Studies on polyblends of poly(vinyl chloride) and acrylonitrile-butadiene-styrene terpolymer

Blends of poly (vinyl chloride) (PVC) and acrylonitrile-butadiene styrene (ABS) terpolymer were prepared in different ratios by a melt blending technique. ABS containing three different levels of rubber content were used. A quantitative assessment of ABS in PVC/ABS blends has been shown by infrared studies. ABS content has been shown as the presence of the characteristic acrylonitrile peak. Differential scanning calorimetry (DSC) studies have been carried out to study the glass transition (T_g) behavior of the blends. Two T_g values corresponding to PVC and styrene-acrylonitrile (SAN) copolymer have been observed. Thermogravimetric analysis (TGA) reveals a significant improvement in thermal stability of these blends as compared to PVC. Mechanical properties show a significant increase in the impact strength which is related to rubber content of the ABS used. Morphological studies have been carried out by scanning electron microscopy which support the observation that an increase in rubber content results in greater ductility.     

Morphological,mechanical, and rheological studies of PVC/ABS blends in the presence of maleic anhydride

A novel method of enhancing compatibility in PVC/ABS blends is the use of ABS‐grafted‐(maleic anhydride) (ABS‐g‐MAH) as a compatibilizer. In this study, maleic anhydride was grafted onto ABS (initiated by peroxide) in an internal mixer. Grafting degree was determined by a back‐titration method, and certain amounts of the resultant ABS‐g‐MAH were added to PVC/ABS blends during their melt blending in the mixer. The weight ratio of PVC to ABS was kept at 70:30. Evaluation of compatibilization was accomplished via tensile and notched Izod impact tests, scanning electron microscopy (SEM), and rheological studies. According to the SEM micrographs, better dispersion of the rubber phase and its finer size in properly compatibilized blends were indications of better compatibility. Besides, in the presence of a proper amount [5 parts per hundred parts of PVC (php)] of ABS‐g‐MAH, PVC/ABS blends showed significantly higher impact strengths than uncompatibilized blends. This result, in turn, would be an indication of better compatibility. In the presence of 5 php of compatibilizer, the higher complex viscosity and storage modulus, as well as a lower loss modulus and loss factor in the range of frequency studied, indicated stronger interfacial adhesion as a result of interaction between maleic anhydride and the PVC‐SAN matrix. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Blends of poly(vinyl chloride) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer: Thermal properties,mechanical properties,and morphology

Binary blends of poly(vinyl chloride) (PVC) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer (AMS‐ABS) were prepared via melt blending. A single glass transition temperature (T_g) was observed by differential scanning calorimetry, thus indicating that PVC is miscible with the α‐methylstyrene‐acrylonitrile‐styrene in AMS‐ABS. The results from attenuated total reflection Fourier transform infrared spectra indicated that specific strong interactions were not available in the blends. With increasing amounts of AMS‐ABS, both heat distortion temperature and thermal stability were increased considerably. With regard to mechanical properties, flexural and tensile properties decreased with increasing AMS‐ABS content. A synergism was observed in impact strength. The morphology of both impact‐fractured and tensile‐fractured surfaces, observed by scanning electron microscopy, correlated well with the mechanical properties. It is suggested that there was a transition of fracture mechanisms with the changing composition of the binary blends—from shear yielding for blends rich in PVC to cavitation for blends rich in AMS‐ABS. J. VINYL ADDIT. TECHNOL., 19:1–10, 2013. © 2013 Society of Plastics Engineers     

The experimental results and simulation of temperature dependence of brittle‐ductile transition in PVC/CPE blends and PVC/CPE/nano‐CaCO3 composites

