Three-dimensional metal gate-high-/spl kappa/-GOI CMOSFETs on 1-poly-6-metal 0.18-/spl mu/m Si devices

We demonstrate three-dimensional (3-D) self-aligned [IrO/sub 2/-IrO/sub 2/-Hf]-LaAlO/sub 3/-Ge-on-Insulator (GOI) CMOS FETs above 0.18-/spl mu/m Si CMOS FETs for the first time. At an equivalent oxide thickness of 1.4 nm, the 3-D IrO/sub 2/-LaAlO/sub 3/-GOI p-MOSFETs and IrO/sub 2/-Hf-LaAlO/sub 3/-GOI nMOSFETs show high hole and electron mobilities of 234 and 357 cm/sup 2//Vs respectively, without depredating the underneath 0.18-/spl mu/m Si devices. The hole mobility is 2.5 times higher than the universal mobility, at 1 MV/cm effective electric field. These promising results are due to the low-temperature GOI device process, which is well-matched to the low thermal budget requirements of 3-D integration. The high-performance GOI devices and simple 3-D integration process, compatible to current very large-scale integration (VLSI) technology, should be useful for future VLSI.     

A CMOS voltage reference based on weighted /spl Delta/V/sub GS/ for CMOS low-dropout linear regulators

A CMOS voltage reference, which is based on the weighted difference of the gate-source voltages of an NMOST and a PMOST operating in saturation region, is presented. The voltage reference is designed for CMOS low-dropout linear regulators and has been implemented in a standard 0.6-/spl mu/m CMOS technology (V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C). The occupied chip area is 0.055 mm/sup 2/. The minimum supply voltage is 1.4 V, and the maximum supply current is 9.7 /spl mu/A. A typical mean uncalibrated temperature coefficient of 36.9 ppm//spl deg/C is achieved, and the typical mean line regulation is /spl plusmn/0.083%/V. The power-supply rejection ratio without any filtering capacitor at 100 Hz and 10 MHz are -47 and -20 dB, respectively. Moreover, the measured noise density with a 100-nF filtering capacitor at 100 Hz is 152 nV//spl radic/(Hz) and that at 100 kHz is 1.6 nV//spl radic/(Hz).     

SODEL FET: novel channel and source/drain profile engineering schemes by selective Si epitaxial growth technology

In this paper, novel channel and source/drain profile engineering schemes are proposed for sub-50-nm bulk CMOS applications. This device, referred to as the silicon-on-depletion layer FET (SODEL FET), has the depletion layer beneath the channel region, which works as an insulator like a buried oxide in a silicon-on-insulator MOSFET. Thanks to this channel structure, junction capacitance (C/sub j/) has been reduced in SODEL FET, i.e., C/sub j/ (area) was /spl sim/0.73 fF//spl mu/m/sup 2/ both in SODEL nFET and pFET at Vbias =0.0 V. The body effect coefficient /spl gamma/ is also reduced to less than 0.02 V/sup 1/2/. Nevertheless, current drives of 886 /spl mu/A//spl mu/m (I/sub off/=15 nA//spl mu/m) in nFET and -320 /spl mu/A//spl mu/m (I/sub off/=10 nA//spl mu/m) in pFET have been achieved in 70-nm gate length SODEL CMOS with |V/sub dd/|=1.2 V. New circuit design schemes are also proposed for high-performance and low-power CMOS applications using the combination of SODEL FETs and bulk FETs on the same chip for 90-nm-node generation and beyond.     

Process and Device Performance of Submicrometer-Channel CMOS Devices Using Deep-Trench Isolation and Self-Aligned TiSi/sub 2/ Technologies

