NR–EPDM covulcanization: A novel approach

Bis(diisopropyl)thiophosphoryl disulfide (DIPDIS) was used successfully as a novel coupling agent cum accelerator to co‐vulcanize the elastomer blend comprising highly unsaturated natural rubber (NR) and ethylene propylene diene rubber (EPDM) of low unsaturation content. The blend vulcanizates produced exhibit improved physical properties that can be further enhanced by implementing a two‐stage vulcanization technique, as well as by judicious selection of the NR‐to‐EPDM ratio. The results indicate coherency and homogeneity in the blend composition of two‐stage vulcanizates. The cure‐rate mismatch problem could thus be solved through the formation of rubber‐bound intermediates with a multifunctional rubber additive (i.e., DIPDIS), thereby restricting the curative migration from lower to highly unsaturated rubber. The blend morphology as revealed by SEM studies accounts for significant improvement in physical properties, particularly in two‐stage vulcanizates. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 800–808, 2001     

Effect of bis(diisopropyl)thiophosphoryl disulfide on the covulcanization of styrene–butadiene rubber and ethylene–propylene–diene (monomer) blends

Covulcanization of elastomer blends constituting styrene–butadiene rubber (SBR) and ethylene–propylene–diene (monomer) rubber (EPDM) was successfully performed in the presence of reinforcing fillers like carbon black and silica by using a multifunctional rubber additive, bis(diisopropyl)thiophosphoryl disulfide (DIPDIS). The polarity of EPDM rubber was increased by a two‐stage vulcanization technique, which allowed the formation of rubber‐bound intermediates. In this way the migration of both curatives and reinforcing fillers in the EPDM–SBR blend could be controlled and cure rate mismatch could be minimized. The process significantly improved the physical properties of the blend vulcanizates. The phase morphology, as evident from the SEM micrographs, was indicative of the presence of a much more compact and coherent rubber matrix in the two‐stage vulcanizates. Different accelerator systems were studied to understand better the function and effectiveness of DIPDIS in developing homogeneity in the blends of dissimilar elastomers. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1231–1242, 2004     

Novel method for preparation of carboxylated nitrile rubber–natural rubber blends using bis(diisopropyl)thiophosphoryl polysulfides

Bis(diisopropyl)thiophosphoryl trisulfide (DIPTRI) and bis(diisopropyl)thiophosphoryl tetrasulfide (DIPTET) are successfully used as a novel coupling agent and accelerator, respectively, to covulcanize an elastomer blend comprising polar carboxylated nitrile rubber (XNBR) and nonpolar natural rubber (NR). These compounds are capable of forming a chemical link between these dissimilar rubbers to produce a technologically compatible blend as judged by a swelling experiment. The blend vulcanizates thus produced exhibit enhanced physical properties that can further be improved by adopting the two‐stage vulcanization technique and also by judicious selection of the NR:XNBR ratio. The blend morphology assessed by scanning electron microcroscopy micrographs accounts for significant improvement in the physical properties of the blend vulcanizates, particularly in two‐stage vulcanization. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1725–1736, 2001     

Effect of dynamic crosslinking on impact strength and other mechanical properties of polypropylene/ethylene‐propylene‐diene rubber blends

The deformation and fracture behavior of several dynamic vulcanizate blends of isotactic polypropylene with ethylene‐propylene‐diene rubber (EPDM) was examined and compared with those of uncrosslinked blends of PP/EPDM. These blends were prepared by melt mixing in an internal mixer at 190°C in a composition range of 10–40 wt % EPDM rubber. The variation in yield stress, the strength of fibrils of the craze, and the number density of the EPDM rubber domains (morphology fixation) that are dominant factors for enhancing interfacial adhesion and toughness in dynamic vulcanizate blends were evaluated. The ductility and toughness of these materials were explained in light of the composition between crack formation and the degree of plastic deformation through crazing and shear yielding. The physicomechanical properties including the hardness, yield stress, Young's modulus, percentage elongation, impact strength, flexural strength, and flexural modulus of dynamic vulcanized blends were found to be consistent and displayed higher values compared with uncrosslinked blends. The nucleation effect of the crosslinked particles and the decrease of crystallinity of the EPDM rubber were also considered to contribute to the improvement in the impact strength. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2089–2103, 2000     