The effect of chlorinated polyethylene (CPE) content and test temperature on the notched Izod impact strength and brittle‐ductile transition behaviors for polyvinylchloride (PVC)/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites is studied. The CPE content and the test temperature regions are from 0–50 phr and 243–363 K, respectively. It is found that the optimum nano‐CaCO₃ content is 15 phr for PVC/CPE/nano‐CaCO₃ ternary composites. For both PVC/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites, the impact strength is improved remarkably when the CPE content or test temperature is higher than the critical value, that is, brittle‐ductile transition content (C_BD) or brittle‐ductile transition temperature (T_BD). The T_BD is closely related to the CPE content, the higher the CPE content, the lower the T_BD. The temperature dependence of impact strength for PVC/CPE blends and PVC/CPE/nano‐CaCO₃ ternary composites can be well simulated with a logistic fitting model, and the simulation results can be illustrated with the percolation model proposed by Wu and Jiang. DMA results reveal that both PVC and CPE can affect the T_BD of PVC/CPE blends and PVC/CPE/nano‐CaCO₃ composites. When the CPE content is enough (20 phr), the CPE is more important than PVC for determining the T_BD of PVC/CPE blends and PVC/CPE/nano‐CaCO₃ composites. Scanning electron microscopy (SEM) observations reveal that the impact fractured mechanism can change from brittle to ductile with increasing test temperature for these PVC systems. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Interfacial structures and mechanical properties of PVC composites reinforced by CaCO3 with different particle sizes and surface treatments

The effects of particle size and surface treatment of CaCO₃ particles on the microstructure and mechanical properties of poly(vinyl chloride) (PVC) composites filled with CaCO₃ particles via a melt blending method were studied by SEM, an AG‐2000 universal material testing machine and an XJU‐2.75 Izod impact strength machine. The tensile and impact strengths of CaCO₃/PVC greatly increased with decreasing CaCO₃ particle size, which was attributed to increased interfacial contact area and enhanced interfacial adhesion between CaCO₃ particles and PVC matrix. Titanate‐treated nano‐CaCO₃/PVC composites had superior tensile and impact strengths to untreated or sodium‐stearate‐treated CaCO₃/PVC composites. The impact strength of titanate‐treated nano‐CaCO₃/PVC composites was 26.3 ± 1.1 kJ m⁻², more than three times that of pure PVC materials. The interfacial adhesion between CaCO₃ particles and PVC matrix was characterized by the interfacial interaction parameter B and the debonding angle θ, both of which were calculated from the tensile strength of CaCO₃/PVC composites. Copyright © 2005 Society of Chemical Industry     

Ultrafine full-vulcanized powdered rubbers/PVC compounds with higher toughness and higher heat resistance

A new type of rigid PVC compound with higher toughness and higher heat resistance was prepared by using a new type of PVC modifier, ultrafine full-vulcanized powdered rubber (UFPR). The UFPRs used in this paper were butadiene nitrile UFPR-1 (NBR-UFPR-1) with particle size of about 150 nm and butadiene nitrile UFPR-2 (NBR-UFPR-2) with particle size of about 90 nm. Dynamic mechanical thermal analysis (DMTA) showed that glass transition temperature (T_g) of PVC in compounds increased from 77.52 °C of neat PVC to 82.37 and 85.67 °C, while the notched impact strengths increased from 3.1 kJ/m² of neat PVC to 5.2, 5.5 kJ/m², respectively. It can be found that both T_g and toughness of PVC have been improved simultaneously, and the smaller the particle size of NBR-UFPRs, the higher the T_g and the impact strength. The property could be attributed to larger interface and more interfacial interaction between NBR-UFPRs and PVC matrix. Transmission electron microscopy (TEM) showed that NBR-UFPRs could be well dispersed in PVC matrix.     

Mechanical,flammability, and thermal properties of polyvinyl chloride‐wood composites with carbide slag