According to our scaling study, a deeper n-well allows for a lower n-well surface concentration with improved short-channel effects in submicrometer-channel PMOS-FET's. The deep n-well, however, requires a large space between n- and p-channel devices. This large space limits the integration density in scaled bulk CMOS VLSI's. The deep-trench isolation combined with an epitaxial layer resolves this drawback with significantly improved device-to-device isolation and latchup susceptibility. The 6-/spl mu/m-deep with 2-/spl mu/m-wide deep trench is etched in the epitaxial layer and is refilled with 1500 /spl Aring/ of thermal silicon-dioxide film and 2/spl mu/m of polysilicon film. The sheet resistances of N/sup +/ and P/sup +/ diffusion and N/sup +/ -doped polysilicon layers were reduced to 3 to 4 /spl Omega//spl square/ by using the self-aligned TiSi/sub 2/ layer with an oxide sidewall spacer. As a result of this low sheet resistance, the saturation drain current of submicrometer n- and p-channel MOSFET's was improved approximately 33 to 37 percent compared with conventional MOSFET's without the self-aligned TiSi/sub 2/ layer. The 0.5-/spl mu/m-channel CMOS devices using the deep-trench isolation with an epitaxial layer and the self-aligned TiSi/sub 2/ layer operated at a propagation delay time of 140 ps with a power dissipation of 1.1 mW per inverter and attained a maximum clock frequency of 400 MHz in a static /spl divide/ 4 counter without suffering from Iatchup even at the Iatchup trigger current of 200 mA.     

DRAM plate electrode bias optimization for reducing leakage current in UV-O/sub 3/ and O/sub 2/ annealed CVD deposited Ta/sub 2/O/sub 5/ dielectric films

A new plate biasing scheme is described which allowed the use of 65% higher supply voltage without increasing the leakage current for the UV-O/sub 3/ and O/sub 2/ annealed chemical-vapor-deposited tantalum pentaoxide dielectric film capacitors in stacked DRAM cells. Dielectric leakage was reduced by biasing the capacitor plate electrode to a voltage lower than the conventionally used value of V/sub cc//2. Ta/sub 2/O/sub 5/ films with 3.9 nm effective gate oxide, 8.5 fF//spl mu/m/sup 2/ capacitance and <0.3 /spl mu/A/cm/sup 2/ leakage at 100/spl deg/C and 3.3 V supply are demonstrated.<>     

Analysis of the gate-source/drain capacitance behavior of a narrow-channel FD SOI NMOS device considering the 3-D fringing capacitances using 3-D simulation

This paper reports an analysis of the gate-source/drain capacitance behavior of a narrow-channel fully depleted (FD) silicon-on-insulator (SOI) NMOS device considering the three-dimensional (3-D) fringing capacitances. Based on the 3-D simulation results, when the width of the FD SOI NMOS device is scaled down to 0.05 /spl mu/m, the inner-sidewall-oxide fringing capacitance (C/sub FIS/), due to the fringing electric field at the edge of the mesa-isolated structure of the FD SOI NMOS device biased at V/sub G/=0.3 V and V/sub D/=1 V, is the second largest contributor to the gate-source capacitance (C/sub GS/). Thus, when using nanometer CMOS devices with a channel width smaller than 0.1 /spl mu/m, C/sub FIS/ cannot be overlooked for modeling gate-source/drain capacitance (C/sub GS//C/sub GD/).     

Electrical characteristics and reliability of UV transparent Si/sub 3/N/sub 4/ metal-insulator-metal (MIM) capacitors

In this paper, we discuss the electrical characteristics and reliability of UV transparent Si/sub 3/N/sub 4/ metal-insulator-metal (MIM) capacitors. We examine film thicknesses in the range of 55 to 25 nm with capacitance densities from 1.2 ff//spl mu/m/sup 2/ to 2.8 ff//spl mu/m/sup 2/, respectively, for single MIM capacitors. A new approach for projecting the dielectric reliability of these films extends the limits of maximum operating voltage. Accounting for temperature acceleration and area scaling, the projected lifetimes can be met for a wide range of operating conditions.     

A 60-mW 200-MHz continuous-time seventh-order linear phase filter with on-chip automatic tuning system

A full CMOS seventh-order linear phase filter based on g/sub m/-C biquads with a -3-dB frequency of 200 MHz is realized in 0.35-/spl mu/m CMOS process. The linear operational transconductance amplifier is based on complementary differential pairs in order to achieve both low-distortion figures and high-frequency operation. The common-mode feedback (CMFB) employed takes advantage of the filter architecture; incorporating the load capacitors into the CMFB loop improves further its phase margin. A very simple automatic tuning system corrects the filter deviations due to process parameter tolerances and temperature variations. The group delay ripple is less than 5% for frequencies up to 300 MHz, while the power consumption is 60 mW. The third-harmonic distortion is less than -44 dB for input signals up to 500 mV/sub pp/. The filter active area is only 900 /spl times/ 200 /spl mu/m/sup 2/. The supply voltages used are /spl plusmn/1.5 V.     

