Impact of graphene oxide nanoparticles and carbon black on the gamma radiation sensitization of acrylonitrile–butadiene rubber seal materials

Seals prepared from acrylonitrile–butadiene rubber (NBR) are primarily used in nuclear services. Nevertheless, at relatively high ionizing radiation doses, NBR seal materials may undergo radiation-induced degradation processes, leading to adverse effects on the sealing ability life. Herein, to strengthen the functional characteristics of NBR seals against radiation, graphene oxide (GO) nanoparticles were prepared and characterized by transmission electron microscopy, X-ray diffraction (XRD), Fourier transform infrared (FTIR), and ultraviolet/visible spectroscopies. Various NBR/GO composites fabricated with different ratios of GO nanoparticles and in the presence or absence of carbon black (CB) were investigated via cross-linking density, scanning electron microscopy, XRD, FTIR, and mechanical and thermal stability analyses. The synergistic effect of the simultaneous presence of GO and CB on the NBR seal sensitization to gamma radiation up to a dose of 1 MGy was studied. The physicomechanical properties were enhanced by adding GO nanosheets up to 3 phr and by incorporating 35 phr of a CB with GO until 5 phr. Further, the application of γ-irradiation resulted in an overall enhancement in the mechanical, physical, and thermal stability of the prepared composites up to 0.5 and 1 MGy with GO nanosheets in the absence or presence of CB particles, respectively. The mechanical measurements indicated significant increments by loading with GO nanosheets in the absence and presence of CB as well as by irradiation. The tensile strength elevated up to about 121%, 336%, and 366% by adding 3 phr GO, 3 GO:35 CB phr, and 5 GO:35 CB phr, respectively.     

Thermal decomposition kinetics of dynamically vulcanized polyamide 6–acrylonitrile butadiene rubber–halloysite nanotube nanocomposites

Thermally stable thermoplastic elastomer nanocomposites based on polyamide 6 (PA6), acrylonitrile butadiene rubber (NBR), and halloysite nanotubes (HNTs) were dynamically vulcanized, and their nonisothermal decomposition kinetics were examined. The Friedman, Kissinger–Akahira–Sunose (KAS), Ozawa–Wall–Flynn (FWO), and modified Coats–Redfern (m-CR) isoconversional models were used to obtain information about the kinetics of the thermal decomposition of PA6–NBR–HNTs in terms of the activation energy per partial mass loss monitored through thermogravimetric analyses performed at different heating rates. An erratic trend was due to the Friedman model, especially for systems having higher HNT loadings, whereas the KAS, FWO, and m-CR models revealed very similar meaningful thermal decomposition kinetics. A relatively high activation energy corroborating a reliable thermal stability was obtained by the addition of HNTs to PA6–NBR, and the resistance against decomposition was higher for systems containing more HNT. This signified the role of the HNTs as thermal stability modifiers. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47483.     

Effects of modified silica on the co-vulcanization kinetics and mechanical performances of natural rubber/styrene–butadiene rubber blends

Rubber blends are widely used for combining the advantages of each rubber component. However, to date, how to determine and distinguish the vulcanization kinetics for each single rubber phase in rubber blends during the co-vulcanization process is still a challenge. Herein, high-resolution pyrolysis gas chromatography–mass spectrometry (HR PyGC-MS) was employed for the first time to investigate the vulcanization kinetics of natural rubber (NR) and styrene–butadiene rubber (SBR) in NR/SBR blends filled with modified silica (SiO₂). The reaction rates of crosslinking of each rubber phase in NR/SBR were calculated, which showed that the crosslinking rates of NR were much lower than those of SBR phase in the unfilled blends and blends filled with unmodified and silane modified silica. Interestingly, the vulcanization rates of NR and SBR phase were approximately same in the vulcanization accelerator modified silica filled blends, showing better co-vulcanization. In addition, the vulcanization accelerator modified silica was uniformly dispersed and endowed rubber blends with higher mechanical strength compared to the untreated silica. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48838.     

Supercapacitive properties of electrodeposited polypyrrole on acrylonitrile–butadiene rubber as a flexible current collector

Flexible sheets consisting of acrylonitrile–butadiene rubber (NBR) and vapor-grown carbon fiber (VGCF) are newly prepared varying the composition (VGCF 10–30 wt%) for use as a current collector of supercapacitor electrodes. The electrical conductivity of as-prepared VGCF/NBR current collector can be enhanced as the content of VGCF increases. The VGCF/NBR current collector is then electrodeposited with pyrrole using a potentiodynamic cyclic voltammetry to yield a polypyrrole (PPy)/VGCF/NBR composite electrode. Cyclic voltammetry result for the PPy/VGCF/NBR composites shows that the sample with 30 wt% VGCF achieves a maximum specific capacitance (125.8 F g^?1) at 5?mV?s^?1 and reaches a lower specific capacitance at higher scan rates. In addition, the flexibility of supercapacitor electrode of PPy can also be established with a comparable capacitance value by using the NBR-based current collector.     

