The influence of preparation conditions on electrochemical properties of LiNi0.5Mn1.5O4 thin film electrodes by PLD

LiNi_0.5Mn_1.5O₄ thin films were prepared by pulsed laser deposition (PLD) on stainless steel substrates. The growth of the films has been studied as a function of substrate temperature and oxygen partial pressure in deposition, using X-ray diffraction (XRD) and field-emission scanning electron microscopy (FESEM). Electrochemical properties of LiNi_0.5Mn_1.5O₄ thin film cathodes were investigated using cyclic voltammetry and galvanostatic charge/discharge against a lithium anode. The initial capacity and capacity retention of the films are highly dependent on the crystallinity and purity of the films. LiNi_0.5Mn_1.5O₄ thin films grown at 600 °C in an oxygen partial pressure of 200 mTorr are well crystallized with high purity, exhibiting excellent capacity retention between 3 and 5 V with a LiPF₆-based electrolyte.     

Electrochemical investigation of LiNi0.5Mn1.5O4 thin film intercalation electrodes

This work provides kinetic and transport parameters of Li-ion during its extraction/insertion into thin film LiNi_0.5Mn_1.5O₄ free of binder and conductive additive. Thin films of LiNi_0.5Mn_1.5O₄ (0.2 μm thick) were prepared on electronically conductive gold substrate utilizing the electrostatic spray deposition technique. High purity LiNi_0.5Mn_1.5O₄ thin film electrodes were observed with cyclic voltammetry, to exhibit very sharp peaks, high reversibility, and absence of the 4 V signal related to the Mn³⁺/Mn⁴⁺ redox couple. The electrode subjected to 100 CV cycles of charge/discharge delivered a capacity of 155 mAh g⁻¹ on the first cycle and sustained a good cycling behavior while retaining 91% of the initial capacity after 50 cycles. Kinetics and mass-transport of Li-ion extraction at LiNi_0.5Mn_1.5O₄ thin film electrode were investigated by means of electrochemical impedance spectroscopy. The apparent chemical diffusion coefficient (D_app) value determined from EIS measurements changed depending on the electrode potential in the range of 10⁻¹⁰-10⁻¹² cm² s⁻¹. The D_app profile shows two minimums at the potential values close to the peak potentials of the corresponding cyclic voltammogram.     

Particle size effect of Li[Ni0.5Mn0.5]O2 prepared by co-precipitation

Spherical (Ni_0.5Mn_0.5)(OH)₂ with different secondary particle size (3 μm, 10 μm in diameter) was synthesized by co-precipitation method. Mixture of the prepared hydroxide and lithium hydroxide was calcined at 950 °C for 20 h in air. X-ray diffraction patterns revealed that the prepared material had a typical layered structure with space group. Spherical morphologies with mono-dispersed powders were observed by scanning electron microscopy. It was found that the layered Li[Ni_0.5Mn_0.5]O₂ delivered an initial discharge capacity of 148 mAh g⁻¹ (3.0-4.3 V) though the particle sizes were different. Li[Ni_0.5Mn_0.5]O₂ having smaller particle size (3 μm) showed improved area specific impedance due to the reduced Li⁺ diffusion path, compared with that of Li[Ni_0.5Mn_0.5]O₂ possessing larger particle size (10 μm). Although the Li[Ni_0.5Mn_0.5]O₂ (3 μm) was electrochemically delithiated to Li_0.39[Ni_0.5Mn_0.5]O₂, the resulting exothermic onset temperature was around 295 °C, of which the value is significantly higher than that of highly delithiated Li_1−δCoO₂ (∼180 °C).     

Electrochemical characteristics of LiNi0.5Mn1.5O4 prepared by spray drying and post-annealing

LiNi_0.5Mn_1.5O₄ was prepared by a spray drying and post-annealing process. The re-annealing treatment in O₂ could not only decrease the Mn³⁺ content, but also increased the reversible capacity and significantly improve the rate capability compared to the untreated material. Moreover, the cyclic performance of the LiNi_0.5Mn_1.5O₄ depends on both the cycling rate and operating temperature, which was ascribed to the difference between the phase transition rates between cubic I ↔ cubic II and cubic II ↔ cubic III.     

