Pseudoreinforcement effect of multiwalled carbon nanotubes in epoxy matrix composites

The carbon nanotube possesses outstanding physical properties. Theoretically, adding carbon nanotubes into a polymer matrix can remarkably improve the mechanical properties of the polymer matrix. In the present work, a series of composites was prepared by incorporating multiwalled carbon nanotubes (MWNTs) into an epoxy resin. The influences of MWNT content and curing temperature on the flexural properties of the epoxy resin were investigated. The results showed that a very low MWNT content should be used to ensure homogeneous dispersion of MWNTs in the epoxy matrix. A higher MWNT content may lead to deteriorated mechanical properties of the composites because of the aggregation of MWNTs. A decline in the flexural properties of the neat epoxy resin with increasing curing temperature was found. However, under the same curing conditions, improvement in flexural properties was observed for the composite with the low MWNT content and a mild curing temperature. The improvement was far beyond the predictions of the traditional short‐fiber composite theory. In fact, this improvement should be attributed to the retarding effect of MWNTs on the curing reaction of epoxy matrix. Therefore, the improvement in the flexural properties was only a pseudoreinforcement effect, not a nano‐reinforcement effect of the MWNTs on the epoxy resin. Perhaps, it is better for MWNTs to be used as functional fillers, such as electrical or thermal conductive fillers, than as reinforcements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3664–3672, 2006     

Microstructural,mechanical, and thermal characteristics of recycled cellulose fiber‐halloysite‐epoxy hybrid nanocomposites

Epoxy hybrid‐nanocomposites reinforced with recycled cellulose fibers (RCF) and halloysite nanotubes (HNTs) have been fabricated and investigated. The dispersion of HNTs was studied by synchrotron radiation diffraction (SRD) and transmission electron microscopy (TEM). The influences of RCF/HNTs dispersion on the mechanical properties and thermal properties of these composites have been characterized in terms of flexural strength, flexural modulus, fracture toughness, impact toughness, impact strength, and thermogravimetric analysis. The fracture surface morphology and toughness mechanisms were investigated by SEM. Results indicated that mechanical properties increased because of the addition of HNTs into the epoxy matrix. Flexural strength, flexural modulus, fracture toughness, and impact toughness increased by 20.8, 72.8, 56.5, and 25.0%, respectively, at 1 wt% HNTs load. The presence of RCF dramatically enhanced flexural strength, fracture toughness, impact strength, and impact toughness of the composites by 160%, 350%, 444%, and 263%, respectively. However, adding HNTs to RCF/epoxy showed only slight enhancements in flexural strength and fracture toughness. The inclusion of 5 wt% HNTs into RCF/epoxy ecocomposites increased the impact toughness by 27.6%. The presence of either HNTs or RCF accelerated the thermal degradation of neat epoxy. However, at high temperature, samples reinforced with RCF and HNTs displayed better thermal stability with increased char residue than neat resin. POLYM. COMPOS. 2012. © 2012 Society of Plastics Engineers     

FRP composites based on different types of glass fibers and matrix resins: A comparative study

Flexural properties, impact energy, heat deflection temperature, and resistance to thermal and hydrothermal degradation of composites based on E-glass and N-glass fibers as the reinforcing agents, and epoxy, unsaturated polyester, phenolic, and epoxy-phenolic resin systems as the matrix materials were studied and compared. As a reinforcing agent E-glass fiber is superior to N-glass fiber, particularly with respect to development of flexural strength and modulus, impact strength, and thermal resistance; N-glass fiber, however, imparts to the composites substantially higher resistance to hydrothermal degradation under boiling conditions in different chemical environments. For use of both E-glass and N-glass fibers as reinforcing agents, the general order of resistance to hydrothermal degradation for the composites based on different matrix resins is epoxy > phenolic > unsaturated polyester resin. Incorporation of a low dose of a rubbery polymer, such as styrene butadiene rubber (0.1–0.2%) and liquid polybutadiene (0.5–0.75%), in unsaturated polyester resin as the matrix resin measurably enhances impact energy of the composite. © 1995 John Wiley & Sons, Inc.     

