Characterization of gold supported on Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–CuO–Mn<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts obtained by thermal decomposition of aerosols

The purpose of this work was to employ the differential thermal analysis (DTA) technique to compare variations in the collapse energy of the zeolite Y crystalline structure in a fresh catalyst and in the same catalyst impregnated with nickel and vanadium. A small exothermic signal in the DTA curve at 950–1150 °C indicated the collapse of the crystalline structure. The areas of the exothermic signals in the DTA curves of the two samples indicated a reduction in the curve of the metal impregnated catalyst. These results were compared with X-ray data, leading to the conclusion that metal impregnation affects the zeolite Y crystalline structure and that the DTA technique is a potentially useful tool for measuring the integrity of zeolite Y in catalysts.     

Rapid synthesis of the low thermal expansion phase of Al<Subscript>2</Subscript>Mo<Subscript>3</Subscript>O<Subscript>12</Subscript> via a sol–gel method using polyvinyl alcohol

Aluminum molybdate was successfully synthesized using a simplified PVA assisted sol–gel method resulting in highly crystalline, monophasic (monoclinic P2₁/a) samples. These materials could readily be obtained at temperatures of 600 and 700 °C after calcining for as little as 15–20 min. Scanning electron microscopy and X-ray powder diffraction indicated that even the sample calcined at 600 °C for 20 min was free of impurities and composed of submicron sized particles (~300 nm). Transmission electron microscopy was used to confirm the monophasic character and submicron dimensions of the as-prepared powders. In addition to producing high quality samples, it was also observed that the metal to PVA ratio used during this simplified synthesis, could be used as a control parameter for tailoring the particle sizes of the final product.     

Synthesis and properties of γ-Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> solid solutions

The textural and structural properties of mixed oxides Ga₂O₃–Al₂O₃, obtained via impregnating γ-Al₂O₃ with a solution of Ga(NO₃)₃ and subsequent heat treatment, are studied. According to the results from X-ray powder diffraction, gallium ions are incorporated into the structure of aluminum oxide to form a solid solution of spinel-type γ-Ga₂O₃–Al₂O₃ up to a Ga₂O₃ content of 50 wt % of the total weight of the sample, accompanied by a reduction in the specific surface area, volume, and average pore diameter. It is concluded that when the Ga₂O₃ content exceeds 50 wt %, the β-Ga₂O₃ phase is observed along with γ-Ga₂O₃–Al₂O₃ solid solution. ⁷¹Ga and ²⁷Al NMR spectroscopy shows that gallium replaces aluminum atoms from the tetrahedral position to the octahedral coordination in the structure of γ-Ga₂O₃–Al₂O₃.     

Physicochemical properties of precursors of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–ZrO<Subscript>2</Subscript> oxide ceramics prepared by electrochemical method

Scanning electron microscopy, X-ray, and thermal analysis are used to examine the structure and properties of dispersive systems based on aluminum and zirconium oxides prepared electrochemically. The effect the conditions of synthesis have on the structure and morphology of Al₂O₃–ZrO₂ particles is studied. It is shown that the effect of an electric field on the reaction medium allows us to adjust the physicоchemical properties and morphology.     

Pd/Ga<Subscript>2</Subscript>O<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for the selective liquid-phase hydrogenation of acetylene to ethylene

The structure of Ga₂O₃–Al₂O₃ supports and Pd/Ga₂O₃–Al₂O₃ catalysts and the performance of these catalysts in liquid-phase acetylene hydrogenation have been investigated. The deposition of Ga(NO₃)₃ onto Al₂O₃ by impregnation followed by calcination of the impregnated support at 600°C yields γ-Ga₂O₃–Al₂O₃ solid solutions containing up to 50 wt % Ga₂O₃. X-ray diffraction characterization of model palladium catalysts and their temperature-programmed reduction with hydrogen have demonstrated that, while palladium in Pd/Ga₂O₃ is in the form of a Pd₂Ga alloy, in the Pd/γ-Ga₂O₃–Al₂O₃ catalyst there is no direct interaction between PdО and Ga₂O₃ particles and palladium is in the monometallic state. The introduction of 10–20 wt % gallium oxide into Al₂O₃ lowers the activity of the supported palladium catalyst relative to that of the initial Pd/Al₂O₃ but increases the ethylene yield by enhancing the ethylene formation selectivity.     