Texture effect on the electrochemical properties of LiCoO2 thin films prepared by PLD

LiCoO₂ thin films were prepared by pulsed laser deposition (PLD) on Pt/Ti/SiO₂/Si (Pt) and Au/MgO/Si (Au) substrates, respectively. Crystal structures and surface morphologies of thin films were investigated by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The LiCoO₂ thin films deposited on the Pt substrates exhibited a preferred (0 0 3) texture with smooth surfaces while the LiCoO₂ thin films deposited on the Au substrates exhibited a preferred (1 0 4) texture with rough surfaces. The electrochemical properties of the LiCoO₂ films with different textures were compared with charge-discharge, dQ/dV, and Li diffusion measurements (PITT). Compared with the (1 0 4)-textured LiCoO₂ thin films, the (0 0 3)-textured thin films exhibited relatively lower electrochemical activity. However, the advantage of the (1 0 4)-textured film only remained for a small number of cycles due to the relatively faster capacity fade. Li diffusion measurements showed that the Li diffusivity in the (0 0 3)-textured film is one order of magnitude lower than that in the (1 0 4)-textured film. As discussed in this paper, we believe that Li diffusion through grain boundaries is comparable to or even faster than Li diffusion through the grains.     

Molten salt synthesis of spherical LiNi0.5Mn1.5O4 cathode materials

This paper describes a novel simple redox process for synthesizing monodispersed MnO₂ powders and preparation of spherical LiNi_0.5Mn_1.5O₄ cathode materials by molten salt synthesis (MSS) method. Monodispersed MnO₂ powders have been synthesized by using potassium permanganate and manganese sulfate as the starting materials. By using this redox method, it was found that monodispersed MnO₂ powders with average particle size ∼5 μm can be easily obtained. Resultant MnO₂ and LiOH, Ni(OH)₂ was then used to synthesis LiNi_0.5Mn_1.5O₄ cathode materials with retention of spherical particle shape by MSS method. The discharge capacity was 129 mAh g⁻¹ in the first cycle and 127 mAh g⁻¹ after 50 cycles under an optimal synthesis condition for 12 h at 800 °C.     

Low-temperature solution combustion synthesis of high performance LiNi0.5Mn1.5O4

High-voltage LiNi_0.5Mn_1.5O₄ spinels were synthesized by a low temperature solution combustion method at 400 °C, 600 °C and 800 °C for 3 h. The phase composition, structural disordering, micro-morphologies and electrochemical properties of the products were investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM) and constant current charge–discharge test. XRD analysis indicated that single phase LiNi_0.5Mn_1.5O₄ powders with disordered Fd-3m structures were obtained by the method at 400 °C, 600 °C and 800 °C. The crystallinity increased with increasing preparation temperatures. XRD and FTIR data indicated that the degree of structural disordering in the product prepared at 800 °C was the largest and in the product prepared at 600 °C was the least. SEM investigation demonstrated that the particle size and the crystal perfection of the products were increased with increasing temperatures. The particles of the product prepared at 600 °C with ~200 nm in size are well developed and homogeneously distributed. Charge/discharge curves and cycling performance tests at different current density indicated that the product prepared at 600 °C had the largest specific capacity and the best cycling performance, due to its high purity, high crystallinity, small particle size as well as moderate amount of Mn³⁺ ions.     

Nano-crystalline LiNi0.5Mn1.5O4 synthesized by emulsion drying method

LiNi_0.5Mn_1.5O₄ spinel has been prepared by an emulsion drying method which can intermix cations very homogeneously at the atomic scale. When the emulsion-dried precursor was fired at 750 °C for 24 h, the observed particle of the LiNi_0.5Mn_1.5O₄ was nano-crystallite, being about 50 nm in diameter. The Rietveld refinement result clearly exhibited that the cubic spinel phase was successfully formed without any secondary phases, indicating that Li and transition metal cations occupied the 8a and 16d sites of the Fd3m structure, respectively. Li deintercalation from the spinel framework brings about a shift in the XRD peak toward higher angles and a peak splitting in the composition range δ=0-0.2 in Li_δNi_0.5Mn_1.5O₄, implying that the host structure is progressively oxidized from Ni²⁺ to Ni⁴⁺ and accompanied by a two phase reaction. The sample calcined at 750 °C for 24 h showed the best cyclability upon cycling due probably to better crystallinity and a smaller particle size. We suggest that this material can be used as a 4.5 V cathode material for Li-ion battery.     