Toughened epoxy resin matrix for a membrane shell by wet filament winding

A toughened epoxy resin matrix was obtained with a reactive toughening agent and methyl hexahydrophthalic anhydride as a curing agent. The mechanical properties of the modified epoxy resin and its glass‐fiber‐reinforced composites were investigated systematically. The modified epoxy resin matrix possessed many good properties, including a high flexural strength (138 MPa), high elongation at break (5.2%), low viscosity, long pot life at room temperature, and good water resistance. In addition, the glass‐fiber‐reinforced composites showed a high strength conversion ratio of the glass fiber (86.7%) and good fatigue resistance. The results demonstrated that the modified epoxy resin matrix is very suitable for applications in reverse osmosis membrane shell products fabricated with wet filament winding for water treatment. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Carbon fiber cardanol-epoxy composites

Carbon fiber composites based on tetrafunctional epoxy resin N,N,N′,N′-tetraglycidyl-2,2-bis[4-(4-aminophenoxy)phenyl]propane modified with cardanol were investigated. The differential scanning calorimetric technique was used to study the curing reaction of the neat resins. The dielectric properties of the composites were compared. The use of cardanol in epoxy resins at cardanol/epoxy molar ratios less than 0.3/1 improved the chemical resistance as well as the mechanical properties of the composites, such as the flexural strength and modulus, tensile strength and modulus, and interlaminar shear strength. Higher cardanol contents decreased such properties. The highest properties of the composites were observed with the epoxy-cardanol resin having a cardanol/epoxy molar ratio of 0.3/1. © 1996 John Wiley & Sons, Inc.     

In‐situ reinforcement of PBT/ABS blends with liquid crystalline polymer

Ternary in‐situ poly(butylene terephthalate) (PBT)/poly(acrylonitrile‐butadienestyrene) (ABS)/liquid crystalline polymer(LCP) blends were prepared by injection molding. The LCP used was a versatile Vectra A950, and the matrix material was PBT/ABS 60/40 by weight. Maleic anhydride (MA) copolymer and solid epoxy resin (bisphenol type‐A) were used as compatibilizers for these blends. The tensile, dynamic mechanical, impact, morphology and thermal properties of the blends were studied. Tensile tests showed that the tensile stregth of PBT/ABS/LCP blend in the longitudinal direction increased markedly with increasing LCP content. However, it decreased sharply with increasing LCP content up to 5 wt%; thereafter it decreased slowly with increasing LCP content in the transverse direction. The modulus of this blend in the longitudinal direction appeared to increase considerably with increasing LCP content, whereas the incorporation of LCP into PBT/ABS blends had little effect on the modulus in the transverse direction. The impact tests revealed that the Izod impact strength of the blends in longitudinal direction decreased with increasing LCP content up to 10 wt%; thereafter it increased slowly with increasing LCP. Dynamic mechanical analyses (DMA) and thermogravimetric measurements showed that the heat resistance and heat stability of the blends tended to increase with increasing LCP content. SEM observation, DMA, and tensile measurement indicated that the additions of epoxy and MA copolymer to PBT/ABS matrix appeared to enhance the compatibility between PBT/ABS and LCP.     

动态固化聚丙烯／马来酸酐接枝聚丙烯／滑石粉／环氧树脂复合材料研究

将动态硫化技术应用于热塑性树脂／填料／热固性树脂复合体系，制备了动态固化聚丙烯(PP)／马来酸酐接枝PP(PP-g-MAH)/滑石粉(Talc)／环氧树脂(EP)复合材料。研究了动态固化PP／PP-g-MAH/Talc／EP复合材料的界面作用、形态结构、力学性能以及热稳定性。实验结果表明：PP／PP-g—MAH的加入，可明显增加PP/Talc复合材料的界面作用。在动态固化PP／PP-g-MAH/Talc／EP复合材料中，PP和Talc两相界面更加模糊，动态固化EP进一步增加了PP和Talc间的界面作用。当EP的用量超过5份时，部分EP呈颗粒状分布在PP基体中。与PP／PP-g-MAH/Talc／EP和PP／PP-MAH-Talc／EP复合材料相比，动态固化PP／PP-g-MAH/Talc／EP复合材料的冲击强度、拉伸强度和弯曲模量均有明显提高。当EP用量超过5份时，复合材料的冲击强度和断裂伸长率明显降低，但拉伸强度和弯曲模量继续增加。热分析表明动态固化PP／PP-g-MAH/Talc／EP复合材料具有较高的热稳定性。     

