Dynamically cured PP/MAH-g-SEBS/epoxy blends

Abstract

A new method concerning the simultaneous reinforcing and toughening of polypropylene (PP) is reported. Dynamic cure of the epoxy resin with 2-ethylene-4-methane-imidazole was successfully applied in the PP/maleic anhydride grafted styrene–ethylene–butylene–styrene (MAH-g-SEBS) triblock co-polymer, and the obtained blends were named as dynamically cured PP/MAH-g-SEBS/epoxy blends. The stiffness and toughness of the blends are in a good balance, and the smaller size of the epoxy particle in the PP/MAH-g-SEBS/epoxy blends shows that MAH-g-SEBS was also used as a compatibiliser. The structure of the dynamically cured PP/MAH-g-SEBS/epoxy blends is the embedding of the epoxy particles by MAH-g-SEBS. The cured epoxy particles as organic filler increase the stiffness of the PP/MAH-g-SEBS blends, and the improvement in the toughness is attributed to the embedded structure. The tensile strength and flexural modulus of the blends increase with increasing epoxy resin content, and the impact strength reaches a maximum of 342 J m^?1 at the epoxy resin content of 10wt-%. Differential scanning calorimetry analysis shows that the epoxy particles in the dynamically cured PP/MAH-g-SEBS/epoxy blends could have contained embedded MAH-g-SEBS, decreasing the nucleating effect of the epoxy resin. Wide angle X-ray diffraction analysis shows that the dynamical cure and compatibilisation do not disturb the crystalline structure of PP in the blends.     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Study of dynamically cured PP/MAH‐g‐PP/talc/epoxy composites

In the present study, an epoxy resin was dynamically cured in a polypropylene (PP)/maleic anhydride–grafted PP (MAH‐g‐PP)/talc matrix to prepare dynamically cured PP/MAH‐g‐PP/talc/epoxy composites. An increase in the torque at equilibrium showed that epoxy resin in the PP/MAH‐g‐PP/talc composites had been cured by 2‐ethylene‐4‐methane‐imidazole. Scanning electron microscopy analysis showed that MAH‐g‐PP and an epoxy resin had effectively increased the interaction adhesion between PP and the talc in the PP/talc composites. Dynamic curing of the epoxy resin further increased the interaction adhesion. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had higher crystallization peaks than did the PP/talc composites. Thermogravimetric analysis showed that the addition of MAH‐g‐PP and the epoxy resin into the PP/talc composites caused an obvious improvement in the thermal stability. The dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best thermal stability of all the PP/talc composites. The PP/MAH‐g‐PP/talc/epoxy composites had better mechanical properties than did the PP/MAH‐g‐PP/talc composites, and the dynamically cured PP/MAH‐g‐PP/talc/epoxy composites had the best mechanical properties of all the PP/talc composites, which can be attributed to the better interaction adhesion between the PP and the talc. The suitable content of epoxy resin in the composites was about 5 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Rheological behavior of polypropylene/novolac blends

The rheological behavior of polypropylene/novolac blends was investigated with special reference to the effects of the blend ratio, compatibilization, and dynamic cure. The polypropylene and all the polypropylene/novolac blends presented evidence of shear‐thinning behavior. The novolac, compatibilizer, and dynamic cure had dramatic effects on the rheological behavior of the polypropylene. Various rheological plots, including plots of the viscosity, storage modulus, loss modulus, and loss angle, Han plots, and Cole–Cole plots, were used to analyze the polypropylene/novolac blends. The results showed that the compatibilization together with the dynamic cure could increase the viscosity and modulus because of the formation of a grafting polymer between the maleic anhydride grafted polypropylene and the curing novolac resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Crystallization behavior of carbon black‐filled polypropylene and polypropylene/epoxy composites

The crystallization behavior of polypropylene (PP)/carbon black (CB) and PP/epoxy/CB composites was studied with differential scanning calorimetry (DSC). The effects of compatibilizer MAH‐g‐PP and dynamic cure on the crystallization behavior are investigated. The nonisothermal crystallization parameters analysis showed that CB particles in the PP/CB composites and the dispersed epoxy particles in the PP/epoxy composites could act as nucleating agents, accelerating the crystallization of the composites. Morphological studies indicated that the incorporation of CB into PP/epoxy resulted in its preferential localization in the epoxy resin phase, changing the spherical epoxy particles into elongated structure, and thus reduced the nucleation effect of epoxy particles. Addition of MAH‐g‐PP significantly decreased the average diameter of epoxy particles in the PP/epoxy and PP/epoxy/CB composites, promoting the crystallization of PP more effectively. The isothermal crystallization kinetics and thermodynamics of the PP/CB and PP/epoxy/CB composites were studied with the Avrami equation and Hoffman theory, respectively. The Avrami exponent and the crystallization rate of the PP/CB composites were higher than those of PP, and the free energy of chain folding for PP crystallization decreased with increasing CB content. Addition of MAH‐g‐PP into the PP/epoxy and PP/epoxy/CB composites increased the crystallization rate of the composites and decreased the chain folding energy significantly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 104–118, 2006     

