Characterization of CuInSe2/CdS thin-film solar cells prepared using CBD

CuInSe₂/CdS thin-film heterojunction solar cells were fabricated entirely by chemical bath deposition technique. The illuminated J−V characteristics of the devices prepared with different thicknesses of CdS and CuInSe₂ were studied. The typical solar cell parameters obtained for the best cell are: V_oc = 365 mV, J_sc = 12 mA/cm², FF = 61%, and η = 3.1% under an illumination of 85 mW/cm² on a cell of active area 0.1 cm². The J−V and C−V characteristics under dark condition and the spectral response were also studied for the best cell. The diode quality factor obtained is 1.7.     

Influence of aminothiazole additives in I/I3 redox electrolyte solution on Ru(II)-dye-sensitized nanocrystalline TiO2 solar cell performance

The influence of aminothiazole additives in acetonitrile solution of an I⁻/I₃⁻ redox electrolyte on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′- bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized TiO₂ solar cell was studied. The current–voltage characteristics were investigated under AM 1.5 (100 mW/cm²) for nine different aminothiazole compounds. The aminothiazole additives tested had varying influences on the solar cell performance. Most of the additives enhanced the open-circuit photovoltage (V_oc), but reduced the short circuit photocurrent density (J_sc) of the solar cell. Both the physical and chemical properties of the aminothiazoles were computationally calculated in order to determine the reasons that the additive influenced solar cell performance. The larger the calculated partial charge of the nitrogen atom in the thiazole, the higher the V_oc value. The V_oc value increased as the dipole moment of aminothiazoles in acetonitrile increased. Moreover, the V_oc of the solar cell also increased as the size of the aminothiazole molecules decreased. These results suggest that the electron donicity of the aminothiazole additives influenced the interaction with the TiO₂ photoelectrode, which altered the dye-sensitized solar cell performance.     

Influence of alkylaminopyridine additives in electrolytes on dye-sensitized solar cell performance

The influence of alkylaminopyridine additives on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile was studied. The current–voltage characteristics were measured for more than 20 different alkylaminopyridines under AM 1.5 (100 mW/cm²). The alkylaminopyridine additives tested had varying effects on the performance of the cell. All the additives decreased the short circuit photocurrent density (J_sc), but increased the open-circuit photovoltage (V_oc) of the solar cell. Molecular orbital calculations imply that the dipole moment of the alkylaminopyridine molecules influences the J_sc of the cell and that the size, solvent accessible surface area, and ionization energy all affect the V_oc of the cell. The highest V_oc of 0.88 V was observed in an electrolyte containing 4-pyrrolidinopyridine, which is comparable to the maximum V_oc of 0.9 V for a cell consisting of TiO₂ electrode and I⁻/I₃⁻ redox system.     

Highly efficient photon-to-electron conversion with mercurochrome-sensitized nanoporous oxide semiconductor solar cells

Dye-sensitized solar cells based on nanoporous oxide semiconductor thin films such as TiO₂, Nb₂O₅, ZnO, SnO₂, and In₂O₃ with mercurochrome as the sensitizer were investigated. Photovoltaic performance of the solar cell depended remarkably on the semiconductor materials. Mercurochrome can convert visible light in the range of 400–600 nm to electrons. A high incident photon-to-current efficiency (IPCE), 69%, was obtained at 510 nm for a mercurochrome-sensitized ZnO solar cell with an I⁻/I₃⁻ redox electrolyte. The solar energy conversion efficiency under AM1.5 (99 mW cm⁻²) reached 2.5% with a short-circuit photocurrent density (J_sc) of 7.44 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.52 V, and a fill factor (ff) of 0.64. The J_sc for the cell increased with increasing thickness of semiconductor thin films due to increasing amount of dye, while the V_oc decreased due to increasing of loss of injected electrons due to recombination and the rate constant for reverse reaction. Dependence of photovoltaic performance of mercurochrome-sensitized solar cells on semiconductor particles, light intensity, and irradiation time were also investigated. High performance of mercurochrome-sensitized ZnO solar cells indicate that the combination of dye and semiconductor is very important for highly efficient dye-sensitized solar cells and mercurochrome is one of the best sensitizers for nanoporous ZnO photoelectrode. In addition, a possibility of organic dye-sensitized oxide semiconductor solar cells has been proposed as well as one using metal complexes.     

