Using digital holographic microscopy for simultaneous measurements of 3D near wall velocity and wall shear stress in a turbulent boundary layer

A digital holographic microscope is used to simultaneously measure the instantaneous 3D flow structure in the inner part of a turbulent boundary layer over a smooth wall, and the spatial distribution of wall shear stresses. The measurements are performed in a fully developed turbulent channel flow within square duct, at a moderately high Reynolds number. The sample volume size is 90 × 145 × 90 wall units, and the spatial resolution of the measurements is 3–8 wall units in streamwise and spanwise directions and one wall unit in the wall-normal direction. The paper describes the data acquisition and analysis procedures, including the particle tracking method and associated method for matching of particle pairs. The uncertainty in velocity is estimated to be better than 1 mm/s, less than 0.05% of the free stream velocity, by comparing the statistics of the normalized velocity divergence to divergence obtained by randomly adding an error of 1 mm/s to the data. Spatial distributions of wall shear stresses are approximated with the least square fit of velocity measurements in the viscous sublayer. Mean flow profiles and statistics of velocity fluctuations agree very well with expectations. Joint probability density distributions of instantaneous spanwise and streamwise wall shear stresses demonstrate the significance of near-wall coherent structures. The near wall 3D flow structures are classified into three groups, the first containing a pair of counter-rotating, quasi streamwise vortices and high streak-like shear stresses; the second group is characterized by multiple streamwise vortices and little variations in wall stress; and the third group has no buffer layer structures.     

Lateral Spreading Mechanism of a Turbulent Spot and a Turbulent Wedge

We examine the spreading of turbulent spots and wedges into a surrounding laminar Blasius boundary layer. The spreading is not due to the lateral propagation of turbulent eddies but rather to a developing disturbance in the surrounding spanwise vorticity of the laminar boundary layer. We concentrate on the mechanisms for generating streamwise vorticity. In particular, inclined generally streamwise vortex tubes along the spot/wedge boundary tilt mean shear vortex lines either up or down. These lines subsequently tend to either lag back or lead forward. As the leading or lagging vortex lines continue to wrap around and reinforce the causative inclined tube, the lines arch up or down. The outboard portion of the resulting arch must acquire a vertical, ω_y, component of vorticity which induces the rollup of a new inclined tube now outboard of the first. Close to the wall the arching mechanism is inhibited by the no through flow boundary condition while far from the wall the process is inhibited by the lack of sufficient mean spanwise vorticity.     

Drag reduction of turbulent channel flows over an anisotropic porous wall with reduced spanwise permeability

The direct numerical simulation(DNS) is carried out for the incompressible viscous turbulent flows over an anisotropic porous wall. Effects of the anisotropic porous wall on turbulence modifications as well as on the turbulent drag reduction are investigated. The simulation is carried out at a friction Reynolds number of 180, which is based on the averaged friction velocity at the interface between the porous medium and the clear fluid domain. The depth of the porous layer ranges from 0.9 to 54 viscous units. The permeability in the spanwise direction is set to be lower than the other directions in the present simulation. The maximum drag reduction obtained is about 15.3% which occurs for a depth of 9 viscous units. The increasing of drag is addressed when the depth of the porous layer is more than 25 wall units. The thinner porous layer restricts the spanwise extension of the streamwise vortices which suppresses the bursting events near the wall. However, for the thicker porous layer, the wall-normal fluctuations are enhanced due to the weakening of the wall-blocking effect which can trigger strong turbulent structures near the wall.     

Periodicity of large-scale coherence in turbulent boundary layers

This study examines the pronounced periodicity of large-scale coherent structures in turbulent boundary layers, which are of the order of the boundary layer thickness (δ) and reside in the logarithmic and wake regions. To this end, a series of multi-camera planar particle image velocimetry (PIV) measurements are conducted in a streamwise/spanwise and streamwise/wall-normal planes at a friction Reynolds number of Re_τ ≈ 2500. The experiments are configured to capture a large field-of-view with velocity fields that cover a streamwise extent in excess of 15δ. The resulting vector fields reveal large-scale streamwise and spanwise organisation instantaneously, which is often lost when only examining mean statistics. By extracting the dominant streamwise and spanwise Fourier modes of the large-scale motions, a clearer picture of these structural organisations and coherence is presented. A targeted inspection of these dominant modes reveal that these features remain coherent over a significant fraction of the boundary layer thickness in the wall-normal direction, but only a fraction of them have coherence that extends to the wall (wall-coherent). Further, the spatial extents and the population density of these wall-coherent and wall-incoherent modes are characterised, with the former conforming to the attached eddy arguments of Townsend (1976) and the subsequent attached eddy models. Collectively, through the evidence gathered here, we provide a conceptual picture of the representative large-scale structures in turbulent boundary layers, which are likely to have implications on the type of representative structures to be used in structure-based models for these flows.     

