异质双碳源对LiMn0.8Fe0.2PO4复合材料电化学性能的影响

采用水基流变相辅助的固相法,以异质碳蔗糖和石墨为碳源,合成了LiMn_0.8Fe_0.2PO₄/C复合材料,研究了不同石墨加入方式对所制复合材料电化学性能的影响,并对所制备的LiMn_0.8Fe_0.2PO₄/C复合材料进行了X射线衍射(XRD)、N₂吸附-脱附测试、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等表征。结果表明,不同石墨包覆工艺对材料结构和电化学性能具有显著影响。前驱体煅烧后再加入石墨获得的样品纯度高,形貌呈均一的椭圆形,在0.1C下的放电比容量为149 mAh·g^-1,达到其理论比容量的87%;在5C下最大的放电比容量为133 mAh·g^-1;在2C倍率下经过300次循环后比容量维持在127 mAh·g^-1,衰减率仅为1.9%,表现出了优良的循环稳定性。     

锂离子电池用Sn/C复合材料的碳热还原法制备

采用碳热还原法制备了Sn/C复合材料,通过XRD、SEM、恒流充放电循环、慢速扫描循环伏安(CV)等方法对材料以及其电化学嵌脱锂性能做了研究。结果表明：Sn球均匀分散在絮状碳材料中,加热时间越长,Sn球粒径越大。加热8 h得到材料的首次嵌锂比容量可达1 014 mAh·g^-1,循环15周以后的嵌锂比容量为406 mAh·g^-1。     

钽离子掺杂对LiFePO4 / C物理和电化学性能的影响

采用PAM(聚丙烯酰胺)模板-溶胶凝胶法在惰性气氛下合成钽掺杂的LiFePO₄/C复合正极材料，考察了钽对目标化合物的物理和电化学性能的影响。研究结果表明，0.33C的电流下充放电时，掺杂前后第2个循环的放电容量分别为138.6 mAh·g^-1和155.5 mAh·g^-1，循环20次后容量为141 mAh·g^-1和156 mAh·g^-1。电化学交流阻抗表明，掺杂后的材料阻抗R_ct从180 Ω减小到120 Ω。振实密度比掺杂前提高0.312 g·cm^-3。     

高温固相法合成LiNi1/3Mn1/3Co1/3O2及其性能研究

采用高温固相法合成出层状锂离子电池正极材料LiNi_1/3Mn_1/3Co_1/3O₂。通过XRD、ICP、SEM和电化学测试手段对产物的结构、组成、形貌及电化学性能进行了研究。XRD结果表明此方法合成的LiNi_1/3Mn_1/3Co_1/3O₂具有标准的α-NaFeO₂型层状结构，SEM照片显示颗粒粒径大约在500 nm左右，粒径分布较窄。以20 mA·g^-1电流密度放电，充放电电压在2.8～4.4 V之间，其首次放电比容量为170 mAh·g^-1，40次循环容量保持率为85.3%。进一步加入石墨导电剂后，同样条件下首次放电比容量变为179 mAh·g^-1，50次循环容量保持率为89.6%。容量衰减主要发生在前10次循环。XRD和SEM测试表明循环初期容量衰减的原因是由材料本体结构变化和界面反应共同作用的结果。     

双金属(Sn/Ni)掺杂多孔硅微球的液相合成与电化学储锂性能

使用廉价的硅铝合金前驱体,通过简单的化学沉积方法制备了新型双金属(Sn/Ni)掺杂多孔硅微球(pSi@SnNi)。pSi@SnNi复合材料的三维多孔结构可以缓冲硅在锂化过程中的巨大体积膨胀,增加储锂活性位点。双金属(Sn/Ni)的掺杂可以提高硅的电子导电性,改进pSi的结构稳定性。由于其独特的组成和微观结构,具有适当Sn/Ni含量的pSi@SnNi复合材料显示了较大的可逆储锂容量(0.1 A·g^-1下为2 651.7 mAh·g^-1)、较高的电化学循环稳定性(1 A·g^-1下400次循环后为1 139 mAh·g^-1)和优异的倍率性能(2.5 A·g^-1下为1 235.8 mAh·g^-1)。     