Quantum-efficiency measurements in oxygen-containing gallium lanthanum sulphide glasses and fibers doped with Pr/sup 3+/

The production of competitive fiber amplifiers in the 1.3-/spl mu/m region requires both good quantum efficiency in the lasing ion and the capability to produce low-loss fibers. Oxygen-doped gallium lanthanum sulphide (GLS) doped with Pr/sup 3+/ may provide a route to both, We describe measurements of the quantum efficiency of Pr/sup 3+/ emission at 1.3 /spl mu/m from the /sup 1/G/sub 4/-/sup 3/H/sub 5/ transition in GLS glass and fiber containing varying quantities of lanthanum oxide. We show that oxide-containing GLS glasses, which are known to have considerably better thermal and glass-forming properties than pure GLS, can show quantum efficiencies of up to 84% of that of pure GLS, No degradation of quantum efficiency is seen when oxide-containing GLS glass is pulled into fiber form.     

Three-dimensional integration: technology, use, and issues for mixed-signal applications

Three-dimensional (3-D) integration provides opportunities in large-scale integration of mixed-signal and general system-on-chip applications with improved performance, through increased density and mixing of different active and passive technologies. This paper reports a novel low-thermal-budget 3-D fabrication technique-multilayers with buried structures (MLBS) and an analysis of its applicability to mixed-signal integration. The MLBS technique uses a low temperature of 450/spl deg/C to transfer a single-crystal silicon layer over a processed wafer consisting of buried in-plane and out-of-plane interconnects obtained through a dual Damascene process. Devices can continue to be processed on this transferred layer. Electrical characteristics of MOS capacitors (D/sub it/=4.7/spl times/10/sup 10/ cm/sup -2/ eV/sup -1/) and 3-D integrated planar CMOS transistors (3-D CMOS), fabricated using MLBS, are consistent with integration requirements. Our analog analysis includes an investigation of thermal effects important to analog applications with continuous operation of transistors in forward active bias, as well as of the coupling isolation derived from use of a ground-plane. Use of high density local interconnectivity improves the thermal properties of 3-D CMOS over that of silicon-on-insulator, and use of a ground plane is shown to lead to an improvement of better than 8 dB in coupling isolation.     

A 2-V 23-/spl mu/A 5.3-ppm//spl deg/C curvature-compensated CMOS bandgap voltage reference

A high-order curvature-compensated CMOS bandgap reference, which utilizes a temperature-dependent resistor ratio generated by a high-resistive poly resistor and a diffusion resistor, is presented in this paper. Implemented in a standard 0.6-/spl mu/m CMOS technology with V/sub thn//spl ap/|V/sub thp/|/spl ap/0.9 V at 0/spl deg/C, the proposed voltage reference can operate down to a 2-V supply and consumes a maximum supply current of 23 /spl mu/A. A temperature coefficient of 5.3 ppm//spl deg/C at a 2-V supply and a line regulation of /spl plusmn/1.43 mV/V at 27/spl deg/C are achieved. Experimental results show that the temperature drift is reduced by approximately five times when compared with a conventional bandgap reference in the same technology.     

A new metal-ferroelectric (PbZr/sub 0.53/Ti/sub 0.47/O/sub 3/)-insulator (Dy/sub 2/O/sub 3/)-semiconductor (MFIS) FET for nonvolatile memory applications

Metal-ferroelectric-insulator-semiconductor (MFIS) field-effect transistors with Pb(Zr/sub 0.53/,Ti/sub 0.47/)O/sub 3/ ferroelectric layer and dysprosium oxide Dy/sub 2/O/sub 3/ insulator layer were fabricated. The out-diffusion of atoms between Dy/sub 2/O/sub 3/ and silicon was examined by secondary ion mass spectrometry profiles. The size of the memory windows was investigated. The memory windows measured from capacitance-voltage curves of MFIS capacitors and I/sub DS/-V/sub GS/ curves of MFIS transistors are consistent. The nonvolatile operation of MFIS transistors was demonstrated by applying positive/negative writing pulses. A high driving current of 9 /spl mu/A//spl mu/m was obtained even for long-channel devices with a channel length of 20 /spl mu/m. The electron mobility is 181 cm/sup 2//V/spl middot/s. The retention properties of MFIS transistors were also measured.     

