Marciniak–Kuczynski type modelling of the effect of Through-Thickness Shear on the forming limits of sheet metal

The Marciniak–Kuczynski (MK) forming limit model is extended in order to predict localized necking in sheet metal forming operations in which Through-Thickness Shear (TTS), also known as out-of-plane shear, occurs. An example of such a forming operation is Single Point Incremental Forming. The Forming Limit Diagram (FLD) of a purely plastic, isotropic hardening material with von Mises yield locus is discussed, for monotonic deformation paths that include TTS. If TTS is present in the plane containing the critical groove direction in the MK model, it is seen that formability is increased for all in-plane strain modes, except equibiaxial stretching. The increase in formability due to TTS is explained through a detailed study of some selected deformation modes. The underlying mechanism is a change of the stress mode in the groove that results in a delay of the onset of localized necking.     

A non-associated constitutive model with mixed iso-kinematic hardening for finite element simulation of sheet metal forming

In this paper an anisotropic material model based on non-associated flow rule and mixed isotropic–kinematic hardening was developed and implemented into a user-defined material (UMAT) subroutine for the commercial finite element code ABAQUS. Both yield function and plastic potential were defined in the form of Hill’s [Hill, R., 1948. A theory of the yielding and plastic flow of anisotropic metals. Proc. R. Soc. Lond. A 193, 281–297] quadratic anisotropic function, where the coefficients for the yield function were determined from the yield stresses in different material orientations, and those of the plastic potential were determined from the r-values in different directions. Isotropic hardening follows a nonlinear behavior, generally in the power law form for most grades of steel and the exponential law form for aluminum alloys. Also, a kinematic hardening law was implemented to account for cyclic loading effects. The evolution of the backstress tensor was modeled based on the nonlinear kinematic hardening theory (Armstrong–Frederick formulation). Computational plasticity equations were then formulated by using a return-mapping algorithm to integrate the stress over each time increment. Either explicit or implicit time integration schemes can be used for this model. Finally, the implemented material model was utilized to simulate two sheet metal forming processes: the cup drawing of AA2090-T3, and the springback of the channel drawing of two sheet materials (DP600 and AA6022-T43). Experimental cyclic shear tests were carried out in order to determine the cyclic stress–strain behavior and the Bauschinger ratio. The in-plane anisotropy (r-value and yield stress directionalities) of these sheet materials was also compared with the results of numerical simulations using the non-associated model. These results showed that this non-associated, mixed hardening model significantly improves the prediction of earing in the cup drawing process and the prediction of springback in the sidewall of drawn channel sections, even when a simple quadratic constitutive model is used.     

Finite element modeling of plastic anisotropy induced by texture and strain-path change

Consideration of plastic anisotropy is essential in accurate simulations of metal forming processes. In this study, finite element (FE) simulations have been performed to predict the plastic anisotropy of sheet metals using a texture- and microstructure-based constitutive model. The effect of crystallographic texture is incorporated through the use of an anisotropic plastic potential in strain-rate space, which gives the shape of the yield locus. The effect of dislocation is captured by use of a hardening model with four internal variables, which characterize the position and the size of the yield locus. Two applications are presented to evaluate the accuracy and the efficiency of the model: a cup drawing test and a two-stage pseudo-orthogonal sequential test (biaxial stretching in hydraulic bulging followed by uniaxial tension), using an interstitial-free steel sheet. The experimental results of earing behavior in the cup drawing test, maximum pressure and strain distribution in bulging, and transient hardening in the sequential test are compared against the FE predictions. It is shown that the current model is capable of predicting the plastic anisotropy induced by both the texture and the strain-path change. The relative significance of texture and strain-path change in the predictions is discussed.     