Studies on the microwave conductivity of polyaniline–polyvinyl chloride composites

Abstract

Polyaniline/polyvinyl chloride semi-interpenetrating polymer networks were prepared by the chemical oxidative polymerisation of aniline using ammonium persulphate as initiator in the presence of emulsion-grade polyvinyl chloride. The polymerisation was carried out for about 4 h at room temperature. It was then dried under different conditions (room temperature drying, vacuum drying and oven drying). The dielectric properties such as dielectric constant, conductivity, dielectric loss, dielectric heating coefficient and loss tangent were measured using the cavity perturbation technique. Cavity operating at S band was used for the study. The dielectric properties were found to depend on both the frequency and the composition of the mix (polyaniline-polyvinyl chloride).     

Analysis and modeling of modified styrene–acrylonitrile/carboxylated acrylonitrile butadiene rubber nanocomposites filled with graphene and graphene oxide: Interfacial interaction and nonlinear elastoplastic behavior

Nonlinear elastoplastic behavior of the nanocomposites based on the styrene–acrylonitrile/carboxylated acrylonitrile butadiene rubber (SAN/XNBR) blend was investigated using experimental and theoretical analysis. Graphene, graphene oxide nanoparticles, and glycidyl methacrylate-grafted-XNBR (XNBR-g-GMA) as a compatibilizer were incorporated in the SAN/XNBR blends. In this regard, the focus of this study is on modeling of the stress–strain behavior of these nanocomposites, considering the effect of the interfacial interactions made by compatibilizer. For this purpose, field emission scanning electron microscopy (FESEM) and transmission electron microscope (TEM) techniques were used to investigate the relationship between microstructure and mechanical properties of nanocomposites. In addition, FESEM and TEM images showed that the presence of a compatibilizer could influence the dispersion and localization of the nanoparticles. According to the tensile test results, the presence of the compatibilizer increased the mechanical properties of the nanocomposites, specifically elongation at break. Considering the nanocomposite containing compatibilizer and graphene oxide, the elongation at break increased about 570% compared with the nanocomposite without compatibilizer. Better dispersion of graphene oxide and the creation of chemical interaction among components in the presence of the XNBR-g-GMA compatibilizer could be the reasons for these improvements, as confirmed by TEM. The usage of the Bergstrom–Boyce model for analyzing the nonlinear elastoplastic behavior of the nanocomposites illustrated proper conformity with the experimental data in the elastic region. However, there are some deviations in the viscoplastic region, particularly close to the breaking elongation region.     

Thermorheological studies of novel thermoplastic elastomeric blends of nitrile rubber (NBR) and scrap computer plastics (SCP) based on acrylonitrile–butadiene–styrene terpolymer (ABS)

Abstract

Thermorheological properties of thermoplastic elastomeric 60/40, 70/30 and 80/20 nitrile rubber (NBR)/scrap computer plastics (SCP) blends were studied by using parallel plate rheometer. The blends exhibit pseudoplasticity and obey power law model. The dynamically vulcanised blends have higher dynamic viscosities than their unvulcanised counterparts. Surface finish and die swell of the extrudates are improved upon dynamic vulcanisation. The thermoplastic elastomeric blends of NBR/SCP exhibit 'thermorheological complexity'.     

Impact of the aluminum sulfate 18-hydrate particle size on the coordination crosslinking behaviors of acrylonitrile–butadiene rubber–aluminum sulfate 18-hydrate composites

In this study, aluminum sulfate 18-hydrate [Al₂(SO₄)₃·18H₂O] particles of different sizes, which were obtained via high-energy ball-milling technology, were successfully compounded with acrylonitrile–butadiene rubber (NBR) to fabricate crosslinked rubber composites. The results suggest that high-energy ball milling had no significant change on the crystal structure of Al₂(SO₄)₃·18H₂O, but it significantly reduced the particle size. The effects of the particles size on the coordination crosslinking behaviors and mechanical properties of the NBR–Al₂(SO₄)₃·18H₂O composites were fully explored. The coordination crosslinking reaction was demonstrated to occur between the nitrile group (─CN) and Al(III). Moreover, with the decreasing particle size, the composites achieved a better interfacial adhesion and more crosslinking points, and this led to significant increases in the crosslinking density and the mechanical properties. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47717.     