Compatibilization of polypropylene/nylon 6 blends with a polypropylene solid‐phase graft

The compatibilization of polypropylene (PP)/nylon 6 (PA6) blends with a new PP solid‐phase graft copolymer (gPP) was systematically studied. gPP improved the compatibility of PP/PA6 blends efficiently. Because of the reaction between the reactive groups of gPP and the NH₂ end groups of PA6, a PP‐g‐PA6 copolymer was formed as a compatibilizer in the vicinity of the interfaces during the melting extrusion of gPP and PA6. The tensile strength and impact strength of the compatibilized PP/PA6 blends obviously increased in comparison with those of the PP/PA6 mechanical blends, and the amount of gPP and the content of the third monomer during the preparation of gPP affected the mechanical properties of the compatibilized blends. Scanning electron microscopy and transmission electron microscopy indicated that the particle sizes of the dispersed phases of the compatibilized PP/PA6 blends became smaller and that the interfaces became more indistinct in comparison with the mechanical blends. The microcrystal size of PA6 and the crystallinity of the two components of the PP/PA6 blends decreased after compatibilization with gPP. The compatibilized PP/PA6 blends possessed higher pseudoplasticity, melt viscosity, and flow activation energy. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 420–427, 2004     

Preparation and properties of dynamically cured PP/MAH‐g‐EVA/epoxy blends

A method concerning with the simultaneous reinforcing and toughening of polypropylene (PP) was reported. Dynamical cure of the epoxy resin with 2‐ethylene‐4‐methane‐imidazole (EMI‐2,4) was successfully applied in the PP/maleic anhydride‐grafted ethylene‐vinyl acetate copolymer (MAH‐g‐EVA), and the obtained blends named as dynamically cured PP/MAH‐g‐EVA/epoxy blends. The stiffness and toughness of the blends are in a good balance, and the smaller size of epoxy particle in the PP/MAH‐g‐EVA/epoxy blends shows that MAH‐g‐EVA was also used as a compatibilizer. The structure of the dynamically cured PP/MAH‐g‐EVA/epoxy blends is the embedding of the epoxy particles by the MAH‐g‐EVA. The cured epoxy particles as organic filler increases the stiffness of the PP/MAH‐g‐EVA blends, and the improvement in the toughness is attributed to the embedded structure. The tensile strength and flexural modulus of the blends increase with increasing the epoxy resin content, and the impact strength reaches a maximum of 258 J/m at the epoxy resin content of 10 wt %. DSC analysis shows that the epoxy particles in the dynamically cured PP/MAH‐g‐EVA/epoxy blends could have contained embedded MAH‐g‐EVA, decreasing the nucleating effect of the epoxy resin. Thermogravimetric results show the addition of epoxy resin could improve the thermal stability of PP, the dynamically cured PP/MAH‐g‐EVA/epoxy stability compared with the pure PP. Wide‐angle x‐ray diffraction analysis shows that the dynamical cure and compatibilization do not disturb the crystalline structure of PP in the blends. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Maleic anhydride grafted thermoplastic elastomer as an interfacial modifier for polypropylene/polyamide 6 blends

A maleic anhydride grafted thermoplastic elastomer (TPE_g) was prepared. The effect of the TPE_g on the morphology and performance of polypropylene (PP)/polyamide 6 (PA‐6) blends was studied. The final properties of the blends were tuned through variations in the TPE_g/PA‐6 ratios and TPE_g and PA‐6 percentages in the blends. Scanning electron micrographs showed that the TPE_g greatly improved the homogeneity of the blends, and this led to better mechanical performance. The nonisothermal crystallization behaviors of PP and PA‐6 in the blends, revealed by differential scanning calorimetry, were different from those of pure PP and PA‐6. The crystallization temperature and rate of PP were promoted by the PA‐6 component because of its nucleating effect, whereas stepwise crystallization was detected for PA‐6 in the PP/PA‐6 blends when the TPE_g was added. On the basis of these observations, a schematic model was proposed for these blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1806–1815, 2004     

Electrical properties and morphology of polypropylene/epoxy/glass fiber composites filled with carbon black