层状LiCo1/3Ni1/3Mn1/3O2正极材料的合成及电化学性能研究

采用液相法在800 ℃空气中烧结20 h合成出层状LiCo_1/3Ni_1/3Mn_1/3O₂正极材料。通过XRD、IR、SEM、XPS和电化学性能测试考察了产物的组成、结构、形貌及电化学性能。结果表明，所合成的LiCo_1/3Ni_1/3Mn_1/3O₂为六方单相，层状结构发育完善；产物呈球形且粒度小，分布窄，平均粒径为0.3 μm。以1 mA·cm^-2的电流密度，在2.7～4.3 V区间进行充放电测试，前4周的充放电比容量分别为168/160 mAh·g^-1、169/162 mAh·g^-1、165/160 mAh·g^-1、163/158 mAh·g^-1，循环性能优良。循环伏安实验表明，该材料在3.9 V附近出现了一对对称性好的氧化还原峰。     

ZnS@C/rGO复合材料的制备及其电化学可逆储锂性能

通过溶剂热反应-水热处理的途径,制备了无定形碳包覆的ZnS纳米晶体（ZnS@C）与还原氧化石墨烯（rGO）复合的ZnS@C/rGO复合材料,并用X射线衍射（XRD）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）和X射线光电子能谱（XPS）对复合材料进行了形貌和微观结构的表征。电化学测试结果表明,与ZnS@C和ZnS/rGO相比,所制备的ZnS@C/rGO复合材料显示了显著增强的电化学储锂性能,在100 mA·g^-1电流密度下,其电化学储锂的首次可逆比容量为1 101 mAh·g^-1,充放电循环100次后其可逆比容量为1 569 mAh·g^-1。在不同电流密度下循环1 200次后,仍保持在2.0 A·g^-1电流密度下有1 096 mAh·g^-1的可逆比容量,显示了其稳定的长循环性能。     

纳米CoSe修饰氮掺杂多孔碳的可控制备及其锂硫电池多硫化物的催化转化效应

锂硫电池中较差的循环稳定性和倍率性能是实现锂硫电池商业化的技术障碍,其主要原因之一是多硫化物在硫电极内的电化学转化动力学较为缓慢。为此,我们以ZIF-9为前驱体,采用先碳化,再酸化刻蚀,最后硒化的方法合成了含少量催化剂的CoSe修饰氮掺杂多孔碳(CoSe/NC)电极材料,以期提高硫电极内多硫化物的电化学转化动力学性能,并通过流动液相三电极体系对该材料进行电化学动力学表征。结果显示,相较于对比材料,CoSe/NC能够加快多硫化物的氧化还原反应速率,在 0.2mA·cm^-2电流密度下,多硫化物氧化还原反应在CoSe/NC电极上有最小的反应过电位;同时,在0.1 V过电位下,各氧化还原反应也有最大的响应电流。因此,将 CoSe/NC作为硫宿主材料组装电池展现了优异的电化学性能：在 1C(1C=1 675 mA·g^-1)下初始放电比容量为1 068 mAh·g^-1,经过500次循环后,可逆容量仍保持在693 mAh·g^-1。另外,在3C的高电流密度下,放电比容量可高达819 mAh·g^-1。     

负极材料NiO的制备及电化学性能

以Ni(NO₃)₂·6H₂O和NaOH为原料,采用水热法合成了锂离子电池负极材料NiO。通过TG-DSC分析，确定了合成过程的反应机理。通过XRD、SEM和恒流充放电测试,研究了NiO样品的结构、形貌及电化学性能。400 ℃焙烧得到立方结构的NiO产品，以0.10 mA·cm^-2充放电,首次放电比容量达到1 151 mAh·g^-1，经过20次循环后的比容量仍为776 mAh·g^-1。     

微乳液法合成LiFePO4 / C正极材料及其电化学性能

本文采用微乳液方法合成了纳米LiFePO₄ / C正极材料。制备样品分别用XRD和SEM进行表征，充放电测试其电化学性能。600 ℃制备样品为单一物相，平均粒径90 nm，在室温2.0～4.0 V (vs Li) 放电电压范围和15 mA·g^-1放电速率下，首次放电容量达到159 mAh·g^-1。制备样品同样展现良好的循环性能。在15 mA·g^-1速率下40次循环后，制备样品放电容量仍保持首次放电容量的98.9%。优异的电化学性能得益于样品颗粒的纳米尺寸、均匀分布以及表面碳层包覆提高了活性材料的电子电导率。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.