An update on the mechanism of the graphene–NO reaction

Cognizant of the key experimental facts from studies of carbonaceous solids ranging from soot to graphite, we performed a quantum chemistry study of the interaction of NO monomer or dimer with one or more zigzag sites. Thermodynamic and kinetic results were used to examine two alternative mechanisms proposed in the literature, and to compare them with the graphene–O₂ reaction mechanism. The chemisorption stoichiometry similarities are striking; but the differences, especially regarding the intermediate role of N₂O, have important practical implications. Monomer chemisorption on an isolated site is a dead-end and temporarily inhibiting process, similar to that of formation of a stable C–O surface complex in the graphene–O₂ reaction. When two sites are available, successive monomer adsorption eventually leads to N₂O formation subsequent to parallel reorientation of the first NO molecule. If three contiguous sites are available, N₂ and CO are the principal products. Chemisorption of the dimer provides a straightforward path to N₂ and CO₂ when one site is available and to N₂ and CO when two sites are available. The formation of N₂O is also feasible in this case, both during adsorption and desorption; in the adsorption phase it is very sensitive to the details of the electron pairing processes.     

The structure and dynamic properties of nitrile–butadiene rubber/poly(vinyl chloride)/hindered phenol crosslinked composites

In this article, a new nitrile–butadiene rubber (NBR) crosslinked composites containing poly(viny chloride) (PVC) and hindered phenol (AO-80 and AO-60) was successfully prepared by melt-blending procedure. Microstruture and dynamic mechanical properties of the composites were investigated using SEM, DSC, XRD, and DMTA. Most of hindered phenol was dissolved in the NBR/PVC matrix and formed a much fine dispersion. The results of DSC and DMTA showed that strong intermolecular interaction was formed between the hindered phenol and NBR/PVC matrix. The NBR/PVC/AO-80 crosslinked composites showed only one transition with higher glass transition temperature and higher tan δ value than the neat matrix, whereas for the NBR/PVC/AO-60 crosslinked composites, a new transition appeared above the glass transition temperature of matrix, which was associated with the intermolecular interaction between AO-60 and PVC component of the matrix. Both AO-80 and AO-60 in the crosslinked composites existed in amorphous form. Furthermore, the chemical crosslinking of composites resulted in better properties of the materials, e.g., considerable tensile strength and applied elastic reversion. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Voltammetric determination of alkannin using an Au nanoparticles–poly(diallyldimethylammonium chloride)-functionalized graphene nanocomposite film

An electrochemical sensor based on Au nanoparticles (AuNPs)–poly(diallyldimethylammonium chloride) (PDDA)-functionalized graphene (AuNPs–PDDA-G) nanocomposite was fabricated for the sensitive detection of alkannin. The nanocomposite was characterized by X-ray diffraction, ultraviolet/visible spectra, scanning electron microscopy, and transmission electron microscopy. Cyclic voltammetry and differential pulse voltammetry were used to investigate the electrochemical behaviors of alkannin on the AuNPs–PDDA-G nanocomposite film-modified glassy carbon electrode. This electrochemical sensor displayed satisfactory analytical performance for alkannin detection over a range from 5.0 nmol L^?1 to 3.0 μmol L^?1 with a detection limit of 1.4 nmol L^?1 (S/N = 3). Moreover, the sensor also exhibited good reproducibility and stability, and could be used for the detection of alkannin in real samples with satisfactory results.     

Exploiting the Plackett–Burman design to examine the formulation effect on curing characteristics of oil palm ash-filled acrylonitrile butadiene rubber compounds

The present paper is focused on exploiting Plackett–Burman design to examine the formulation effect of various chemical components content on the curing characteristics of oil palm ash (OPA)-filled acrylonitrile butadiene rubber (NBR) compound. The filled-NBR compound was prepared by conventional laboratory-sized two roll mill and cured using sulfuric system. Six independent variables such as content of zinc oxide, stearic acid, N-isopropyl-N′-phenyl-p-phenylenediamine, N-cyclohexyl-2-benzothiazole sulfenamide (CBS), sulfur, and even OPA filler were carried out to screen their significant effect on the curing characteristics of NBR compound. The scorch time, optimal cure time, minimum torque, and maximum torque were selected as a response. Results showed that the scorch time and the optimal cure time were significantly affected by CBS, whereas the minimum torque and maximum torque were significantly affected by OPA and sulfur, respectively, within the studied range. Among the chemical components under study, zinc oxide and stearic acid had the least effect on the curing properties of NBR compound. Analysis of variances for all factorial models demonstrated that the model was significant with P value <0.05 while the regularity (R ²) of all models was greater than 0.9. Lastly, the optimal chemical concentrations were predicted to acquire the optimal condition of the curing system for filled-NBR compound.     

