氢化物—石墨炉原子吸收光谱法的进展

本文评述了氢化物－石墨炉原子吸收光谱的新进展。内容包括发展沿革、氢化物输入石墨炉方式、氢化物分解和沉积、原子化机理、干扰和应用等部分。指出同时把石墨炉作为氢化物沉积和原子化的工具这种新的联合方式，是近年来氢化物原子吸收法的引人注目的进展，将会获得进一步的发展和应用。本法的主要优点是气相和液相干扰很少。参考文献25篇。     

ICP／AES操作条件及氢化物发生条件对As,Se和Ge光谱信号影响的…

本文较系统地研究了ＩＣＰ／ＡＥＳ操作条件及酸介质。ＨａＢＨ４溶液溶度对Ａｓ，Ｓｅ和Ｇｅ谱线强度以及信背比的影响，讨论了这些元素的最佳检测条件，考察了一些共存元素对氢化物光谱信号的影响，观察到Ａｓ，Ｓｅ和Ｇｅ氢化物发生中Ｇｅ的光谱信号的一些特殊行为，及Ｃｕ对Ｇｅ的氢化物光谱信号的增强。     

氢化物发生法测定铅的进展

本文对铅的氢化物发生法的反应体系及机理，氢化物发生方式及检测手段，干扰及其消除，形态分析等诸方面进行评述。     

氢化物—石墨炉原位富集原子吸收光谱法测定痕量锑

本文对标示问题进行了研究，自行设计了氢化物发生器，采用以石墨炉两端输入氢化物方式，载气流向用活塞控制，大幅度减少原子化阶段石墨炉内氢气分压，提高了锑的灵敏度，对氢化锑的石墨炉表面分解沉积和原子化机理进行了讨论，方法有于矿泉水和自来水痕量锑的测定，结果令人满意，锑的特征浓度为３０ｐｇ／０．００４４Ａ。     

断续流动氢化物发生法在AAS／AFS中的应用

本文介绍了一种介于流动注射法及连续流动法之间的氢化物发生进样技术。这种技术被称为断续流动法。它具有装置简单，灵活性大，运转成本低等特点。目前，已成功地应用于氢化物原子吸收法及氢化物原子荧光法中。     

ICP／AES操作条件及氢化物发生条件对As、Se和Ge光谱信号影响的研究

本文较系统地研究了ＩＣＰ／ＡＥＳ操作条件及酸介质。ＮａＢＨ４溶液浓度对Ａｓ、Ｓｅ和Ｇｅ谱线强度以及信背比的影响，讨论了这些元素的最佳检测条件，考察了一些共存元素对氢化物光谱信号的影响，观察到Ａｓ、Ｓｅ和Ｇｅ氢化物发生中Ｇｅ的光谱信号的一些特殊行为，及Ｃｕ对Ｇｅ的氢化物光谱信号的增强。     

高压下氢基高温超导体研究的新进展

富氢材料被认为是室温超导体的最佳候选体系,是物理学、材料科学等多学科的热点研究领域之一。理论和实验研究发现的新型共价氢化物H3S和笼状氢化物LaH10的超导转变温度(T_c)均超过200 K,进一步推动了对富氢化合物超导电性的探索。最近,通过高压实验合成的碳质硫氢化物在288 K的室温下实现了零电阻,让人们看到了室温超导的曙光。本文结合课题组在此领域的主要成果,介绍了3类典型富氢化合物的结构及超导特性,包括近期首次在层状氢化物中发现的具有类五角石墨烯结构的富氢超导体HfH₁₀,其超导转变温度高达213~234 K。     

氢化物—原子荧光法测定植物及人发中的痕量硒

本文研究开发了在捕集剂覆盖下低温焙烧富集分离氢化物原子荧光光谱法测定植物和人发样品中的痕量硒，本方法克服了使用混合酸分解样品时，有机物质不能彻底分解而给测定带来的不利影响。其方法精密度和准确度均能满足测定的要求。     

自制氢化物发生器原子吸收光谱法测定微量样品中Bi的含量

氢化物原子吸收光谱法能对多种元素进行痕量级的测定，但存在着不足之处，为此，我们设计并自制了简易的氢化物发生器，制做简单，操作方便，消耗样品少，而精密度灵敏度，检出限等指标均能满足测定要求。     