The volume resistivity and percolation thresholds of carbon black (CB) filled polypropylene (PP), PP/epoxy, and PP/epoxy/glass fiber (GF) composites were measured. The morphology of these conductive polymer composites was studied with scanning electron microscopy (SEM). The effects of the GF and epoxy contents on the volume resistivity were also investigated. The PP/epoxy/GF/CB composite exhibited a reduced percolation threshold, in comparison with that of the PP/CB and PP/epoxy/CB composites. At a given CB content, the PP/epoxy/GF/CB composite had a lower volume resistivity than the PP/CB and PP/epoxy/CB composites. SEM micrographs showed that CB aggregates formed chainlike structures and dispersed homogeneously within the PP matrix. The addition of the epoxy resin to PP resulted in the preferential location of CB in epoxy, whereas in the PP/epoxy/GF multiphase blends, because of the good affinity of CB to epoxy and of epoxy to GF, CB particles were located in the epoxy phase coated on GF. The decreased percolation threshold and volume resistivity indicated that conductive paths existed in the PP/epoxy/GF/CB composite. The conductive paths were probably formed through the interconnection of GF. Appropriate amounts of GF and epoxy should be used to decrease the volume resistivity and provide sufficient epoxy coating. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1142–1149, 2005     

Mechanical properties of Mg(OH)2/polypropylene composites modified by functionalized polypropylene

Modified Mg(OH)₂/polypropylene (PP) composites were prepared by the addition of functionalized polypropylene (FPP); and acrylic acid (AA) and by the formation of in situ FPP. The effects of the addition of FPP and AA and the formation of in situ FPP on the mechanical properties of Mg(OH)₂/PP composites were investigated. Experimental results indicated that the addition of Mg(OH)₂ markedly reduced the mechanical properties of PP. The extent of reduction in notch impact strength of PP was higher than that in flexural strength and tensile strength. However, tensile modulus and flexural modulus increased with increased Mg(OH)₂ content. The addition of FPP facilitated the improvement in the flexural strength and tensile strength of Mg(OH)₂/PP composites. The higher the Mg(OH)₂ content was, the more significant the effect of FPP was. The incorporation of AA resulted in further increased mechanical properties, in particular the flexural strength, tensile strength, and notch impact strength of Mg(OH)₂/PP composites containing high levels of Mg(OH)₂. It not only improved mechanical properties but also increased the flame retardance of Mg(OH)₂/PP composites. Although the mechanical properties of composites modified by the formation of in situ FPP were lower than those of composites modified by only the addition of AA in the absence of diamylperoxide, the mechanical properties did not decline with increased Mg(OH)₂ content. Moreover, the mechanical properties increased with increasing AA content. The addition of an oxidation resistant did not influence the mechanical properties of the modified Mg(OH)₂/PP composites. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2139–2147, 2003     

Thermal behavior and morphological and rheological properties of polypropylene and novel elastomeric ethylene copolymer blends

The thermal behavior including melting and crystallization behavior and morphological and rheological properties of the blends based on an isotactic polypropylene and a novel maleated elastomeric ethylene copolymer were investigated in this work. The addition of an elastomer to polypropylene (PP) was found not to change the PP crystalline structure significantly when cooled quickly from the melt. On recrystallization at a lower cooling rate, the elastomer promotes the formation of β?pseudohexagonal PP in PP‐rich blends. In elastomer‐rich compositions, heterogeneous nucleation is hindered and homogeneous nucleation takes place. These phenomena are revealed by morphology observation: that, with increasing of the elastomer content, the system undergoes PP continuous, dual‐phase continuity and PP‐dispersed morphologies. The blend viscosity at a low shear rate range increases continuously with increasing elastomer content and shows positive deviations from the additivity rule. In the terminal zone, the dynamic storage modulus of the blends shows positive deviation from the simple mixing rule and the maximum deviation lies in the composition range of dual‐phase continuity which could be caused by a large increase in the interfacial tension. The Cox–Merz rule does not hold for the blends because of the two‐phase heterogeneous structure and its variation in steady and oscillatory shear flow. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3430–3439, 2002     

Miscibility and crystallization of metallocene polyethylene blends with polypropylene

