The effect of velocity and dimension of solid nanoparticles on heat transfer in non-Newtonian nanofluid

In this investigation, the behavior of non-Newtonian nanofluid hydrodynamic and heat transfer are simulated. In this study, we numerically simulated a laminar forced non-Newtonian nanofluid flow containing a 0.5 wt% carboxy methyl cellulose (CMC) solutionin water as the base fluid with alumina at volume fractions of 0.5 and 1.5 as the solid nanoparticle. Numerical solution was modelled in Cartesian coordinate system in a two-dimensional microchannel in Reynolds number range of 10≤Re≤1000. The analyzed geometrical space here was a rectangular part of whose upper and bottom walls was influenced by a constant temperature. The effect of volume fraction of the nanoparticles, Reynolds number and non-Newtonian nanofluids was studied. In this research, the changes pressure drop, the Nusselt number, dimensionless temperature and heat transfer coefficient, caused by the motion of non-Newtonian nanofluids are described. The results indicated that the increase of the volume fraction of the solid nanoparticles and a reduction in the diameter of the nanoparticles would improve heat transfer which is more significant in Reynolds number. The results of the introduced parameters in the form of graphs drawing and for different parameters are compared.     

Intriguingly high convective heat transfer enhancement of nanofluid coolants in laminar flows

We reported on investigation of the convective heat transfer enhancement of nanofluids as coolants in laminar flows inside a circular copper tube with constant wall temperature. Nanofluids containing Al₂O₃, ZnO, TiO₂, and MgO nanoparticles were prepared with a mixture of 55 vol.% distilled water and 45 vol.% ethylene glycol as base fluid. It was found that the heat transfer behaviors of the nanofluids were highly depended on the volume fraction, average size, species of the suspended nanoparticles and the flow conditions. MgO, Al₂O₃, and ZnO nanofluids exhibited superior enhancements of heat transfer coefficient, with the highest enhancement up to 252% at a Reynolds number of 1000 for MgO nanofluid. Our results demonstrated that these oxide nanofluids might be promising alternatives for conventional coolants.     

Numerical and Experimental Comparative Study on Nanofluids Flow and Heat Transfer in a Ribbed Triangular Duct

Numerical and experimental investigation is carried out to study the effect of combined vortex generator and nanofluids on turbulent heat transfer and fluid flow characteristics in an equilateral triangular duct. A triangular duct provides a lower heat transfer rate and lower pressure drop compared to other duct configurations. The improvement of heat transfer of these ducts increases their importance for providing higher heat transfer and lower pressure drop. Two different types of nanoparticles, namely Al₂O₃ and SiO₂, suspended in distilled water with two particle concentrations are successfully prepared and experimentally tested. The numerical and experimental results show dramatic heat transfer enhancement by using a vortex generator and nanofluids, simultaneously accomplished with a moderate increase in the friction factor. A low deviation has been seen between the present numerical and experimental results.     

Heat transfer enhancement of laminar nanofluids flow in a triangular duct using vortex generator

In this work, two dimensional laminar flow of different nanofluids flow inside a triangular duct with the existence of vortex generator is numerically investigated. The governing equations of mass, momentum and energy were solved using the finite volume method (FVM). The effects of type of the nanoparticles, particle concentrations, and Reynolds number on the heat transfer coefficient and pressure drop of nanofluids are examined. Reynolds number is ranged from 100 to 800. A constant surface temperature is assumed to be the thermal condition for the upper and lower heated walls. In the present work, three nanofluids are examined which are Al₂O₃, CuO and SiO₂ suspended in the base fluid of ethylene glycol with nanoparticles concentrations ranged from 1 to 6%. The results show that for the case of SiO₂–EG, at ? = 6% and Re = 800, it is found that the average Nusselt number is about 50.0% higher than the case of Re = 100.     

Phase change heat transfer of liquid nitrogen upon injection into aqueous based TiO<Subscript>2</Subscript> nanofluids

This paper reports an experimental study on the cryogenic phase change behaviour of liquid nitrogen upon injection into a relatively large pool of aqueous based titanium dioxide nanofluids under ambient temperatures. Stable TiO₂ are formulated at concentrations between 1% and 4% by particle weight, and characterized in the experiments. Both transient pressure and temperature profiles are measured and analysed in the range of liquid nitrogen Reynolds number of 2,200–11,000 and Webber number of 9–220. The results, however, do not show obvious influence of nanoparticles’ concentration on the pressure build up and heat transfer under the condition of this work. Very similar results are observed for liquid nitrogen injection into pure distilled water and into different concentrations of TiO₂ nanofluids; both the pressure and the rate of pressure rise during the injection process increase linearly with injection velocity irrespective of nanoparticle concentrations. Further discussion shows that a higher rate of pressure rise could be achieved if operating conditions were optimised to induce the fragmentation and subsequent vapour explosion.     

