Performance,emission and combustion characteristics of a variable compression ratio engine using methyl esters of waste cooking oil and diesel blends

The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with waste cooking oil methyl ester and its 20%, 40%, 60% and 80% blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of waste cooking oil methyl ester as a biofuel has been established in this study. Bio diesel produced from waste sun flower oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 18:1, 19:1, 20:1, 21:1 and 22:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for waste cooking oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.     

Effect of metal based additive on performance emission and combustion characteristics of diesel engine fuelled with biodiesel

This study investigates the use of ferric chloride (FeCl₃) as a fuel borne catalyst (FBC) for waste cooking palm oil based biodiesel. The metal based additive was added to biodiesel at a dosage of 20 μmol/L. Experiments were conducted to study the effect of ferric chloride added to biodiesel on performance, emission and combustion characteristics of a direct injection diesel engine operated at a constant speed of 1500 rpm at different operating conditions. The results revealed that the FBC added biodiesel resulted in a decreased brake specific fuel consumption (BSFC) of 8.6% while the brake thermal efficiency increased by 6.3%. FBC added biodiesel showed lower nitric oxide (NO) emission and slightly higher carbon dioxide (CO₂) emission as compared to diesel. Carbon monoxide (CO), total hydrocarbon (THC) and smoke emission of FBC added biodiesel decreased by 52.6%, 26.6% and 6.9% respectively compared to biodiesel without FBC at an optimum operating condition of 280 bar injection pressure and 25.5^o bTDC injection timing. Higher cylinder gas pressure, heat release rate and shorter ignition delay period were observed with FBC added biodiesel at these conditions.     

Effect of injection parameters on the combustion and emission characteristics in a common-rail direct injection diesel engine fueled with waste cooking oil biodiesel

The objective of this paper was to study the effects of the injection pressure and injection timing on the combustion and emission characteristics in a single-cylinder common-rail direct injection (CRDI) diesel engine fueled with waste cooking oil (WCO) biodiesel and commercial diesel fuel. The fuel property including fatty acid composition for the biodiesel were measured and compared with those of the conventional diesel fuel. The engine tests were conducted at two injection pressures (80 and 160 MPa) and different injection timings from −25 to 0 crank angle degree (CAD) after top dead center (aTDC) under two different engine loads. The results showed that the indicated specific fuel consumption (ISFC) with respect to the injection timings of the biodiesel was higher than that of the diesel fuel under all experimental conditions. The peak cylinder pressure and the peak heat release rate of the biodiesel were slightly lower, while the ignition delay was slightly longer under all operating conditions. In terms of emissions, the biodiesel had benefits in reduction of smoke, carbon monoxide (CO), hydrocarbon (HC) emissions especially with high fuel injection pressure. The nitrogen oxide (NO_x) emissions of the biodiesel were relatively higher than those of the diesel under all experimental conditions.     

Biodiesel production from waste cooking oil using heterogeneous catalysts and its operational characteristics on variable compression ratio CI engine

In the present work, the optimum biodiesel conversion from waste cooking oil to biodiesel through transesterification method was investigated. The base catalyzed transesterification under different reactant proportions such as the molar ratio of alcohol to oil and mass ratio of catalyst to oil was studied for optimum production of biodiesel. The optimum condition for base catalyzed transesterification of waste cooking oil was determined to be 12:1 and 5 wt% of zinc doped calcium oxide. The fuel properties of the produced biodiesel such as the calorific value, flash point and density were examined and compared to conventional diesel. The properties of produced biodiesel and their blend for different ratios (B20, B40, B60, B80 and B100) were comparable with properties of diesel oil and ASTM biodiesel standards. Tests have been conducted on CI engine which runs at a constant speed of 1500 rpm, injection pressure of 200 bar, compression ratio 15:1 and 17.5, and varying engine load. The performance parameters include brake thermal efficiency, brake specific energy consumption and emissions parameters such as Carbon monoxide (CO), Hydrocarbon (HC), Oxides of Nitrogen (NOx) and smoke opacity varying with engine load (BP). Diesel engine's thermal performance and emission parameters such as CO, HC, and NOx on different biodiesel blends demonstrate that biodiesel produced from waste cooking oil using heterogeneous catalyst was suitable to be used as diesel oil blends and had lesser emissions as compared to conventional diesel.     