Carbide slag, an industrial waste produced by calcium carbide hydrolysis to prepare C₂H₂ gas, was successfully used as inorganic filler in the production of polyvinyl chloride (PVC)‐wood composites. carbide slag had an average diameter of 8.1 μm which thermally decomposed at about 450°C, and its main component was Ca(OH)₂. Incorporating carbide slag into PVC‐wood composites substantially decreased the flexural, tensile, and impact strength of the composites as a result of the poor interfacial adhesion between carbide slag and PVC matrix, which could be evidently observed from the scanning electron microscopy (SEM) study. To give carbide slag better use, silane coupling agent KH570 were chose to modify carbide slag. The results indicated that adding carbide slag modified by KH570 (MCS) into PVC‐wood composites could significantly improve its notched impact strength and flexural modulus. The thermogravimetric analysis (TGA) data showed that with the addition of MCS, composite had better thermal stability. It also turned out that with the addition of MCS, its smoke suppression property and flammability were enhanced effectively. To ensure sufficient properties of PVC‐wood composites, the optimal adding content of MCS was 20 phr and it leaded to remarkable performance (its flexural modulus was 3.4 GPa, notched impact strength was 3.87 KJ/m², limiting oxygen index value was 41.5% and smoke density ranting was 55.1%), all of which endowed PVC‐wood composites better utilization. All the results indicated that the preparation of PVC‐wood composites with carbide slag could resolve environmental pollution, reuse carbide slag in different fields, and provide a new method for resource utilization of carbide slag. POLYM. COMPOS., 38:2898–2906, 2017. © 2015 Society of Plastics Engineers     

The roles of polyacrylate in poly(vinyl chloride)‐lignin composites

A novel method was adopted to improve the adhesion between lignin particles and poly(vinyl chloride) (PVC) matrix in PVC‐lignin composites. Lignin was treated with a polyacrylate, poly(ethyl acrylate‐co‐acrylic acid), and the composites was prepared with PVC and the treated lignin. The mechanical properties and morphology of the composites were investigated, and the roles of polyacrylate in the composites were discussed. The results show that both the tensile and impact strengths of the composites are improved when both the content of carboxyl in polyacrylate and its dosage are low, and the optimum is: yield strength, 24.17 MPa, higher than that of PVC control (21.88 MPa); breaking strength, 33.59 MPa, close to that of PVC control (35.62 MPa); and impact strength, 8.0 kJ m⁻², 31% higher than that of PVC control (6.1 kJ m⁻²). Microscopic morphology analysis suggests that polyacrylate improved the adhesion between lignin particles and PVC matrix. The roles of polyacrylate are as the following: polyacrylate is combined with lignin by hydrogen bond and ester bond, and most of its chains spread into PVC matrix due to its good compatibility with PVC, thereby lignin particles can be well bound with PVC matrix. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Toughness of ABS/PBT blends: The relationship between composition,morphology, and fracture behavior

A series of acrylonitrile–butadiene–styrene (ABS) copolymer/poly(butylene terephthalate) (PBT)/acrylonitrile‐styrene‐glycidyl methacrylate (ASG) blends with various compositions were prepared and characterized in this study. When the fraction of ABS exceeds a critical value there is a rapid increase in notched impact strength of ABS/PBT blends no matter whether the compatibilizer ASG is present. By combining morphology observation and notched impact results, we found that the ductile‐brittle transition of the blends is closely related to the morphology inversion. The notched impact strength jumps from 15.9 to 33.4 kJ/m² when phase inversion of ABS occurs at its fraction of 58 wt %. Accordingly, a possible toughening mechanism involved in the blends is proposed on the basis of a careful analysis of fracture energy, crack propagation behavior and fracture surface morphology. It is believed that the continuous ABS phase plays the critical role in toughening ABS/PBT blends. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46051.     

Toughening effects of ethylene–vinyl acetate copolymers with different vinyl acetate content and viscosity on nylon 1010 blends

Nylon 1010 blends with ethylene–vinyl acetate copolymer (EVA) and maleated ethylene–vinyl acetate (EVA‐g‐MAH) were prepared through melt blending. The vinyl acetate (VA) content and viscosity of EVA significantly affected the notched impact strength of nylon/EVA/EVA‐g‐MAH (80/15/5) blends. The nylon/EVA/EVA‐g‐MAH blends with high notched impact strength (over 60 kJ/m²) were obtained when the VA content in EVA ranged from 28 to 60 wt%. The effect of VA content on the notched impact strength of blends was related to the glass transition temperature for EVA with high VA content and crystallinity for EVA with low VA content. For nylon blends with EVA with the same VA content, low viscosity of EVA led to high notched impact strength. Fracture morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends showed that blends with ductile fracture behavior usually had large matrix plastic deformation, which was the main energy dissipation mechanism. A relationship between the notched impact strength and the morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends was well correlated by the interparticle distance model. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Thermal and dynamic mechanical behavior of poly(vinyl chloride)/wood flour composites