Studies on Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, CuO,and TiO<Subscript>2</Subscript> water-based nanofluids: A comparative approach in laminar and turbulent flow

The Prandtl number, Reynolds number and Nusselt number are functions of thermophysical properties of nanofluids, and these numbers strongly influence the convective heat transfer coefficient. The thermophysical properties vary with volumetric concentration of nanofluids. Therefore, a comprehensive analysis was performed to evaluate the effects on the performance of nanofluids due to variations of density, specific heat, thermal conductivity and viscosity, which are functions of nanoparticle volume concentration. Three metallic oxides, aluminum oxide (Al₂O₃), copper oxide (CuO), and titanium dioxide (TiO₂), dispersed in water as the base fluid were studied. A convenient figure of merit, known as the Mouromtseff number, is used as a base of comparisonfor laminar and turbulent flows. The results indicated that the considered nanofluids can successfully replace water in specific applications for a single-phase forced convection flow in a tube.     

Effect of Brownian motion on flow and heat transfer of nanofluids over a backward-facing step with and without adiabatic square cylinder

A mathematical model to predict large enhancement of thermal conductivity of nanofluids by considering the Brownian motion is proposed. The effect of the Brownian motion on the flow and heat transfer characteristics is examined. The computations were done for various types of nanoparticles such as CuO, Al₂O₃, and ZnO dispersed in a base fluid (water), volume fraction of nanoparticles ? in the range of 1 % to 6 % at a fixed Reynolds number Re = 450 and nanoparticle diameter d_np = 30 nm. Our results demonstrate that Brownian motion could be an important factor that enhances the thermal conductivity of nanofluids. Nanofluid of Al₂O₃ is observed to have the highest Nusselt number Nu among other nanofluids types, while nanofluid of ZnO nanoparticles has the lowest Nu. Effects of the square cylinder on heat transfer characteristics are significant with considering Brownian motion. Enhancement in the maximum value of Nu of 29 % and 26 % are obtained at the lower and the upper walls of the channel, respectively, by considering the Brownian effects, with square cylinder, compared with that in the case without considering the Brownian motion. On the other hand, results show a marked improvement in heat transfer compared to the base fluid, this improvement is more pronounced on the upper wall for higher ?.     

Natural convective heat transfer of Ag-water nanofluid flow inside enclosure with center heater and bottom heat source

A numerical study on natural convective heat transfer inside an enclosure with center heater using nanofluid has been carried out. The effect of different length of center heater on the flow and temperature fields is analysed for different Rayleigh numbers. Results are displayed in terms of streamlines, isotherms, mid height velocity profile and average Nusselt number. The numerical results reveal heat transfer increases with increasing heater length at both vertical and horizontal positions for increasing values of Rayleigh numbers. In particular, a higher increase in heat transfer is obtained with heater situated with vertical position of maximum length. Also it is obtained that enhancement of heat transfer is high for Ag - water nanofluid than CuO -water and Al₂O₃ -water nanofluids.     

The numerical investigation of heat transfer and pressure drop of turbulent flow in a triangular microchannel

In this presentation, the flow and heat transfer inside a microchannel with a triangular section, have been numerically simulated. In this three-dimensional simulation, the flow has been considered turbulent. In order to increase the heat transfer of the channel walls, the semi-truncated and semi-attached ribs have been placed inside the channel and the effect of forms and numbers of ribs has been studied. In this research, the base fluid is Water and the effect of volume fraction of Al₂O₃ nanoparticles on the amount of heat transfer and physics of flow have been investigated. The presented results are including of the distribution of Nusselt number in the channel, friction coefficient and Performance Evaluation Criterion of each different arrangement. The results indicate that, the ribs affect the physics of flow and their influence is absolutely related to Reynolds number of flow. Also, the investigation of the used semi-truncated and semi-attached ribs in Reynolds number indicates that, although heat transfer increases, but more pressure drop arises. Therefore, in this method, in order to improve the heat transfer from the walls of microchannel on the constant heat flux, using the pump is demanded.     

