Ni3Al（Z）合金室温拉伸性能及Zr韧化机制的探讨

热处理温度显著影响Ni3Al(Zr)合金的显微组织和室温力学性能。本实验采用SEM，TEM，AES等手段对轧制处理后的试样进行了研究。随着热处理温度升高，再结晶体积百分数增加，再结晶晶粒尺寸增大，室温拉伸强度降低。但室温拉伸塑性随热处理温度升高而增加，在850℃热处理时达到最大值，然后随热处理温度升高而显著降低。俄歇能谱(AES)研究表明Zr在850℃热处理时的晶界偏聚量明显高于1100℃热处理时的偏聚量，说明Zr在室温的塑化作用与其在晶界的分布有关。     

Zr,Cr和B对Ni3Al合金组织和力学性能的影响

本文研究了含Zr(0—0.6at.-％),Cr(0—7.7at.-％)和B(0—2.22at.-％)的Ni_3Al合金的组织和室温至1050℃拉伸性能。结果表明,Ni_3Al合金的屈服强度随温度升高而增加,表现出反常的温度关系。到达峰值后,随温度升高,屈服强度降低。Zr和Zr+Cr在整个试验温度范围都增加Ni_3Al合金的屈服强度,并改善高温抗张强度和塑性。硼增加Ni_3Al合金的抗张强度和屈服强度,同时改善塑性。但当硼含量超过1.37at.-％时,则降低强度和塑性。当硼含量超过溶解度极限时,Ni_3Al合金中形成岛状和球状的Ni_(20)Al_3B_6和Ni_3Al的共晶组织,对强度和塑性都是有害的。     

再结晶Ni3Al(Zr)合金的环境脆性

研究了不同程度再结晶的Ni3Al(Zr)合金在真空和空气中的室温拉伸性能．结果表明，随着再结晶程度的增加，合金的塑性先增加后降低，不完全再结晶的样品表现出良好的拉伸塑性．合金的环境敏感指数随再结晶程度的增加而增加，完全再结晶的样品表现出强烈的环境敏感性．真空和空气中拉伸断口形貌的变化与力学性能变化趋势一致，再结晶程度低的样品的断口形貌为穿晶解理断裂，气氛对其几乎没有影响，而对再结晶程度高和完全再结晶的样品，空气使其沿晶断裂模式倾向增加．     

Ce和Zr复合添加对Al-Cu-Li合金拉伸性能的影响

通过组织分析和常温拉伸性能测试,研究了Ce、Zr复合添加对Al-4. 6Cu-0. 9Li合金组织与拉伸性能的影响。结果表明,微量Ce、Zr复合添加有利于阻止Al-Cu-Li合金再结晶以及较大幅度的细化合金晶粒组织(由70μm至20μm);微量Ce、Zr复合添加虽然不改变Al-Cu-Li合金的时效析出序列,但在提高合金整体强度的同时,进一步提高了合金的塑性。分析表明,合金强度的提高主要归因于微量Ce、Zr复合添加引入的Al_3Zr弥散强化作用,而细化的晶粒和残留相Al Cu Ce Zr粒子尺寸则促进了合金塑性的整体提高。     

球头压痕确定薄膜模量的等效膜厚法

针对名义成分为Ti-46Al-3.8(V,Cr,Ni) (at％)的挤压TiA1合金,研究了热处理工艺对高温时β相含量、形貌的影响,利用高温时β相对α相晶粒的钉扎作用获得了层片团尺寸均匀、细小的全层片组织,测试了具有该组织合金的拉伸性能.结果表明,在1320～1370℃范围内,随保温温度的升高,β相含量逐渐增加,使得合金的晶粒尺寸逐渐减小.实验合金经1340℃/5 min/AC热处理后可以获得层片团(尺寸平均为65 μm),B2相弥散分布的全层片组织.该组织的室温及高温拉伸性能均较好.少量B2相对合金的室温塑性无不利影响,对合金的高温强度可能有一定贡献.     