Properties of ternary in situ polycarbonate/polybutylene terephthalate/liquid crystalline polymer composites

Ternary in situ polycarbonate (PC)/polybutylene terephthalate (PBT)/liquid crystalline polymer (LCP) composites were prepared by injection molding. The liquid crystalline polymer used was a versatile Vectra A950. The matrix of composite was composed of PC/PBT 60/40 by weight. A solid epoxy resin (bisphenol type‐A) was used as a compatibilizer for the composites. Dynamic mechanical analysis (DMA) showed that epoxy resin was effective to improve the compatibility between PC and PBT, and between PC/PBT and LCP, respectively. Tensile tests revealed that the stiffness of composites shows little change with the LCP content up to 10 wt %. Above this concentration, the stiffness tended to increase with increasing LCP content. Furthermore, the tensile strengths appeared to increase with increasing LCP content, and their values were close to those predicted from the rule of mixtures. Scanning electron microscopic examination showed that LCP ribbons and short fibrils were developed in the composites containing LCP content ≤10 wt %. However, fine and elongated fibrils were formed in the skin and core sections of the composites when the LCP content reached 25 wt % and above. Thermogravimetric analysis indicated that the thermooxidative stability of the PC/PBT 60/40 blend tended to improve with increasing LCP content. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1827–1835, 1999     

Bisphenol A dicyanate–novolac epoxy blend: Cure characteristics,physical and mechanical properties,and application in composites

Reactive blends of bisphenol A dicyanate (BACY) and a novolac epoxy resin (EPN) were investigated for their cure behavior and the mechanical, thermal, and physical properties of the cocured neat resin and glass‐laminate composites. Contrary to the apparent observation in DSC, the dynamic mechanical analysis confirmed a multistep cure reaction of the blend, in league with an established reaction path for similar systems. The cured matrix was found to contain both polycyanurate and oxazolidinone networks that existed in discrete phases exhibiting independent glass transitions in dynamic mechanical analysis (DMA). The flexible and less crosslinked oxazolidinone network contributed to enhanced flexural strength at the cost of the tensile strength of the neat resin. The increased resin flexibility was, however, not translated to the glass‐laminate composite for which the flexural strength decreased with the oxazolidinone content, although the latter was conducive for rendering a stronger interphase. The presence of oxazolidinone adversely affected the thermal stability of the cured resin and the high‐temperature performance of both neat resin and the composites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1675–1685, 1999     

Preparation,morphology, and properties of silane‐modified MWCNT/epoxy composites

Both epoxy resin and acid‐modified multiwall carbon nanotube (MWCNT) were treated with 3‐isocyanatopropyltriethoxysilane (IPTES). Scanning electron microscopy (SEM) and transmission electronic microscope (TEM) images of the MWCNT/epoxy composites have been investigated. Tensile strength of cured silane‐modified MWCNT (1.0 wt %)/epoxy composites increased 41% comparing to the neat epoxy. Young's modulus of cured silane‐modified MWCNT (0.8 wt %)/epoxy composites increased 52%. Flexural strength of cured silane‐modified MWCNT (1.0 wt %)/epoxy composites increased 145% comparing to neat epoxy. Flexural modulus of cured silane‐modified MWCNT (0.8 wt %)/epoxy composites increased 31%. Surface and volume electrical resistance of MWCNT/epoxy composites were decreased with IPTES‐MWCNT content by 2 orders and 6 orders of magnitude, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical and anticorrosion properties of furan/epoxy‐based basalt fiber‐reinforced composites

A furan/epoxy blend applicable to composite manufacture was studied and corresponding basalt fiber‐reinforced composites were prepared. The processability, mechanical properties, and reasons for the improved mechanical properties of this blend were investigated by rheology machine, mechanical testing machine, and scanning electron microscopy. With excellent processability, furan/epoxy was suitable for manufacturing composites. Furan/epoxy with the ratio of 5/5 showed the best properties, and the impact strength, flexural strength and flexural modulus were 15.43 kJ/m², 102.81 MPa, and 3209.40 MPa, respectively. The river‐like fracture surface of the furan/epoxy system was well consistent with the mechanical properties. The mechanical and anti‐corrosive properties of basalt fiber‐reinforced furan/epoxy composites were also studied. The mechanical properties of composites changed the same as those of furan/epoxy matrix did. Furan resin effectively improved the anti‐acid but not anti‐alkali property of composites, probably because furan could be cured in acidic condition and basalt fiber was resistant to acid and alkali. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44799.     