Study of performance,combustion, and NOx emission behavior of an SI engine fuelled with ammonia/hydrogen blends at various compression ratio

In the present paper, an experimental investigation has been performed under variable CR and 1400&1800RPM speed at a fixed spark timing of 24ºCA BTDC under wide-open throttle conditions. The hydrogen blending is performed based on energy fractions from 5% to 21% of the total fuel energy. With increasing compression ratio (CR), the flame development gets faster, and the flame propagation speed improves, leading to a short combustion period. Similarly, increasing hydrogen fraction improves combustion, resulting in a rapid rise in pressure and temperature. Despite a 13.64% decrease in volumetric efficiency from 5% to 21% hydrogen fraction at 1400 and 1800 RPM, BP and BTE increased by 16.89% and 33%, respectively. The slow-burning properties of NH₃ extend the combustion period, resulting in a long-delayed burning period. As a result, the temperature of the low-hydrogen fraction of the exhaust gas is higher. As the hydrogen fraction and CR increase, this effect decreases, resulting in lower EGT. The hydrogen addition increases the peak temperature; therefore, NO_x increases continuously with increasing hydrogen despite reducing ammonia. Ammonia is a key element used to reduce NO_x from vehicles. A practical solution for controlling the NO_x due to the ammonia/hydrogen blend is selective catalytic reduction (SCR).     

Hydrogen enriched waste oil biodiesel usage in compression ignition engine

In the present study, hydrogen enrichment for biodiesel-diesel blends was evaluated to investigate the performance and emission characteristics of a compression ignition engine. Biodiesel was obtained from waste oil and blended to pure diesel fuel by volume fraction of 0%, 10% and 20%. After that, pure hydrogen was introduced through the intake air at different flow rates. Effects of pure hydrogen on performance and emission characteristics were investigated by evaluating power, torque, specific fuel consumption, CO, CO₂ and NO_x emissions. Experimental study revealed that waste oil biodiesel usage deteriorated performance and emission parameters except CO emissions. However, the enrichment test fuels with hydrogen fuel can improve performance characteristics and emission parameters, whereas it increased NO_x emissions. Brake thermal efficiency and specific fuel consumption were improved when the test fuels enriched with hydrogen gas. Because of absence of carbon atoms in the chemical structure of the hydrogen fuel, hydrogen addition dropped CO and CO₂ emissions but increment in cylinder temperature caused rising in NO_x emissions.     

A comprehensive study on performance,emission and combustion behavior of a compression ignition engine fuelled with WCO (waste cooking oil) emulsion as fuel

This work aims at evaluating the performance, emission and combustion of a diesel engine fuelled with WCO (waste cooking oil obtained from palm oil) and its emulsion as fuel. A single cylinder water-cooled diesel engine was used. Base data was generated with diesel and neat WCO as fuels. Subsequently, WCO oil was converted into its emulsion and tested. Neat WCO resulted in higher smoke, hydrocarbon and carbon monoxide emissions as compared to neat diesel. Significant reduction in all emission was achieved with the WCO emulsion. Cylinder peak pressure and maximum rate of pressure rise were found to be higher with WCO emulsion as compared to neat WCO mainly at high power outputs. Ignition delay was found as higher with neat WCO and its emulsion. It is concluded that WCO emulsion can be used in diesel engines without any modifications in the engine with superior performance and reduced emissions at high power outputs.     

Influence of injection timing on performance,combustion and emission characteristics of Jatropha biodiesel engine

The study of effect of injection timing along with engine operating parameters in Jatropha biodiesel engine is important as they significantly affect its performance and emissions. The present paper focuses on the experimental investigation of the influence of injection timing, load torque and engine speed on the performance, combustion and emission characteristics of Jatropha biodiesel engine. For this purpose, the experiments were conducted using full factorial design consisting of (3³) with 27 runs for each fuel, diesel and Jatropha biodiesel. The effect of variation of above three parameters on brake specific fuel consumption (BSFC), brake thermal efficiency (BTE), peak cylinder pressure (P_max), maximum heat release rate (HRR_max), CO, HC, NO emissions and smoke density were investigated. It has been observed that advance in injection timing from factory settings caused reduction in BSFC, CO, HC and smoke levels and increase in BTE, P_max, HRR_max and NO emission with Jatropha biodiesel operation. However, retarded injection timing caused effects in the other way. At 15 N m load torque, 1800 rpm engine speed and 340 crank angle degree (CAD) injection timing, the percentage reduction in BSFC, CO, HC and smoke levels were 5.1%, 2.5%, 1.2% and 1.5% respectively. Similarly the percentage increase in BTE, P_max, HRR_max and NO emission at this injection timing, load and speed were 5.3%, 1.8%, 26% and 20% respectively. The best injection timing for Jatropha biodiesel operation with minimum BSFC, CO, HC and smoke and with maximum BTE, P_max, HRR_max is found to be 340 CAD. Nevertheless, minimum NO emission yielded an optimum injection timing of 350 CAD.     

Influence of injection timing on performance, emission and combustion characteristics of a DI diesel engine running on waste plastic oil

Environmental concern and availability of petroleum fuels have caused interests in the search for alternate fuels for internal combustion engines. Waste plastics are indispensable materials in the modern world and application in the industrial field is continually increasing. In this context, waste plastics are currently receiving renewed interest. As an alternative, non-biodegradable, and renewable fuel, waste plastic oil is receiving increasing attention. The waste plastic oil was compared with the petroleum products and found that it can also be used as fuel in compression ignition engines. In the present work, the influence of injection timing on the performance, emission and combustion characteristics of a single cylinder, four stroke, direct injection diesel engine has been experimentally investigated using waste plastic oil as a fuel. Tests were performed at four injection timings (23°,20°,17° and 14° bTDC). When compared to the standard injection timing of 23° BTDC the retarded injection timing of 14° bTDC resulted in decreased oxides of nitrogen, carbon monoxide and unburned hydrocarbon while the brake thermal efficiency, carbon dioxide and smoke increased under all the test conditions.     

Performance,combustion and exhaust emissions characteristics investigation using Citrullus colocynthis L. biodiesel in DI diesel engine

The aims of this study is to investigate the performance, combustion and exhaust emissions of a single-cylinder, air cooled, direct injection (DI), compression ignition engine using biodiesel from non-edible feedstock. In this work, biodiesel (B100) used to lead this investigation is Citrullus colocynthis L. methyl ester (CCME) and its blends B30 with diesel fuel. The biodiesel is produced via alkaline-catalyzed transesterification process using methanol (6:1 M ratio), 1% of sodium hydroxide at the reaction temperature of 60 °C for 1 h. The important physical and chemical properties of CCME are close to those of diesel fuel. Fuels (diesel fuel, B100 and B30) were tested on a DI diesel engine at 1500 rpm for various power outputs. The results indicated that B100 and B30 exhibit the same combustion characteristics compared to diesel fuel. However, B100 and B30 display earlier start of combustion. At lower engine loads, the peaks of cylinder pressure and heat release rate (HRR) were higher for B30 than B100 and diesel fuel during premixed combustion period. At higher engine loads the peaks of cylinder pressure was higher for B100 than B30 and diesel fuel, but the HRR during diffusion combustion is more considerable than diesel fuel. The brake specific fuel consumption (BSFC) was higher for B100 than diesel fuel at all engine loads while B30 exhibited comparable trends. The thermal efficiency is slightly higher for B100 than B30 and diesel fuel at low loads and increase for B30 at full loads.B30 and B100 provided a higher reduction of hydrocarbons emissions up to 50% for B100. Nitrogen oxides and particulate matter emissions were also reduced.     