The crystallization and morphology of very‐low‐density polyethylene (VLDPE) and ultra‐low‐density polyethylene (ULDPE) blends with isotactic polypropylene (PP) were studied by differential scanning calorimetry (DSC) and hot‐stage optical microscopy (HSOM) with polarized light. In particular, the isothermal crystallization of PP in molten PE was investigated. A polypropylene homopolymer was melt‐blended with six types of VLDPEs and ULDPEs, with variations in branch content and length and in molecular weight. All the blends contained 20% PP by mass. It was found that the crystallization temperatures of PP and PE changed in the blends, and the crystallization of PP was affected by branch length and content and by the molecular weight of the PE, indicating a certain degree of miscibility between PP and PE. The isothermal crystallization rate of PP decreased in the blends; in particular, the crystallization rate of PP was slower in the ULDPE with lower MFI, suggesting that crystallization of PP was hindered by PE and that its rate was regulated by the viscosity of ULDPE. HSOM images showed that a portion of the PP crystallized from molten PE, although phase separation was obvious, providing additional information on the miscible behavior between PP and VLDPEs (or ULDPEs). Furthermore, the miscible level between the PP and the ULDPEs was higher than that between the PP and the VLDPEs because the degree of change in the crystallization behavior of the PP and PE was greater in the PP–ULDPE blends. This was possibly a result of the higher branch content in the ULDPE. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1179–1189, 2003     

Novel multimonomer‐grafted polypropylene preparation and application in polypropylene/poly(vinyl chloride) blends

A novel grafted polymer was prepared in one step through free‐radical melt grafting in a single‐screw extruder. It was shown that the addition of styrene (St) to the melt‐grafting system as a comonomer could significantly enhance the grafting degree of methyl methacrylate (MMA) onto polypropylene (PP) and reduce the degradation of the PP matrix by means of Fourier transform infrared and melt flow rate testing, respectively. Then, the potential of using multimonomer‐grafted PP, which was designated PP‐g‐(St‐co‐MMA), as the compatibilizer in PP/poly(vinyl chloride) (PVC) blends was also examined. In comparison with PP/PVC blends, the average size of the dispersed phase was greatly reduced in grafted polypropylene (gPP)/PVC blends because of the addition of the PP‐g‐(St‐co‐MMA) graft copolymer. The tensile strength of the gPP/PVC blends increased significantly, and the impact strength was unchanged from that of the pure PP/PVC blends. The results of differential scanning calorimetry and scanning electron microscopy suggested that the compatibility of the PP/PVC blends was improved. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Isothermal crystallization kinetics and morphology development of isotactic polypropylene blends with atactic polypropylene

The crystallization kinetics and morphology development of pure isotactic polypropylene (iPP) homopolymer and iPP blended with atactic polypropylene (aPP) at different aPP contents and the isothermal crystallization temperatures were studied with differential scanning calorimetry, wide‐angle X‐ray diffraction, and polarized optical microscopy. The spherulitic morphologies of pure iPP and larger amounts of aPP for iPP blends showed the negative spherulite, whereas that of smaller amounts of aPP for the iPP blends showed a combination of positive and negative spherulites. This indicated that the morphology transition of the spherulite may have been due to changes the crystal forms of iPP in the iPP blends during crystallization. Therefore, with smaller amounts of aPP, the spherulitic density and overall crystallinity of the iPP blends increased with increasing aPP and presented a lower degree of perfection of the γ form coexisting with the α form of iPP during crystallization. However, with larger amounts of aPP, the spherulitic density and overall crystallinity of the iPP blends decreased and reduced the γ‐form crystals with increasing aPP. These results indicate that the aPP molecules hindered the nucleation rate and promoted the molecular motion and growth rate of iPP with smaller amounts of aPP and hindered both the nucleation rate and growth rate of iPP with larger amounts of aPP during isothermal crystallization. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1093–1104, 2007     

Effect of dynamic shear on the microcellular foaming of polypropylene/high‐density polyethylene blends

Dynamic shear in the axial direction of a rotor was vertically superposed on the melt flow direction, and its effects on the shear rate and melt strength were investigated theoretically. Polypropylene/high‐density polyethylene blends were microcellularly foamed with different vibration parameters. The experimental results were compared with those of a theoretical analysis, and the effects of dynamic shear on the foamability and ultimate cell structure were analyzed in detail. The theoretical results showed that the shear rate and melt strength increased with an increase in the vibration amplitude and frequency. The enhanced melt strength could effectively restrict cell growth, prevent cell rupture, and improve foamability. The experimental results showed that the cell orientation decreased and the cell structure was improved when axial dynamic shear induced by rotor vibrations was superposed on the melt flow direction. Furthermore, the cell diameter decreased and the cell density increased with increases in the vibration amplitude and frequency. The experimental results were very consistent with the theoretical analysis. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization and dynamic mechanical properties of polypropylene/polystyrene blends modified with maleic anhydride and styrene