A combined necking and shear localization analysis for aluminum sheets under biaxial stretching conditions

A combined necking and shear localization analysis is adopted to model the failures of two aluminum sheets, AA5754 and AA6111, under biaxial stretching conditions. The approach is based on the assumption that the reduction of thickness or the necking mode is modeled by a plane stress formulation and the final failure mode of shear localization is modeled by a generalized plane strain formulation. The sheet material is modeled by an elastic-viscoplastic constitutive relation that accounts for the potential surface curvature, material plastic anisotropy, material rate sensitivity, and the softening due to the nucleation, growth, and coalescence of microvoids. Specifically, the necking/shear failure of the aluminum sheets is modeled under uniaxial tension, plane strain tension and equal biaxial tension. The results based on the mechanics model presented in this paper are in agreement with those based on the forming limit diagrams (FLDs) and tensile tests. When the necking mode is suppressed, the failure strains are also determined under plane strain conditions. These failure strains can be used as guidances for estimation of the surface failure strains on the stretching sides of the aluminum sheets under plane strain bending conditions. The estimated surface failure strains are higher than the failure strains of the forming limit diagrams under plane strain stretching conditions. The results are consistent with experimental observations where the surface failure strains of the aluminum sheets increase significantly on the stretching sides of the sheets under bending conditions. The results also indicate that when a considerable amount of necking is observed for a sheet metal under stretching conditions, the surface failure strains on the stretching sides of the sheet metal under bending conditions can be significantly higher.     

On the r-value of textured sheet metals

The r-value of a sheet metal is a measure of plastic anisotropy frequently used for prediction of performance in deep-drawing. It has also figured prominently in the literature for validation of theories where the predicted angular dependence of r is compared with the measured dependence. As plastic anisotropy in sheet metals is caused mainly by the preferred orientations of grains within the polycrystalline metal, it is natural to ask how r would depend on the orientation distribution function (ODF) w which defines the crystallographic texture of the polycrystal. In this paper a general formula relating r to w is derived for textured sheet metals whose plastic flow behavior is governed by a plastic potential f(σ, w), the anisotropic part of which depends linearly on the texture coefficients; here σ denotes the deviator of the Cauchy stress. Specific forms of this formula for orthorhombic sheets of cubic and of hexagonal metals are explicitly given.     

A modified damage model for advanced high strength steel sheets

More often than not, better formability in the simple tension test implies better formability performance in other stretching modes, especially in hole expansion performance since deformation in the hole expansion test is perceived to be in the same simple tension deformation mode. However, when the hole expansion formability is evaluated particularly for the twinning induced plasticity (TWIP) steel, its performance is so poor compared to other automotive steels, even though the TWIP steel has significantly superior formability in the simple tension test. Therefore, hole expansion formability was experimentally and numerically studied for advanced high-strength grade steel sheets, TWIP940 and a transformation induced plasticity (TRIP) 590 steel sheet, as well as a high-strength grade 340R steel sheet, particularly in conjunction with formability in the simple tension test and its surface condition sensitivity. In order to characterize mechanical properties, simple tension tests were performed to determine anisotropic properties and strain rate sensitivities. To account for macro-crack formation, an inverse calibration method based on a damage model utilizing a triaxiality-dependent fracture criterion and hardening behavior with stiffness deterioration was developed. In this approach, the damage model was inversely calibrated by performing numerical simulations and experiments for the simple tension test (with specimens prepared by milling and punching). Then, the damage model was applied to formability study in the hole expansion test. The damage model along with the anisotropic yield function Hill (1948) incorporated into the ABAQUS/Explicit FEM code performed well to predict hole expansion ratios (HER) and their surface condition sensitivity, elucidating the cause of the lukewarm hole expansion performance and strong surface condition sensitivity of the TWIP steel compared to the others.     

塑性各向异性板料本构关系及冲压成形的数值模拟

推导了具有一般屈服函数形式的弹塑性速率型本构关系;给出了用于板料成形的Hill塑性各向异性屈服模型下本构关系的具体形式;用有限元动力显式计算程序MSC/DYTRAN模拟了金属板料的冲压成形;通过算例分析,考察了塑性各向异性对凸耳形成和大小以及对成形模拟结果准确性的影响;数值结果和实验结果表明：各向（厚向）异性本构模型比各向同性本构模型更真实地反映了板料的成形性。     

Texture development and plastic anisotropy of B.C.C. strain hardening sheet metals