Properties of nano-crystalline LiMn2O4 thin films deposited by pulsed laser deposition

Properties of LiMn₂O₄ thin films deposited on polished stainless steel substrates at 400 °C and 200 mTorr of oxygen by pulsed laser deposition have been characterized by electrochemical measurements and physical analyses. The film was mainly composed of nano-crystals less than 100 nm. A maximum specific capacity of 141.9 mAh/g cycled between 3.0 and 4.5 V with a current density of 20 μAh/cm² has been achieved. The film exhibited an excellent cycling stability up to 500 cycles. The low charge-transfer resistance at high potentials as revealed by AC impedance resulted in high charge/discharge potential and more capacity. The effect of overdischarge was limited and Jahn-Teller effect was overcome to a significant extent in this nano-crystalline film. Ex situ XRD, Raman and XPS provided supporting evidence in the changes in structure, reactivity and cycling stability of nano-crystalline LiMn₂O₄ film cathodes under different charge/discharge states and cycling tests. SEM images also revealed the stability of the surface topography after a long-term cycling test.     

Synthesis and electrochemical performance of LiNi0.5Mn1.5O4 spinel compound

Spinel compound LiNi_0.5Mn_1.5O₄ was synthesized by a chemical wet method. Mn(NO₃)₂, Ni(NO₃)₂·6H₂O, NH₄HCO₃ and LiOH·H₂O were used as the starting materials. At first, Mn(NO₃)₂ and Ni(NO₃)₂·6H₂O reacted with NH₄HCO₃ to produce a precursor, then the precursor reacted with LiOH·H₂O to synthesize product LiNi_0.5Mn_1.5O₄. The product showed a single spinel phase under appropriate calcination conditions, and exhibited a high voltage plateau at about 4.6-4.8 V in the charge/discharge process. The LiNi_0.5Mn_1.5O₄ had a discharge specific capacity of 118 mAh/g at about 4.6 V and 126 mAh/g in total in the first cycle at a discharge current density of 2 mA/cm². After 50 cycles, the total discharge capacity was above 118 mAh/g.     

Enhanced electrochemical performances of LiNi0.5Mn1.5O4 spinel via ethylene glycol-assisted synthesis

A simple and effective method, ethylene glycol-assisted co-precipitation method, has been employed to synthesize LiNi_0.5Mn_1.5O₄ spinel. As a chelating agent, ethylene glycol can realize the homogenous distributions of metal ions at the atomic scale and prevent the growth of LiNi_0.5Mn_1.5O₄ particles. XRD reveals that the prepared material is a pure-phase cubic spinel structure (Fd3m) without any impurities. SEM images show that it has an agglomerate structure with the primary particle size of less than 100 nm. Electrochemical tests demonstrate that the as-prepared LiNi_0.5Mn_1.5O₄ possesses high capacity and excellent rate capability. At 0.1 C rate, it shows a discharge capacity of 137 mAh g⁻¹ which is about 93.4% of the theoretical capacity (146.7 mAh g⁻¹). At the high rate of 5 C, it can still deliver a discharge capacity of 117 mAh g⁻¹ with excellent capacity retention rate of more than 95% after 50 cycles. These results show that the as-prepared LiNi_0.5Mn_1.5O₄ is a promising cathode material for high power Li-ion batteries.     