纳米SiC改性氰酸酯树脂的性能及其作用机理研究

采用模塑成型法制备氰酸酯树脂(CE)/纳米SiC复合材料,通过冲击强度和弯曲强度测试,分别考察了纳米SiC及其经偶联剂KH-560表面处理后对CE/纳米SiC复合材料力学性能的影响,并通过理论分析探讨了其作用机理。结果表明,纳米SiC能够有效地改善复合材料的力学性能,而经KH-560表面处理的纳米SiC能进一步提高复合材料的冲击强度和弯曲强度;当纳米SiC含量为1 %时,CE/纳米SiC和CE/纳米SiC/KH-560复合体系的冲击强度分别提高了73.66 %和86.26 %,弯曲强度分别提高了20.85 %和29.56 %。     

Processing and characterization analysis of pyrolyzed oil rubber (from waste tires)‐epoxy polymer blend composite for lightweight structures and coatings applications

In this experimental investigation, the authors have fabricated and characterized composites made from pyrolysis oil rubber and epoxy resin. As the dumping of waste scrap tires poses a serious environmental threat, the pyrolysis oil rubber was extracted from these waste tires only. The prepared blend having pyrolysis oil with various weight percentages (wt%) was examined on the basis of various physical, microstructural, mechanical, and thermal tests. The microstructural tests (scanning electron microscopy and X‐ray diffraction) analysis complemented with the mechanical tests (tensile, compression, flexural, hardness, and impact) results and confirmed that the 4.4 wt% of pyrolysis oil in epoxy resin sample exhibited the best results in toughening of the polymer network. Furthermore, the thermal analysis (differential thermal analysis and thermogravimetric analysis), electrical conductivity, density, water absorption, gas chromatography–mass spectroscopy, and Fourier‐transform infrared tests for the composites were also performed. Low density and high tensile strength than neat epoxy resin makes this composite a potential candidate for fabricating lightweight structures and in polymer coatings for automotive industries. POLYM. ENG. SCI., 59:2041–2051, 2019. © 2019 Society of Plastics Engineers     

环氧树脂/短切碳纤维复合材料性能研究

制备出了短切碳纤维增强TDE-85环氧树脂复合材料,研究了碳纤维的含量对复合材料力学性能和耐热性能的影响。结果表明,碳纤维的加入有利于复合材料力学性能和耐热性能的提高,并在碳纤维含量为0.25%时,复合材料的拉伸强度、冲击韧性、弯曲强度和弯曲模量达到最大,分别提高了29.33%、25.31%、30.28%和68.93%。此外,对复合材料的弯曲断裂面进行了微观形貌分析,结果表明一定量的碳纤维可以较好地分散在树脂基体中,同时,碳纤维原丝和树脂基体的界面结合比较弱,主要依赖于两相之间的物理嵌合。     

The effect of recycling number on the mechanical,chemical, thermal,and rheological properties of PBT/PC/ABS ternary blends: With and without glass‐fiber

The recycling possibilities of poly(butylene terephthalate)/polycarbonate/acrylonitrile–butadiene–styrene (PBT/PC/ABS) ternary blend with and without glass‐fiber content were investigated using repeated injection molding process. In this study, PBT/PC/ABS ternary blends were reprocessed at five times and the results were presented after each recycling process. The recycling possibility of PBT/PC/ABS ternary blend was evaluated by measuring the mechanical, chemical, thermal, and rheological properties. Mechanical properties were determined by the tensile strength, yield strength, strain at break, elastic modulus, impact strength, flexural strength, and flexural modulus. Chemical and thermal properties were evaluated by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermal gravimetric analysis, and scanning electron microscopy. Rheological properties of the ternary blends were studied by melt flow index measurement. From the results, it was found that mechanical properties of recycled composites were better than virgin PBT/PC/ABS ternary blends. POLYM. COMPOS., 35:2074–2084, 2014. © 2014 Society of Plastics Engineers     