Thermal and dynamic mechanical behaviors of wood plastic composites made of poly vinyl chloride (PVC) and surface treated, untreated wood flour were characterized by using differential scanning calorimetry and dynamic mechanical analysis. Glass transition temperature (T_g) of PVC was slightly increased by the addition of wood flour and by wood flour surface treatments. Heat capacity differences (ΔC_p) of composites before and after glass transition were markedly reduced. PVC/wood composites exhibited smaller tan δ peaks than PVC alone, suggesting that less energy was dissipated for coordinated movements and disentanglements of PVC polymer chains in the composites. The rubbery plateaus of storage modulus (E′) curves almost disappeared for PVC/wood composites in contrast to a well defined plateau range for pure PVC. It is proposed that wood flour particles act as “physical crosslinking points” or “pinning centers” inside the PVC matrix, resulting in the absence of the rubbery plateau and high E′ above T_g. The mobility of PVC chain segments were further retarded by the presence of surface modified wood flour. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The dynamic mechanical analysis,impact, and morphological studies of EPDM–PVC and MMA‐g‐EPDM–PVC blends

The dynamic mechanical studies, impact resistance, and scanning electron microscopic studies of ethylene propylene diene terpolymer–poly(vinyl chloride) (EPDM–PVC) and methyl methacrylate grafted EPDM rubber (MMA‐g‐EPDM)–PVC (graft contents of 4, 13, 21, and 32%) blends were undertaken. All the regions of viscoelasticity were present in the E′ curve, while the E″ curve showed two glass transition temperatures for EPDM–PVC and MMA‐g‐EPDM–PVC blends, and the T_g increased with increasing graft content, indicating the incompatibility of these blends. The tan δ curve showed three dispersion regions for all blends arising from the α, β, and Γ transitions of the molecules. The sharp α transition peak shifted to higher temperatures with increasing concentration of the graft copolymer in the blends. EPDM showed less improvement while a sixfold increase in impact strength was noticed with the grafted EPDM. The scanning electron microscopy micrographs of EPDM–PVC showed less interaction between the phases in comparison to MMA‐g‐EPDM–PVC blends. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1959–1968, 1999     

Studies on morphology and thermomechanical performance of ABS/PC/organoclay hybrids

In the present research, poly(acrylonitrile‐butadiene‐styrene)/polycarbonate (ABS/PC) blends were prepared in a twin screw extruder. An attempt to reinforce and promote compatibility of the above systems was made by the incorporation of organically modified montmorillonite (OMMT, Cloisite 30B), as well as by the addition of compatibilizer (ABS grafted with maleic anhydride, ABS‐g‐MAH), and the effect of those treatments on the morphology, thermal transitions, rheological, and mechanical properties of the above blends was evaluated. The addition of compatibilizer in ABS/PC blends does not significantly affect the glass transition temperature (T_g) of SAN and PC phases, whereas the incorporation of Cloisite 30B decreases slightly the T_g values of SAN and, more significantly, that of PC in compatibilized and uncompatibilized blends. The T_g of PB phase remains almost unaffected in all the examined systems. The obtained results suggest partial dissolution of the polymeric components of the blend and, therefore, a modified Fox equation was used to assess the amount of PC dissolved in the SAN phase of ABS and vice versa.Reinforcing with OMMT enhances the miscibility of ABS and PC phases in ABS/PC blends and gives the best performance in terms of tensile strength, modulus of elasticity, and storage modulus, especially in 50/50 (w/w) ABS/PC blends. The addition of ABS‐g‐MAH compatibilizer, despite the improvement of intercalation process in organoclay/ABS/PC nanocomposites, did not seem to have any substantial effect on the mechanical properties of the examined blends. POLYM. COMPOS., 35:1395–1407, 2014. © 2013 Society of Plastics Engineers     