Boron-doped diamond-like amorphous carbon as photovoltaic films in solar cell

In this paper, the photovoltaic feature of metal-boron carbide-silicon (MCS) solar cell was reported. The boron-doped diamond-like carbon thin film on n-silicon substrate has been prepared using arc-discharge plasma chemical vapor deposition (PCVD) technique. The conductivity and the resistivity of the film were measured by Bio-Rad Hall5500PC system to be p-type semiconductor and 3–12 Ω cm/□, respectively. The boron content in the films was about 0.8–1.2%, obtained from Auger electron spectroscopy (AES), and some microcrystalline diamond grains (0.5–1.0 μm) embedded in the mainly amorphous network were revealed through scanning electron microscope (SEM) and Raman spectrum. The performance of Au/C(B)/n-Si heterojunction solar cells has been given under dark I–V rectifying curve and I–V working curve (with 100 mW cm⁻² illumination). A measurement of open-circuit voltage V_oc=580 mV and short-circuit current density J_sc=32.5 mA cm⁻² was obtained. Accordingly, the energy conversion efficiency of the device was tentatively determined to be about 7.9% in AM 1.5, 100 mW/cm² illuminated.     

Photosensitization of nanocrystalline TiO2 films by a polymer with two carboxylic groups, poly (3-thiophenemalonic acid)

Photovoltaic devices were assembled using a conducting polymer; poly (3-thiophenemalonic acid) sensitized TiO₂ electrodes and an electrolyte containing I₃⁻/I⁻ redox couple. This cell exhibited a short-circuit photocurrent (J_sc) of 6.65 mA cm⁻², an open circuit voltage (V_oc) of 355 mV and an efficiency of 1.5% under the illumination of 100 mW cm⁻² (AM 1.5). Addition of an ionic liquid, 1-methyl 3-n-hexylimidazolium iodide, into the electrolyte led to an improvement in the cell performances, achieving an overall efficiency of 1.8% under the same illumination. The average cell characteristics of the later devices are , with a fill factor of 0.65.     

New trends to grow the n-CdZn (S1−xSex)2/p-CuIn(S1−xSex)2 heterojunction thin films for solar cell applications

The n-CdZn(S_1−xSe_x) and p-CuIn(S_1−xSe_x)₂ thin films have been grown by the solution growth technique (SGT) on glass substrates. Also the heterojunction (p–n) based on n-CdZn (S_1−xSe_x)₂ and p-CuIn (S_1−xSe_x)₂ thin films fabricated by same technique. The n-CdZn(S_1−xSe_x)₂ thin film has been used as a window material which reduced the lattice mismatch problem at the junction with CuIn (S_1−xSe_x)₂ thin film as an absorber layer for stable solar cell preparation. Elemental analysis of the n-CdZn (S_1−xSe_x)₂ and p-CuIn(S_1−xSe_x)₂ thin films was confirmed by energy-dispersive analysis of X-ray (EDAX). The structural and optical properties were changed with respect to composition ‘x’ values. The best results of these parameters were obtained at x=0.5 composition. The uniform morphology of each film as well as the continuous smooth thickness deposition onto the glass substrates was confirmed by SEM study. The optical band gaps were determined from transmittance spectra in the range of 350–1000 nm. These values are 1.22 and 2.39 eV for CuIn(S_0.5Se_0.5)₂ and CdZn(S_0.5Se_0.5)₂ thin films, respectively. J–V characteristic was measured for the n-CdZn(S_1−xSe_x)₂/p-CuIn(S_1−xSe_x)₂ heterojunction thin films under light illumination. The device parameters V_oc=474.4 mV, J_sc=13.21 mA/cm², FF=47.8% and η=3.5% under an illumination of 85 mW/cm² on a cell active area of 1 cm² have been calculated for solar cell fabrication. The J–V characteristic of the device under dark condition was also studied and the ideality factor was calculated which is equal to 1.9 for n-CdZn(S_0.5Se_0.5)₂/p-CuIn(S_0.5Se_0.5)₂ heterojunction thin films.     