Reliability investigation of 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel

The authors have investigated the reliability performance of G-band (183 GHz) monolithic microwave integrated circuit (MMIC) amplifiers fabricated using 0.07-/spl mu/m T-gate InGaAs-InAlAs-InP HEMTs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel on 3-in wafers. Life test was performed at two temperatures (T/sub 1/ = 200 /spl deg/C and T/sub 2/ = 215 /spl deg/C), and the amplifiers were stressed at V/sub ds/ of 1 V and I/sub ds/ of 250 mA/mm in a N/sub 2/ ambient. The activation energy is as high as 1.7 eV, achieving a projected median-time-to-failure (MTTF) /spl ap/ 2 /spl times/ 10/sup 6/ h at a junction temperature of 125 /spl deg/C. MTTF was determined by 2-temperature constant current stress using /spl Delta/G/sub mp/ = -20% as the failure criteria. The difference of reliability performance between 0.07-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with pseudomorphic In/sub 0.75/Ga/sub 0.25/As channel and 0.1-/spl mu/m InGaAs-InAlAs-InP HEMT MMICs with In/sub 0.6/Ga/sub 0.4/As channel is also discussed. The achieved high-reliability result demonstrates a robust 0.07-/spl mu/m pseudomorphic InGaAs-InAlAs-InP HEMT MMICs production technology for G-band applications.     

Effect of annealing on GaN-insulator interfaces characterized by metal-insulator-semiconductor capacitors

GaN metal-oxide-semiconductor (MOS) capacitors have been used to characterize the effect of annealing temperature and ambient on GaN-insulator interface properties. Silicon dioxide was deposited on n-type GaN at 900 /spl deg/C by low-pressure chemical vapor deposition and MOS capacitors were fabricated. The MOS capacitors were used to characterize the GaN-SiO/sub 2/ interface with a low interface-state density of 3 /spl times/ 10/sup 11/ cm/sup -2/eV/sup -1/ at 0.25 eV below the conduction band edge, even after annealing in N/sub 2/ at temperatures up to 1100 /spl deg/C; however, insulator properties were degraded by annealing in NO and NH/sub 3/ at 1100 /spl deg/C.     

Efficient PDFA module using high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber

The highest reported single-pass gain coefficient of 0.36 dB/mW has been achieved using a newly developed Pr/sup 3+/-doped high-NA PbF/sub 2//InF/sub 3/-based fluoride fiber, with a /spl Delta/n of 6.6%, a core diameter of 1.2 /spl mu/m and a transmission loss of 250 dB/km at 1.2 /spl mu/m. This fiber was used to construct an efficient PDFA module with a MOPA-LD. A small-signal net gain of 22.5 dB was achieved at 1.30 /spl mu/m with a pump power of 23m mW.     

1.5-V single work-function W/WN/n/sup +/-poly gate CMOS device design with 110-nm buried-channel PMOS for 90-nm vertical-cell DRAM

This letter reports on 1.5-V single work-function W/WN/n/sup +/-poly gate CMOS transistors for high-performance stand-alone dynamic random access memory (DRAM) and low-cost low-leakage embedded DRAM applications. At V/sub dd/ Of 1.5-V and 25/spl deg/C, drive currents of 634 /spl mu/A//spl mu/m for 90-nm L/sub gate/ NMOS and 208 /spl mu/A-/spl mu/m for 110-nm L/sub gate/ buried-channel PMOS are achieved at 25 pA//spl mu/m off-state leakage. Device performance of this single work function technology is comparable to published low leakage 1.5-V dual work-function technologies and 25% better than previously reported 1.8-V single work-function technology. Data illustrating hot-carrier immunity of these devices under high electric fields is also presented. Scalability of single work-function CMOS device design for the 90-nm DRAM generation is demonstrated.     