Hydrocracking of vacuum gas oil in the presence of catalysts NiMo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–amorphous aluminosilicates and NiW/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–amorphous aluminosilicates

Supported nickel–molybdenum and nickel–tungsten hydrocracking catalysts prepared using a support that consists of 70% Al₂O₃ and 30% amorphous aluminosilicate were characterized by nitrogen and mercury porosimetry, IR spectroscopy of adsorbed CO, and high-resolution electron microscopy. The catalytic tests in hydrocracking of vacuum gas oil containing 3.39% sulfur showed that the nature of the hydrogenating component (NiMo or NiW) only slightly influences the vacuum gas oil conversion and the diesel fraction yield, but noticeable influences the properties of the diesel fraction obtained. The catalyst NiMo/Al₂O₃–amorphous aluminosilicates, compared to NiW/Al₂O₃–amorphous aluminosilicates, ensures lower sulfur content in the diesel fraction obtained, whereas the catalyst NiW/Al₂O₃–amorphous aluminosilicates allows obtaining a diesel fraction with lower content of polyaromatic compounds.     

Atmospheric control of gel-oxide transformation in sol–gel derived Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-Y<Subscript>2</Subscript>O<Subscript>3</Subscript> fibers

Via sol–gel processing metal–organic fibers were produced and dried up to 140 °C. For these gel fibers the influence of a treatment in different atmospheres was investigated for the temperature range of 200–850 °C. The atmospheres were nitrogen, water vapor, evaporated nitric and hydrochloric acid and evaporated hydrogen peroxide. In the presence of moisture and especially with acidic moisture fibers were transformed almost completely to their oxide composition (82 mol% Al₂O₃·18 mol% Y₂O₃). In these inorganic amorphous structures considerable differences were observed on several structural levels. On the atomic scale, the coordination of Al ions was investigated by ²⁷Al MAS NMR and skeletal density by He-pycnometry. Porosity in the nm scale was characterized by N₂-sorption. As a macroscopic effect of different treatment atmospheres, the longitudinal shrinkage was observed. For fibers treated at 500 °C the relative shrinkage varied by 100% (comparing water vapor and nitrogen atmosphere). No simple correlation between the release of organic constituents, the formation of porosity and the shrinkage could be found. These aspects were controlled by the rigidity of the inorganic network against atomic reconstitution. The kind of atmosphere was found to be an effective parameter to control various aspects of the xerogel structure.     

Improvement of supercooling and thermal conductivity of the sodium acetate trihydrate for thermal energy storage with α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> as addictive

In situ calorimetric technology was firstly employed to study the effects of surfactants on the materials formation. In the present study, different kinds of surfactants were selected as additives during cluster-shaped Ni-doped Fe₃O₄ synthesis. Experimental results indicate that the surfactants reduced the particle size and changed the cationic distribution, compositions and magnetic properties of the as-synthesized materials. The microcalorimetric results demonstrate that the sample formation was endothermal and divided into five processes based on the heat-flow versus time curves. No significant effects of the surfactants on these processes were found. However, the surfactants addition affected the heat flow and the temperatures for peaks in these curves. The surfactant adsorption on the crystal facet and nuclei of the sample, and the interactions among surfactants and ions contained in the system may be mainly the reason for these effects. These results demonstrate different actions of surfactants and ligands on materials formation.     

Modeling and optimization of densification of nanocrystalline Al<Subscript>2</Subscript>O<Subscript>3</Subscript> powder prepared by a sol–gel method using response surface methodology

Response surface methodology (RSM) based on central composite design (CCD) was successfully applied to the optimization and modeling of densification of nanocrystalline Al₂O₃ powder prepared by sol–gel method. The effects of three operating variables, sintering temperature, calcination temperature and milling time on the densification of nanocrystalline Al₂O₃ were systematically evaluated. A quadratic model for densification was proposed. Analysis of variance (ANOVA) indicated that the proposed quadratic model could be used to navigate the design space. The simulated values obtained from the statistical model were in conformity with the experimental results within an average error of ±1.5%. The optimum operating conditions for densification were found to be 1,579 °C of sintering temperature, 909 °C of calcination temperature and 117 min of milling time. The obtained density under the optimum conditions determined by RSM was 98.5%. The results confirmed that RSM based on central composite design was an accurate and reliable method to optimize the densification conditions of nanocrystalline Al₂O₃ powder.     