Simulation and model validation of a horizontal shallow basin solar concentrator

Salt removal from drainage water is becoming increasingly important for sustainable irrigated arid land agriculture, where inadequate drainage infrastructure exists. Solar evaporation and concentration systems are currently in development in California for this purpose. The thermal behavior and evaporation rates of a horizontal shallow basin solar concentrator were modeled for design purposes and investigated experimentally in order to validate the model. Three different evaporation rate models were evaluated and compared. Measured and predicted peak brine temperatures differed by as much as 5 °C when using prescribed literature coefficients without calibration. Model prediction was improved by calibration so that peak brine temperature deviated less than 3 °C when tested against independent data sets.Minimum root mean square error was used to calibrate the mass transfer coefficient and absorptance of the collector surface for solar radiation, which are the main factors affecting the heat transfer associated with the solar concentrator. Calibrated collector surface absorptance for solar radiation declined while mass transfer coefficients were increased from reported literature values. Under calibration, the absorptance of the collector surface was adjusted from 0.8 to 0.61, and mass transfer coefficients estimated by Newell et al. [Newell, T.A., Smith, M.K., Cowie, R.G., Upper, J.M., Cler, C.L., 1994. Characteristics of a solar pond brine reconcentration system. Journal of Solar Energy Engineering 116 (2), 69–73] from 1.36 × 10⁻⁶(1.9 + 1.065V) to 1.70 × 10⁻⁶(1.84 + 1.0V) kg m⁻² s⁻¹ mm Hg⁻¹, by Manganaro and Schwartz [Manganaro, J.L., Schwartz, J.C., 1985. Simulation of an evaporative solar salt pond. Industrial & Engineering Chemistry Process Design and Development 24, 1245–1251] from 0.0208(1 + 0.224V) to 0.0233(1 + 0.214V) kg m⁻² h⁻¹ mm Hg⁻¹, and by Alagao et al. [Alagao, F.B., Akbarzadeh, A., Johnson, P.W., 1994. The design, construction, and initial operation of a closed-cycle, salt-gradient solar pond. Solar Energy 53 (4), 343–351] from 2.8 + 3.0V to 3.0 + 3.33V W m⁻² °C⁻¹. The calibrated models were tested using an independent data set. Maximum deviation between measured and predicted brine temperatures differed by less than 3 °C. The measured and predicted peak evaporation rates were between 1.2 and 1.4 kg m⁻² h⁻¹.The calibrated Newell model was used to predict the monthly productivity and daily maximum evaporation rates at Five Points, California for the year 2004. The productivity from April to September and from March to October was 80.7% and 94.3% of the total annual productivity, respectively.     

Influence of pyrazole derivatives in I/I3 redox electrolyte solution on Ru(II)-dye-sensitized TiO2 solar cell performance

The influence of pyrazole additives in an I⁻/I₃⁻ redox electrolyte solution on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized TiO₂ solar cell was studied. The current–voltage characteristics of the cell were measured using 18 different pyrazole derivatives. All of the pyrazole additives enhanced the open-circuit photovoltage (V_oc) and the solar energy conversion efficiency (η), but reduced the short-circuit photocurrent density (J_sc). Most of the pyrazoles improved fill factor (ff). The physical and chemical properties of the pyrazoles were computationally calculated in order to elucidate the reasons for the additive effects on cell performance. The greater the partial charge of the nitrogen atom at position 2 in the pyrazole group, the larger the V_oc, but the smaller the J_sc values. As the dipole moment of the pyrazole derivatives increased, the V_oc value increased, but the J_sc value decreased. The V_oc of the cell also increased as the ionization energy of the pyrazoles decreased. These results suggest that the electron donicity of the pyrazole additives affected the interaction with the nanocrystalline TiO₂ photoelectrode, the I⁻/I₃⁻ electrolyte, and the acetonitrile solvent, which changed the Ru(II)-dye-sensitized solar cell performance.     

Influence of alkylpyridine additives in electrolyte solution on the performance of dye-sensitized solar cell

The influence of alkylpyridines additive to an I⁻/I₃⁻ redox electrolyte in acetonitrile on the performance of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) dye-sensitized TiO₂ solar cell was studied. I–V measurements were performed using more than 30 different alkylpyridines. The alkylpyridine additives showed a significant influence on the performance of the cell. All the additives decreased the short-circuit photocurrent (J_sc), but most of the alkylpyridines increased the open-circuit photovoltage (V_oc) and fill factor (ff) of the solar cell. The results of the molecular orbital calculations suggest that the dipole moment of the alkylpyridine molecules correlate with the J_sc of the cell. These results also suggest that both the size and ionization energy of pyridines correlate with the V_oc of the cell. Under AM 1.5 (100 mW/cm²), the highest solar energy conversion efficiency (η) of 7.6% was achieved by using 2-propylpyridine as an additive, which was more effective than the previously reported additive, 4-t-butylpyridine.     

