Al2O3-coated SnO2/TiO2 composite electrode for the dye-sensitized solar cell

A novel Al₂O₃-coated SnO₂/TiO₂ composite electrode has been applied to the dye-sensitized solar cell. In such an electrode, two kinds of energy barriers (SnO₂/TiO₂ and TiO₂/Al₂O₃) were designed to suppress the recombination processes of the photo-generated electrons and holes. After the SnO₂ was modified by colloid TiO₂, the photoelectric conversion efficiency of the SnO₂/TiO₂ composite cell increased to 2.08% by a factor of 2.8 comparing with that of the SnO₂ cell. The Al₂O₃ layer on the SnO₂/TiO₂ composite electrode further suppressed the generation of the dark current, resulting in 37% improvement in device performance comparing with the SnO₂/TiO₂ cell.     

TiO2/modified natural clay semiconductor as a potential electrode for natural dye-sensitized solar cell

TiO₂/modified natural bentonite clay semiconductor, as a potential electrode of dye-sensitized solar cell, having a Ti:Si molar ratio of 85:15 was, for the first time, compared with pure TiO₂ (commercial P25) electrode in terms of solar cell efficiency and characteristics. 4-Chloro-2,5-difluorobenzoic acid and 4-(chloromethyl)benzoyl chloride were added to the electrodes to increase light harvesting ability of natural dyes extracted from red cabbage, rosella, and blue pea. The results showed that the TiO₂/clay semiconductor provided a higher surface area but a slightly lower efficiency than the pure TiO₂. The best natural sensitizer was found to be the dye extracted from red cabbage. Besides, the 4-(chloromethyl)benzoyl chloride provided a higher short circuit current for the TiO₂/clay semiconductor.     

A novel hierarchical Pt- and FTO-free counter electrode for dye-sensitized solar cell

A novel hierarchical Pt- and FTO-free counter electrode (CE) for the dye-sensitized solar cell (DSSC) was prepared by spin coating the mixture of TiO₂ nanoparticles and poly(3,4-ethylenedioxy-thiophene):poly(styrenesulfonate) (PEDOT:PSS) solution onto the glass substrate. Compared with traditional Pt/FTO CE, the cost of the new CE is dramatically reduced by the application of bilayer TiO₂-PEDOT:PSS/PEDOT:PSS film and the glass substrate. The sheet resistance of this composite film is 35 Ω sq⁻¹ and is low enough to be used as an electrode. The surface morphologies of TiO₂-PEDOT:PSS layer and modified PEDOT:PSS layer were characterized by scanning electron microscope, which shows that the former had larger surface areas than the latter. Electrochemical impedance spectra and Tafel polarization curves prove that the catalytic activity of TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE is higher than that of PEDOT:PSS/FTO CE and is similar to Pt/FTO CE''s. This new fabricated device with TiO₂-PEDOT:PSS/PEDOT:PSS/glass CE achieves a high power conversion efficiency (PCE) of 4.67%, reaching 91.39% of DSSC with Pt/FTO CE (5.11%).     

Cationic surfactant promoted reductive electrodeposition of nanocrystalline anatase TiO2 for application to dye-sensitized solar cells

A new strategy involving the introduction of the common cationic surfactant cetyltrimethylammonium bromide (CTAB) for the cathodic deposition of titanium dioxide from hydrolyzed TiCl₄ and TiCl₃ solutions by cyclic voltammetry has been developed. Crack-free and non-transparent anatase TiO₂ films were obtained for the first time and characterized with the aid of Raman spectra and SEM. Selection of TiCl₄ as the precursor for the electrodeposition is quite a novel approach for the research in the area of dye-sensitized solar cells (DSSCs). It is noted that NO₃⁻ ion is essential for such a deposition. Under the same conditions, a thicker TiO₂ film was obtained by adding CTAB into KNO₃ electrolyte, compared with the case without it. The CTAB-promoted film led to an increased energy conversion efficiency of the corresponding DSSC. Mechanisms are proposed for the electrochemical deposition and the beneficial role of CTAB.     