The effect of streamwise vortices on the turbulence structure of a separating boundary layer

A high Reynolds number flat plate turbulent boundary layer is investigated in a wind-tunnel experiment. The flow is subjected to an adverse pressure gradient which is strong enough to generate a weak separation bubble. This experimental study attempts to shed some new light on separation control by means of streamwise vortices with emphasize on the change in the boundary layer turbulence structure. In the present case, counter-rotating and initially non-equidistant streamwise vortices become and remain equidistant and confined within the boundary layer, contradictory to the prediction by inviscid theory. The viscous diffusion cause the vortices to grow, the swirling velocity component to decrease and the boundary layer to develop towards a two-dimensional state. At the position of the eliminated separation bubble the following changes in the turbulence structure were observed. The anisotropy state in the near-wall region is unchanged, which indicates that it is determined by the presence of the wall rather than the large scale vortices. However, the turbulence in the outer part of the boundary layer becomes overall more isotropic due to an increased wall-normal mixing and a significantly decreased production of streamwise fluctuations. The turbulent kinetic energy is decreased as a consequence of the latter. Despite the complete change in mean flow, the spatial turbulence structure and the anisotropy state, the process of transfer of turbulent kinetic energy to the spanwise fluctuating component seems to be unchanged. Local regions of anisotropy are strongly connected to maxima in the turbulent production. For example, at spanwise positions in between those of symmetry, the spanwise gradient of the streamwise velocity cause significant production of turbulent fluctuations. Transport of turbulence in the spanwise direction occurs in the same direction as the rotation of the vortices.     

Turbulence modulation in a particle-laden flow over a hemisphere-roughened wall

Turbulence modulation by the inertia particles in a spatially developing turbulent boundary layer flow over a hemisphere-roughened wall was investigated using the direct numerical simulation method. The Eulerian and Lagrangian approaches were used for the gas- and particle-phases, respectively. An immersed boundary method was employed to resolve the hemispherical roughness element. The hemispheres were staggered in the downstream direction and arranged periodically in the streamwise and spanwise directions with spacing of p_x/d= 4 and p_z/d= 2 (where p_x and p_z are the streamwise and spanwise spacing of the hemispheres, and d is the diameter). The effects of particles on the turbulent coherent structures, turbulent statistics and quadrant events were analyzed. The results show that the addition of particles significantly damps the vortices structures and increases the length scales of streak structures. Compared with the particle-laden flow over the smooth wall, the existence of the wall roughness decreases the mean streamwise velocity in the near wall region, and makes the peaks of Reynolds stresses profiles shift up. In addition, the existence of particles also increases the percentage contributions to Reynolds shear stress from the Q4 events, however, decreases the percentage contributions from other quadrant events.     

Tomographic PIV investigation of coherent structures in a turbulent boundary layer flow

Tomographic particle image velocimetry was used to quantitatively visualize the three-dimensional coherent structures in the logarithmic region of the turbulent boundary layer in a water tunnel.The Reynolds number based on momentum thickness is Reθ = 2 460.The instantaneous velocity fields give evidence of hairpin vortices aligned in the streamwise direction forming very long zones of low speed fluid,which is flanked on either side by highspeed ones.Statistical support for the existence of hairpins is given by conditional averaged eddy within an increasing spanwise width as the distance from the wall increases,and the main vortex characteristic in different wall-normal regions can be reflected by comparing the proportion of ejection and its contribution to Reynolds stress with that of sweep event.The pre-multiplied power spectra and two-point correlations indicate the presence of large-scale motions in the boundary layer,which are consistent with what have been termed very large scale motions(VLSMs).The three dimen-sional spatial correlations of three components of velocity further indicate that the elongated low-speed and highspeed regions will be accompanied by a counter-rotating roll modes,as the statistical imprint of hairpin packet structures,all of which together make up the characteristic of coherent structures in the logarithmic region of the turbulent boundary layer(TBL).     

