Determination of the glass transition temperature of latex films: Comparison of various methods

The glass transition temperature (T_g) for two latices with different styrene/butadiene compositions was determined by the thermal SPM probe resonance frequency method. The results were compared with the T_g values obtained by differential scanning calorimetry (DSC), dynamical mechanical analysis (DMA), process rheometer (PR) and thermo-mechanical analyzer (TMA) measurements. The T_g values detected by the thermal SPM method agreed well with the T_g values obtained by DSC and calculated by the Fox–Flory equation. DMA, on the other hand, showed a significantly higher T_g value for both latices than those obtained from theoretical calculations, the thermal SPM method and DSC. The T_g obtained from the PR curve was slightly higher for the latex with a low styrene content, whereas good agreement was obtained with the thermal SPM data for the latex with a high styrene content. The glass transition temperature determined by TMA agreed fairly well with the thermal SPM data for the latex with the low styrene content, whilst the value of T_g for the second latex was much less than those obtained by the other methods. The thermal SPM method detects changes in thermal behavior (thermal diffusivity, heat capacity) during heating of the latex films rather than changes in the mechanical properties. Information about the sample history could be seen in the thermal SPM curves, which was further associated with the degree of latex film formation, especially when the roughness of the films was taken into consideration.     

Melting and glass transitions in paraffinic and naphthenic oils

Naphthenic and paraffinic oils were analyzed by modulated differential scanning calorimetry (MDSC). The results showed several improvements in the analysis of thermal properties when compared with standard DSC. The glass transition temperature (T_g), the enthalpy relaxation at T_g, and the melting endotherms could be deconvoluted, and reversible melting could be identified. This allowed for an easier interpretation of the thermal properties of the oils. With MDSC, the T_gs in mineral oils were found to coincide with endothermic enthalpy relaxation, which is generally regarded as a melting endotherm with standard DSC. A decrease in heat capacity after T_g was attributed to the existence of rigid amorphous material. From Δc_p at T_g and the oil molecular weight, the number of repeat units in the oil chains was estimated at less than 20. The T_g of a hypothetical pure aromatic oil was found to be similar to that for petroleum asphaltenes, and that for a naphthenic oil of infinite molecular weight to be similar to that of petroleum resins.     

Liquid-crystalline side chain polymethacrylates II. Variation of spacer and central linkage in nitro-terminated polymers

The thermal behaviour and the mesogenic properties of liquid-crystalline side chain polymers with the structure are described with n = 3, 6, 8 or 11 and Z = -COO-, -CONH- or -N=N-. The polymers were made by radical chain polymerization. Most of them exhibit smectic phases, nematic phases were not observed. The amide linkage which has not yet been described as a structural element in such polymers gives rise to polymers of high polarity and high glass transition temperatures (T_g). In all cases the amide polymers produced the highest T_g values, the ester polymers showing the lowest. The azo polymers exhibited the largest mesophase ranges and the highest clearing temperatures (T_c1) of all the materials investigated. Whereas the T_c1 values for the azopolymers are nearly independent of the length of the spacer those of the amide and ester polymers show rising clearing points with increasing spacer length.     

Thermotropic main chain liquid crystalline polyesters containing ferrocene and phosphate units: synthesis and characterization

A new series of liquid crystalline main chain copolyesters were prepared, having ferrocene in the mesogenic segment and a methyl phosphate group along with a methylene spacer. The even numbered methylene groups were varied from two to ten. Liquid crystalline behaviour was investigated on a hot stage optical polarized microscope. Thermal properties of the polymers were analysed by TGA and DSC, revealing that the polymers yield high char products, probably caused by the formation of phosphorus and iron oxides. The glass transition (T_g) temperatures of the polymers were found to be fairly low, the result of the incorporation of bulky phosphorus and ferrocene moieties in the chain. The phase behaviour was analysed and correlated with the structure of the polymers. The liquid crystalline textures of the polymers became more transparent with increasing spacer length. Energy minimized structures for the polymer repeating units reveal that both the ferrocene and phosphorus moieties produce more molecular entanglement, thus reducing the T_g and T_m of the polymers.     