Evidence and understanding of ALD HfO/sub 2/-Al/sub 2/O/sub 3/ laminate MIM capacitors outperforming sandwich counterparts

Metal-insulator-metal capacitors with atomic-layer-deposited HfO/sub 2/-Al/sub 2/O/sub 3/ laminated and sandwiched dielectrics have been compared, for the first time, for analog circuit applications. The experimental results indicate that significant improvements can be obtained using the laminated dielectrics, including an extremely low leakage current of 1/spl times/10/sup -9/ A/cm/sup 2/ at 3.3V and 125/spl deg/C, a high breakdown electric field of /spl sim/3.3MV/cm at 125/spl deg/C, good polarity-independent electrical characteristics, while retaining relatively high capacitance density of 3.13 fF//spl mu/m/sup 2/ as well as voltage coefficients of capacitance as low as -80 ppm/V and 100 ppm/V/sup 2/ at 100 kHz. The underlying mechanism is likely due to alternate insertions of Al/sub 2/O/sub 3/ layers that reduce the thickness of each HfO/sub 2/ layer, hereby efficiently inhibiting HfO/sub 2/ crystallization, and blocking extensions of grain boundary channels from top to bottom as well as to achieve good interfacial quality.     

Superlattice microrefrigerators fusion bonded with optoelectronic devices

A three-dimensional (3-D) electrothermal model was developed to study the InP-based thin-film In/sub 0.53/Ga/sub 0.47/As/In/sub 0.52/Al/sub 0.48/As superlattice (SL) microrefrigerators for various device sizes, ranging from 40/spl times/40 to 120/spl times/120/spl mu/m /sup 2/. We discussed both the maximum cooling and cooling power densities (CPDs) for experimental devices, analyzed their nonidealities, and proposed an optimized structure. The simulation results demonstrated that the experimental devices with an optimized structure can achieve a maximum cooling of 3/spl deg/C, or equivalently, a CPD over 300W/cm/sup 2/. Furthermore, we found it was possible to achieve a maximum cooling of over 10/spl deg/C; equivalently, a CPD over 900W/cm/sup 2/, when the figure of merit (ZT) of InGaAs/InAlAs SL was enhanced five times with nonconserved lateral momentum structures. Besides monolithic growth, we also proposed a fusion bonding scheme to simply bond the microrefrigerator chip on the back of the hot spots, defined as two-chip integration model in this paper. The cooling effect of this model was analyzed using ANSYS simulations.     

High-performance MIM capacitor using ALD high-k HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectrics

For the first time, we successfully fabricated and demonstrated high performance metal-insulator-metal (MIM) capacitors with HfO/sub 2/-Al/sub 2/O/sub 3/ laminate dielectric using atomic layer deposition (ALD) technique. Our data indicates that the laminate MIM capacitor can provide high capacitance density of 12.8 fF//spl mu/m/sup 2/ from 10 kHz up to 20 GHz, very low leakage current of 3.2 /spl times/ 10/sup -8/ A/cm/sup 2/ at 3.3 V, small linear voltage coefficient of capacitance of 240 ppm/V together with quadratic one of 1830 ppm/V/sup 2/, temperature coefficient of capacitance of 182 ppm//spl deg/C, and high breakdown field of /spl sim/6 MV/cm as well as promising reliability. As a result, the HfO/sub 2/-Al/sub 2/O/sub 3/ laminate is a very promising candidate for next generation MIM capacitor for radio frequency and mixed signal integrated circuit applications.     

A 0.18-/spl mu/m RF SiGe BiCMOS technology with collector-epi-free double-poly self-aligned HBTs

This paper describes an RF SiGe BiCMOS technology based on a standard 0.18-/spl mu/m CMOS process. This technology has the following key points: 1) A double-poly self-aligned SiGe-HBT is produced by adding a four-mask process to the CMOS process flow-this HBT has an SiGe epitaxial base selectively grown on an epi-free collector; 2) two-step annealing of CMOS source/drain/gate activation is utilized to solve the thermal budget tradeoff between SiGe-HBTs and CMOS; and 3) a robust Ge profile design is studied to improve the thermal stability of the SiGe-base/Si-collector junction. This process yields 73-GHz f/sub T/, 61-GHz f/sub max/ SiGe HBTs without compromising 0.18-/spl mu/m p/sup +//n/sup +/ dual-gate CMOS characteristics.