Compatibilization of nitrile‐butadiene rubber/ethylene‐propylene‐diene monomer blends by mercapto‐modified ethylene‐vinyl acetate copolymers

Mercapto‐modified ethylene‐vinyl acetate (EVASH) has been employed as a reactive compatibilizing agent for nitrile‐butadiene rubber (NBR)/ethylene‐propylene‐diene monomer (EPDM) blends vulcanized with a sulfur/2,2′‐dithiobisbenzothiazole (MBTS) single accelerator system and a (sulfur/MBTS/tetramethylthiuram disulfide (TMTD) binary accelerator system. The addition of 5.0 phr EVASH resulted in a significant improvement in the tensile properties of blends vulcanized with the sulfur/MBTS system. In addition to better mechanical performance, these functionalized copolymers gave rise to a more homogeneous morphology and, in some cases, better aging resistance. The compatibilization was not efficient in blends vulcanized with the S/MBTS/TMTD binary system, probably because of the faster vulcanization process occurring in this system. The good performance of these EVASH samples as compatibilizing agents for NBR/EPDM blends is attributed to the higher polarity of these components that is associated with their lower viscosity. Dynamic mechanical analysis also suggested a good interaction between the phases in the presence of EVASH. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1404–1412, 2004     

Mechanical property and morphology comparison between the two blends poly(propylene)/ethylene‐propylene‐diene monomer elastomer and poly(propylene)/maleic anhydride‐g‐ethylene‐propylene‐diene monomer

The comparison of the mechanical properties between poly(propylene)/ethylene‐propylene‐diene monomer elastomer (PP/EPDM) and poly(propylene)/maleic anhydride‐g‐ethylene‐propylene‐diene monomer [PP/MEPDM (MAH‐g‐EPDM)] showed that the latter blend has noticeably higher Izod impact strength but lower Young's modulus than the former one. Phase morphology of the two blends was examined by dynamic mechanical thermal analysis, indicating that the miscibility of PP/MEPDM was inferior to PP/EPDM. The poor miscibility of PP/MEPDM degrades the nucleation effectiveness of the elastomer on PP. The observations of the impact fracture mode of the two blends and the dispersion state of the elastomers, determined by scanning electron microscopy, showed that PP/EPDM fractured in a brittle mode, whereas PP/MEPDM in a ductile one, and that a finer dispersion of MEPDM was found in the blend PP/MEPDM. These observations indicate that the difference in the dispersion state of elastomer between PP/EPDM and PP/MEPDM results in different fracture modes, and thereby affects the toughness of the two blends. The finer dispersion of MEPDM in the blend of PP/MEPDM was attributed to the part cross‐linking of MEPDM resulting from the grafting reaction of EPDM with maleic anhydride (MAH) in the presence of dicumyl peroxide (DCP). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2486–2491, 2002     

Miscibility of blends of ethylene‐propylene‐diene terpolymer and polypropylene

The miscibility of polymers is not only an important basis for selecting a proper blending method, but it is also one of the key factors in determining the morphology and properties of the blends. The miscibility between ethylene‐propylene‐diene terpolymer (EPDM) and polypropylene (PP) was explored by means of dynamic mechanical thermal analysis, transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The results showed that a decrease in the PP content and an increase of the crosslinking density of EPDM in the EPDM/PP blends caused the glass‐transition temperature peaks of EPDM to shift from a lower temperature to higher one, yet there was almost no variance in the glass‐transition temperature peaks of PP and the degree of crystallinity of PP decreased. It was observed that the blends prepared with different mixing equipment, such as a single‐screw extruder and an open mill, had different mechanical properties and blends prepared with the former had better mechanical properties than those prepared with the latter. The TEM micrographs revealed that the blends were composed of two phases: a bright, light PP phase and a dark EPDM phase. As the crosslinking degree of EPDM increased, the interface between the phases of EPDM and PP was less defined and the EPDM gradually dispersed in the PP phase became a continuous phase. The results indicated that EPDM and PP were both partially miscible. The mechanical properties of the blends had a lot to do with the blend morphology and the miscibility between the blend components. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 315–322, 2002     

Effect of anhydride‐modified ethylene–propylene–diene rubber and ethylene–vinyl acetate copolymers on the compatibilization of nitrile rubber/ethylene–propylene–diene rubber blends