Experimental evaluation of friction factor and heat transfer enhancement of twisted tape inserts using TiO<Subscript>2</Subscript>–water nanofluids

This paper studies the experimental evaluation of TiO₂ nanofluids in enhancing the heat transfer rate and friction factor on a micro-finned tube fitted with twisted tape inserts. Results show that the enhancement in heat transfer and pumping power completely depends on the concentration ratio of nanoparticles, pitch ratio and the type of pitch. Comparisons were made with the previous study with different operating parameters such as twist ratio and twist type. Viscosity of nanofluid increases with an increase in the concentration, which leads to increased pressure drop and pumping power. For the Reynolds number (Re = 4000), the maximum performance ratio was found as 2.1, 2, for concentration of 0.1 and 0.05, respectively. The addition of microfin arrangement inside the circular tube enhanced the performance ratio with minimum concentration of TiO₂ nanofluid.     

纳米流体对流换热机理分析

考虑在纳米流体中纳米颗粒做布朗运动引起的对流换热, 基于纳米颗粒在纳米流体中遵循分形分布, 本文得到纳米流体对流换热的机理模型. 本解析模型没有增加新的经验常数, 从该模型发现纳米流体池沸腾热流密度是温度、纳米颗粒的平均直径、 纳米颗粒的浓度、纳米颗粒的分形维数、沸腾表面活化穴的分形维数、基本液体的物理特性的函数. 对不同的纳米颗粒浓度和不同的纳米颗粒平均直径与不同的实验数据进行了比较, 模型预测的结果与实验结果相吻合. 所得的解析模型可以更深刻地揭示纳米流体对流换热的物理机理.     

Experimental and numerical investigation of heat transfer in a miniature heat sink utilizing silica nanofluid

In this paper, heat transfer characteristics of a miniature heat sink cooled by SiO₂–water nanofluids were investigated both experimentally and numerically. The heat sink was fabricated from aluminum and insulated by plexiglass cover plates. The heat sink consisted of an array of 4 mm diameter circular channels with a length of 40 mm. Tests were performed while inserting a 180 W/cm² heat flux to the bottom of heat sink and Reynolds numbers ranged from 400 to 2000. The three-dimensional heat transfer characteristics of the heat sink were analyzed numerically by solving conjugate heat transfer problem of thermally and hydrodynamically developing fluid flow. Experimental results showed that dispersing SiO₂ nanoparticles in water significantly increased the overall heat transfer coefficient while thermal resistance of heat sink was decreased up to 10%. Numerical results revealed that channel diameter, as well as heat sink height and number of channels in a heat sink have significant effects on the maximum temperature of heat sink. Finally, an artificial neural network (ANN) was used to simulate the heat sink performance based on these parameters. It was found that the results of ANN are in excellent agreement with the mathematical simulation and cover a wider range for evaluation of heat sink performance.     

Influence of T-semi attached rib on turbulent flow and heat transfer parameters of a silver-water nanofluid with different volume fractions in a three-dimensional trapezoidal microchannel

This study aimed at exploring influence of T-semi attached rib on the turbulent flow and heat transfer parameters of a silver-water nanofluid with different volume fractions in a three-dimensional trapezoidal microchannel. For this purpose, convection heat transfer of the silver-water nanofluid in a ribbed microchannel was numerically studied under a constant heat flux on upper and lower walls as well as isolated side walls. Calculations were done for a range of Reynolds numbers between 10,000 and 16,000, and in four different sorts of serrations with proportion of rib width to hole of serration width (R/W). The results of this research are presented as the coefficient of friction, Nusselt number, heat transfer coefficient and thermal efficiency, four different R/W microchannels. The results of numerical modeling showed that the fluid's convection heat transfer coefficient is increased as the Reynolds number and volume fraction of solid nanoparticle are increased. For R/W=0.5, it was also maximum for all the volume fractions of nanoparticle and different Reynolds numbers in comparison to other similar R/W situations. That's while friction coefficient, pressure drop and pumping power is maximum for serration with R/W=0 compared to other serration ratios which lead to decreased fluid-heat transfer performance.     

Experimental Study of CuO/Water Nanofluid Turbulent Convective Heat Transfer in Square Cross-section Duct

Ducts with a square cross-section are widely used in many industrial applications because of their high compactness, easy forming, and low pressure drop. But the thermal performance of a duct will be reduced when the circular cross-sectional shape is not used. In this study, the convective heat transfer for a CuO/water nanofluid through a square cross-section duct in the turbulent flow regime has been investigated. The Nusselt number of nanofluids for different nanoparticle concentrations, as well as various Peclet numbers, was obtained. The results show considerable enhancement in the heat transfer coefficient and Nusselt number by increasing the nanoparticle concentrations as well as the Peclet number.     

