Mo Kα radiation. Structure factors for these reflections and root-mean-square displacements of nickel and titanium atoms from the crystal-lattice sites have been calculated. The mean squared displacements of nickel atoms are equal to 〈u ²〉_Ni=0.087 ± 0.006 Ų; those of titanium atoms, 〈u ²〉_Ti = 0.039 ± 0.003 Ų. The temperature dependence of root-mean-square displacements in the B2 phase and in the temperature range of the B2 → R transformation has been determined. Root-mean-square atomic displacements in the R phase have been calculated. The Debye temperature has been determined and the root-mean-square atomic displacements in the B2 phase have been separated into static and dynamic ones.     

Influence of Nb on microstructure and mechanical properties of Ti-Sn ultrafine eutectic alloy

In this study, A series of the high strength (T₈₂Sn₁₈)_100-xNb_x (x=0, 1, 3, 5, and 9 at%) ultrafine eutectic alloys with large plasticity are developed by suction casting method. The Ti₈₂Sn₁₈ binary eutectic alloy consists of a mixture of a hcp Ti₃Sn and a α-Ti phases having the plate-like lamellar type duplex structure with micro scaled eutectic colony. From the (T₈₂Sn₁₈)₉₇Nb₃, the alloy display structural heterogeneous distribution of ultrafine-scaled phases composed of β-Ti(Nb) solid solution surrounded by alternating plate-like shaped Ti₃Sn and α-Ti phases. With increasing Nb content, the volume fraction of β-Ti is continuously increased, which induced improving mechanical properties both strength and plasticity. Especially, (Ti₈₂Sn₁₈)₉₁Nb₉ alloy has the outstanding combination of the high strength (σ _y ≈1.1 GPa) and large plasticity (ε _p ≈36%) at room temperature.     

Phase Equilibria in the Cu-Sn-Sb Ternary System

The phase equilibria in the Cu-Sn-Sb ternary system were investigated by means of electron-probe microanalysis and x-ray diffraction. Firstly, ternary solubilities of η-Cu₆Sn₅, δ-Cu₄₁Sn₁₁, Cu₁₁Sb₃, ε-Cu₃Sb and η-Cu₂Sb, were less than 7 at.% Sb or Sn at 400 °C. Besides, an re-stabilized ternary solubility, Cu₆(Sn,Sb)₅, was detected with a homogeneity range of Cu: 52.9-53.3 at.%, Sn: 28.4-30.9 at.%, and Sb: 15.8-18.7 at.%. Its origin was traced back to high-temperature stabilization of the binary η-Cu₆Sn₅ phase. Thirdly, the metastable phase, Cu₁₁Sb₃, was observed at 400 °C in the Cu-Sn-Sb ternary system; On raising the temperature to 500 °C, the ε-Cu₃Sn phase still retained a large solubility for Sb, at?~?16 at.%, while the ε-Cu₃Sb was replaced by β-Cu₃Sb with a dual-cornered large homogeneity range. Similarly, a ternary homogeneity range of Cu: 83.8-84.9 at.%, Sn: 2.6-6.2 at.%, and Sb: 9-12.5 at.%, was found and deduced to be the high temperature stabilization phase of γ-Cu₁₁(Sb,Sn)₂ at 500 °C.     

Phase Equilibria of the Co-Mo-Zr Ternary System at 1000 °C

The isothermal section of the Co-Mo-Zr ternary system at 1000 °C was investigated by using 29 alloys. The annealed alloys were examined by means of x-ray diffraction, optical microscopy, and electron probe microanalysis. It was confirmed that three ternary phases, λ₁ (Co_0.5-1.5Mo_1.5-0.5Zr, hP12-MgZn₂), ω (CoMoZr₄) and κ (CoMo₄Zr₉, hP28-Hf₉Mo₄B), exist in the Co-Mo-Zr ternary system at 1000 °C. And the experimental results also indicated that there are sixteen three-phase regions at 1000 °C. Thirteen of them were well determined in the present work: (1) (γCo)?+?Co₁₁Zr₂?+?Co₂₃Zr₆, (2) (γCo)?+?Co₂₃Zr₆?+?ε-Co₃Mo, (3) Co₂₃Zr₆?+?ε-Co₃Mo?+?μ-Co₇Mo₆, (4) (Mo)?+?μ-Co₇Mo₆?+?Co₂Zr, (5) (Mo)?+?Co₂Zr?+?λ₁, (6) (Mo)?+?Mo₂Zr?+?λ₁, (7) λ₁?+?Mo₂Zr?+?CoZr, (8) Co₂Zr?+?CoZr?+?λ₁, (9) Mo₂Zr?+?CoZr₂?+?ω, (10) κ?+?Mo₂Zr?+?ω, (11) CoZr₂?+?liquid?+?ω, (12) (βZr)?+?liquid?+?ω and (13) (βZr)?+?κ?+?ω. The homogeneity of λ₁ spans in the range of 28.66-50.77 at.% Co and 15.71-37.03 at.% Mo, and that for ω is within the range of 18.66-23.64 at.% Co and 8.53-14.68 at.% Mo. The homogeneity range for κ is from 8.09 at.% to 9.94 at.% Co and 23.13 at.% to 25.58 at.% Mo. The maximum solubility of Zr in μ-Co₇Mo₆ phase, Mo in Co₂Zr phase and Co in Mo₂Zr phase were determined to be 6.17, 11.27 and 9.14 at.%, respectively. While the solubility of Zr in ε-Co₃Mo and (γCo) phases, Mo in Co₁₁Zr₂ and CoZr phases were detected to be extremely small. According to this work, the Co₂₃Zr₆ phase contained 15.61 at.% Mo and 12.7 at.% Zr. In addition, the maximum solubility of Co and Zr in (Mo) phase and Mo in (γCo) phase were measured to be 3.50, 5.44 and 7.40 at.%, respectively.     