Properties of electropolymerized polycarboxyphenylmethacrylamide matrices/graphite fiber composites: Crosslinking effect

Imide formation from -CONH and -COOH functional groups of 2-carboxyphenylmethacrylamide (2-CPM), 4-carboxyphenylmethacrylamide (4-CPM), 4-carboxyphenyl methacrylamide/methylmethacrylate (4-CPM/MMA) and 4-carboxyphenylmethacrylamide/N-phenylmalemide (4-CPM/NPMI) electropolymerized matrices was investigated. It was found that 2-CPM polymers undergo intramolecular imidization and anhydride formation, which result in a small amount of crosslinked network. On the other hand, the thermally cured 4-CPM polymer demonstrates a significant increase in gel fraction. T_g and dynamic storage modulus, owing to crosslinked network formation. T_gs of 4-CPM/MMA and 4-CPM/NPMI composites measured by thermomechanical analysis after thermal heating were increased and were correlated very well with the preheating time. The 4-CPM/MMA composites with a particle crosslinking (T_g increased to 245°C) maintained a higher Izod impact strength than a typical epoxy composite (200 kJ/m² vs. 100 kJ/m²). Upon heating to promote crosslinking, a lower shear strength (65 MPa) of a 4-CPM/MMA composite increased to a strength of 78 MPa, close to the 80 MPa of an epoxy composite at 67% fiber volume fraction. A lower water absorption of around 1% was associated with the increased crosslinking. The mechanical properties of the 4-CPM/NPMI composites showed a similar trend upon preheating.     

Effect of EPDM‐g‐MAH on the morphology and properties of PA6/EPDM/HDPE ternary blends

The formation of core‐shell morphology within the dispersed phase was studied for composite droplet polymer‐blend systems comprising a polyamide‐6 matrix, ethylene‐propylene‐diene terpolymer (EPDM) shell and high density polyethylene (HDPE) core. In this article, the effect of EPDM with different molecular weights on the morphology and properties of the blends were studied. To improve the compatibility of the ternary blends, EPDM was modified by grafting with maleic anhydride (EPDM‐g‐MAH). It was found that core‐shell morphology with EPDM‐g‐MAH as shell and HDPE as core and separated dispersion morphology of EPDM‐g‐MAH and HDPE phase were obtained separately in PA6 matrix with different molecular weights of EPDM‐g‐MAH in the blends. DSC measurement indicated that there may be some co‐crystals in the blends due to the formation of core‐shell structure. Mechanical tests showed that PA6/EPDM‐g‐MAH/HDPE ternary blends with the core‐shell morphology exhibited a remarkable rise in the elongation at break. With more perfect core‐shell composite droplets and co‐crystals, the impact strength of the ternary blends could be greatly increased to 51.38 kJ m^?2, almost 10 times higher than that of pure PA6 (5.50 kJ m^?2). POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Morphology and mechanical properties of ABS blends prepared from emulsion‐polymerized PB‐g‐SAN impact modifier with AIBN as initiator

A series of PB‐g‐SAN impact modifiers (polybutadiene particles grafted by styrene and acrylonitrile) are synthesized by seed emulsion copolymerization initiated by oil‐soluble initiator, azobisiobutyronitrile (AIBN). The ABS blends are obtained by mixing SAN resin with PB‐g‐SAN impact modifiers. The mechanical behavior and the phase morphology of ABS blends are investigated. The graft degree (GD) and grafting efficiency (GE) are investigated, and the high GD shows that AIBN has a fine initiating ability in emulsion grafting of PB‐g‐SAN impact modifiers. The morphology of the rubber particles is observed by the transmission electron microscopy (TEM). The TEM photograph shows that the PB‐g‐SAN impact modifier initiated by AIBN is more likely to form subinclusion inside the rubber particles. The dynamic mechanical analysis on ABS blends shows that the subinclusion inside the rubber phase strongly influences the T_g, maximum tan δ, and the storage modulus of the rubber phase. The mechanical test indicates that the ABS blends, which have the small and uniform subinclusions dispersed in the rubber particles, have the maximum impact strength. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effects of the polybutadiene/poly(styrene‐co‐acrylonitrile) ratio in a polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) impact modifier on the morphology and mechanical behavior of acrylonitrile–butadiene–styrene blends

