2205双相不锈钢的高温变形行为研究

在Gleeble-1500热模拟试验机上进行热-力模拟试验,得到实验数据并分析试样的热塑性、变形抗力,并利用金相显微镜对其进行金相组织的分析。在950~1 200℃温度区间进行高温拉伸试验,绘制出样品的热塑性曲线与热强度曲线,通过热塑性曲线说明在950~1 200℃范围内具有良好的塑性,通过热强度曲线可以观察到屈服强度随温度的升高而降低;在变形温度为950~1 200℃,应变速率为0.1,1,5和10 s-1时进行高温压缩试验,绘制出真应力-应变曲线和变形抗力曲线,结果显示,变形抗力随应变量的增大而迅速达到最大值,而后趋于平缓,随着温度的升高,变形抗力呈下降的趋势。     

双相不锈钢热塑性的研究

本文采用落锤试验法，研究了在不同试验温度下镍、氮合金元素含量和α／γ两相比例对高铬镍双相不锈钢热塑性的影响。     

提高双相不锈钢热塑性的实践

在国外双相不锈钢管的制造是通过热挤压的方法。而国内绝大多数制管企业采用两辊斜轧穿孔的方法来获得毛管,由于变形剧烈,对钢的热塑性要求甚高,为了适应这种情况,必须提高双相不锈钢热塑性。本文介绍了添加微量元素、铁素体控制等方法而获得的效果,即使超级双相不锈钢S32750在1180℃?1200℃ Gleeble热模拟试验,其断面收缩率也高达97%,热塑性大大提高,可顺利通过热穿孔。     

2507超级双相不锈钢的热变形行为

用MMS-200热模拟实验机对2507超级双相不锈钢(/%:0.022C、0.58Si、25.35Cr、7.17Ni、4.05Mo、0.28N)12 mm热轧板在1 000～1150℃、应变速率0.01～10s^-1下进行了热压缩实验。实验结果表明,在应变速率一定的条件下,变形温度越高,2507超级双相不锈钢峰值应力越低;在变形温度一定的条件下,峰值应力随着应变速率的增加而增加。根据热变形方程计算得到压缩变形时的平均表观应力指数n=3.25,热变形激活能Q=460kJ/mol。基于实验数据构建了2507超级双相不锈钢在相应变形条件下的热变形方程。     

双相不锈钢S32101生产工艺研究

从成分控制、热轧和热处理等角度出发,综合研究双相不锈钢S32101的生产工艺并进行优化调整,分析生产试验数据。研究分析表明：在1050～1150℃固溶处理时,组织中铁索体组织与奥氏体组织的比例接近1：1,钢的综合力学性能最佳。     

双相不锈钢热变形后的静态软化行为及组织分析

在MMS-200热模拟试验机上,采用不同道次压缩法研究了00Cr22Ni5Mo3N双相不锈钢的高温热变形行为,从双道次压缩试验数据中得到不同温度条件下的软化率曲线,并对变形显微组织进行了分析。结果表明：在1~400 s道次间隔时间内,软化率随时间延长而增加,在100 s之内基本完成静态软化。变形温度越高,静态软化行为越...     

Investigation of the Hot Plasticity of Duplex Stainless Steel

Hot plasticity of a nitrogen alloyed 25Cr 7Ni-4Mo duplex stainless steel was investigated. The results indicate that the main factors affecting the hot plasticity of duplex stainless steel are listed as follows： coalescent force of phase interface, microstructure, and the phase ratio and difference between the mechanical properties of ferrite and austenite. The heat treatment and sulphur contents have a notable effect on the hot plasticity. The reasonable heat treatments and the increased interfacial coalescent force will effectively enhance the hot plasticity of duplex stainless steel.     