The spanwise spectra in wall-bounded turbulence

The pre-multiplied spanwise energy spectra of streamwise velocity fluctuations are investigated in this paper. Two distinct spectral peaks in the spanwise spectra are observed in low-Reynolds-number wall-bounded turbulence.The spectra are calculated from direct numerical simulation(DNS) of turbulent channel flows and zero-pressure-gradient boundary layer flows. These two peaks locate in the nearwall and outer regions and are referred to as the inner peak and the outer peak, respectively. This result implies that the streamwise velocity fluctuations can be separated into large and small scales in the spanwise direction even though the friction Reynolds number Reτ can be as low as 1000. The properties of the inner and outer peaks in the spanwise spectra are analyzed. The locations of the inner peak are invariant over a range of Reynolds numbers. However, the locations of the outer peak are associated with the Reynolds number,which are much higher than those of the outer peak of the pre-multiplied streamwise energy spectra of the streamwise velocity.     

Structure of the turbulent boundary layer over a rod-roughened wall

Turbulent coherent structures near a rod-roughened wall are scrutinized by analyzing instantaneous flow fields obtained from direct numerical simulations (DNSs) of a turbulent boundary layer (TBL). The roughness elements used are periodically arranged two-dimensional spanwise rods, and the roughness height is k/δ = 0.05 where δ is the boundary layer thickness. The Reynolds number based on the momentum thickness is varied in the range Re_θ = 300–1400. The effect of surface roughness is examined by comparing the characteristics of the TBLs over smooth and rough walls. Although introduction of roughness elements onto the smooth wall affects the Reynolds stresses throughout the entire boundary layer when scaled by the friction velocity, the roughness has little effect on the vorticity fluctuations in the outer layer. Pressure-strain tensors of the transport equation for the Reynolds stresses and quadrant analysis disclose that the redistribution of turbulent kinetic energy of the rough wall is similar to that of the smooth wall, and that the roughness has little effect on the relative contributions of ejection and sweep motions in the outer layer. To elucidate the modifications of the near-wall vortical structure induced by surface roughness, we used two-point correlations, joint weighted probability density function, and linear stochastic estimation. Finally, we demonstrate the existence of coherent structures in the instantaneous flow field over the rod-roughened surface.     

Near-field measurements and development of a new boundary layer over a flat plate with localized suction

Suction on a turbulent boundary layer is applied through a narrow strip in order to understand the effects suction can have on the boundary layer development and turbulent structures in the flow. Detailed two-component laser Doppler velocimetry (LDV) and laser-induced fluorescence (LIF) based measurements have been undertaken in regions close to the suction strip and further downstream. The region close to the strip involves a flow reversal accompanied by a change in sign for the Reynolds shear stress and strong gradients in the flow variables. The mean streamwise velocity after suction remains larger than its corresponding no-suction value. Relative to the no-suction case, the velocity fluctuations first decrease with suction followed by a slow recovery which may involve a slight overshoot. LIF visualizations indicate that compared to the no-suction case, the low-speeds streaks stay closer to the wall and exhibit a smaller amount of spanwise and wall-normal oscillations with suction. The visualization results are consistent with two-point velocity correlation measurements. The streamwise and spanwise correlation measurements indicate that the structures are disrupted or removed from the boundary layer due to suction suggesting that the original boundary layer has been strongly influenced by suction. The results are explained by the development of a new inner layer that forms downstream of the suction strip.     

Vortex reynolds number in turbulent boundary layers

The effects of vortex Reynolds number on the statistics of turbulence in a turbulent boundary layer have been investigated. Vortex Reynolds number is defined as the ratio of circulation around the vortex structure to the fluid viscosity. The vortex structure of the outer region was modeled and a full numerical simulation was then conducted using a high-order spectral method. A unit domain of the outer region of a turbulent boundary layer was assumed to be composed of essentially three elements: a wall, a Blasius mean shear, and an elliptic vortex inclined at 45° to the flow direction. The laminar base-flow Reynolds number is roughly in the same range as that of a turbulent boundary layer based on eddy viscosity, and the vortex-core diameter based on the boundary-layer thickness is nearly the same as the maximum mixing length in a turbulent boundary layer. The computational box size, namely, 500, 150, and 250 wall units in the streamwise, surface-normal, and spanwise directions, respectively, is approximately the same as the measured quasi-periodic spacings of the near-wall turbulence-producing events in a turbulent boundary layer. The effects of vortex Reynolds number and the signs of the circulation on the moments of turbulence were examined. The signs mimic the ejection and sweep types of organized motions of a turbulent boundary layer. A vortex Reynolds number of 200 describes the turbulence moments in the outer layer reasonably well.     