Effect of silica reinforcement on natural rubber and butadiene rubber vulcanizates by a sol–gel reaction with tetraethoxysilane

The effect of silica reinforcement was studied for natural rubber (NR) and butadiene rubber (BR) vulcanizates by a sol–gel reaction with tetraethoxysilane at different temperatures. The formation of silica in the rubber vulcanizates was investigated analytically with Fourier transform infrared spectroscopy and energy-dispersive X-ray analysis. The variations of the mechanical and dynamic properties were measured in the NR and BR vulcanizates with silica filling. The hardness of the rubber vulcanizates increased with silica filling in the rubber matrix. The tensile strength and elongation at break decreased with silica filling in the NR vulcanizates. The moduli at 50, 100, and 300% elongation increased with silica filling in the rubber matrix. The storage modulus of silica-filled rubber vulcanizates became higher than that of pure rubber vulcanizates. The temperature dependence of the loss modulus also increased with silica filling. The temperature dependence of the loss tangent was maintained, regardless of silica filling in the BR vulcanizates. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Melting and crystallization behaviors of compatibilized poly(trimethylene terephthalate)/acrylonitrile–butadiene–styrene blends

The melting and crystallization behaviors of poly(trimethylene terephthalate) (PTT)/acrylonitrile–butadiene–styrene (ABS) blends were investigated with and without epoxy or styrene–butadiene–maleic anhydride copolymer (SBM) as a reactive compatibilizer. The existence of two separate composition-dependent glass-transition temperatures (T_g's) indicated that PTT was partially miscible with ABS over the entire composition range. The melting temperature of the PTT phase in the blends was also composition dependent and shifted to lower temperatures with increasing ABS content. Both the cold crystallization temperature and T_g of the PTT phase moved to higher temperatures in the presence of compatibilizers, which indicated their compatibilization effects on the blends. A crystallization exotherm of the PTT phase was noticed for all of the PTT/ABS blends. The crystallization behaviors were completely different at low and high ABS contents. When ABS was 0–50 wt %, the crystallization process of PTT shifted slightly to higher temperatures as the ABS content was increased. When ABS was 60 wt % or greater, PTT showed fractionated crystallization. The effects of both the epoxy and SBM compatibilizers on the crystallization of PTT were content dependent. At a lower contents of 1–3 wt % epoxy or 1 wt % SBM, the crystallization was retarded, whereas at a higher content of 5 wt %, the crystallization was accelerated. The crystallization kinetics were analyzed with a modified Avrami equation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of hydrogen functionalization on the fracture strength of graphene and the interfacial properties of graphene–polymer nanocomposite

Using molecular dynamics and classical continuum concepts, we investigated the effects of hydrogen functionalization on the fracture strength of graphene and also on the interfacial properties of graphene–polymer nanocomposite. Moreover, we developed an atomistic model to assess the temperature and strain rate dependent fracture strength of functionalized graphene along various chiral directions. Results indicate that hydrogen functionalization at elevated temperatures highly degrade the fracture strength of graphene. The functionalization also deteriorates the interfacial strength of graphene–polymer nanocomposite. Near-crack-tip stress distribution depicted by continuum mechanics can be successfully used to investigate the impact of hydrogen passivation of dangling carbon bonds on the strength of graphene. We further derived a continuum-based model to characterize the non-bonded interaction of graphene–polymer nanocomposite. These results indicate that classical continuum concepts are accurate even at a scale of several nanometers. Our work provides a remarkable insight into the fracture strength of graphene and graphene–polymer nanocomposites, which are critical in designing experimental and instrumental applications.     

Study of the phase morphology and toughness in poly (vinyl chloride)/acrylonitrile–styrene-acrylic/styrene–butadiene–styrene ternary blends influenced by interfacial/surface tension

The effect of interfacial interaction on the phase morphology and toughness of poly (vinyl chloride) (PVC)/acrylonitrile–styrene-acrylic (ASA) terpolymer/styrene–butadiene–styrene (SBS) block copolymer ternary blends has been investigated. Water and diiodomethane liquids were used for static contact angle measurements to get surface tension and calculate interfacial tension. A dispersed phase morphology of ASA and SBS in the PVC matrix was predicted by the spreading coefficient theory, which was calculated through interfacial tensions between different polymer pairs. Extraction experiment and scanning electron microscopy were combined to verify this morphology. When the volume fraction of SBS was small, SBS was dispersed in the matrix as droplets and the strong PVC/styrene–acrylonitrile interfacial interaction made up for the poor interfacial adhesion between SBS and PVC. Herein, SBS showed an effective toughening effect on PVC/ASA blends. With the addition of 2.5- and 5-phr SBS, the blends had the highest impact strength of 88.75 kJ/m² at 23 °C and 9.98 kJ/m² at 0 °C, respectively. With the further increase of the SBS content, the diameter of the SBS drops increased largely and the poor interfacial adhesion between SBS and PVC played a leading role, resulting in a sharp decrease in toughness and a sharp ductile–brittle transition. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47721.     