Phase and structural transformations in the alloy on the basis of the orthorhombic titanium aluminide

Phase and structural transformations in the Ti-24.3 Al-24.8 Nb-1.0 Zr-1.4 V-0.6 Mo-0.3 Si (at %) alloy that take place during heating in the temperature range of 700–1050°C have been investigated. The temperature ranges of existence of the O + β, O + β + α₂, β + α₂, and β phase fields have been established. A scheme of the relationships between the volume fractions of the O, β, and α₂ phases depending on the temperature of heating of the alloy have been investigated. The formation of an ordered incommensurate ω (V _ω) phase has been revealed in the alloy during quenching from 900°C. The existence of a correlation between the hardness properties and changes in the phase composition and morphology of particles precipitating in the alloy has been shown.     

Properties of the Ti<Subscript>40</Subscript>Zr<Subscript>10</Subscript>Cu<Subscript>36</Subscript>Pd<Subscript>14</Subscript> BMG Modified by Sn and Nb Additions

The results of investigation of the influence of additions of 2 and 3 at.% of Sn and simultaneously of Sn and 3 at.% Nb on microstructure and properties of the bulk metallic glasses of composition (Ti₄₀Cu_36?x Zr₁₀Pd₁₄Sn _x )_100?y Nb _y are reported. It was found that the additions of Sn increased the temperatures of glass transition (T _g), primary crystallization (T _x ), melting, and liquidus as well as supercooled liquid range (ΔT) and glass forming ability (GFA). The nanohardness and elastic modulus decreased in alloys with 2 and 3 at.% Sn additions, revealing similar values. The 3 at.% Nb addition to the Sn-containing amorphous phase decreased as well all the T _g, T _x , T _L, and T _m temperatures as ΔT and GFA; however, relatively larger values of this parameters in alloys containing larger Sn content were preserved. In difference to the previously published results, in the case of the amorphous alloys containing small Nb and Sn additions, a noticeable amount of the quenched-in crystalline phases was not confirmed, at least of the micrometric sizes. In the case of the alloys containing Sn or both Sn and Nb, two slightly different amorphous phase compositions were detected, suggesting separation in the liquid phase. Phase composition of the alloys determined after amorphous phase crystallization was similar for all compositions. The phases Cu₈Zr_3, CuTiZr, and Pd₃Zr were mainly identified in the proportions dependent on the alloy compositions.     

Effect of Testing Variables on the Hydrogen Embrittlement of Titanium and a Ti-8 pct Mn Alloy

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an α-β alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the α-β alloy also. However, increasing the testing speed generally decreased the transition temperature of the α-β alloy.     

Correlation Between the Pitting Potential Evolution and $$\varvec\sigma$$ Phase Precipitation Kinetics in the 2205 Duplex Stainless Steel

The aim of this work is to correlate the pitting potential (E_pit) evolution with the kinetics of σ phase precipitation in the 2205 duplex stainless steel aged at 850 °C after solution treatment at 1150 °C. The potentiodynamic polarization curves indicate a reduction of the pitting corrosion resistance with the aging time, which is revealed by a decrease in the E_pit values from 0.65 to 0.40 V_SCE. Thus, E_pit values are used to determine the kinetics parameters of the σ phase precipitation. The experimental transformed fraction agrees well with the one calculated by using the modified Kolmogorov–Johnson–Mehl–Avrami equation with an impingement parameter c?=?0.6.