The effects of maleic anhydride modified ethylene–propylene–diene rubber (EPDMMA) and maleic anhydride modified ethylene–vinyl acetate (EVAMA) on the compatibilization of nitrile rubber (NBR)/ethylene–propylene–diene rubber (70:30 w/w) blends vulcanized with a sulfur system were investigated. The presence of EPDMMA and EVAMA resulted in improvements of the tensile properties, whereas no substantial change was detected in the degree of crosslinking. The blend systems were also analyzed with scanning electron microscopy and dynamic mechanical thermal analysis. The presence of EVAMA resulted in a blend with a more homogeneous morphology. The compatibilizing effect of this functional copolymer was also detected with dynamic mechanical analysis. A shift of the glass‐transition temperature of the NBR phase toward lower values was observed. The presence of EPDMMA and EVAMA also increased the thermal stability, as indicated by an improvement in the retention of the mechanical properties after aging in an air‐circulating oven. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2408–2414, 2003     

Using fish scales (Sardina pilchardus) within ethylene‐propylene‐diene ter monomer rubber as bio‐based filler

Proper management of waste bio‐based materials is an important subject to protect the environment in a sustainable manner. In this study, ethylene‐propylene‐diene monomer (EPDM) composites with different fish scale content were prepared and properties of these composites were investigated. Mechanical tests, gel content, curing, and thermal properties were analyzed. In addition, rheological and morphological analyses were also carried out. It was seen that EPDM rubber and fish scale composite have a good compatibility. The addition of fish scale improved the mechanical properties of the final material. Moreover, an increase in gel content and in swelling ratio was obtained for the composite samples containing fish scale. Moving die rheometer tests are concluded that fish scale has acted like an agent that improves the vulcanization process. Thermal gravimetric analysis result pointed out that the thermal stability of the composite developed is higher than neat EPDM. It was concluded that 40 phr fish scale content gives best results. The kinetic study demonstrated that fish scale is compatible with the matrix and improves the vulcanization process. The results have shown that using the fish scale as a bio‐based filler is a facile and green way to accommodate the bio‐based wastes. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46698.     

A comparison of white rice husk ash and silica as fillers in ethylene–propylene–diene terpolymer vulcanizates

White rice husk ash (WRHA) and silica filled ethylene–propylene–diene terpolymer (EPDM) vulcanizates were prepared using a laboratory size two‐roll mill. Curing characteristics and physical properties of vulcanizates were studied with respect to the filler loading and filler type. Filler loading was varied from 0–50 parts per hundred resin (phr) at 10 phr intervals. Curing was carried out using a semi‐efficient vulcanization system in a Monsanto rheometer. Enhancement of the curing rate was observed with increasing WRHA loading, whereas the opposite trend was observed for silica‐filled vulcanizates. It was also indicated by the maximum torque and Mooney viscosity results that WRHA offers processing advantages over silica. Compared to the silica‐filled vulcanizates, the effect of filler loading on the physical properties of WRHA‐filled vulcanizates was not significant. According to these observations, WRHA could be used as a diluent filler for EPDM rubber, while silica can be used as a reinforcing filler. © 2001 Society of Chemical Industry     

Synthesis and evaluation of high‐performance ethylene–propylene–diene terpolymer/organoclay nanoscale composites

The main objective of this study was to synthesize and characterize the properties of ethylene–propylene–diene terpolymer (EPDM)/clay nanocomposites. Pristine clay, sodium montmorillonite (Na⁺–MMT), was intercalated with hexadecyl ammonium ion to form modified organoclay (16Me–MMT) and the effect of intercalation toward the change in interlayer spacing of the silicate layers was studied by X‐ray diffraction, which showed that the increase in interlayer spacing in Na⁺–MMT by 0.61 nm is attributed to the intercalation of hexadecyl ammonium ion within the clay layers. In the case of EPDM/16Me–MMT nanocomposites, the basal reflection peak was shifted toward a higher angle. However, gallery height remained more or less the same for different EPDM nanocomposites with organoclay content up to 8 wt %. The nanostructure of EPDM/clay composites was characterized by transmission electron microscopy, which established the coexistence of intercalated and exfoliated clay layers with an average layer thickness in the nanometer range within the EPDM matrix. The significant improvement in thermal stability and mechanical properties reflects the high‐performance nanocomposite formation. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2429–2436, 2004     