湍流边界层外区相干结构的三维波模型

根据流动稳定性理论,提出了一种三维波模型来描述湍流边界层外区大尺度相干结构。计算所得流线图和等涡量线图较罗纪生,周恒（1993）的二维波模型更符合实验结果。说明该三维模型能够较好地反映湍流边界层外区大尺度相干结构的物理特征。     

Turbulent boundary layer flow with a step change from smooth to rough surface

A direct numerical simulation (DNS) dataset of a turbulent boundary layer (TBL) with a step change from a smooth to a rough surface is analyzed to examine the characteristics of a spatially developing flow. The roughness elements are periodically arranged two-dimensional (2-D) spanwise rods, with the first rod placed 80θ_in downstream from the inlet, where θ_in denotes the inlet momentum thickness. Based on an accurate estimation of relevant parameters, clear evidence for mean flow universality is provided when scaled properly, even for the present roughness configuration, which is believed to have one of the strongest impacts on the flow. Compared to previous studies, it is shown that overshooting behavior is present in the first- and second-order statistics and is locally created either within the cavity or at the leading edge of the roughness depending on the type of statistics and the wall-normal measurement location. Inspection of spatial two-point correlations of the streamwise velocity fluctuations shows a continuous increase of spanwise length scales of structures over the rough wall after the step change at a greater growth rate than that over smooth wall TBL flow. This is expected because spanwise energy spectrum shows presence of much energetic wider structures over the rough wall. Full images of the DNS data are presented to describe not only predominance of hairpin vortices but also a possible spanwise scale growth mechanism via merging over the rough wall.     

Detecting coherent patterns in a flume by using PIV and IR imaging techniques

We investigated the flow field in a turbulent boundary layer in a flume, by using Particle Image Velocimetry (PIV) and Hot-Foil Infrared Imaging (HFIRI) techniques. Coherent patterns in the flow were identified and characterized by using instantaneous velocity and temperature fields. The velocity fields in the streamwise–spanwise plane were measured in parallel to the temperature distribution of the flume bottom. The identified patterns are represented by means of their spatial characteristics – a non-dimensional spatial separation between streamwise patterns, ⁺.     

A vorticity stretching diagnostic for turbulent and transitional flows

Vorticity stretching in wall-bounded turbulent and transitional flows has been investigated by means of a new diagnostic measure, denoted by Γ, designed to pick up regions with large amounts of vorticity stretching. It is based on the maximum vorticity stretching component in every spatial point, thus yielding a three-dimensional scalar field. The measure was applied in four different flows with increasing complexity: (a) the near-wall cycle in an asymptotic suction boundary layer (ASBL), (b) K-type transition in a plane channel flow, (c) fully turbulent channel flow at Re _τ = 180 and (d) a complex turbulent three-dimensional separated flow. Instantaneous data show that the coherent structures associated with intense vorticity stretching in all four cases have the shape of flat ‘pancake’ structures in the vicinity of high-speed streaks, here denoted ‘h-type’ events. The other event found is of ‘l-type’, present on top of an unstable low-speed streak. These events (l-type) are further thought to be associated with the exponential growth of streamwise vorticity in the turbulent near-wall cycle. It was found that the largest occurrence of vorticity stretching in the fully turbulent wall-bounded flows is present at a wall-normal distance of y ⁺?=?6.5, i.e. in the transition between the viscous sublayer and buffer layer. The associated structures have a streamwise length of ~200–300 wall units. In K-type transition, the Γ-measure accurately locates the regions of interest, in particular the formation of high-speed streaks near the wall (h-type) and the appearance of the hairpin vortex (l-type). In the turbulent separated flow, the structures containing large amounts of vorticity stretching increase in size and magnitude in the shear layer upstream of the separation bubble but vanish in the backflow region itself. Overall, the measure proved to be useful in showing growing instabilities before they develop into structures, highlighting the mechanisms creating high shear region on a wall and showing turbulence creation associated with instantaneous separations.     

Direct numerical simulation of a particle-laden flow in a flat plate boundary layer

In this paper, a direct numerical simulation of particle-laden flow in a flat plate boundary layer is performed, using the Eulerian–Lagrangian point-particle approach. This is, as far as we know, the first simulation of a particle-laden spatially-developing turbulent boundary layer with two-way coupling. A local minimum of the particle number density is observed in the close vicinity of the wall. The present simulation results indicate that the inertial particles displace the quasi-streamwise vortices towards the wall, which, in turn, enhance the mean streamwise fluid velocity. As a result, the skin-friction coefficient is increased whereas the boundary layer integral thicknesses are reduced. The presence of particles augments the streamwise fluctuating velocity in the near-wall region but attenuates it in the outer layer. Nevertheless, the wall-normal and spanwise velocity fluctuations are significantly damped, and so is the Reynolds stress. In addition, the combined effect of a reduced energy production and an increased viscous dissipation leads to the attenuation of the turbulent kinetic energy.     