Thermal studies of ZnO–B<Subscript>2</Subscript>O<Subscript>3</Subscript>–P<Subscript>2</Subscript>O<Subscript>5</Subscript>–TeO<Subscript>2</Subscript> glasses

The effect of TeO₂ additions on the thermal behaviour of zinc borophosphate glasses were studied in the compositional series (100 − x)[0.5ZnO–0.1B₂O₃–0.4P₂O₅]–xTeO₂ by differential scanning calorimetry, thermodilatometry and heating microscopy thermal analysis. The addition of TeO₂ to the starting borophosphate glass resulted in a linear increase of glass transition temperature and dilatometric softening temperature, whereas the thermal expansion coefficient decreased. Most of glasses crystallize under heating within the temperature range of 440–640 °C. The crystallization temperature steeply decreases with increasing TeO₂ content. The lowest tendency towards crystallization was observed for the glasses containing 50 and 60 mol% TeO₂. X-ray diffraction analysis showed that major compounds formed by annealing of the glasses were Zn₂P₂O₇, BPO₄ and α-TeO₂. Annealing of the powdered 50ZnO–10B₂O₃–40P₂O₅ glass leads at first to the formation of an unknown crystalline phase, which is gradually transformed to Zn₂P₂O₇ and BPO₄ during subsequent heating.     

P/RS intergrowth type phases in the Ln<Subscript>2</Subscript>O<Subscript>3</Subscript>–MO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> systems

Regularities of formation of complex aluminates with structure of P/RS intergrowth type phases in the Ln₂O₃–MO–Al₂O₃ systems (Ln = rare-earth element, M = Mg, Ca, Sr, Ba) have been considered. Systematization of the data on formation of complex compounds coexisting with one-layer phases in the Ln₂O₃–MO–Al₂O₃ systems and analysis of geometry criteria of LnMAlO₄ stability is a promising approach to prediction of novel compounds with structure of Ruddlesden–Popper phase.     

Optimization of process conditions for biodiesel production over CaO–Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/ZrO<Subscript>2</Subscript> catalyst using response surface methodology

CaO–Al₂O₃/ZrO₂ mixed oxide catalyst was prepared using free-solvent method. The catalyst was characterized using X-ray diffraction, BET surface area, acidity index (obtained by titration method), and scanning electron microscopy (SEM). With calcium aluminate and calcium zirconate been successfully formed, the mix exhibited small crystal size, high acidity, and large surface area, pore size, and pore volume, making it a catalyst of choice for biodiesel production. The activity of catalyst was evaluated in the course of esterification of oleic acid as well as transesterification of waste cooking oil (WCO) into biodiesel. Based on a four-variable central composite design (CCD), response surface methodology (RSM) was used to optimize effective variables on oleic acid conversion. The optimum yield of 94.68% was obtained at the following set of optimum conditions: reaction temperature of 120 °C, methanol/oleic acid molar ratio of 15.64, catalyst concentration of 2.94 wt%, and reaction time of 4 h; the result was in excellent agreement with the predicted values. Furthermore, under the optimum conditions, the catalyst succeeded to convert 93.48% of WCO into biodiesel.     

Heat-Treatment-Induced Evolution of the Mesostructure of Finely Divided Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript> Produced by the Sol–Gel Method

A method was developed for the low-temperature sol–gel synthesis of one of the most popular components of functional and structural materials—nanostructured yttrium aluminum garnet Y₃A_l5O₁₂—using precursors from the class of alkoxoacetylacetonates produced from the corresponding acetylacetonates. It was determined that increasing duration of heat treatment of yttrium-aluminum-containing xerogen in air to 6 h reduces the crystallization temperature of the Y₃A_l5O₁₂ phase from 920–930 to 750–800°C, which was confirmed by IR spectroscopy and X-ray powder diffraction analysis. The microstructure of nanocrystalline yttrium aluminum garnet obtained at 800°С was studied; it was found that the size of crystallites is 30–40 nm, the size of particles is 30–50 nm, and the size of pores is 20–30 nm. Small-angle neutron scattering demonstrated that, in the powders synthesized at 700–800°C, there is structural ordering of the short-range type, whereas in the nanocrystalline samples heat-treated at a higher temperature (850°С), there is no such ordering.     

Luminescent properties of Sr<Subscript>3</Subscript>Al<Subscript>2</Subscript>O<Subscript>6</Subscript>: Eu,Pr prepared by sol–gel method

A new red-emitting long afterglow Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor was synthesized by sol–gel methods using Sr(NO₃)₂, Al(NO₃)₃·9H₂O, Eu(NO₃)₃ and Pr(NO₃)₃ as raw materials. The crystalline structure of the phosphor powders were characterized by X-ray diffraction. Luminescent properties of the phosphor powders were analyzed by the fluorescence spectrophotometer. Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor powders with single Sr₃Al₂O₆ phase were prepared at 1200 °C for 2 h in the reducing atmosphere. Pr³⁺ doped made the light intensity and the light-lasting time of Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphors improved. The emission peaks of the Sr₃Al₂O₆: Eu²⁺, Pr³⁺ phosphor powders lay at 612 nm with the excitation of 472 nm and the longest afterglow time could last for about 15 min at Pr³⁺ content of 0.06.     