Effects of oxyhydrogen on the CI engine fueled with the biodiesel blends: A performance,combustion and emission characteristics study

The main purpose of this study is to analyse the effects of oxy hydrogen (HHO) along with the Moringa oleifera biodiesel blend on engine performance, combustion and emission characteristics. HHO gases were generated using the typical electrolysis process using the potassium hydroxide solution. The experiments were performed under various engine loads of 25%, 50%, 75%, and 100% in a constant speed engine. Biodiesel from the M. oleifera was prepared by the transesterification process. Further, the procured biodiesel blends mixed with neat diesel at the concentration of 20% (B20) and 40% (B40). In addition to above, the HHO gas flow rate to the engine chamber maintained at the flow rate of 0.5 L^-1. The use of the 20% and 40% blends with HHO reported less BTE compared to the neat diesel. However, B20 reported marginal rise in the BTE due to the addition of the HHO gas. On the other hand, addition of HHO gas to the blends significantly dropped the brake specific fuel consumption. With regard to the emissions, addition of the biodiesel blends reduced the concentration of the CO, HC, and CO₂. Nevertheless, no reduction reported in the formation of the NO. However, adding the HHO to the biodiesel reduced the average NOx by 6%, which is a substantial effect. Overall, HHO enriching biodiesel blends are the potential replacement for the existing fossil fuels for its superior fuel properties compared to the conventional diesel.     

Artificial Neural Network based prediction of performance and emission characteristics of a variable compression ratio CI engine using WCO as a biodiesel at different injection timings

Due to the increasing demand for fossil fuels and environmental threat due to pollution a number renewable sources of energy have been studied worldwide. In the present investigation influence of injection timing on the performance and emissions of a single cylinder, four stroke stationary, variable compression ratio, diesel engine was studied using waste cooking oil (WCO) as the biodiesel blended with diesel. The tests were performed at three different injection timings (24°, 27°, 30° CA BTDC) by changing the thickness of the advance shim. The experimental results showed that brake thermal efficiency for the advanced as well as the retarded injection timing was lesser than that for the normal injection timing (27° BTDC) for all sets of compression ratios. Smoke, un-burnt hydrocarbon (UBHC) emissions were reduced for advanced injection timings where as NO_x emissions increased. Artificial Neural Networks (ANN) was used to predict the engine performance and emission characteristics of the engine. Separate models were developed for performance parameters as well as emission characteristics. To train the network, compression ratio, injection timing, blend percentage, percentage load, were used as the input parameters where as engine performance parameters like brake thermal efficiency (BTE), brake specific energy consumption (BSEC), exhaust gas temperature (T_exh) were used as the output parameters for the performance model and engine exhaust emissions such as NO_x, smoke and (UBHC) values were used as the output parameters for the emission model. ANN results showed that there is a good correlation between the ANN predicted values and the experimental values for various engine performance parameters and exhaust emission characteristics and the relative mean error values (MRE) were within 8%, which is acceptable.     

Experimental study of the effects of excess air ratio on combustion and emission characteristics of the hydrogen-fueled rotary engine

To investigate the property of the promising and eco-friendly hydrogen-fueled rotary engine, the effect of excess air ratio on the combustion and emission characteristic of it was explored by experiment. The test was conducted under 1500 rpm and 5 CAD ADTC ignition timing. The test results demonstrated that with the decrease of excess air ratio from 2 to 0.85, the thermal efficiency of the hydrogen-fueled rotary engine increases first and then decreases. Besides, increasing MAP is beneficial to improve thermal efficiency. Among the tested condition, the highest brake thermal efficiency is realized when the rotary engine operates at 1.4 excess air ratio and 88 kPa MAP, about 18.34%. And the excellent HC and NO emissions can be obtained at the highest efficiency point. Besides, with the decrease of excess air ratio and the increase of load, the stability and flame development period gradually decrease. With a decreased excess air ratio, the flame propagation period decrease first and then increases, whereas work capacity and thermal efficiency increase first and then decrease. For NO emission, it will increase sharply near the equivalent ratio and gradually decrease after rich combustion. Also, according to the analytical model, it is found that the power performance of the rotary engine depends on the trade-off relationship of in-cylinder pressure and its angle of action.     

Experimental study of combustion and emission characteristics of ethanol fuelled port injected homogeneous charge compression ignition (HCCI) combustion engine

The homogeneous charge compression ignition (HCCI) is an alternative combustion concept for in reciprocating engines. The HCCI combustion engine offers significant benefits in terms of its high efficiency and ultra low emissions. In this investigation, port injection technique is used for preparing homogeneous charge. The combustion and emission characteristics of a HCCI engine fuelled with ethanol were investigated on a modified two-cylinder, four-stroke engine. The experiment is conducted with varying intake air temperature (120–150 °C) and at different air–fuel ratios, for which stable HCCI combustion is achieved. In-cylinder pressure, heat release analysis and exhaust emission measurements were employed for combustion diagnostics. In this study, effect of intake air temperature on combustion parameters, thermal efficiency, combustion efficiency and emissions in HCCI combustion engine is analyzed and discussed in detail. The experimental results indicate that the air–fuel ratio and intake air temperature have significant effect on the maximum in-cylinder pressure and its position, gas exchange efficiency, thermal efficiency, combustion efficiency, maximum rate of pressure rise and the heat release rate. Results show that for all stable operation points, NO_x emissions are lower than 10 ppm however HC and CO emissions are higher.     

Effects of compression ratio on performance and emission characteristics of heavy-duty SI engine fuelled with HCNG

The wide range of hydrogen's flammable limits enables ultra-lean combustion. A lean burn reduces the combustion temperature, increases thermal efficiency, and reduces knock, which is a serious problem in a spark ignition (SI) engine. The anti-knock improvement from hydrogen addition makes it feasible to increase the compression ratio (CR) and further improve the thermal efficiency. Herein, the effects of the CR on performance and emission characteristics were investigated using an 11-L heavy-duty SI engine fuelled with HCNG30 (CNG 70 vol%, hydrogen 30 vol%) and CNG. These fuels were used to operate an engine with CRs of 10.5 and 11.5. The results showed that thermal efficiency improved with an increased CR, which significantly decreased CO₂ emission. On the other hand, the NO_x emission was largely increased. Nevertheless, for HCNG30, a CR of 11.5 improved thermal efficiency by 6.5% and decreased NO_x emission by over 75%, as compared to a conventional CNG engine.     

A review of the effects of catalyst and additive on biodiesel production, performance, combustion and emission characteristics

This article is a literature review of the effect of different catalysts and additives on biodiesel production, performance, combustion and emission characteristics. This study is based on the reports of about 60 scientists who published their findings between 1998 and 2010. It was reported that base catalyst produced more biodiesel compared to acid type catalysts. There was not much variation in engine performance with the use of catalyst. Combustion characteristics were improved with the use of additives. It was found that ignition delay was reduced and premixed combustion duration was increased with the addition of catalyst. HC emission and PM emission were reduced with the use of catalysts.     

An experimental study on performance and emission characteristics of a hydrogen fuelled spark ignition engine

In the present paper, the performance and emission characteristics of a conventional four cylinder spark ignition (SI) engine operated on hydrogen and gasoline are investigated experimentally. The compressed hydrogen at 20  MPa has been introduced to the engine adopted to operate on gaseous hydrogen by external mixing. Two regulators have been used to drop the pressure first to 300 kPa, then to atmospheric pressure. The variations of torque, power, brake thermal efficiency, brake mean effective pressure, exhaust gas temperature, and emissions of _NOx${\mathrm{NO}}_x$, CO, _CO2${\mathrm{CO}}_2$, HC, and _O2${\mathrm{O}}_2$ versus engine speed are compared for a carbureted SI engine operating on gasoline and hydrogen. Energy analysis also has studied for comparison purpose. The test results have been demonstrated that power loss occurs at low speed hydrogen operation whereas high speed characteristics compete well with gasoline operation. Fast burning characteristics of hydrogen have permitted high speed engine operation. Less heat loss has occurred for hydrogen than gasoline. _NOx${\mathrm{NO}}_x$ emission of hydrogen fuelled engine is about 10 times lower than gasoline fuelled engine. Finally, both first and second law efficiencies have improved with hydrogen fuelled engine compared to gasoline engine. It has been proved that hydrogen is a very good candidate as an engine fuel. The obtained data are also very useful for operational changes needed to optimize the hydrogen fueled SI engine design.     

Evaluating combustion,performance and emission characteristics of diesel engine using karanja oil methyl ester biodiesel blends enriched with HHO gas

With a specific end goal to take care of the worldwide demand for energy, a broad research is done to create alternative and cost effective fuel. The fundamental goal of this examination is to investigate the combustion, performance and emission characteristics of diesel engine using biodiesel blends enriched with HHO gas. The biodiesel blends are gotten by blending KOME obtained from transesterification of karanja oil in various proportions with neat diesel. The HHO gas is produced by the electrolysis of water in the presence of sodium bicarbonate electrolyte. The constant flow of HHO gas accompanied with biodiesel guarantees lessened brake specific fuel consumption by 2.41% at no load and 17.53% at full load with increased the brake thermal efficiency by 2.61% at no load and 21.67% at full load contrasted with neat diesel operation. Noteworthy decline in unburned hydrocarbon, carbon monoxide, carbon-dioxide emissions and particulate matter with the exception of NO_x discharge is encountered. The addition of EGR controls this hike in NO_x with a slight decline in the performance characteristics. It is clear that the addition of HHO gas with biodiesel blends along with EGR in the test engine improved the overall characterization of engine.     

Preparation,characterization, engine combustion and emission characteristics of rapeseed oil based hybrid fuels

In this study, hybrid fuels consisting of rapeseed oil/diesel blend, 1% aqueous ethanol and a surfactant (oleic acid/1-butanol mixture) were prepared and tested as a fuel in a direct injection (DI) diesel engine. The main fuel properties such as the density, viscosity and lower heating value (LHV) of these fuels were measured, and the engine performance, combustion and exhaust emissions were investigated and compared with that of diesel fuel. The experimental results showed that the viscosity and density of the hybrid fuels were decreased and close to that of diesel fuel with the increase of ethanol volume fraction up to 30%. The start of combustion was later than that of diesel fuel and the peak cylinder pressure, peak pressure rise rate and peak heat release rate were higher than those of diesel fuel. The brake specific fuel consumption (BSFC) of hybrid fuels was increased with the volume fraction of ethanol and higher than that of diesel. The brake specific energy consumption (BSEC) was almost identical for all test fuels. The smoke emissions were lower than those for diesel fuel at high engine loads, the NO_x emissions were almost similar to those of diesel fuel, but CO and HC emissions were higher, especially at low engine loads.     

Studies on the effect of hydrogen induction on performance,emission and combustion behaviour of a WCO emulsion based dual fuel engine

This paper aims at studying the effect of hydrogen induction on engine performance, emission and combustion behaviour of a diesel engine fuelled with the emulsion of used palm oil (called as WCO-waste cooking oil) as pilot fuel and hydrogen as primary fuel. A single cylinder water-cooled direct injection diesel engine was tested at 100% and 40% loads. Results were compared with neat diesel, neat WCO and WCO emulsion at both loads in single fuel operation. WCO emulsion in single fuel mode indicated improvement in performance and reduction in all emissions as compared to neat WCO. Dual fuel operation with hydrogen induction further reduced the emissions of smoke HC and CO with WCO as pilot fuel at all power outputs. However, hydrogen induction resulted in reduced thermal efficiency at 40% load. WCO emulsion showed higher ignition delay as compared to neat WCO. Dual fuel operation with hydrogen induction increased the ignition delay further. Heat release pattern showed higher premixed combustion rate with hydrogen induction mainly at high power outputs. Premixed combustion rate became very high at higher rates of hydrogen admission mainly at high power output. In general, hydrogen induction showed superior performance at high power output and inferior performance at low power output with WCO emulsion as injected fuel.