Heat transfer behaviour of nanofluids in a uniformly heated circular tube fitted with helical inserts in laminar flow

The CFD simulation of heat transfer characteristics of a nanofluid in a circular tube fitted with helical twist inserts under constant heat flux has been explained using Fluent version 6.3.26 in laminar flow. Al₂O₃ nanoparticles in water of 0.5%, 1.0% and 1.5% concentrations and helical twist inserts of twist ratios 2.93, 3.91 and 4.89 has been used for the simulation. All thermophysical properties of nanofluids are temperature dependent. The heat transfer enhancement increases with Reynolds number and decreases with twist ratio with maximum for the twist ratio 2.93. By comparing the heat transfer rates of water and nanofluids, the increase in Nusselt number is 5%–31% for different helical inserts and different volume concentrations. The maximum heat transfer enhancement is 31.29% for helical insert of twist ratio 2.93 and for the volume concentration of 1.5% corresponding to the Reynolds number of 2039. The data obtained by simulation match with the literature value of water with the discrepancy of less than ±10% for plain tube and tube fitted with helical tape inserts for Nusselt number.     

Experimental investigation of heat transfer and friction coefficient of the water/graphene oxide nanofluid in a pipe containing twisted tape inserts under air cross-flow

The water/graphene oxide nanofluid effect in a pipe equipped by twisted tape inserts under air cross-flow is investigated and the optimal tape geometry is determined. The range of internal and external Reynolds numbers are: 3800<Re_o<21500 and 550<Re_i<2000. Heat transfer and pressure drop increase by increasing Re and inserts width and heat transfer performance coefficient increased up to 1.4, indicating enhanced heat transfer compared to undesirable pressure drop. On the other hand, the heat transfer coefficient is 26% higher when compared with water in a plain tube. According to the results, this method is a good alternative in heat exchangers.     

Analytical prediction of forced convective heat transfer of fluids embedded with nanostructured materials (nanofluids)

Nanofluids are a new class of heat transfer fluids developed by suspending nanosized solid particles in liquids. Larger thermal conductivity of solid particles compared to the base fluid such as water, ethylene glycol, engine oil etc. significantly enhances their thermal properties. Several phenomenological models have been proposed to explain the anomalous heat transfer enhancement in nanofluids. This paper presents a systematic literature survey to exploit the characteristics of nanofluids, viz., thermal conductivity, specific heat and other thermal properties. An empirical correlation for the thermal conductivity of Al₂O₃ + water and Cu + water nanofluids, considering the effects of temperature, volume fraction and size of the nanoparticle is developed and presented. A correlation for the evaluation of Nusselt number is also developed and presented and compared in graphical form. This enhanced thermophysical and heat transfer characteristics make fluids embedded with nanomaterials as excellent candidates for future applications.      

Convective Heat Transfer of a Cu/Water Nanofluid Flowing Through a Circular Tube

Abstract

Fluids in which nanometer-sized solid particles are suspended are called nanofluids. These fluids can be employed to increase the heat transfer rate in various applications. In this study, the convective heat transfer for Cu/water nanofluid through a circular tube was experimentally investigated. The flow was laminar, and constant wall temperature was used as thermal boundary condition. The Nusselt number of nanofluids for different nanoparticle concentrations, as well as various Peclet numbers, was obtained. Also, the rheological properties of the nanofluid for different volume fractions of nanoparticles were measured and compared with theoretical models. The results show that the heat transfer coefficient is enhanced by increasing the nanoparticle concentrations as well as the Peclet number.     

Heat transfer enhancement by application of nano-powder

In this investigation, laminar flow heat transfer enhancement in circular tube utilizing different nanofluids including Al₂O₃ (20 nm), CuO (50 nm), and Cu (25 nm) nanoparticles in water was studied. Constant wall temperature was used as thermal boundary condition. The results indicate enhancement of heat transfer with increasing nanoparticle concentrations, but an optimum concentration for each nanofluid suspension can be found. Based on the experimental results, metallic nanoparticles show better enhancement of heat transfer coefficient in comparison with oxide particles. The promotions of heat transfer due to utilizing nanoparticles are higher than the theoretical correlation prediction.     

Experiments to Explore the Mechanisms of Heat Transfer in Nanocrystalline Alumina/Water Nanofluid under Laminar and Turbulent Flow Conditions

Abstract

Heat transfer characteristics of water-based nanocrystalline alumina (Al₂O₃) nanofluids flowing through a uniformly heated tube under a fully developed laminar and turbulent flow regime is investigated experimentally in the present work to explore the heat transfer mechanism in nanofluids. In a laminar flow, the increase in Nusselt number was attributed to the thermophysical properties of the nanofluid. The movement of nanoparticles, along with the turbulent eddies in the turbulent core region and diffusion mechanism, such as thermophoresis, in the laminar sublayer are believed to be the reasons for enhanced heat transfer in turbulent region. The compatibility of Al₂O₃/water nanofluids was also examined by monitoring its color.