Polypropylene (PP)/polystyrene (PS) blends modified with reactive monomers, such as maleic anhydride (MAH) and styrene (St), and in situ formed PP/PS blends were prepared by melting extrusion. The crystallization and melting behavior and the dynamic mechanical properties of the PP/PS blends, including the structure of the grafted copolymer, were investigated with differential scanning calorimetry, dynamic mechanical analysis, and Fourier transform infrared. The results indicated that the addition of MAH hardly influenced the crystallization temperature of PP in the blends, but the addition of MAH and St increased the crystallization temperature of PP in its blends. The blends showed no remarkable variety for the melting temperature, but the shapes of the melting peaks were influenced by the addition of the reactive monomers. In addition, a significant increase in the storage and loss moduli of all the modified PP/PS blends was observed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2038–2045, 2005     

Nonisothermal crystallization,melting behavior,and morphology of polypropylene/metallocene‐catalyzed polyethylene blends

The nonisothermal crystallization, melting behavior, and morphology of blends of polypropylene (PP) and a metallocene‐catalyzed polyethylene (mPE) elastomer were studied with differential scanning calorimetry, scanning electron microscopy, polarized optical microscopy, and X‐ray diffraction. The results showed that PP and mPE were partially miscible and could form some cocrystallization, although the extent was very small. A modified Avrami analysis and the Mo method were used to analyze the nonisothermal crystallization kinetics of the blends. The values of the Avrami exponent indicated that the crystallization nucleation of the blends was homogeneous, the growth of the spherulites was three‐dimensional, and the crystallization mechanism of PP was not affected by mPE. The crystallization activation energy was estimated with the Kissinger method. Interesting results were obtained with the modified Avrami analysis and Mo and Kissinger methods, and the conclusions were in good agreement. The addition of less mPE increased the overall crystallization rate of PP. The relationship between the composition and morphology of the blends was examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1203–1210, 2004     

Properties of dynamically vulcanized ethylene–propylene–diene copolymer/polypropylene blends

In this study, vulcanized thermoplastic elastomers were produced through the formation of crosslinks with peroxide for different ratios of ethylene–propylene–diene copolymer to polypropylene. Mixing was performed with a twin‐screw extruder. Afterward, the yield, tensile strength, elastic modulus, elongation, Izod impact strength, hardness, melt flow index, Vicat softening point, heat deflection temperature, and density of the crosslinks were determined. The thermal transition temperatures and microstructure were determined with differential scanning calorimetry and scanning electron microscopy, respectively. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3895–3902, 2007     

Fracture morphology of Mg(OH)2/polypropylene composites modified by functionalized polypropylene

The morphologies of the fracture surface under impact and flexural testing of Mg(OH)₂/Polypropylene (PP) composites and their modified composites were investigated by scanning electron microscopy. Experimental results indicated that addition of functionalized polypropylene (FPP) and acrylic acid (AA) and the formation of in situ FPP changed the fracture morphologies of Mg(OH)₂/PP composites. We believe that addition of these modifiers improved the interfacial interaction and enhanced the interface adhesion between the particle and the matrix in Mg(OH)₂/PP composites. The degree of improvement was more significant in Mg(OH)₂/PP composites modified by the formation of in situ FPP. At low Mg(OH)₂ content, 2 phr AA exhibited a marked effect, but at high Mg(OH)₂ content, 4 phr AA afforded good effect. Due to the improved interface adhesion by interface interactions the fracture mechanism transformed from interface debonded fracture into a matrix fracture. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2148–2159, 2003     

Effect of talc on the properties of polypropylene/ethylene/propylene/diene terpolymer blends

In the present study, the effect of talc content on the mechanical, thermal, and microstructural properties of the isotactic polypropylene (i‐PP) and elastomeric ethylene/propylene/diene terpolymer (EPDM) blends were investigated. In the experimental study, five different talc concentrations, 3, 6, 9, 12, and 15 wt %, were added to i‐PP/EPDM (88/12) blends to produce ternary composites. The mechanical properties such as yield and tensile strengths, elongation at break, elasticity modulus, izod impact strength for notch tip radius of 1 mm, and hardness with and without heat treatments and thermal properties, such as melt flow index (MFI), of the ternary composites have been investigated. The annealing heat treatment was carried out at 100°C for holding time of 75 h. From the tensile test results, an increased trend for the yield and tensile strengths and elasticity modulus was seen for lower talc contents, while elongation at break showed a sharp decrease with the addition of talc. In the case of MFI, talc addition decreased the MFI of i‐PP/EPDM blends. It was concluded that, taking into consideration, mechanical properties and annealing heat treatment, heat treatment has much more effect on higher yield and tensile strengths, elongation at break, elasticity modulus, impact strength, and hardness. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3033–3039, 2006