Polybutadiene‐g‐poly(styrene‐co‐acrylonitrile) (PB‐g‐SAN) impact modifiers with different polybutadiene (PB)/poly(styrene‐co‐acrylonitrile) (SAN) ratios ranging from 20.5/79.5 to 82.7/17.3 were synthesized by seeded emulsion polymerization. Acrylonitrile–butadiene–styrene (ABS) blends with a constant rubber concentration of 15 wt % were prepared by the blending of these PB‐g‐SAN copolymers and SAN resin. The influence of the PB/SAN ratio in the PB‐g‐SAN impact modifier on the mechanical behavior and phase morphology of ABS blends was investigated. The mechanical tests showed that the impact strength and yield strength of the ABS blends had their maximum values as the PB/SAN ratio in the PB‐g‐SAN copolymer increased. A dynamic mechanical analysis of the ABS blends showed that the glass‐transition temperature of the rubbery phase shifted to a lower temperature, the maximum loss peak height of the rubbery phase increased and then decreased, and the storage modulus of the ABS blends increased with an increase in the PB/SAN ratio in the PB‐g‐SAN impact modifier. The morphological results of the ABS blends showed that the dispersion of rubber particle in the matrix and its internal structure were influenced by the PB/SAN ratio in the PB‐g‐SAN impact modifiers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2165–2171, 2005     

Preparation of HDPE/SEBS‐g‐MAH and its effect on mechanical properties of HDPE/wood flour composites

In this article, high density polyethylene/styrene‐ethylene‐butylene‐styrene block copolymer blends (HDPE/SEBS) grafted by maleic anhydride (HDPE/SEBS‐g‐MAH), which is an effective compatibilizer for HDPE/wood flour composites was prepared by means of torque rheometer with different contents of maleic anhydride (MAH). The experimental results indicated that MAH indeed grafted on HDPE/SEBS by FTIR analysis and the torque increased with increasing the content of maleic anhydride and dicumyl peroxide (DCP). Styrene may increase the graft reaction rate of MAH and HDPE/SEBS. When HDPE/SEBS MAH was added to HDPE/wood flour composites, tensile strength and flexural strength of composites can reach 25.9 and 34.8 MPa in comparison of 16.5 and 23.8 MPa (without HDPE/SEBS‐g‐MAH), increasing by 157 and 146%, respectively. Due to incorporation of thermoplastic elastomer in HDPE/SEBS‐g‐MAH, the Notched Izod impact strength reached 5.08 kJ m^?2, increasing by 145% in comparison of system without compatibilizer. That HDPE/SEBS‐g‐MAH improved the compatibility was also conformed by dynamic mechanical measurement. Scanning electron micrographs provided evidence for strong adhesion between wood flour and HDPE matrix with addition of HDPE/SEBS‐g‐MAH. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Thermogravimetric Analysis of a Cellulosic Fabric Incorporated by Lithium Hydroxide as a Flame Retardant

The PVC/Polyhedral oligomeric silsesquioxanes containing octyl groups (O-POSS) nanocomposites were prepared. Plastic behavior and dyanmic rheology of nanocomposites were investigated. Influences of composition on storage modulus, loss modulus and complex viscosity were discussed. The mechanical properties and morphology were determined. The results show that both plastic time and balance torque of nanocomposites all decreased when O-POSS was added. The impact strength of nanocomposites can increase 8kJ/m² when O-POSS content is 1.5 wt%, but the T _g is not decreased. The O-POSS can be used as an efficient process aid and impact aid for PVC at low content.     

The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers