Removal of methylene blue from aqueous solution by a carbon-microsilica composite adsorbent

Microsilica, one kind of industrial solid waste material, was utilized firstly to prepare a carbon-microsilica composite adsorbent (CMS). The prepared adsorbent was characterized with XPS, SEM and Gas sorption experiments. The results indicated the SO₃H groups, which are very effective in capturing cationic organic dye, were introduced onto the surface of CMS; the Brunauer-Emmett-Teller (BET) surface area (S _BET ) and total pore volume (V _total ) of CMS reach 51m²/g and 0.045 cm³/g, respectively. Meanwhile, the possibility of the utilization of the adsorbent for removal of methylene blue (MB) from aqueous solution was investigated. The effect of pH, contact time and initial MB concentration for MB removal were studied. Equilibrium data were modeled using the Langmuir, Freundlich and Dubinin-Radushkevich equations to describe the equilibrium isotherms. It was found that data fit to the Langmuir equation better than the Freundlich equation. Maximum monolayer adsorption capacity was calculated at different temperatures (298, 308, and 318 K) reach 251.81, 283.76 and 309.70 mg/g, respectively. It was observed that adsorption kinetics obeys the pseudo-first-order equation.     

Removal of cationic dyes from aqueous solutions by kaolin: Kinetic and equilibrium studies

Experimental investigations were carried out using commercially available kaolin to adsorb two different toxic cationic dyes namely crystal violet and brilliant green from aqueous medium. Kaolin was characterized by performing particle size distribution, BET surface area measurement and XRD analysis. The effects of initial dye concentration, contact time, adsorbent dose, stirring speed, pH, salt concentration and temperature were studied in batch mode. The extent of adsorption was strongly dependent on pH of solution. Free energy of adsorption (ΔG⁰), enthalpy (ΔH⁰) and entropy (ΔS⁰) changes were calculated. Adsorption kinetic was verified by pseudo-first-order, pseudo-second-order and intra-particle-diffusion models. The rate of adsorption of both crystal violet and brilliant green followed the pseudo-second-order model for the dye concentrations studied in the present case. The dye adsorption process was found to be external mass transfer controlled at earlier stage and intra-particle diffusion controlled at later stage. Calculated external mass transfer coefficient showed that crystal violet dye adsorbed faster than brilliant green on kaolin. Adsorption of crystal violet and brilliant green on kaolin followed the Langmuir adsorption isotherm.     

Removal of methylene blue dye from aqueous solution by activated carbon prepared from cashew nut shell as a new low-cost adsorbent

Methylene blue dye was adsorbed on an adsorbent prepared from cashew nut shell. A batch adsorption study was carried out with variable adsorbent amount, initial dye concentration, contact time and pH. Studies showed that the pH of aqueous solutions affected dye removal as a result of removal efficiency increased with increasing solution pH. The experimental data were analyzed by the Langmuir, Freundlich, Redlich-Peterson, Koble-Corrigan, Toth, Temkin, Sips and Dubinin-Radushkevich models of adsorption using MATLAB 7.1. The experimental data yielded excellent fits within the following isotherm order: Redlich-Peterson>Toth>Sips>Koble-Corrigan>Langmuir>Temkin>Dubinin-Radushkevich>Freundlich, based on its correlation coefficient values. Three simplified kinetic models including a pseudofirst-order, pseudo-second-order and intraparticle diffusion equations were selected to follow the adsorption process. It was shown that the adsorption of methylene blue could be described by the pseudo-second-order equation. The results indicate that cashew nut shell activated carbon could be employed as a low cost alternative to commercial activated carbon in the removal of dyes from wastewater.     

Adsorption of methylene blue from aqueous solution by kaolin and zeolite

In the present study, kaolin and zeolite have been utilized as adsorbents for the removal of a cationic dye, methylene blue (MB), from aqueous solution within a batch process. Characterization of the two adsorbents was carried out by nitrogen adsorption–desorption experiments (specific surface area measurements by the BET method). The effects of various parameters such as initial MB concentration, contact time, adsorbent concentration, stirring speed, solution pH and salt concentration were examined and optimal experimental conditions were determined. The kinetic data were analyzed using pseudo-first-order and pseudo-second-order models. The mass transfer model in terms of interlayer diffusion was applied to the experimental data to examine the mechanisms of the rate controlling step. In order to determine the best-fit-isotherm, the experimental data were analyzed by the Freundlich, Temkin, and Dubinin–Radushkevich equation which are found to best represent the equilibrium data for kaolin and zeolite. The values of activation parameters such as free energy (ΔG), enthalpy (ΔH) and entropy (ΔS) were also determined. The results indicate that kaolin and zeolite could be interesting alternative materials with respect to more costly adsorbents used for dye removal.     

Removal of methylene blue from aqueous solutions by adsorption onto chemically activated halloysite nanotubes

This study examines the adsorption behavior of methylene blue (MB) from aqueous solutions onto chemically activated halloysite nanotubes. Adsorption of MB depends greatly on the adsorbent dose, pH, initial concentration, temperature and contact time. The Langmuir and Freundlich models were applied to describe the equilibrium isotherms and the Langmuir model agrees very well with experimental data. The maximum adsorption capacities for MB ranged from 91.32 to 103.63 mg·g⁻¹ between 298 and 318 K. A comparison of kinetic models applied to the adsorption data was evaluated for pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion equation. The results showed the adsorption process was well described by the pseudo-second-order and intra-particle diffusion mode. Thermodynamic parameters suggest that the adsorption is spontaneous and endothermic. The obtained results indicated that the product had the potential to be utilized as low-cost and effective alternative for dye removal in wastewater.     

Removal of methylene blue from aqueous solution by adsorption onto zeolite synthesized from coal fly ash and its thermal regeneration

BACKGROUND: The removal of cationic dyes from wastewater is of great importance. Three zeolites synthesized from coal fly ashes (ZFAs) were investigated as adsorbents to remove methylene blue (MB), a cationic dye, from aqueous solutions. Experiments were conducted using the batch adsorption technique under different conditions of initial dye concentration, adsorbent dose, solution pH, and salt concentration. RESULTS: The adsorption isotherm data of MB on ZFAs were fitted well to the Langmuir model. The maximum adsorption capacities of MB by the three ZFAs, calculated using the Langmuir equation, ranged from 23.70 to 50.51 mg g^?1. The adsorption of MB by ZFA was essentially due to electrostatic forces. The measurement of zeta potential indicated that ZFA had a lower surface charge at alkaline pH, resulting in enhanced removal of MB with increasing pH. MB was highly competitive compared with Na⁺, leading to only a < 6% reduction in adsorption in the presence of NaCl up to 1.0 mol L^?1. Regeneration of used ZFA was achieved by thermal treatment. In this study, 90–105% adsorption capacity of fresh ZFA was recovered by heating at 450 °C for 2 h. CONCLUSION: The experimental results suggest that ZFA could be employed as an adsorbent in the removal of cationic dyes from wastewater, and the adsorptive ability of used ZFA can be recovered by thermal treatment. Copyright © 2010 Society of Chemical Industry     

Application of succinylated sugarcane bagasse as adsorbent to remove methylene blue and gentian violet from aqueous solutions - Kinetic and equilibrium studies

In a previous work, succinylated sugarcane bagasse (SCB 2) was prepared from sugarcane bagasse (B) using succinic anhydride as modifying agent. In this work the adsorption of cationic dyes onto SCB 2 from aqueous solutions was investigated. Methylene blue, MB, and gentian violet, GV, were selected as adsorbates. The capacity of SCB 2 to adsorb MB and GV from aqueous single dye solutions was evaluated at different contact times, pH, and initial adsorbent concentration. According to the obtained results, the adsorption processes could be described by the pseudo-second-order kinetic model. Adsorption isotherms were well fitted by Langmuir model. Maximum adsorption capacities for MB and GV onto SCB 2 were found to be 478.5 and 1273.2 mg/g, respectively.     

Removal of arsenic from aqueous media using zeolite/chitosan nanocomposite membrane

In this work, the removal of arsenic (III) using zeolite/chitosan nanocomposite membranes was studied and characterized using scanning electron microscopy (SEM), atomic force microscope (AFM), etc. The water contact angle of the membrane decreased from 74.2 to 59.2° and the porosity of the prepared membranes increased from 20.38 to 45.81% with an increase in the concentration of zeolite. The rejection of arsenic (III) increases with increase in the zeolite loading for 500 and 1000 µg/L; but at 100 and 150 µg/L, the trend was opposite. The membrane with 1.0 [Chi-Z (1.0)] and 1.25 [Chi-Z (1.25)] wt% zeolite showed the highest rejection (>94%) for 1000 µg/L concentration of arsenic trioxide aqueous solution.     

Citric acid modified waste cigarette filters for adsorptive removal of methylene blue dye from aqueous solution

Waste cigarette filters (CFs) were recycled and modified with a nontoxic and low-cost citric acid (CA). The modified CFs were employed in the adsorptive removal of methylene blue (MB) dye from aqueous medium. The influence of pH, contact time, initial dye concentration, and adsorbent dose on adsorption of MB dye was evaluated. The adsorption studies were conducted by employing linear and nonlinear Langmuir and Freundlich isotherm models. The adsorption capacity of CF obtained through linear and nonlinear Langmuir model were 88.02 and 94 mg g⁻¹, which improved up to 163.93 and 168.81 mg g⁻¹, respectively, after the introduction of functional groups in CF-CA. The adsorption kinetics data were well fitted by pseudo-second order kinetics with coefficient of regression (R²) closed to unity. The removal efficiency of CF-CA was 97% at equilibrium time of 4 h. Desorption studies indicated that CF-CA could be regenerated by using HCl (0.1 M) and desorption efficiency was up to 82% upon second cycle of reusability experiment. This study proposed a green and economical use of recycled CFs in dyes wastewater treatment, simultaneously reducing the negative environmental impact due to their improper disposal.     

Removal of acid blue 113 and reactive black 5 dye from aqueous solutions by activated red mud

Removal of acid blue 113 (AB113) and reactive black 5 (RB5) dyes from aqueous solutions by activated red mud was investigated at different reaction parameters. Activated red mud has higher removal efficiency for AB113 than that for RB5. This can be explained by a greater molecular size of RB5 than that of AB113 and by different binding affinity with the surface of the activated red mud. Equilibrium data was fitted well with Freundlich isotherm and the kinetic data followed a pseudo second-order model. Maximum adsorption capacity was 83.33 mg/g and 35.58 mg/g at pH 3 for AB113 and RB5, respectively.     

Sorptive removal of methylene blue from aqueous solutions by polymer/activated charcoal composites

In this study, a new sorbent, a poly(acrylamide‐co‐itaconic acid) [P(AAm‐co‐IA)]/activated charcoal (AC) composite, was prepared by the aqueous polymerization of acrylamide and itaconic acid in the presence of AC with N,N′‐methylene bisacrylamide as a crosslinker and potassium persulfate as an initiator. The P(AAm‐co‐IA)/AC composite sorbent showed a fair capacity to adsorb the cationic dye methylene blue. The maximum sorption capacity, as studied at 23, 37, and 50°C and determined with the Langmuir isotherm model, was found to be 909.0, 312.5, and 192.3 mg/g, respectively. For an initial concentration of 5 mg/L, the kinetic uptake data were studied with various kinetic models. The pseudo‐second‐order equation was found to fairly fit the uptake data with a regression value of 0.999. The dye uptake increased with the pH of the sorbate solution, and the optimum pH was found to be in the range of 7–10. Intraparticle diffusion was also observed to take place, and the coefficient of intraparticle diffusion was evaluated to be 26.51 × 10^?2 mg g^?1 min^?1/2. The various thermodynamic parameters were also determined to predict the nature of the uptake process. The sorption process was found to be spontaneous, as indicated by a negative standard free energy change. The negative standard enthalpy change suggested an exothermic nature for the uptake. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Removal of boron from aqueous solution by composite chitosan beads

Various metal-oxide nanoparticles and chitosan were blended to form new adsorbents (M-Oxide-CTS) for removing boron from aqueous solutions in a batch system. The maximum boron adsorption capacity (q = 7.8 mg/g) was reached at pH = 4 within 5 min. Calculations based on Langmuir, Freundlich, and Dubinin–Radushkevich models showed the heterogeneous and physical nature of boron adsorption on M-Oxide-CTS. Modeling of the thermodynamic date indicated the nonspontaneous and exothermic process. The pseudo-second-order model adequately described the boron adsorption on M-Oxide-CTS. Desorption by means of alkaline solution at pH = 12 was carried out successfully.     

芝麻叶对亚甲基蓝吸附的动力学与热力学研究

以天然芝麻叶为吸附剂,亚甲基蓝(MB)为吸附质,考察芝麻叶吸附亚甲基蓝的动力学、热力学以及溶液pH值、吸附剂投入量、温度等对吸附的影响.采用准一级、准二级、颗粒内扩散吸附动力模型及Langmuir,Freundlich及Dubinin-Radushkevich(D-R)等温模型分别对吸附动力学和吸附等温线进行分析.结果...     

Adsorption of methylene blue from aqueous solutions by modified expanded graphite powder

The modified expanded graphite (MEG) powder was used as a porous adsorbent for the removal of the cationic dye, methylene blue (MB), from aqueous solutions. The dye adsorption experiments were carried out with the bath procedure. Experimental results showed that the basic pH, increasing initial dye concentration and high temperature favored the adsorption. The dye adsorption equilibrium was attained rapidly after 5 min of contact time. Experimental data related to the adsorption of MB on the MEG under different conditions were applied to the pseudo-first-order equation, the pseudo-second-order equation and the intraparticle diffusion equation, and the rate constants of first-order adsorption (k₁), the rate constants of second-order adsorption (k₂) and intraparticle diffusion rate constants (k_int) were calculated, respectively. The experimental data fitted very well in the pseudo-second-order kinetic model. The thermodynamic parameters of activation such as Gibbs free energy, enthalpy, and entropy were also evaluated. The results indicated that the MEG powder could be employed as an efficient adsorbent for the removal of textile dyes from effluents.     

Adsorption of methylene blue from aqueous solutions by synthetic montmorillonites of different compositions

The sorption capacity of synthetic montmorillonites of the composition Na_2x (Al_2(1–x),Mg_2x )Si₄O₁₀(OH)₂ · nH₂O (where 0 < x < 1) in relation to the methylene blue dye has been investigated. The obtained results from the data for natural samples of montmorillonite (K10) and activated carbon have been compared. The effect of the montmorillonite composition and the medium acidity on the degree of dye adsorption has been studied. The chemical composition of montmorillonite, which is optimal for solving tasks in the field of ecology and medicine, has been determined. The character of the interaction of montmorillonites with the adsorbed substance from the point of view of the physical-chemical sorption models has also been studied.     

Removal of methylene blue from aqueous solutions by poly(2-acrylamido-2-methylpropane sulfonic acid-co-itaconic acid) hydrogels

In this study, removal of methylene blue (MB) from aqueous solution by poly(AMPS-co-IA) hydrogels was examined by batch equilibration technique. The effects of monomer ratio, concentration of initiator and crosslinker, pH, adsorption time, initial dye concentration and adsorption temperature on the removal of MB were studied. The results show that the removal of MB was highly effected by preparation conditions of hydrogel. The maximum removal was observed at 10/90 IA/AMPS monomer ratio, 1.0% KPS, and 10.0% MBAAm concentrations. Removal of MB was strongly affected by pH. Pseudo-first-order, pseudo-second-order and intraparticle diffusion models were applied. It was concluded that adsorption of MB on hydrogel followed pseudo-second-order kinetics. It was found that the adsorption isotherm of the MB fit Langmuir-type isotherms. From the Langmuir equation, the adsorption capacity was found as 1,000 mg/g for MB dye. Thermodynamic parameters suggest that the adsorption is a typical physical process, spontaneous, and exothermic in nature. Ten adsorption—desorption cycles demonstrated that the hydrogels were suitable for repeated use without considerable change in adsorption capacity. The results revealed that this hydrogels have potential to be used as an adsorbent for the removal of MB from aqueous solution.     

Removal of methylene blue from aqueous solutions by using cold plasma‐ and formaldehyde‐treated onion skins

In this paper, the use of cold plasma‐treated and formaldehyde‐treated onion skins as a biosorbent has been investigated to remove methylene blue dye from aqueous solutions. The surface characteristics of the treated onion skins were investigated using Fourier Transform–infrared spectroscopy. The influence of process variables such as adsorbent dosage, initial dye concentration and pH were studied. Equilibrium isotherms were analysed by Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. The results indicated that the data for adsorption of methylene blue onto onion skins fitted well with the Langmuir isotherm model. The sorption capacities for cold plasma‐treated and formaldehyde‐treated onion skins by Langmuir isotherm were found to be 250 and 166.67 mg/g, respectively. The equilibrium time was found to be 150 min for 50 mg/l dye concentrations. The maximum removals for cold plasma‐treated and formaldehyde‐treated onion skins obtained were 90.94 and 95.54% at natural pH 10.0 for adsorbent doses of 0.15 g/200 ml, respectively. The rates of sorption were found to conform to pseudo‐first‐order kinetics. Results indicated that onion skins could be used as a biosorbent to remove methylene blue dye from contaminated waters.     

Removal of congo red from aqueous solutions by biogas waste slurry

Removal of Congo Red was carried out using biogas waste slurry as adsorbent at different concentrations of dye, adsorbent dosage, agitation time and pH. The process follows the first-order rate expression. The equilibrium data fit well in the Freundlich model of adsorption. Maximum removal of dye, 95%, was observed in the pH range 2.3–9.4. Desorption of Congo Red showed that it is solubilised in 50% acetic acid to the extent of 6% and the remainder appears to be chemically complexed irreversibly to the adsorbent. Low desorption of dye from the adsorbent surface in water indicates that the process may not be, essentially, a reversible one.     

Removal of Acid Red G dye from aqueous solutions by adsorption to MCM-41-layered double hydroxides composite

MCM-41 supported layered double hydroxides (LDH) composite materials (ML) were synthesized and studied for removal of Acid Red G (ARG), an anionic dye, with the adsorption method. ML was prepared using in situ synthesis procedure for the low supersaturation coprecipitation method, and ML10 and ML20 presented promising application towards ARG dye adsorption capacity in industrial wastewater. Powder samples were characterized by Xray diffraction, FTIR spectroscopy, scanning electron microscopy and energy dispersive spectrometry. The effects of different reaction time, initial solution pH and temperature on the dye adsorption capacity were investigated. Adsorption process was well described by pseudo-second-order kinetic model and Langmuir isotherm model. The fitting curves showed that ML10 and ML20 had higher adsorption rates and maintained a certain theoretical saturated adsorption capacity (92.19807mg/g and 96.41947mg/g, respectively) compared with LDH.