Formation of solid solutions of multiferroics in the Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>–Nd<Subscript>2</Subscript>O<Subscript>3</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system

The sequence of phases appearance during the formation of Bi_1–xNd_xFeO₃ solid solutions in powder oxides mixtures of bismuth, neodymium, and iron has been determined. It has been shown that the closeness of the reaction mixture composition to that of the individual compound (BiFeO₃ or NdFeO₃) is essential for the realization of the series of phase transformations yielding solid solutions of multiferroics Bi_1–xNd_xFeO₃ as the final product, due to the prevalence of various interphase contacts in the starting reaction zone.     

Hydrodeoxygenation of Vegetable Oil on NiMoS/WO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Catalysts

Tungstate-containing aluminum oxide is suitable as a catalyst support for hydrodeoxygenation of sunflower oil, ensuring 81–83 wt % yield of liquid products at 380°С, 4.0 MPa, and feed space velocity of 1 h^–1. The catalyst acidity increases with increasing tungsten oxide content, leading to an increase in the content of decarboxylation/decarbonylation products and isoparaffins in the product mixture.     

Physicochemical properties of (CH<Subscript>3</Subscript>)<Subscript>2</Subscript>NH<Subscript>2</Subscript>Cl–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composites

Composite solid electrolytes were synthesized from the organic salt dimethylammonium chloride (1–x)C₂H₈NCl–xAl₂O₃. Their physicochemical properties were studied. In the starting C₂H₈NCl salt, there is a phase transition at 39°C accompanied by an increase in conductivity by two orders of magnitude. The conductivity of the high-temperature phase is 9.3 × 10^–6 S/cm at 160°C. A differential scanning calorimetry study showed that the salt in the composites spreads over the oxide surface and at x > 0.6 the salt melting enthalpy decreases to zero. The conductivity of the resulting composites was studied by impedance spectroscopy. It was shown that heterogeneous doping leads to a sharp increase in ion conductivity to 7.0 × 10^–3 S/cm at 160°C and a decrease in the activation energy to 0.55 eV.     

Effect of MoO<Subscript>3</Subscript> additions on the thermal stability and crystallization kinetics of PbO–Sb<Subscript>2</Subscript>O<Subscript>3</Subscript>–As<Subscript>2</Subscript>O<Subscript>3</Subscript> glasses

The present paper reports on the effect of MoO₃ on the glass transition, thermal stability and crystallization kinetics for (40PbO–20Sb₂O₃–40As₂O₃)_100−x –(MoO₃) _x (x = 0, 0.25, 0.5, 0.75 and 1 mol%) glasses. Differential scanning calorimetry (DSC) results under non-isothermal conditions for the studied glasses were reported and discussed. The values of the glass transition temperature (T _g) and the peak temperature of crystallization (T _p) are found to be dependent on heating rate and MoO₃ content. From the compositional dependence and the heating rate dependence of T _g and T _p, the values of the activation energy for glass transition (E _g) and the activation energy for crystallization (E _c) were evaluated and discussed. Thermal stability for (40PbO–20Sb₂O₃–40As₂O₃)_100−x –(MoO₃) _x glasses has been evaluated using various thermal stability criteria such as ΔT, H _r , H _g and S. Moreover, in the present work, the K _r(T) criterion has been considered for the evaluation of glass stability from DSC data. The stability criteria increases with increasing MoO₃ content up to x = 0.5 mol%, and decreases beyond this limit.     

Adsorption of chlorobenzene vapor on V<Subscript>2</Subscript>O<Subscript>5</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst under dynamic conditions

Adsorption dynamics of chlorobenzene vapors on a 5% V₂O₅/Al₂O₃ catalyst has been investigated using the frontal chromatography technique. The uptakes of chlorobenzene have been measured as a function of vapor concentration and adsorption equilibrium has been found to follow formally the Langmuir isotherm. The breakthrough time proved to be a linear function of the column length as expected. Breakthrough profiles have been reported for different experimental conditions and quantitatively fitted by a reduced lumped diffusion model. This model provides an analytical solution that facilitates engineering calculations. Model parameters show complex behavior as functions of stream characteristics and depend on column length. When empirical expressions relating model mass transfer coefficients with influencing variables are found the model demonstrates good accuracy in predicting column performance.