A composite poly(3,3-diethyl-3,4-dihydro-2H-thieno-[3,4-b][1,4]-dioxepine) and Pt film as a counter electrode catalyst in dye-sensitized solar cells

A composite poly(3,3-diethyl-3,4-dihydro-2H-thieno-[3,4-b][1,4]-dioxepine) and platinum (PProDOT-Et₂/Pt) film was prepared for using as a counter electrode (CE) catalyst in a dye-sensitized solar cell (DSSC). Four composite films were prepared by electropolymerization of ProDOT-Et₂ on indium tin oxide (ITO) conducting glass, followed by Pt sputtering for 10, 30, 120, and 720 s. The Pt content in the composite film was verified by energy dispersive X-ray spectroscopy (EDX). The composite films possessed three-dimensional (3D) porous structures, as determined by scanning electron microscopy (SEM). The DSSC with the composite film that was subject to 10 s of Pt deposition (PProDOT-Et₂/Pt-10 s) exhibited the highest solar to electricity conversion efficiency (η) of 6.68%, while the cells with the bare polymer film (PProDOT-Et₂) and Pt that was sputtered for 720 s (s-Pt-720 s) demonstrated efficiencies of 4.76% and 6.43%, respectively. The cell photovoltaic parameters were substantiated through dark current, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS) analyses. Incident photon-to-current conversion efficiency (IPCE) curves were used to explain the cell photocurrent behaviors.     

Synthesis of Zn-doped TiO2 microspheres with enhanced photovoltaic performance and application for dye-sensitized solar cells

Zn-doped TiO₂ microspheres have been synthesized by introducing a trace amount of zinc nitrate hexahydrate to the reaction system. Scanning electron microscope (SEM), field-emission scanning electron microscope (FESEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS) have been utilized to characterize the samples. Both surface photovoltage spectroscopy (SPS) technique based on lock-in amplifier and transient photovoltage (TPV) measurement reveal that the slight doping of Zn can promote the separation of photo-generated charges as well as restrain the recombination due to the strong interface built-in electric field and the decreasing of surface trap states. The photovoltaic parameters of dye-sensitized solar cells (DSSCs) based on Zn-doped TiO₂ are significantly better, compared to that of a cell based on undoped TiO₂. The relation between the performance of DSSCs and their photovoltaic properties is also discussed.     

Quasi solid state dye-sensitized solar cells with modified TiO2 photoelectrodes and triphenylamine-based dye

Quasi solid state dye-sensitized solar cells (DSSCs) have been fabricated with organic sol or TiCl₄ modified TiO₂ and porous TiO₂ photoanode and a triphenylamine-based dye (TPAR3) used as photosensitizer. Dark current measurements suggested that both modified TiO₂ photoelectrodes had significantly reduced the recombination rate of photoelectrons due to the reduced bare FTO surface in comparison to porous photoelectrode. The DSSC based on modified TiO₂ photoelectrodes showed improved photovoltaic parameters compared to the porous TiO₂ photoelectrode. The overall power conversion efficiency (PCE) is 3.27%, 4.73% and 6.8% for porous, TiCl₄ modified and sol modified TiO₂ photoelectrodes, respectively. The improved PCE with modified TiO₂ electrodes was attributed to the formation of a compact layer. This effectively improves adherence of TiO₂ to FTO surface, providing a larger TiO₂/FTO contact area and reducing the electron recombination by blocking the direct contact between redox electrolyte and the conductive FTO surface and enhances the electron collection efficiency.     

Role of surface state on the electron flow in modified TiO2 film incorporating carbon powder for a dye-sensitized solar cell