Effect of ZnO modification on the performance of LiNi0.5Co0.25Mn0.25O2 cathode material

ZnO was coated on LiNi_0.5Co_0.25Mn_0.25O₂ cathode (positive electrode) material for lithium ion battery via sol–gel method to improve the performance of LiNi_0.5Co_0.25Mn_0.25O₂. The X-ray diffraction (XRD) results indicated that the lattice structure of LiNi_0.5Co_0.25Mn_0.25O₂ was not changed distinctly after surface coating and part of Zn²⁺ might dope into the lattice of the material. Energy dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) proved that ZnO existed on the surface of LiNi_0.5Co_0.25Mn_0.25O₂. Charge and discharge tests showed that the cycle performance and rate capability were improved by ZnO coating, however, the initial capacity decreased dramatically with increasing the amount of ZnO. Differential scanning calorimetry (DSC) results showed that thermal stability of the materials was improved. The XPS spectra after charge–discharge cycles showed that ZnO coated on LiNi_0.5Co_0.25Mn_0.25O₂ promoted the decomposition of the electrolyte at the early stage of charge–discharge cycle to form more stable SEI layer, and it also can scavenge the free acidic HF species from the electrolyte. The electrochemical impedance spectroscopy (EIS) results showed ZnO coating could suppress the augment of charge transfer resistance upon cycling.     

Li-ion diffusion kinetics in LiMn2O4 thin films prepared by pulsed laser deposition

LiMn₂O₄ thin films were deposited on Au substrates by pulsed laser deposition (PLD). The Li-ion chemical diffusion coefficients of the films, , were measured by cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT), potentiostatic intermittent titration technique (PITT), and electrochemical impedance spectroscopy (EIS). It was found that the values by CV and PITT were in the order of 10⁻¹³ cm² s⁻¹, and those by EIS and GITT were in the range of 10⁻¹³ to 10⁻¹¹ and 10⁻¹⁴ to 10⁻¹¹ cm² s⁻¹, respectively. These data were compared with the previously reported values.     

Impact of cobalt substitution for manganese on the structural and electrochemical properties of LiNi0.5Mn0.5O2

A series of LiNi_0.5Mn_0.5−xCo_xO₂ (0 ≤ x ≤ 0.5) compounds was prepared by a solid state reaction, and their structure, surface state and electrochemical characteristics were also investigated by XRD, XPS, EIS and charge-discharge cycling. The non-equivalent substitution of cobalt for manganese induced an increase in the average valence of nickel, thereby shrinking in the lattice volume. Moreover, Co non-equivalent substitution could not only reduce the impurity content but also significantly decreased the charge transfer resistance, thereby improving the rate capabilities.     

Effects of precursor treatment with reductant or oxidant on the structure and electrochemical properties of LiNi0.5Mn1.5O4

LiNi_0.5Mn_1.5O₄, a lithium-ion battery cathode material, is prepared using co-precipitation via a two-step drying method with Ni-Mn mixed hydroxide as the precursor. This study examines the effects of precursor pretreatment with hydrazine (a reductant) or with H₂O₂ (an oxidant) in solutions of NiSO₄ and MnSO₄. The results indicate substantial differences in the structure and electrochemical properties of LiNi_0.5Mn_1.5O₄ depending on whether the precursor is pretreated with reductant or oxidant. For the hydrazine-treated precursor, the synthesized LiNi_0.5Mn_1.5O₄ has a very pure spinel phase and an ordered, octahedral crystal morphology (ca. 100-300 nm). In contrast, the material synthesized using the H₂O₂-treated precursor shows numerous impurity phases (Na_0.7MnO_2.05) with a layer-by-layer crystal structure. The control sample (prepared without precursor pretreatment) maintains an octahedral structure but still retains a few impurity phases of Na_0.7MnO_2.05. The electrochemical results show that LiNi_0.5Mn_1.5O₄ synthesized using a hydrazine-treated precursor has a higher specific capacity (especially under high discharge current) and a higher cyclic life than the control sample, whereas the sample using H₂O₂-treated precursor shows almost no special capacity due to changes in crystal structure.     

Molten salt synthesis of LiNi0.5Mn1.5O4 spinel for 5 V class cathode material of Li-ion secondary battery

Well-ordered high crystalline LiNi_0.5Mn_1.5O₄ spinel has been readily synthesized by a molten salt method using a mixture of LiCl and LiOH salts. Synthetic variables on the synthesis of LiNi_0.5Mn_1.5O₄, such as synthetic atmosphere, LiCl salt amount, synthetic temperature, and synthetic time, were intensively investigated. X-ray diffraction (XRD) patterns and scanning electron microscopic (SEM) images showed that LiNi_0.5Mn_1.5O₄ synthesized at 900 and 950 °C have cubic spinel structure () with clear octahedral dimension. LiNi_0.5Mn_1.5O₄ spinel phase began to decompose at around 1000 °C accompanied with structural and morphological degradation. LiNi_0.5Mn_1.5O₄ powders synthesized at 900 °C for 3 h delivered an initial discharge capacity of 139 mAh/g with excellent capacity retention rate more than 99% after 50 cycles.     