ICP-AES氢化物发生法测定生物样品中的痕量硒

本文研究了ICP-AES氢化物发生法测定生物样品中痕量硒的方法。对氢化物发生条件和样品消化过程进行了选择,并使之达最佳化。方法检出限达0.09ng/ml。     

Exploding wires in air and vacuum

An apparatus for studies of wire explosions in air at atmospheric as well as reduced pressures is described. A theoretical treatment of the discharge circuit is presented. In this treatment the external resistance and inductance as well as the wire inductance (all as functions of time) have been taken into consideration. It is then possible to calculate the wire variables — current, resistance, resistive voltage drop, effect, and energy input — as functions of time from thedI/dt waveform experimentally obtained. Wire variables of Ni- and W-wires exploded both in air and vacuum are presented as well as a discussion of these.     

Multivariate analysis of dynamical processes

The analysis of multi-dimensional biomedical systems requires analysis techniques, which are able to deal with multivariate data consisting of both time series as well as point processes. Univariate and bivariate analysis techniques in the frequency domain for time series and point processes are established and investigated, although the number of investigations is strongly biased towards time series. Actual multivariate techniques for time series or hybrids of time series and point processes are scarcely addressed. Here, we present spectral analysis techniques which are able to analyse point processes as well as time series. Thereby, univariate, bivariate as well as multivariate techniques are discussed. Applications to simulated as well as real-world data reveal the abilities of the proposed techniques.     

Optical and electro-catalytic properties of bundled ZnO nanowires grown on a ITO substrate

Bundled wurtzite zinc oxide (ZnO) nanowires were fabricated in a facile manner on an ITO-conducting substrate via a microemulsion route without using any hard template or external electric/magnetic field. Structure and properties of the as-prepared ZnO electrode were investigated using scanning electron microscopy, X-ray diffraction, photoluminescence, Raman spectroscopy, as well as electrochemical tests. The ZnO electrode shows excellent optical and electrocatalytic ability, which may find further applications such as optoelectronics or as sensors as well as other modern industrial areas.     

Multiple pure tone noise prediction

This paper presents a fully numerical method for predicting multiple pure tones, also known as “Buzzsaw” noise. It consists of three steps that account for noise source generation, nonlinear acoustic propagation with hard as well as lined walls inside the nacelle, and linear acoustic propagation outside the engine. Noise generation is modeled by steady, part-annulus computational fluid dynamics (CFD) simulations. A linear superposition algorithm is used to construct full-annulus shock/pressure pattern just upstream of the fan from part-annulus CFD results. Nonlinear wave propagation is carried out inside the duct using a pseudo-two-dimensional solution of Burgers? equation. Scattering from nacelle lip as well as radiation to farfield is performed using the commercial solver ACTRAN/TM. The proposed prediction process is verified by comparing against full-annulus CFD simulations as well as against static engine test data for a typical high bypass ratio aircraft engine with hardwall as well as lined inlets. Comparisons are drawn against nacelle unsteady pressure transducer measurements at two axial locations as well as against near- and far-field microphone array measurements outside the duct.     

The pathogenesis of Randall's plaque: a papilla cartography of Ca compounds through an ex vivo investigation based on XANES spectroscopy

At the surface of attached kidney stones, a particular deposit termed Randall's plaque (RP) serves as a nucleus. This structural particularity as well as other major public health problems such as diabetes type‐2 may explain the dramatic increase in urolithiasis now affecting up to 20% of the population in the industrialized countries. Regarding the chemical composition, even if other phosphate phases such as whitlockite or brushite can be found as minor components (less than 5%), calcium phosphate apatite as well as amorphous carbonated calcium phosphate (ACCP) are the major components of most RPs. Through X‐ray absorption spectroscopy performed at the Ca K‐absorption edge, a technique specific to synchrotron radiation, the presence and crystallinity of the Ca phosphate phases present in RP were determined ex vivo. The sensitivity of the technique was used as well as the fact that the measurements can be performed directly on the papilla. The sample was stored in formol. Moreover, a first mapping of the chemical phase from the top of the papilla to the deep medulla is obtained. Direct structural evidence of the presence of ACCP as a major constituent is given for the first time. This set of data, coherent with previous studies, shows that this chemical phase can be considered as one precursor in the genesis of RP.     