An investigation of surface-related traps in nanostructured TiO₂ films modified by the incorporation of carbon powder was conducted by the potential-step chronoamperometric method. For the modification of the morphology and surface state of the nanoporous TiO₂ electrode, the incorporation of carbon into the white TiO₂ powder was accomplished. In the chronoamperometric data, all of the transients showed an initial fast phase (<1 s) followed by a slower phase which is related to the trap filling process. The trap-filling period of the carbon incorporated TiO₂ film becomes longer, as the applied negative potential increases, due to the widely distributed traps induced by the increased surface area. Furthermore, the film capacitance was derived as a function of the applied bias by integrating the current to time curves of the chronoamperometric data. The accumulated charge of the carbon incorporated TiO₂ film increases prominently in two regions. The dominant increase shown in the positive region (−0.7 to −0.9 V vs. Ag/AgCl at pH 13) of the flat band potential implies that the electron occupancy in the surface-related traps is increased. At a more negative potential (below −1.2 V vs. Ag/AgCl), electrons from the conduction band of the TiO₂ film substantially influence the total current, thereby inducing an exponential increase in the current. Therefore, it is found that most of the traps are located in the positive region of the flat band potential, since the Fermi level of the nanostructured TiO₂ film is positioned at −1.14 V vs. Ag/AgCl at pH 13. The trap sites in the sub-bandgap region of the TiO₂ film are important in the electron transport of photoinjected electrons from dye molecules and partially charge recombination with redox electrolyte in operating dye-sensitized solar cell. The influence of charge trap formed by increased surface states on the electron transport and electron transfer was investigated by photovoltage and photocurrent transient measurements.     

Fluorescence spectra of poly(di-n-hexylsilane)/TiO2 nanoparticle hybrid film

The interaction between poly(di-n-hexylsilane) (PDHS) and TiO₂ nanoparticle was studied based on the temperature dependence of the fluorescence of a PDHS/TiO₂ nanoparticle hybrid film. The polysilane is a suitable probe to investigate a guest polymer-host matrix interaction because the photophysical properties of polysilanes remarkably depend on the conformation of the σ-conjugated Si-Si chain. The PDHS/TiO₂ nanoparticle hybrid film showed a fluorescence band assigned to a disordered structure even at 80 K whereas only the fluorescence band of an ordered structure was observed for the PDHS film at 80 K. The disordering of the Si-Si main chain was explained by the perturbation of the n-hexyl side chain in the neighborhood of the TiO₂ nanosurface. The non-radiative deactivation of the excited state via the disorder-induced local potential minima was suggested by the temperature dependence of the fluorescence intensities of the disordered and ordered structures in the temperature region from 80 to 160 K.     

Electrochemical performances of poly(3,4-ethylenedioxythiophene)-NiFe2O4 nanocomposite as electrode for supercapacitor

Poly 3,4-ethylenedioxythiophene (PEDOT)-based NiFe₂O₄ conducting nanocomposites were synthesized and their electrochemical properties were studied in order to find out their suitability as electrode materials for supercapacitor. Nanocrystalline nickel ferrites (5-20 nm) have been synthesized by sol-gel method. Reverse microemulsion polymerization in n-hexane medium for PEDOT nanotube and aqueous miceller dispersion polymerization for bulk PEDOT formation using different surfactants have been adopted. Structural morphology and characterization were studied using XRD, SEM, TEM and IR spectroscopy. Electrochemical performances of these electrode materials were carried out using cyclic voltammetry at different scan rates (2-20 mV/s) and galvanostatic charge-discharge at different constant current densities (0.5-10 mA/cm²) in acetonitrile solvent containing 1 M LiClO₄ electrolyte. Nanocomposite electrode material shows high specific capacitance (251 F/g) in comparison to its constituents viz NiFe₂O₄ (127 F/g) and PEDOT (156 F/g) where morphology of the pore structure plays a significant role over the total surface area. Contribution of pseudocapacitance (C_FS) arising from the redox reactions over the electrical double layer capacitance (C_DL) in the composite materials have also been investigated through the measurement of AC impedance in the frequency range 10 kHz-10 mHz with a potential amplitude of 5 mV. The small attenuation (∼16%) in capacitance of PEDOT-NiFe₂O₄ composite over 500 continuous charging/discharging cycles suggests its excellent electrochemical stability.     

Multiwall carbon nanotube supported poly(3,4-ethylenedioxythiophene)/manganese oxide nano-composite electrode for super-capacitors

MWCNT-PSS/PEDOT/MnO₂ nano-composite electrodes were fabricated by generating pseudo-capacitive poly(3,4-ethylenedioxythiophene) (PEDOT)/MnO₂ nano-structures on poly(styrene sulfonate) (PSS) dispersed multiwalled carbon nanotubes (MWCNTs). PSS dispersed MWCNTs (MWCNT-PSS) facilitated the growth of PEDOT and MnO₂ into nano-rods with large active surface area and good electrical conductivity. The ternary MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode was studied for the application in super-capacitors, and exhibited excellent capacitive behavior between −0.2 V and 0.8 V (vs. saturated Ag/AgCl electrode) with high reversibility. Specific capacitance of the nano-composite electrode was found as high as 375 F g⁻¹. In contrast, specific capacitance of MWCNT-PSS/MnO₂ and MWCNT-PSS nano-composite electrodes is 175 F g⁻¹ and 15 F g⁻¹, respectively. Based on cyclic voltammetric studies and cycle-life tests, the MWCNT-PSS/PEDOT/MnO₂ nano-composite electrode gave a highly stable and reversible performance up to 2000 cycles. Our studies demonstrate that the synergistic combination of MWCNT-PSS, PEDOT and MnO₂ has advantages over the sum of the individual components.     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Electropolymerization of a poly(3,4-ethylenedioxythiophene) and functionalized, multi-walled, carbon nanotubes counter electrode for dye-sensitized solar cells and characterization of its performance

Composite films of poly(3,4-ethylenedioxythiophene) and functionalized, multi-walled, carbon nanotubes (PEDOT–MWCNT) were fabricated by a simple oxidative electropolymerization method. These films were formed on fluorine-doped, tin oxide, glass substrates as counter electrodes (CEs) of platinum-free, dye-sensitized solar cells (DSSCs). The surface morphology, formation mechanism and electrochemical nature of PEDOT–MWCNT films were investigated using scanning electron microscopy (SEM), atomic force microscopy (AFM), cyclic voltammetry (CV) and alternating current (AC) impedance spectroscopy. The SEM and AFM images showed that PEDOT–MWCNT films were more porous than PEDOT films. CV and AC impedance spectroscopy revealed that the PEDOT–MWCNT electrode had higher electrocatalytic activity for the I₃⁻/I⁻ redox reaction and a smaller charge transfer resistance than the PEDOT electrodes. The energy conversion efficiency of the DSSC with a PEDOT–MWCNT CE was 13.0% higher than with a PEDOT CE using the same conditions with a ruthenium sensitizer.     

Electrochemical behavior of LiCoO2 in a saturated aqueous Li2SO4 solution

The electrochemical behavior of a commercial LiCoO₂ with spherical shape in a saturated Li₂SO₄ aqueous solution was investigated with cyclic voltammetry and electrochemical impedance spectroscopy. Three redox couples at E_SCE = 0.87/0.71, 0.95/0.90 and 1.06/1.01 V corresponding to those found at ELi/Li⁺=4.08/3.83, 4.13/4.03 and 4.21/4.14 V in organic electrolyte solutions were observed. The diffusion coefficient of lithium ions is 1.649 × 10⁻¹⁰ cm² s⁻¹, close to the value in organic electrolyte solutions. The results indicate that the intercalation and deintercalation behavior of lithium ions in the Li₂SO₄ solution is similar to that in the organic electrolyte solutions. However, due to the higher ionic conductivity of the aqueous solution, current response and reversibility of redox behavior in the aqueous solution are better than in the organic electrolyte solutions, suggesting that the aqueous solution is favorable for high rate capability. The charge transfer resistance, the exchange current and the capacitance of the double layer vary with the charge voltage during the deintercalation process. At the peak of the oxidation (0.87 V), the charge transfer resistance is the lowest. These fundamental results provide a good base for exploring new safe power sources for large scale energy storage.     

Synthesis and electrochemical properties of CeO2 nanoparticle modified TiO2 nanotube arrays

In this paper, a cerium dioxide (CeO₂) modified titanium dioxide (TiO₂) nanotube array film was fabricated by electrodeposition of CeO₂ nanoparticles onto an anodized TiO₂ nanotube array. The structural investigation by X-ray diffraction, scanning electron microscopy and transmission electron microscopy indicated that the CeO₂ nanoparticles grew uniformly on the walls of the TiO₂ nanotubes. The composite was composed of cubic-phase CeO₂ crystallites and anatase-phase TiO₂ after annealing at 450 °C. The cyclic voltammetry and chronoamperometric charge/discharge measurement results indicated that the CeO₂ modification obviously increased the charge storage capacity of the TiO₂ nanotubes. The charge transfer process at the surface, that is, the pseudocapacitance, was the dominate mechanism of the charge storage in CeO₂-modified TiO₂ nanotubes. The greater number of surface active sites resulting from uniform application of the CeO₂ nanoparticles to the well-aligned TiO₂ nanotubes contributed to the enhancement of the charge storage density.     