Bulk p-CuInSe2 photo-electrochemical solar cells

Dense CuInSe₂ of high quality, prepared by the fusion technique in evacuated quartz ampoule from stoichiometric melt, crystallizes in the chalcopyrite structure. Compositional analysis carried out by secondary ion mass spectrometry (SIMS) and energy dispersive spectroscopy (EDS) indicates a uniform distribution of elements through the depth and a composition close to the stoichiometry. The diffuse reflectance spectrum gives a band gap at 0.94 eV. The electrical conductivity follows an Arrhenius-type law with activation energy of 23 meV in conformity with polarons hopping. Above 320 °C, CuInSe₂ undergoes an irreversible oxidation. The thermal variation of the thermopower indicates p-type behavior attributed to copper deficiency and a hole mobility μ_300 K of 0.133 cm² V⁻¹ s⁻¹, thermally activated. In KCl media, the compound exhibits an excellent chemical stability with a corrosion rate of 8 μmol cm⁻² month⁻¹. The photo-electrochemical properties, investigated for the first time on the ingots, confirm the p-type conductivity. From the capacitance measurements, the flat band potential (V_fb=−0.62V_SCE) and the holes density (N_A=4×10¹⁷ cm⁻³) were determined. The valence band, located at 4.43 eV below vacuum, is made up of mainly Se orbital with little admixture of Cu character. The change of the electrolyte causes a variation in the potential V_fb (dV_fb/dpH=−0.058 V pH⁻¹) indicating strong OH⁻ adsorption. The fill factor in S²⁻ media was found to be 0.54; such result was corroborated by semi-logarithmic plots.     

Semiconductor-sensitized solar cells based on nanocrystalline In2S3/In2O3 thin film electrodes

A possibility of semiconductor-sensitized thin film solar cells have been proposed. Nanocrystalline In₂S₃-modified In₂O₃ electrodes were prepared with sulfidation of In₂O₃ thin film electrodes under H₂S atmosphere. The band gap (E_g) of In₂S₃ estimated from the onset of the absorption spectrum was approximately 2.0 eV. The photovoltaic properties of a photoelectrochemical solar cell based on In₂S₃/In₂O₃ thin film electrodes and I⁻/I₃⁻ redox electrolytes were investigated. This photoelectrochemical cell could convert visible light of 400–700 nm to electron. A highly efficient incident photon-to-electron conversion efficiency (IPCE) of 33% was obtained at 410 nm. The solar energy conversion efficiency, η, under AM 1.5 (100 mW cm⁻²) was 0.31% with a short-circuit photocurrent density (J_sc) of 3.10 mA cm⁻², a open-circuit photovoltage (V_oc) of 0.26 V, and a fill factor ( ff ) of 0.38.     

Examination of blocking current-voltage behaviour through defect chalcopyrite layer in ZnO/CdS/Cu(In,Ga)Se2/Mo solar cell

Blocking current-voltage behaviour of ZnO/CdS/Cu(In,Ga)Se₂/Mo solar cells, which is either temperature- or light-conditioned, is examined using a comprehensive numerical device simulator. Effects of defect states in the defect-chalcopyrite layer and at the CdS/defect-chalcopyrite interface are investigated. Acceptor-like defect states either in a defect-chalcopyrite layer or at the CdS/defect-chalcopyrite interface cause different trapping under red light or white light. This results in different potential profiles throughout the structure, which determine the changeable I−V behaviour under forward bias. Simulation results show that these acceptor-like defect states can also control the temperature-conditioned blocking I−V behaviour.     

Characterization of PV array output using a small number of measured parameters

The purpose of the present study was to develop a sufficiently good fit for the measured I–V curve of a PV module and array using only three easily measurable parameters: —the open-circuit voltage (V_oc); —the short-circuit current (I_sc); —the maximum power (P_m). With an additional three parameters ( ; ; ) it is possible to describe any I–V curve, taking into account cell temperature T and solar radiation Q. This method has been tested on various solar array panels as well as on a single 10 cm dia. solar cell. The difference between the real curve and the proposed fit was found to be less than 3 percent for a fixed temperature and radiation and about 6 percent for various combinations of temperature and radiation.     

Parameterization of a simple model to estimate monthly global solar radiation based on meteorological variables, and evaluation of existing solar radiation models for Tabouk, Saudi Arabia

Using 9 years of solar radiation data, we established a simple model to calculate the monthly mean global solar radiation on a horizontal surface in Tabouk (28.38° N, 36.6° E, Saudi Arabia). The model correlates the global solar radiation with five meteorological parameters. These parameters are the perceptible water vapor, air temperature, relative humidity, atmospheric pressure, and the mean monthly daily fraction of possible sunshine hours. The estimated global radiation from the model was compared with the measured values using the mean bias error (MBE), coefficient of correlation (R), root mean square error (RMSE), and mean percentage error (MPE). The t statistics were also applied as another indication of suitability. The model has a high coefficient of correlation (R = 0.99), MBE = −14 × 10⁻⁴ kW h/m², RMSE = 0.10 kW h/m², and MPE = −0.03%. It is believed that the model developed in this work is applicable for estimating, with great accuracy. The monthly mean daily global radiation at any site having similar conditions to those found in Tabouk.Furthermore, 29 regression models available in the literature were used to estimate the global solar radiation data for Tabouk. The selected models were different in terms of the variables they use and in the number of the variables they contained. The models were compared on the basis of the statistical errors considered above. Apart from Abdall’s model, which showed a reasonable estimate (MPE = −2.04%, MBE = −0.22 kW h/m², and RMSE = 0.59 kW h/m²), all the models under or overestimate the measured solar radiation values. Comparisons between these models and the produced model, from this study, were also considered. According to the statistical results, the model of Abdall showed the prediction closest to those estimated using the developed model.     

Density functional study of alkylpyridine–iodine interaction and its implications in the open-circuit photovoltage of dye-sensitized solar cell

A density functional theory (DFT) method was used to study the monomer and intermolecular charge-transfer complexes of 22 different alkylpyridines with diiodine. DFT calculations revealed that the σ* orbital of iodine interacts with the nitrogen lone pair in pyridines. The open-circuit photovoltage (V_oc) values of a bis(tetrabutylammonium)cis-bis(thiocyanato)bis(2,2′-bipyridine-4-carboxylic acid, 4′-carboxylate)ruthenium(II) (N719) dye-sensitized nanocrystalline TiO₂ solar cell with an I⁻/I₃⁻ redox electrolyte in acetonitrile using alkylpyridines additive were compared to computational calculations on the interaction between pyridines and I₂ by a DFT method. The optimized geometries, frequency analyses, Mulliken population analyses, and interaction energies suggest that the V_oc value of the solar cell is higher, the more alkylpyridine complexes with I₂.     

I–V curve simulation by multi-module simulator using I–V magnifier circuit

This paper presents an I–V curve simulation of PV array/modules using multi I–V magnifier circuits. The circuit magnifies an I–V output of a pn photo-sensor, which is regarded as a small solar cell, by analog technology. About 30 W I–V curve simulator circuits were made and their characteristics were evaluated. LED light irradiated into the photo-sensor works like irradiation of sun light on real PV modules. It has been confirmed that each voltage gain and current gain of the circuit is independently adjustable and the circuit magnifies an I–V output of the photo-sensor successfully. FF of the circuit can be modified by shunt register connected to the photo-sensor in parallel. The circuit showed enough response ability to apply the maximum power point tracker evaluation of PV inverters. Temperature dependence of module output can be simulated by temperature control of the photo-sensor. The result of output characteristics of series connection of the I–V magnifier circuits suggests that the simulator system composed of multi I–V magnifier circuit could simulate partial shading effect of PV array output.     