New synthesis methods for polypropylene‐co‐ethylene‐propylene rubber

In this research, the reinforcement of polypropylene (PP) was studied using a new method that is more practical for synthesizing polypropylene‐block‐poly(ethylene‐propylene) copolymer (PP‐co‐EP), which can be used as a rubber toughening agent. This copolymer (PP‐co‐EP) could be synthesized by varying the feed condition and changing the feed gas in the batch reactor system using Ziegler–Natta catalysts system at a copolymerization temperature of 10°C. The ¹³C‐NMR tested by a 21.61‐ppm resonance peak indicated the incorporation of ethylene to propylene chains that could build up the microstructure of the block copolymer chain. Differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and dynamic mechanical analysis (DMA) results also confirmed these conclusions. Under these conditions, the morphology of copolymer trapped in PP matrix could be observed and the copolymer T_g would decrease when the amount of PP‐co‐EP was increased. DMA study also showed that PP‐co‐EP is good for the polypropylene reinforcement at low temperature. Moreover, the PP‐co‐EP content has an effect on the crystallinity and morphology of polymer blend, i.e., the crystallinity of polymer decreased when the PP‐co‐EP content increased, but tougher mechanical properties at low temperature were observed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3609–3616, 2007     

Self‐reinforcing elastomer composites based on ethylene–propylene–diene monomer rubber and liquid‐crystalline polymer

In this study, the prime factor determining the size, shape, and distribution of liquid‐crystalline polymer (LCP) was the viscosity ratio at the processing conditions. The fiber‐forming capacity of the LCP depended on the viscosity of the ethylene–propylene–diene monomer rubber (EPDM). With increasing LCP content, the tensile and tear strengths did not increase, perhaps because of incompatibility between the EPDM and LCP. The hardness increased because of the hard mesogenic groups in the LCP. The percentage swelling decreased as the LCP content increased. With increasing LCP content, processability became easier because of a lower melt viscosity. The scorch time increased at higher LCP levels. A higher percentage crystallinity was observed with increasing LCP content. Scanning electron microscopy clearly showed the fiber phase formation, which was two‐dimensionally isotropic in nature, confirming fiber formation even in a shear field. The addition of LCP improved the thermal stability. The onset degradation temperatures shifted to higher values with increasing LCP content. Dynamic mechanical thermal analysis revealed that with the addition of LCP, the mechanical damping increased at its lower level. High‐temperature processing increased the effective amorphous zone. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 711–718, 2004     

Structural characterization of reactor blends of polypropylene and ethylene‐propylene rubber

Blends of isotactic polypropylene (PP), ethylene‐propylene rubber copolymer (EPR), and ethylene‐propylene crystalline copolymer (EPC) can be produced through in situ polymerization processes directly in the reactor and blends with different structure and composition can be obtained. In this work we studied the structure of five reactor‐made blends of PP, EPR, and EPC produced by a Ziegler‐Natta catalyst system. The composition of EPR was related to the ratio between ethylene and propylene used in the copolymerization step. The ethylene content in the EPR was in the range of 50–70 mol %. The crystallization behavior of PP and EPC in the blends was influenced by the presence of the rubber, and some specific interactions between the components could be established. By preparative temperature rising elution fractionation (P‐TREF) analysis, the isolation and characterization of crystalline EPC fractions were made. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2155–2162, 2004     

Structure and mechanical properties of nanodispersed fibrous silicate‐reinforced ethylene–propylene–diene monomer nanocomposites