Effects of the nanostructured SiO2 coating on the performance of LiNi0.5Mn1.5O4 cathode materials for high-voltage Li-ion batteries

LiNi_0.5Mn_1.5O₄ spinels coated with various amounts of fumed silica have been synthesized and investigated as cathode materials for high-voltage lithium-ion batteries at the elevated temperature (55 °C). The morphology and structure of the coated LiNi_0.5Mn_1.5O₄ samples were characterized by XRD, TEM and EDX. It was found that the surfaces of the coated LiNi_0.5Mn_1.5O₄ samples are covered with a porous, amorphous, nanostructured SiO₂ layer. The results of electrochemical experiments showed that the SiO₂-coated LiNi_0.5Mn_1.5O₄ samples display obviously improved capacity retention rate, and the improvement effect enhances with the increase of SiO₂ content. The XPS results revealed that the surfaces of the SiO₂-coated LiNi_0.5Mn_1.5O₄ cathode materials have relatively low content of LiF, and this is mainly responsible for their improved electrochemical cycling stability.     

Novel synthesis of layered LiNi1/2Mn1/2O2 as cathode material for lithium rechargeable cells

A new solution combustion synthesis of layered LiNi_0.5Mn_0.5O₂ involving the reactions of LiNO₃, Mn(NO₃)₂, NiNO₃, and glycine as starting materials is reported. TG/DTA studies were performed on the gel-precursor and suggest the formation of the layered LiNi_0.5Mn_0.5O₂ at low temperatures. The synthesized material was annealed at various temperatures, viz., 250, 400, 600, and 850 °C, characterized by means of X-ray diffraction (XRD) and reveals the formation of single phase crystalline LiNi_0.5Mn_0.5O₂ at 850 °C. The morphology of the synthesized material has been investigated by means of scanning electron microscopy (SEM) and suggests the formation of sub-micron particles. X-ray photoelectron spectroscopy (XPS) and cyclic voltammetry (CV) studies on the synthesized LiNi_0.5Mn_0.5O₂ powders indicate that the oxidation states of nickel and manganese are +2 and +4, respectively. Electrochemical galvanostatic charge-discharge cycling behavior of Li//LiNi_0.5Mn_0.5O₂ cell using 1 M LiPF₆ in EC/DMC as electrolyte exhibited stable capacities of ∼125 mAh/g in the voltage ranges 2.8-4.3 V and 3.0-4.6 V and is comparable to literature reports using high temperature synthesis route. The capacity remains stable even after 20 cycles. The layered LiNi_0.5Mn_0.5O₂ powders synthesized by this novel route have several advantages as compared to its conventional synthesis techniques.     

Formation of LiNi0.5Co0.5VO4 nano-crystals by solvothermal reaction

LiNi_0.5Co_0.5VO₄ nano-crystals were solvothermally prepared using a mixture of LiOH·H₂O, Ni(NO₃)₂·6H₂O, Co(NO₃)₂·6H₂O and NH₄VO₃ in isopropanol at 150–200 °C followed by 300–600 °C calcination to form powders. TGA curves of the solvothermal products show weight losses due to evaporation and decomposition processes. The purified products seem to form at 500 °C and above. The products analyzed by XRD, selected area electron diffraction (SAED), energy dispersive X-ray (EDX) and atomic absorption spectrophotometer (AAS) correspond to LiNi_0.5Co_0.5VO₄. V–O stretching vibrations of VO₄ tetrahedrons analyzed using FTIR and Raman spectrometer are in the range of 620–900 cm⁻¹. A solvothermal reaction at 150 °C for 10 h followed by calcination at 600 °C for 6 h yields crystals with lattice parameter of 0.8252 ± 0.0008 nm. Transmission electron microscope (TEM) images clearly show that the solvothermal temperatures play a more important role in the size formation than the reaction times.