高应变率下00Cr23Ni4N双相不锈钢的热变形行为

 采用Gleeble-3800热力学模拟试验机对00Cr23Ni4N双相不锈钢进行了高温压缩试验,研究了其在900～1150℃、5～50s-1条件下的热变形行为,并利用Sellars双曲正弦模型建立了峰值流变应力与Zener-Hollomon（Z参数）之间的关系。研究结果表明,00Cr23Ni4N双相不锈钢的高温流变应力随变形温度的升高、应变速率的减小显著降低;在变形温度为1100～1150℃,材料均表现出良好的热加工性能;通过回归分析,00Cr23Ni4N双相不锈钢的应力指数为2.6,热变形激活能为263.4kJ/mol,Z参数能较好地描述该钢种的流变行为。     

Effects of Temperature and Strain Rate on Flow Behavior and Microstructural Evolution of Super Duplex Stainless Steel under Hot Deformation

Hot compression tests were carried out in the temperature range of 1 223-1 473 Kand strain rate range of0.01-30s-1 to investigate the flow behavior and microstructural evolution of super duplex stainless steel 2507(SDSS2507).It is found that most of the flow curves exhibit a characteristic of dynamic recrystallization(DRX)and the flow stress increases with the decrease of temperature and the increase of strain rate.The apparent activation energy Qof SDSS2507 with varying true strain and strain rate is determined.As the strain increases,the value of Qdeclines in different ways with varying strain rate.The microstructural evolution characteristics and the strain partition between the two constituent phases are significantly affected by the Zener-Hollomon parameter(Z).At a lower lnZ,dynamic recovery(DRV)and continuous dynamic recrystallization(CDRX)of the ferrite dominate the softening mechanism during the compression.At this time,steady state deformation takes place at the last stage of deformation.In contrast,a higher lnZ will facilitate the plastic deformation of the austenite and then activate the discontinuous dynamic recrystallization(DDRX)of the austenite,which leads to a continuous decline of the flow stress even at the last deformation stage together with CDRX of the ferrite.     

双相不锈钢2205的热加工性能研究

研究了双相不锈钢2205在1 000~1 200℃温度、应变速率0.01~30 s-1下压缩变形的热加工行为。讨论了该条件下的应力应变曲线的特征并根据sinh-Arrhenius方程计算了其形变激活能为519 KJ/mol。通过对试样的金相及TEM观察,讨论了双相不锈钢中的奥氏体相和铁素体相在热变形中的回复、再结晶机制。     

双相不锈钢2205铸态组织的热变形研究

研究了工业连铸双相不锈钢2205在不同温度和应变速率下的热变形过程。通过单道次热模拟压缩试验分析了铸态2205流变应力与温度和应变速率的关系,计算出铸态2205的热变形激活能Q=599 kJ/mol,说明铸态2205热加工性能较差。组织分析显示,两相之间变形不协调是相界微裂纹产生的根本原因。     

Chi Phase after Short-term Aging and Corrosion Behavior in 2205 Duplex Stainless Steel

Correlation between pitting corrosion behavior and chi( χ )phase formed after a short-term aging(5,10 and 15 min)at 850 ℃ of 2205 duplex stainless steel(DSS)was investigated using potentiodynamic polarization tests,optical microscopy,and scanning electron microscopy equipped with energy-dispersive spectrum system.Results showed that after aging for 5min,the χ phase initially precipitated at ferrite grain boundaries,developed and then became linked with prolonging aging time.The χ phase was rich in Cr and Mo,resulting in formation of depleted zones nearby.The χ phase could reduce corrosion resistance of DSS and slightly influence its stability,but the specimens still displayed the capacity for repassivation.Some lines of evidence showed that stable pitting corrosion initiated at the boundaries of precipitates.The χ phase was selectively corroded during the first stage of corrosion and then the depleted zones nearby were attacked.In addition,the grain size and volume of precipitates also affected pit nucleation and progress,and suitable size and distribution of χ phase could aggravate pit initiation at precipitate boundaries.The χ phase with considerably low volume fraction and small size was not sensitive position for pit initiation.     

σ相的析出对双相不锈钢组织性能的影响

σ相是一种富Cr、Mo的金属间化合物,它的存在会使钢的强度提高,塑韧性降低,恶化耐蚀性能。主要从成分、组织、性能等方面对S31803、S32750双相不锈钢σ相的析出行为进行研究。结果表明：Cr、Mo增加了σ相析出的敏感性,而且随时效时间的延长,σ相析出的数量不断增加;而且σ相的析出对材料的塑性、耐蚀性都造成不利影响。