Special effect of epoxy resin E-44 on compatibility and mechanical properties of poly(butylene terephthalate)/polyamide-6 blends

An attempt was made to modify the properties of poly(butylene terephthalate) (PBT) by blending it with polyamide-6 (PA-6). Since PBT and PA-6 are incompatible, epoxy resin was used as a compatibilizer to form an alloy. Alloys of PBT and PA-6 with varying amounts (0–12%) of epoxy resin E-44 were prepared by melt blending. The notched Izod impact strength and flexural strength as a function of epoxy resin E-44 content were studied. Ultimate mechanical properties showed significant improvement on addition of epoxy resin E-44. The maximum increase of the notched Izod impact strength (≈600%) of PBT/PA-6 blends is obtained at 3% (weight) epoxy resin E-44 content. The impact fracture surfaces were studied using scanning electron microscopy (SEM): The SEM micrographs showed a noticeable change in the type of surface structure on adding epoxy resin E-44. DMTA also showed improved compatibility between PBT and PA-6 on adding epoxy resin E-44. DSC studies showed that the presence of epoxy resin E-44 hindered the crystallization of both PBT and PA-6 in the alloys. Wide-angle X-ray diffraction (WAXD) showed no obvious difference on crystallinity of PBT and PA-6 in the alloys with the presence of a small amount of epoxy resin E-44. © 1996 John Wiley & Sons, Inc.     

Utilization of Granite Powder as Filler in PC-Toughened Epoxy Resins: Studies on Physico-Mechanical Properties

The present study reports the possibility of using granite powder, an industrial waste with no end use, as potential filler in polycarbonate (PC)-toughened epoxy resin. Testing data for the physico-mechanical properties such as tensile, flexural, density and void content of the composites, according to the filler loading were catalogued. Incorporation of waste granite powder in toughened resin enhances the mechanical properties when compared to neat epoxy, but reduces significantly with respect to toughened resin matrix.     

纳米二氧化硅对PBT力学和结晶性能的影响

采用熔融共混的方法,将纳米SiO2添加到聚对苯二甲酸丁二醇酯(PBT)中,制备出PBT/纳米SiO2复合材料,对其力学和结晶性能进行分析研究。结果表明,随着纳米SiO2含量增加,PBT/纳米SiO2复合材料的拉伸强度和弯曲强度增加,PBT的结晶度增加,球晶尺寸减小,最大扭矩和平衡扭矩变化不大。当纳米SiO2含量为0.1份时,PBT的拉伸强度提高12%,断裂伸长率提高100%,冲击强度提高10%,弯曲强度提高5%,综合力学性能最好。     

碳纤维湿法缠绕用环氧树脂基体研究

以TDE-85树脂和AFG-90树脂为主体树脂,混合芳香胺为固化剂,研究了一种适合于碳纤维复合材料湿法缠绕成型的树脂配方。结果表明,该树脂的黏度低(＜550 mPa·s)、适用期长,其浇铸体具有优异的力学性能,其拉伸强度为107 MPa,拉伸模量为4．09 GPa,弯曲强度为161 MPa,弯曲模量为3．88 GPa,断裂伸长率超过6%。用其制备的T-700碳纤维缠绕复合材料界面粘接好,NOL环层间剪切强度达到66．8 MPa,拉伸强度达到2．44 GPa。     

Thermal and mechanical properties of poly(butylene terephthalate)/epoxy blends

In this study, melt blends of poly(butylene terephthalate) (PBT) with epoxy resin were characterized by dynamic mechanical analysis, differential scanning calorimetry, tensile testing, Fourier transform infrared spectroscopy, and wide‐angle X‐ray diffraction. The results indicate that the presence of epoxy resin influenced either the mechanical properties of the PBT/epoxy blends or the crystallization of PBT. The epoxy resin was completely miscible with the PBT matrix. This was beneficial to the improvement of the impact performance of the PBT/epoxy blends. The modification of the PBT/epoxy blends were achieved at epoxy resin contents from 1 to 7%. The maximum increase of the notched Izod impact strength (≈ 20%) of the PBT/epoxy blends was obtained at 1 wt % epoxy resin content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008