含三苯基氧磷结构聚芳醚醚酮酮的合成与表征

以苯酚、对二溴苯及苯基磷酰二氯为原料合成出二(4-苯氧基苯基)苯基氧磷(BPOPPO)。 三氯化铝(AlCl₃)为催化剂,通过缩聚反应,BPOPPO与对苯二甲酰氯(TPC)反应制备出一种含有三苯基氧磷结构的聚醚醚酮酮(P-PEEKK)树脂。 采用傅里叶变换红外光谱仪(FT-IR)、差示扫描量热仪(DSC)、热重分析仪(TGA)和广角X射线衍射(WAXD)等技术手段对P-PEEKK树脂的结构和性能进行表征。 结果表明,P-PEEKK树脂属于非晶聚合物,玻璃化转变温度(T_g)较高,为190.5 ℃;热分解温度(T_5%)为515 ℃,耐热性能较好;极限氧指数(LOI)为42,阻燃性能好,为难燃材料;易溶解于氯仿、1,2-二氯乙烷、N,N-二甲基乙酰胺等有机溶剂中,溶解性能较好,便于涂膜加工;拉伸强度为62 MPa,力学性能较好。     

Chemically Amplified Resist Based on Dendritic Molecular Glass for Electron Beam Lithography

A novel dendritic molecular glass(MG) containing adamantane core(AD-15) was synthesized and characterized. It exhibits good solubility in common organic solvents and a stable amorphous state at room temperature, which contributes to forming films with different thicknesses by spin-coating. The thermal analysis of AD-15 indicates that no apparent glass transition temperature(T_g) is observed before the thermal decomposition temperature(T_d=160 ℃). The good thermal resistance suggests that it can satisfy the lithographic process and is a candidate for photoresist materials. The patterning properties of AD-15 resist were evaluated by electron beam lithography(EBL). By optimizing the lithographic process parameters, AD-15 resist can achieve 40 nm half-pitch patterns with a line-edge roughness of 4.0 nm. The contrast and sensitivity of AD-15 resist were 1.9 and 67 μC/cm², respectively. Compared with the commercial PMMA(950k) electron beam resist, the sensitivity of AD-15 resist increases by 6 times. This study provides a new example of molecular glass resist with high resolution and sensitivity for EBL.     

快速扫描量热法研究聚对苯二甲酸-1,4-环己烷二甲醇酯的结晶和熔融行为

采用快速扫描量热法(FSC)结合传统的差示扫描量热仪(DSC)考察了聚对苯二甲酸-1,4-环己烷二甲醇酯(PCT)聚酯在接近玻璃化转变(T_g)和熔融温度(T_m)范围(100~270 ℃)的结晶和熔融行为。 较大过冷度时PCT聚酯结晶较快,FSC有效地抑制降温过程结晶的发生,而较低过冷度下传统DSC可以避免样品降解对实验结果的影响,二者的结合能很好地对PCT聚酯结晶动力学进行测量,实验结果表明在175 ℃时结晶速率最快。 并且利用Flash DSC对等温结晶温度下形成的片晶熔点进行加热速率的相关测量,在熔融动力学建模的基础上进行校准,以确定零加热速率下片晶的熔点。 Hoffman-Weeks方程中T_m与结晶温度(T_c)的线性关系与T_c=T_m的交点给出了PCT晶体的平衡熔融温度$T_m^o$为315 ℃。     

不同色浆质量分数的水性聚氨酯涂料对聚氯乙烯表皮低温爆破性能的影响

本文制备了一系列不同色浆质量分数的水性聚氨酯涂料,并将其喷涂在汽车仪表板聚氯乙烯(PVC)表皮的背面形成复合材料。 用旋转流变仪表征了涂料的粘度以评价其喷涂性能;用差示扫描量热仪表征了材料的玻璃化转变温度(T_g);利用万能材料试验机表征了材料在-30 ℃条件下的拉伸性能及抗撕裂性能;用动态热机械分析仪表征了材料的损耗比随温度的变化。 结果表明:不同色浆质量分数的涂料都能喷涂,含有涂层材料PVC表皮在-30 ℃低温爆破性能与涂层材料的T_g、低温拉伸性能、抗撕裂性能的关系并不大,而与涂层材料的阻尼性能直接相关。 材料的阻尼性能越好,其低温爆破性能越好。     

Poly(styrene-co-acrylonitrile) based proton conductive membranes

Sulfonated poly(styrene-co-acrylonitrile) (PSAN–SO₃H) membranes were obtained by sulfonation of the original styrene–acrylonitrile copolymer, in different molar ratios, and characterized by vibrational spectroscopy (FTIR), thermal analyses (TGA and DSC) and electrochemical impedance spectroscopy (EIS). The thermal stability of the sulfonated polymers exhibited a dependence on the sulfonation degree and reached 261 °C for samples up to 1:4 (sulfonating agent to styrene unit). FTIR spectra showed the covalent incorporation of sulfonic groups at the styrene units, confirming the PSAN–SO₃H formation. Vibrational spectra also indicated the presence of hydronium ions and dissociated sulfonic groups, indicating the existence of mobile protons for ion conduction. DSC analyses evidenced two glass transition temperatures (T_g), one associated with an ion-water domain and other with the chain backbone glass transition. The maximum conductivity of PSAN–SO₃H membranes at ambient temperature was about 10⁻³ Ω⁻¹ cm⁻¹, achieving 10⁻² Ω⁻¹ cm⁻¹ at 80 °C. The conductivity dependency on the temperature was found to be linear, similarly to other sulfonic acid polymers described on the literature, and the water uptake reaches 45.7% of the polymer mass, against 18.9% of the original copolymer.     