In this study, ethylene–propylene–diene monomer (EPDM)/fibrillar silicate (FS) nanocomposites were successfully prepared by mechanically blending EPDM with FS, which was modified by silane coupling agent KH570 containing methacryloxy group. The effects of silane content and modified FS on the dispersion of FS and mechanical properties of the composites were investigated. The impact of water in FS on mechanical properties of the composites was also evaluated. The results showed that modified FS could be dissociated into nanofibers dispersing evenly in the EPDM matrix by increasing substantially the loading of silane through the mechanical blending. The optimum loading level of silane coupling agent was up to 24 phr/100 phr FS. Silane KH570 could improve the dispersion of FS and strengthen nanofibers–rubber interfacial adhesion even at the loading of as high as 50 phr FS, making FS to exhibit excellent reinforcement to EPDM. Too much FS could not be completely dissociated into nanofibers, slowing down further improvement. The EPDM/FS composites exhibited the similar stress–strain behavior and obvious mechanical anisotropy with short microfiber‐reinforced rubber composites. With the increase in silane coupling agent and modified FS, the number of nanofibers increased because of the exfoliation of FS microparticles; thus, the mechanical behaviors would become more obvious. It was suggested that the free water in FS should be removed before mechanically blending EPDM with FS because it obviously affected the tensile properties of the composites. Regardless of whether FS was dried or modified, the EPDM/FS composites changed little in tensile strength after soaked in hot water. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Tensile elongation of high‐fluid polypropylene/ethylene–propylene rubber blends: Dependence on molecular weight of the components and propylene content of the rubber

We studied tensile behavior of low‐molecular‐weight (MW) polypropylene (PP)/ethylene–propylene rubber (EPR; 70/30) blends from the viewpoint of the MWs of PP and EPR and the compatibility between PP and EPR. The value of the melt flow rate of PP varied from 30 to 700 g/10 min at 230°C. We studied the compatibility between PP and EPR by varying the propylene content in EPR (27 and 68 wt %). At the initial elongation stage, crazes were observed in all blends. When blends included EPR with 27 wt % propylene, the elongation at break of the low‐MW PP improved little. The blends with EPR and 68 wt % propylene content were elongated further beyond their yielding points. The elongation to rupture was increased with increasing MW of EPR. Molecular orientation of the low‐MW PP was manifested by IR dichroism measurements and X‐ray diffraction patterns. The blends of low‐MW PP and EPR could be elongated by the partial dissolution of EPR of high‐MW in the PP amorphous phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 46–56, 2002     

Relaxation of stress in polypropylene and ethylene–propylene–diene elastomer blend vulcanizates at moderate and high extensions

Measurements were made of the relaxation of the stress of stretched polypropylene (PP) and ethylene–propylene–diene elastomer blend vulcanizates at various strain levels. It was found that PP-blended vulcanizates showed greater relaxation than that of the gum vulcanizate at all extensions. There was a continual increase in the relaxation rate with the 10% PP-blended vulcanizate but an initial sharp decrease and then a flattening tendency with the above 10% PP-blended vulcanizate at an increasing stain level. An interesting observation of the study was that the rate of stress relaxation decreased linearly in two steps in the case of blend vulcanizates above 10% PP at 100% and above strain levels. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 2155–2162, 1998     

Flow‐injection polymer analysis of ethylene propylene diene monomer elastomers. I

A rapid, flow‐injection polymer analysis (FIPA) method for the solution characterization of EPDM elastomers, with a wide range of ethylene comonomer content, was developed. Solutions of the polymer were introduced into a flowing mobile phase which was monitored by an array of three detectors: a right‐angle laser light‐scattering unit, a differential refractive index detector, and a differential pressure viscometer. To adequately characterize a wide range of comonomer composition, it was found that a nominal temperature of 90°C and a solvent (e.g., 1,2,4‐trichlorobenzene) capable of high‐temperature sample dissolution was needed for the analysis. Polymer association or aggregation was observed in cyclohexane at lower analysis temperatures. With an analysis time of a few minutes, information on molecular weight, molecular size, and comonomer composition can be obtained directly. Information regarding polydispersity and properties such as melt viscosity may be obtained indirectly or through correlation to other, independent property measurements. The data were also compared to a high‐temperature GPC analysis method already in use. The combination of rapid analysis time and measurement of fundamental molecular properties suggests the usefulness of the instrumentation and method to plant process control. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2178–2189, 2002     

Modification of fast-cure ethylene–propylene diene terpolymer rubber by maleic anhydride and effect of electron donor

Grafting of maleic anhydride (MA) onto fast-cure ethylene–propylene diene terpolymer rubber was studied. The effect of the amount of the MA, initiator (dicumyl peroxide), and electron donor (stearamide) on graft content are described. The potentiometric method and Fourier transform infrared spectroscopy are used to obtained the graft content. The stearamide suppresses the side reactions, such as crosslinking and chain scission. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1–5, 1998