A novel photoelectrocatalytic system for organic contaminant degradation on a TiO2 nanotube (TNT)/Ti electrode

A novel degradation system, combined with photon-efficient thin-film photocatalysis, conventional bulk-phase photocatalysis and photocarrier-efficient electrocatalysis (TBPE), was developed on a vertically ordered one-dimensional (1D) TiO₂ nanotube (TNT)/Ti electrode for the purification of organics. The TBPE system possessed excellent optical, electrochemical, photoelectrochemical and photoelectrocatalytic properties as well as a high mass-transfer coefficient and interfacial activity. The combined degradation of methyl orange (MO) was optimized by varying the rotation angular velocity, applied bias and substrate concentration, and a photoelectrochemical synergetic effect of 62.2% was observed under the optimized conditions for TBPE compared to the individual electrocatalytic (EC) and photocatalytic (PC) systems. To explore the mechanisms, the combined thin-film degradation system of photon-efficient thin-film photocatalysis with photocarrier-efficient electrocatalysis (TPE), and the combined bulk-phase degradation system of conventional bulk-phase photocatalysis with photocarrier-efficient electrocatalysis (BPE), were comparatively estimated. A dramatic increase of 29.4-74.4% was observed in the MO removal efficiency via the thin-film TPE system compared to the bulk-phase BPE system. The results indicated that in the proposed TBPE system on the 1D TNT electrode, the predominant degradation occurred via the TPE system due to its excellent UV utilization efficiency and resultant interfacial photoactivity.     

An efficient and low-cost TiO2 compact layer for performance improvement of dye-sensitized solar cells

A TiO₂ organic sol was synthesised for the preparation of a compact TiO₂ layer on fluorine-doped tin oxide (FTO) glass by a dip-coating technique. The resultant thin film was used for the fabrication of dye-sensitized solar cells (DSSCs). The compact layer typically has a thickness of ca. 110 nm as indicated by its SEM, and consists of anatase as confirmed by the XRD pattern. Compared with the traditional DSSCs without this compact layer, the solar energy-to-electricity conversion efficiency, short-circuit current and open-circuit potential of the DSSCs with the compact layer were improved by 33.3%, 20.3%, and 10.2%, respectively. This can be attributed to the merits brought by the compact layer. It can effectively improve adherence of TiO₂ to FTO surface, provide a larger TiO₂/FTO contact area, and reduce the electron recombination by blocking the direct contact between the redox electrolyte and the conductive FTO surface.     

TiO2-B narrow nanobelt/TiO2 nanoparticle composite photoelectrode for dye-sensitized solar cells

In order to possess the merits of both building blocks, i.e. the rapid interfacial electron transport of TiO₂-B narrow nanobelts (NBs) and the high surface area of TiO₂ nanoparticles (NPs), the TiO₂-B NBs and TiO₂ NPs composites photoelectrodes were prepared with different weight ratios. The dye-sensitized solar cell prototypes were fabricated based on the composite photoelectrodes and the photoelectrical properties have been systematically studied. Although the amount of adsorption dye of composite solar cells decreased, the composite cells could obtain higher power conversion efficiency compared to pure TiO₂ NP solar cell by rational tuning the weight ratio of TiO₂-B NBs and TiO₂ NPs, which was due to the faster electron transfer rate. The dye adsorption amount and interfacial electron transport, which together determined the overall photoelectrical conversion efficiency, were investigated by the UV–vis spectra, the electrochemical impedance spectra (EIS), intensity-modulated photocurrent spectroscopy (IMPS) and intensity-modulated photovoltage spectroscopy (IMVS).