A Taylor-like polycrystal model is adopted here to investigate the plastic behavior of body centered cubic (b.c.c.) sheet metals under plane-strain compression and the subsequent in-plane biaxial stretching conditions. The <111> pencil glide system is chosen for the slip mechanism for b.c.c. sheet metals. The {110} <111> and {112} <111> slip systems are also considered. Plane-strain compression is used to simulate the cold rolling processes of a low-carbon steel sheet. Based on the polycrystal model, pole figures for the sheet metal after plane-strain compression are obtained and compared with the corresponding experimental results. Also, the simulated plane-strain stress—strain relations are compared with the corresponding experimental results. For the sheet metal subjected to the subsequent in-plane biaxial stretching and shear, plastic potential surfaces are determined at a given small amount of plastic work. With the assumption of the equivalence of the plastic potential and the yield function with normality flow, the yield surfaces based on the simulations for the sheet metal are compared with those based on several phenomenological planar anisotropic yield criteria. The effects of the slip system and the magnitude of plastic work on the shape and size of the yield surfaces are shown. The plastic anisotropy of the sheet metal is investigated in terms of the uniaxial yield stresses in different planar orientations and the corresponding values of the anisotropy parameter R, defined as the ratio of the width plastic strain rate to the through-thickness plastic strain rate under in-plane uniaxial tensile loading. The uniaxial yield stresses and the values of R at different planar orientations from the polycrystal model can be fitted well by a yield function recently proposed by Barlat et al. (1997b).     

Evaluation of advanced anisotropic models with mixed hardening for general associated and non-associated flow metal plasticity

The main objective of this paper is to develop a generalized finite element formulation of stress integration method for non-quadratic yield functions and potentials with mixed nonlinear hardening under non-associated flow rule. Different approaches to analyze the anisotropic behavior of sheet materials were compared in this paper. The first model was based on a non-associated formulation with both quadratic yield and potential functions in the form of Hill’s (1948). The anisotropy coefficients in the yield and potential functions were determined from the yield stresses and r-values in different orientations, respectively. The second model was an associated non-quadratic model (Yld2000-2d) proposed by Barlat et al. (2003). The anisotropy in this model was introduced by using two linear transformations on the stress tensor. The third model was a non-quadratic non-associated model in which the yield function was defined based on Yld91 proposed by Barlat et al. (1991) and the potential function was defined based on Yld89 proposed by Barlat and Lian (1989). Anisotropy coefficients of Yld91 and Yld89 functions were determined by yield stresses and r-values, respectively. The formulations for the three models were derived for the mixed isotropic-nonlinear kinematic hardening framework that is more suitable for cyclic loadings (though it can easily be derived for pure isotropic hardening). After developing a general non-associated mixed hardening numerical stress integration algorithm based on backward-Euler method, all models were implemented in the commercial finite element code ABAQUS as user-defined material subroutines. Different sheet metal forming simulations were performed with these anisotropic models: cup drawing processes and springback of channel draw processes with different drawbead penetrations. The earing profiles and the springback results obtained from simulations with the three different models were compared with experimental results, while the computational costs were compared. Also, in-plane cyclic tension–compression tests for the extraction of the mixed hardening parameters used in the springback simulations were performed for two sheet materials.     

Advances in experiments on metal sheets and tubes in support of constitutive modeling and forming simulations

This work is a review of experimental methods for observing and modeling the anisotropic plastic behavior of metal sheets and tubes under a variety of loading paths, such as biaxial compression tests; biaxial tension tests on metal sheets and tubes using closed-loop electrohydraulic testing machines; the abrupt strain path change method for detecting a yield vertex and subsequent yield loci without unloading; in-plane stress reversal tests on metal sheets; and multistage tension tests. Observed material responses are compared with the predictions of phenomenological plasticity models. Special attention is paid to the plastic deformation behavior of materials commonly used in industry, and to verifying the validity of conventional anisotropic yield criteria for those materials and associated flow rules at large plastic strains. The effects of using appropriate anisotropic yield criteria on the accuracy of simulations of forming defects, such as large springback and fracture, are also presented to highlight the importance of accurate material testing and modeling.     