Femtosecond self mode locking of Yb:fluoride phosphate glass laser

Passive cw mode locking of an ytterbium-doped fluoride phosphate glass laser is demonstrated, for what we believe to be the first time, based solely on the Kerr effect in the active medium in a resonator with dispersion compensation. Nearly bandwidth-limited pulses as short as 160fs are generated at ~1040 nm. We obtain average output powers as high as 250mW at 170-MHz repetition rate with absorbed pump power as low as 1.2W.     

Simulating feedback and reversibility in substrate-enzyme reactions

We extend discrete event models (DEM) of substrate-enzyme reactions to include regulatory feedback and reversible reactions. Steady state as well as transient systems are modeled and validated against ordinary differential equation (ODE) models. The approach is exemplified in a model of the first steps of glycolysis with the most common regulatory mechanisms. We find that in glycolysis, feedback and reversibility together act as a significant damper on the stochastic variations of the intermediate products as well as for the stochastic variation of the transit times. This suggests that these feedbacks have evolved to control both the overall rate of, as well as stochastic fluctuations in, glycolysis.     

Continuing Studies of Plasma Erosion Switches for Power Conditioning on Multiterawatt Pulsed Power Accelerators

Recent PITHON experiments with plasma erosion switches (PES) have extended the range of operation of the switches by about 50 percent, in terms of closed time and charge passing through the switch. The quantity of charge passed through the switch has been increased to as much as 35 mC. Currents as large as 1 MA and voltages as great as 1.8 MV have been switched off to be diverted to a downstream load. The impedance of the erosion switch can be described as having three stages: 1) essentially zero impedance, 2) a transitional opening phase, and 3) an impedance which is very large (greater than 5 ?) in comparson with the subohm downstream load. Current diagnostics, consisting of Rogowski coils and segmented shunts, have been successfully developed to monitor the current which propagates to the load region. These monitors have measured rise times as short as 38 ns and slew rates as great as 1014 A/s at the load. With wire array loads, the pulse conditioning of the switch has been observed to reduce the magnitude of the current losses in the feed which are present when no switch is used. Correlations have been made between the switch closed time, voltage, current, and power with the feed inductance and the generator power injected into the magnetic insulated transmission line (MITL).     

500 kV全固态Marx发生器

500 kV全固态Marx发生器采用Z型电路结构,以28个最大工作电压达22 kV、满载最高连续重复运行频率达200 Hz的绝缘栅双极型晶体管组件作为脉冲控制开关,采用以金属化膜电容器和线绕电感构成的梯形脉冲形成网络作为储能和脉冲形成器件。目前已实现500 kV脉冲输出,在50 Hz的重复频率下实现数十个脉冲的猝发输出。该发生器的输出脉冲电压峰值与已有文献报道的最高功率固态Marx发生器技术指标相近,输出脉冲电流峰值提高1倍,达到1000 A,发生器输出脉冲功率峰值达到500 MW。在采用电容器作为储能元件时,此Marx发生器输出脉冲宽度可在3～10 s范围内连续调整。     

液体-液体相变与反常特性

绝大多数物质的液态密度随温度降低而增大,即常见的热胀冷缩现象.但存在一类物质,如水及第四主族的硅、锗等,其液态密度在一定温度范围内随温度的升高而增大,即密度反常现象.此外,该类物质还存在动力学反常(密度越大粒子运动越快)、热力学反常(热力学量的涨落随温度降低而升高)等其他反常特性.这类材料的化学性质千差万别,但却具有相似的物理反常特性.进一步的理论研究发现部分材料具有两种液态,即高密度液态和低密度液态,两者之间存在一级相变.因此,反常特性与液体-液体相变是否有直接关联是一个值得深入研究的课题.本文主要介绍了具有液体-液体相变的一类材料及其反常特性,包括高温高压下氢的液体-液体相变及其超临界现象,镓的反常特性及其与液体-液体相变的关联等.