Ti-22Nb-6Zr(at%)合金的超弹性和形状记忆效应

用弯曲法和拉伸法测定Ti-22Nb-6Zr（at％）合金的超弹性和形状记忆效应，研究固溶处理温度对Ti-22Nb-6Zr合金组织结构及性能的影响。结果表明：固溶处理后Ti-22Nb-6Zr合金的室温组织为单一的β相，晶粒尺寸随固溶处理温度升高而增大；合金的静态弹性模量小于30GPa；Ti-22Nb-6Zr合金具有良好的超弹性和一定的形状记忆效应。室温下变形，合金的超弹性和形状记忆效应随固溶处理温度升高而提高。900℃固溶处理后的合金在室温下拉伸变形，应变为5％时，总的最大回复应变达4．12％，其中超弹性回复应变为3．91％，记忆回复应变为0.21％。     

Ti-48Al-2Cr-2Nb-( TiB2, Ni)合金凝固组织演变规律及力学性能研究

TiAl合金已成为航空航天工程升级换代的关键材料,然而其铸态晶粒尺寸粗大,室温塑性和强度低,限制其进一步工程应用。本文采用真空感应凝壳熔炼工艺系制备铸锭,系统研究TiB2和Ni元素共同添加对Ti-48Al-2Cr-2Nb合金凝固组织和力学性能的影响。结果表明,TiB2及Ni合金化后,合金的凝固路径和初生相并未改变,晶粒尺寸从700μm细化至100μm,生成片状TiB2和富镍τ3相。T4822-( Ni, TiB2)合金的室温拉伸强度与基体合金相近,断裂伸长率提高30%。700-900℃时,T4822-(Ni, TiB2)合金的抗拉强度始终高于基体合金,在900℃时抗拉强度达到365MPa,较基体合金提高9%。800℃和900℃时T4822-(Ni, TiB2)合金的断裂伸长率分别达到25.3%和36.1%,远高于基体合金。晶粒尺寸的细化和晶界处的块状γ相是T4822-(Ni, TiB2)合金塑性提升的主要原因,其良好的高温强度则可以归因于片层团内部和界面处的硬质硼化物和富镍τ3相。     

热处理对Fe13Cr5Al1.5Nb合金晶粒尺寸及第二相析出行为的影响

利用光学显微镜、透射电镜、扫描电镜以及电子背散射衍射研究了Fe13Cr5Al1.5Nb合金的高温下微观组织演化特征。选择模拟事故工况温度区间(800～1000℃)对合金进行热处理实验,研究热处理温度和时间对晶粒尺寸及第二相析出行为的影响规律。采用EBSD分析统计了晶粒尺寸的变化。研究了800℃×20 h热处理后材料在室温至800℃的拉伸性能并观察分析了拉伸断口特征。结果表明,冷轧/热轧合金中弥散分布着高温稳定性良好的细小析出相(Fe2Nb相),且其周围分布着高密度位错。在800℃热处理5～25 h过程中,FeCrAl基合金的晶粒尺寸保持了良好的热稳定性,合金的晶粒尺寸都比较细小,平均晶粒尺寸约2μm。高于900℃时,合金中大量第二相固溶于基体,部分第二相显著粗化。低于260℃时,断口形貌表现为微孔型塑性断裂,呈现典型的细小蜂窝状等轴韧窝;提高到600～800℃时,合金出现超塑性特点。     

Er、Zr微合金化5083铝合金的超塑性

针对5E83合金(Er、Zr微合金化5083合金),采用超塑性拉伸试验、扫描电镜(SEM)、电子背散射衍射(EBSD)和透射电镜(TEM),探究了Er、Zr微合金元素、晶粒尺寸、变形温度、应变速率对合金超塑性的影响。通过再结晶退火、空冷和水冷的搅拌摩擦加工(FSP),分别获得了晶粒尺寸为7.4、5.2、3.4μm的完全再结晶组织,作为初始状态进行超塑性拉伸。结果表明,初始晶粒尺寸越细小,超塑性伸长率越高。当晶粒尺寸>5μm时,超塑性变形过程晶粒粗化缓慢,细化初始晶粒可显著提高超塑性;而当晶粒尺寸<5μm时,超塑性变形过程晶粒粗化严重,进一步细化初始晶粒对超塑性的提高有限。不同变形温度、应变速率的超塑性拉伸结果显示在变形温度为450～540℃、应变速率为1.67×10^-4～1.67×10^-1 s^-1,超塑性伸长率随变形温度和应变速率的提高呈现先上升后下降再上升的趋势;变形温度为520℃、应变速率为1.67×10^-3 s^-1条件下,水冷FSP态合金获得最大伸长率330%...     