Characterization and development of an evolutionary yield function for the superconducting niobium sheet

Superconducting radio frequency (SRF) niobium cavities are widely used in high-energy physics to accelerate particle beams in particle accelerators. The performance of SRF cavities is affected by the microstructure and purity of the niobium sheet, surface quality, geometry, etc. Following optimum strain paths in the forming of these cavities can significantly control these parameters. To select these strain paths, however, information about the mechanical behavior, microstructure, and formability of the niobium sheet is required. Due to the lack of information, first an extensive experimental study was carried out to characterize the formability of the niobium sheet, followed by examining the suitability of Hill’s anisotropic yield function to model its plastic behavior. Results from this study showed that, due to intrinsic behavior, it is necessary to evolve the anisotropic coefficients of Hill’s yield function in order to properly model the plastic behavior of the niobium sheet. The accuracy of the newly developed evolutionary yield function was verified by applying it to the modeling of the hydrostatic bulging of the niobium sheet.     

Plane stress yield function for aluminum alloy sheets—part 1: theory

A new plane stress yield function that well describes the anisotropic behavior of sheet metals, in particular, aluminum alloy sheets, was proposed. The anisotropy of the function was introduced in the formulation using two linear transformations on the Cauchy stress tensor. It was shown that the accuracy of this new function was similar to that of other recently proposed non-quadratic yield functions. Moreover, it was proved that the function is convex in stress space. A new experiment was proposed to obtain one of the anisotropy coefficients. This new formulation is expected to be particularly suitable for finite element (FE) modeling simulations of sheet forming processes for aluminum alloy sheets.     

STUDY OF TEXTURE EFFECT ON STRAIN LOCALIZATION OF BCC STEEL SHEETS

Using elastic crystalline viscoplastic finite element (FE) annlysis, the formability of BCC steel sheets was assessed. An orientation probability assignment method in the FE modeling procedure, which can be categorized as an inhomogenized material modeling, was newly proposed. In the study, the crystal orientations of three materials, mild steel, dual phase steel and the high strength steel, were obtained by X-ray diffraction and orientation distribution function (ODF) analyses. The measured ODF results have revealed clearly different textures in the sheets, featured by orientation fibers, skeleton lines and selected orientations in Euler angle space, which are closely related to the plastic anisotropy. Then, the crystal orientations were assigned to FE integration points by using this ODF data, individually. The FE analyses of the standard limiting dome height(LDH) test show how the fiber textures affect the extent of strain localization in the forming processes. It was confirmed by comparison with experimental results that this FE code could predict the extreme strain localization and assess the sheet formability. The third author is indebted to the National Natural Science Foundation of China for financial support (Grant No. 59875025) to the research cooperation with OIT, Japan.     

A three-dimensional model of anisotropic hardening in metals and its application to the analysis of sheet metal formability

The hardening model proposed by Z. Mróz based on the uniaxial fatigue behavior of many metals is adopted to derive an incremental constitutive equation for general three-dimensional problems. This constitutive law is then employed in the analysis of metal forming problems to assess the influence of loading cycles, of the types involved in standard forming processes, on the ultimate formability of sheet metals. The predicted forming limit curves differ quantitatively from results obtained via an isotropie hardening model and differ qualitatively from those obtained via a kinematic model. Also investigated are the effects of such loading cycles on material response to simple tensile loading, which is often used to characterize a material. Significant differences between the present model and the other two models considered are observed in such characterizers of simple tensile behavior as the stress-strain curve, the anisotropy parameter and the uniform elongation. These differences suggest a rather simple experiment to identify the proper material model to be used in analyses of problems which involve loading cycles. Comparisons with some experimental results reveal that the employment of an anisotropic hardening model, such as the generalized Mróz model derived herein, is indeed crucial in accurately predicting material response to complicated loading histories.     

织构可调塑性本构模型标定及其应用

提出了利用率相关晶体塑性模型标定织相可调本构模型的求解步骤,得出了一组依赖于晶粒间相互作用假设而独立于具体板材织构的本构相关系数.以此为基础再结合板材织构系数所得出的本构模型系数可避免出现屈服面非外凸的情形.利用所提求解步骤对在不同热处理条件下产生不同织构的AL5052铝合金板的深拉成形过程进行了有限元模拟.结果再现了典型织构在板材成形过程中所出现的塑性各向异性,从而表明求解步骤的可行性.     