Experimental study on flow control of the turbulent boundary layer with micro-bubbles

The effect of micro-bubbles on the turbulent boundary layer in the channel flow with Reynolds numbers (Re) ranging from \(0.87\times 10 ^{5}\) to \(1.23\times 10^{5}\) is experimentally studied by using particle image velocimetry (PIV) measurements. The micro-bubbles are produced by water electrolysis. The velocity profiles, Reynolds stress and instantaneous structures of the boundary layer, with and without micro-bubbles, are measured and analyzed. The presence of micro-bubbles changes the streamwise mean velocity of the fluid and increases the wall shear stress. The results show that micro-bubbles have two effects, buoyancy and extrusion, which dominate the flow behavior of the mixed fluid in the turbulent boundary layer. The buoyancy effect leads to upward motion that drives the fluid motion in the same direction and, therefore, enhances the turbulence intense of the boundary layer. While for the extrusion effect, the presence of accumulated micro-bubbles pushes the flow structures in the turbulent boundary layer away from the near-wall region. The interaction between these two effects causes the vorticity structures and turbulence activity to be in the region far away from the wall. The buoyancy effect is dominant when the Re is relatively small, while the extrusion effect plays a more important role when Re rises.     

An experimental study into the effects of streamwise and spanwise acceleration in a turbulent boundary layer

We compare two turbulent boundary layers produced in a low-speed water channel experiment. Both are subjected to an identical streamwise pressure gradient generated via a lateral contraction of the channel, and an additional spanwise pressure gradient is imposed on one of the layers by curving the contraction walls. Despite a relatively high streamwise acceleration, hot-film probe measurements of the mean-velocity distributions show that the Reynolds number increases whilst the coefficient of friction decreases downstream. Visualization of the viscous layers using hydrogen bubbles reveal an increase in the non-dimensional streak spacing in response to the acceleration. Changes in statistical moments of the streamwise velocity near the wall suggest an increased dominance of high-velocity fluctuations. The near-wall streaks and velocity statistics have little sensitivity to the boundary layer three-dimensionality induced by the spanwise pressure gradient, with the boundary-layer crossflow velocity reaching 11 % that of the local freestream velocity.     

DNS of a spatially developing turbulent boundary layer with passive scalar transport

A direct numerical simulation (DNS) of a spatially developing turbulent boundary layer over a flat plate under zero pressure gradient (ZPG) has been carried out. The evolution of several passive scalars with both isoscalar and isoflux wall boundary condition are computed during the simulation. The Navier–Stokes equations as well as the scalar transport equation are solved using a fully spectral method. The highest Reynolds number based on the free-stream velocity U_∞ and momentum thickness θ is Re_θ=830, and the molecular Prandtl numbers are 0.2, 0.71 and 2. To the authors’ knowledge, this Reynolds number is to date the highest with such a variety of scalars. A large number of turbulence statistics for both flow and scalar fields are obtained and compared when possible to existing experimental and numerical simulations at comparable Reynolds number. The main focus of the present paper is on the statistical behaviour of the scalars in the outer region of the boundary layer, distinctly different from the channel-flow simulations. Agreements as well as discrepancies are discussed while the influence of the molecular Prandtl number and wall boundary conditions is also highlighted. A Pr scaling for various quantities is proposed in outer scalings. In addition, spanwise two-point correlation and instantaneous fields are employed to investigate the near-wall streak spacing and the coherence between the velocity and the scalar fields. Probability density functions (PDF) and joint probability density functions (JPDF) are shown to identify the intermittency both near the wall and in the outer region of the boundary layer. The present simulation data will be available online for the research community.     

Observations of meandering superstructures in the roughness sublayer of a turbulent boundary layer

The existence of meandering superstructures in a turbulent boundary layer overlying irregular roughness is explored with high-frame-rate particle-image velocimetry measurements within the roughness sublayer at moderate Reynolds number. Elongated streamwise fields of view reconstructed from this data using a Taylor’s hypothesis approach revealed spanwise-meandering regions of low-streamwise-momentum fluid that extended several boundary-layer thicknesses in the streamwise direction. Such signatures are consistent with previous observations of superstructures in smooth-wall turbulence. Counter-rotating wall-normal vortex cores were found to reside along the spanwise boundaries of these superstructure patterns, consistent with the spatial characteristics of hairpin vortex packets.