航空用TA18合金管材热处理工艺研究

对冷轧后的TA18合金管材分别进行不同温度的热处理,分析热处理温度对TA18合金管材力学性能和组织的影响,选择最佳工艺进行成品批量热处理,测定室温拉伸性能及工艺性能。结果表明:在600~750℃热处理时,随热处理温度升高,管材的强度和塑性呈下降趋势,管材的内部组织再结晶程度增加,晶粒逐渐变大。在600℃热处理时,TA18合金管材可获得最佳的强塑性匹配;对成品管材进行600℃批量热处理,测得的管材室温拉伸性能及扩口、弯曲符合GJB 3423A要求。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

The Mirror with Patterns of Auspicious Animals and Grapes——Exquisite cast mirror and the technology of surface tin-enrichment by rubbing-in and infiltration of tin-rich powder

<正>Bronze mirrors were used by the Chinese people before the introduction of the glass mirror.Only after it was replaced by the glass mirror did the bronze mirror gradually retreat from people's lives.Different styles of bronze mirrors were made in different historical periods,particularly in the Warring States Period,the Han and Tang Dynasties,which were the three peaks of the development of bronze mirror arts in ancient China.The casting techniques were exquisite.The surface of the bronze mirror was smooth and bright enough to reflect one's image,and there were scarcely any casting defects on the mirror surface.On the back of the bronze mirror,there were rich depictions of Arts and Humanities,and the ornamentations were also     

The 9th China International Diecasting Congress & Exhibition

The 9th China International Diecasting Congress ＆ Exhibition was held on July 22-24, 2014 at Shanghai New International Expc Centre. This exhibition was the most successful over the years, with over 6890 visitors and 155 exhibitors, and the exhibition area increased by 30% from 9,500 square meters in 2012 to 12340 square meters. Die casting enterprises from a total of 24 countries and regions, including China mainland, Chinese Taiwan and Hong Kong, South Korea, Japan, Germany, India, Thailand, Malaysia, the United States, Russia, Australia, Iran, Ukraine, Brazil, Colombia, Singapore, Austria, Canada, Croatia, France, Turkey, United Kingdom, Vietnam, attended the congress and exhibition.     

Introduction of the Fluid Control Engineering Institute of Kunming University of Science and Technology

正The Fluid Control Engineering Institute of Kunming University of Science and Technology was set up in 1996.The researches of institute concentrate on electro-hydraulic(pneumatic)servo/proportional control and hydromechatronics.The Institute is committed to research and development of electro-hydraulic control of high-end technical equipment in ferrous metallurgy refining produc-     

RARE METALS Volume Contents

正~~     

Antimony Induced Crystallization of Amorphous Silicon

Antimony induced crystallization of PVD (physics vapor deposition) amorphous silicon can be observed on sapphire substrates. Very large crystalline regions up to several tens of micrometers can be formed. The Si diffraction patterns of the area of crystallization can be observed with TEM (transmission electron microscopy). Only a few and much smaller crystals of the order of 1μm were formed when the antimony layer was deposited by MBE (molecular beam epitaxy) compared with a layer formed by thermal evaporation. The use of high vacuum is essential in order to observe any Sb induced crystallization at all. In addition it is necessary to take measures to limit the evaporation of the antimony.     

A CUMULATIVE FATIGUE DAMAGE RULE UNDER THE ALTERNATIVE OF CORROSION OR CYCLIC LOADING

Fatigue damage increases with the applied loading cycles in a cumulative manner and the material deteriorates with the corrosion time. A cumulative fatigue damage rule under the alternative of corrosion or cyclic loading was proposed. The specimens of aluminum alloy LY12-CZ soaked in corrosive liquid for different times were tested under the constant amplitude cyclic loading to obtain S-N curves. The test was carried out to verify the proposed cumulative fatigue damage rule under the different combinations among corrosion time, loading level, and the cycle numbers. It was shown that the predicted residual fatigue lives showed a good agreement with the experimental results and the proposed rule was simple and can be easily adopted.