Application of hygrothermally decomposed polyurethane in rubber recipes Part 2–Influence of hygrothermally decomposed polyester–urethane on cure characteristics and viscoelastic behaviour of styrene/butadiene rubber

Abstract

Hygrothermally decomposed polyester–urethane (HD PUR) was mixed at concentrations up to 20 pphr with a styrene/butadiene rubber (SBR), using an efficient vulcanisation system. Changes in the cure behaviour were followed by vulcametry, plate–plate rheometry, and differential scanning calorimetry. It was found that the degree of crosslinking was increased by the incorporation of HD PUR, which acts as an accelerator in SBR stocks. Increasing crosslinking resulted in higher stiffness and strength and was accompanied by a reduction in elongation at break and swelling index.     

Effect of the sheet size on the thermal stability of silicone rubber–reduced graphene oxide nanocomposites

The structures of differently sized reduced graphene oxides (rGOs), the dispersion state, and the compatibility of rGO with silicone rubber (SR) are important impact factors on the properties of SR–rGO nanocomposites. To analyze the influence of the size of rGO on the properties of SR-based nanocomposites, three differently sized rGO sheets were introduced into SR to fabricate a series of SR-based nanocomposites. The SR–middle-sized reduced graphene oxide (MrGO) nanocomposites showed the best mechanical and thermal properties. Compared with the blank sample, the SR–MrGO nanocomposites presented remarkable two-fold and three-fold increases in the tensile modulus and strength values. The initial degradation temperature increased nearly 40 °C. In this study, we investigated the size effect of graphene on the thermal stability by examining the thermal degradation mechanism of the different SR–rGO nanocomposites in detail. Ultimately, this research may suggest a facile approach for improving the thermal stability of SR. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47034.     

Correlation of the morphology and thermooxidative degradation behavior of poly(ethylene terephthalate)–nitrile butadiene rubber–polycarbonate ternary blends

In this study, we prepared ternary poly(ethylene terephthalate) (PET)–nitrile butadiene rubber (NBR)–polycarbonate (PC) blends through a molten mixing procedure, and with a corotating extruder, we studied the morphology and thermodynamic properties of each purified polymer and the binary and ternary blends with different compositions. Dynamic mechanical analysis of both the PET–PC and PET–NBR samples showed individual loss peaks for each component, but in different ternary samples, the effects of different percentages of components (PC–PC and PET–NBR) were observed; this revealed changes in the loss peak locations. Individual loss peaks of PET and PC in the ternary PET–NBR–PC blends (81/9/10 and 63/30/7)—proof of the miscibility of the samples—were also observed in this study. The thermal properties of the samples were measured and examined with the thermogravimetric analysis and differential thermogravimetry testing methods. The activation energy and order of reaction values for the samples under an air atmosphere with single-rate methods of heating were studied. Finally, the relation between the type of morphology and the thermal degradation behavior was investigated. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47171.     

The effect of Sn content on the electrocatalytic properties of Pt–Sn nanoparticles dispersed on graphene nanosheets for the methanol oxidation reaction

Direct methanol fuel cell (DMFC) electrode catalysts with improved electrochemical properties have been prepared by dispersing platinum–tin (Pt–Sn) nanoparticles onto graphene sheets. During the deposition, a majority of the oxygenated functional groups on the graphene oxide nanosheets were removed, resulting in the formation of graphene. Microstructural characterization shows that metallic Pt, Pt–Sn alloy and tin dioxide (SnO₂) nanoparticles were distributed on the graphene sheets, representing different lattice planes during the synthetic process. In terms of the electrocatalytic properties, graphene-supported Pt–Sn and graphene-supported Pt catalysts exhibited much higher current densities compared with that of commercial carbon black-supported Pt catalysts. Graphene-supported Pt–Sn increased the electrocatalytic activity, which is strongly influenced by the addition of Sn in its alloyed and oxidized forms, boosting the reaction more readily because of the lower oxidation potential.