Microscale packed bed reactor for controlled hydrogen peroxide decomposition as a fuel cell oxidant aboard unmanned undersea vehicles

The multiphase catalytic decomposition of hydrogen peroxide into water and oxygen is notoriously susceptible to thermal runaway (heat of reaction: −98 kJ mol⁻¹). The high surface area to volume ratio (S/V) in a microscale packed bed (MPB) reactor (radius 0.5 mm) was investigated for reducing the risk of thermal runaway during hydrogen peroxide decomposition to oxygen intended as a fuel cell oxidant aboard an unmanned undersea vehicle (UUV). A microscale reactor channel with a S/V of 2 × 10³ m² m⁻³ simulated under convective cooling generated a significant heat rise (T rise  100 K), whereas a microreactor with a higher S/V (200 × 10³ m² m⁻³) achieved thermal control (T rise < 10 K) over the simulated reaction zone. Although thermal management was successfully accomplished using the higher S/V, experimental conversions of hydrogen peroxide to oxygen (5–18%) measured from the outlet were lower than simulated conversions (38–63%). Simulation assumptions, such as homogeneously dispersed flow and perfect catalyst interaction among other factors, contributed to the discrepancies between the simulated and experimental degrees of peroxide conversion to oxygen. Even though thermal control of the MPB was achieved, this work indicates that mass transfer limitations are a factor in the MPB reactor during a multiphase reaction, like decomposition of hydrogen peroxide to oxygen and water, and suggests means to overcome them even on the microscale level.     

Metastable volume changes of hydrogenated amorphous silicon and silicon–germanium alloys produced by exposure to light

Exposure of hydrogenated amorphous silicon, a-Si:H, to light produces large-scale structural changes and increases the density of dangling Si bond defects acting as efficient carrier recombination centers. The latter is the well-studied Staebler–Wronski effect (SWE). All light-induced changes are metastable and disappear after annealing to approximately 200°C. This review focuses on one of the large-scale changes, namely that of the macroscopic density of the material. In all device quality materials, the initial stress is compressive with values typically in the range of 10⁸–10⁹ Pa. Exposure to light produces additional compressive stress, which can exceed 2×10⁷ Pa. The observed change of stress is due to a change of the volume of the unsupported material and not of its elastic modulus. The relative volume change, ΔV/V, at 300 K becomes detectable at values in excess of about 10⁻⁶ after only a few photons per Si atom have been absorbed. ΔV/V saturates above 10⁻³, under high-intensity light after an average of more than 10⁶ photons per Si atom have been absorbed. ΔV/V initially grows with t^0.50±0.04 under CW illumination producing carrier generation rate G in the range of 10²¹ to a few 10²³ cm⁻³ s⁻¹. The approach to saturation is well fitted by a stretched exponential function with stretch exponent close to 0.5. ΔV/V is approximately proportional to G. The fastest and largest photo-expansion has been observed in the so-called “edge material” between the amorphous and microcrystalline state, produced by plasma enhanced CVD from increasingly diluted silane/hydrogen gas mixtures. The quantum efficiency of volume expansion has been observed to increase with the photon energy of the light in contrast to the SWE. No volume increase is observed in Ge rich a-Si_1−xGe_x:H alloys and in hydrogenated microcrystalline material. Photo-expansion and the SWE show marked difference in spatial extend in the network, different evolution in time and different wavelength dependence. Hence, the two effects appear to be independent even though both involve hydrogen.     

Interface characterisation of ZnSe/CuGaSe2 heterojunction

The ZnSe/CuGaSe₂ heterojunctions were fabricated by flash evaporation technique of CuGaSe₂ onto the (110) surface of ZnSe crystals. CuGaSe₂ layers had thickness 2–4 μm and showed a hole concentration up to (1.5–18.0)×10¹⁸ cm⁻³ and mobility μ4–24 cm² V⁻¹ s⁻¹ at 300 K. The charge carrier concentration in ZnSe crystals at 300 K was n=5.6×10¹⁶ cm⁻³ and their mobility μ=300 cm² V⁻¹ s⁻¹. The investigated ZnSe/CuGaSe₂ heterojunctions have at the interface an intermediate layer with a thickness of 450–750 Å and a linear graded band gap as well as an i-ZnSe compensated layer with a thickness of 1–2 μm and resistivity ρ10⁸–10⁹ Ω cm. The i-ZnSe layer is highly compensated due to the presence of Cu acceptor impurities. In this layer the Fermi level position E_c−F₀690 meV and a trap level position E_t−F₀17 meV were determined. The total trap concentration in the i-ZnSe layer is N_t5×10¹⁴ cm⁻³. The mean free path of excited charge carriers in the graded band gap region was calculated as λ55 Å. On the basis of experimental data analysis of electrophysical properties of both ZnSe/CuGaSe₂ heterojunctions and constituent materials the energetic band diagram of the investigated heterostructures is proposed. The current transport mechanism through ZnSe/CuGaSe₂ heterojunctions is consequently elucidated.