PREDICTION OF EARING IN TEXTURED ALUMINIUM SHEETS BASED ON CRYSTAL PLASTICITY

The phenomenon of earing is investigated in the present study based on the theory of crystal plasticity with the dynamic explicit finite element program developed. Firstly texture analysis is carried out of rolled aluminium alloy Al5052 by means of X-ray technique. Then from the texture coefficients an analytical expression for the orientation distribution function (ODF) is derived making use of the computer algebraic language Mathematica4.0, which makes it easier to discretize the ODF into a series of Eulerian angles representing the distribution of lattices and further the preferred orientation (texture) of crystals of the original sheets. For the polycrystal model, the material is described using crystal plasticity where each material point in grains with each grain modelled as an FCC crystal with 12 distinct slip systems. The modified Taylor theory of crystal plasticity is used and only the initial texture is taken into consideration during large plastic deformation. Numerical simulation of earing has been performed for an aluminium sheet with texture and one with crystals exhibiting random distribution to demonstrate the effect of texture of materials on their plastic anisotropy and formability. Project supported by the National Natural Science Foundation of China (No. 59875025).     

Analysis of sheet metal formability through isotropic and kinematic hardening models

The present paper aims at analysing the sheet metal formability through several isotropic and kinematic hardening models. Specifically, a special attention is paid to the physically-based hardening model of Teodosiu and Hu (1995), which accounts for the anisotropic work-hardening induced by the microstructural evolution at large strains, as well as to some more conventional hardening models, including the isotropic Swift strain-hardening power law, and the Voce saturation strain-hardening law, combined with a non-linear kinematic hardening described by the Armstrong–Frederick law. The onset of localized necking is simulated by an advanced sheet metal forming limit model which connects, through the Marciniak–Kuczinsky analysis, the hardening models with the anisotropic yield criterion Yld2000-2d (Barlat et al., 2003). Both linear and complex strain paths are taken into account. The selected material is a DC06 steel sheet. The validity of each model is assessed by comparing the predicted forming limits with experimental results carefully obtained on this steel. The origin of discrepancy in the predicted results using different hardening models is thoroughly analyzed.     

Overview on the Prediction Models for Sheet Metal Forming Failure:Necking and Ductile Fracture

The formability of the material determines the amount of available deformation before failure and thus is important for the production of various structural components in industries. The workability of materials is commonly evaluated by different forms of failure models during sheet metal forming(SMF) processes. In order to provide a whole picture about the prediction models for SMF failure, necking-related formability and ductile fracture-related formability studies in SMF processes are systematically summarized, the applicability and limitation of each model are highlighted, and the link between forming limit diagram and ductile fracture criterion is pointed out. Conclusions about some critical issues on failure in SMF are made.     

Strain localization analysis using a large deformation anisotropic elastic–plastic model coupled with damage

Sheet metal forming processes generally involve large deformations together with complex loading sequences. In order to improve numerical simulation predictions of sheet part forming, physically-based constitutive models are often required. The main objective of this paper is to analyze the strain localization phenomenon during the plastic deformation of sheet metals in the context of such advanced constitutive models. Most often, an accurate prediction of localization requires damage to be considered in the finite element simulation. For this purpose, an advanced, anisotropic elastic–plastic model, formulated within the large strain framework and taking strain-path changes into account, has been coupled with an isotropic damage model. This coupling is carried out within the framework of continuum damage mechanics. In order to detect the strain localization during sheet metal forming, Rice’s localization criterion has been considered, thus predicting the limit strains at the occurrence of shear bands as well as their orientation. The coupled elastic–plastic-damage model has been implemented in Abaqus/implicit. The application of the model to the prediction of Forming Limit Diagrams (FLDs) provided results that are consistent with the literature and emphasized the impact of the hardening model on the strain-path dependency of the FLD. The fully three-dimensional formulation adopted in the numerical development allowed for some new results – e.g. the out-of-plane orientation of the normal to the localization band, as well as more realistic values for its in-plane orientation.