Preparation and characterization of side chain cholesteric liquid crystalline polysiloxanes containing two chiral groups

A series of liquid crystalline (LC) polysiloxanes containing diosgeninyl and menthyl groups (from monomers M₁ and M₂, respectively) were synthesized. The chemical structures of the monomers and polymers obtained were confirmed by elemental analysis, Fourier transform infrared spectroscopy, proton NMR and carbon-13 NMR. The LC properties were investigated by differential scanning calorimetry, thermogravimetric analysis, polarizing optical microscopy, and X-ray diffraction. Monomer M₁ showed cholesteric oily-streak and spiral textures. Copolymers P₂-P₅ exhibited cholesteric phases. With increasing concentration of M₂ units, the glass transition and clearing temperatures decreased. Experimental results demonstrated that a flexible polymer backbone and a long flexible spacer tended to favour a lower glass transition temperature, higher thermal stability, and wider mesophase temperature range.     

Consequences of the 'jacketed' effect on mesomorphic and orientational properties of 'side-on fixed' liquid crystalline polymers

The mesomorphic properties have been studied as a function of the degree of polymerization for certain 'side-on fixed' polyacrylates. A peculiar evolution of the clearing temperature, T_IN, as well as of the glass transition temperatures, T_g, revealed that beyond a certain backbone length, T_IN and T_g decrease as the main chain length increases. The nematic 'jacketed' structure of these polymers induces a more or less high anisotropy of the polymer backbone conformation in the nematic phase and this can counterbalance the usual effect of an increase in the degree of polymerization on the thermodynamical properties of these systems. This evolution allows us to explain the unusual diamagnetic anisotropy anomaly observed as a function of temperature for this type of polymer.     

不饱和聚酯片状模塑料的模压成型与性能

采用模压成型的方法制备了不饱和聚酯片状模塑料(UP-SMC)制品,通过万能试验机、热重分析、动态热机械分析、氧指数和纳米压痕技术研究了制品的力学性能、热稳定性能和阻燃性能。 结果表明,UP-SMC制品的弯曲强度和冲击强度分别达到203.4和94.2 MPa,由树脂过渡到纤维的各相微观力学性能是不同的。 该制品的玻璃化转变温度为169.4 ℃,在N₂气气氛下失重5 %(T_d5)和最大失重速率(T_dmax)对应的温度分别为333.5和389.7 ℃,600 ℃的质量保留率大于75%,极限氧指数为25.7%,表明该UP-SMC制品具有优异的力学性能和热稳定性能。     

The packing structure of side chains of liquid-crystalline side-chain polymers before and during heat treatment

Six varieties of liquid-crystalline side-chain polymers, poly (cholesteryl ω-(methacryloyloxy)alkanoates) (p-ChMO-n, n = 1,2,3,4,5,7, the carbon number of the alkyl chain), were studied by differential scanning calorimetry (DSC) and small-angle X-ray scattering (SAXS). On and after the first cooling run from the isotropic state, these polymethacrylates gave the same smectic phase. However, on the first heating run for virgin samples, unique phenomena were observed, similar to those frequently observed on the first heating run for thermotropic liquidcrystalline polymers. The thermal properties of the first heating run for these six polymers showed different tendencies between pChMO-n (n-1-3) and pChMO-n (4-7). Although the DSC curve of pChMO-n (n = 4, 5 and 7) exhibited the melting and clearing points on the first heating run, the DSC curve of pChMO-n (n = 1,2 and 3) exhibited an exothermal peak between the glass transition and the clearing point on the first heating run. This difference, probably due to the difference in the spacer length of these polymers, was investigated quantitatively by small-angle X-ray scattering by which the micro-change of the packing structure of the side chains of the polymers was traced.     

壳聚糖接枝聚乙烯吡咯烷酮复合碘膜的制备及其性能

将CTS接枝PVP后增加了分子间作用力(静电作用),使聚合物能够更加稳定的吸附碘分子,所以制备的CTS-PVP复合碘膜的抑菌性较CTS-PVP凝胶膜提高显著。     

Synthesis and thermal properties of poly(arylene ether ketone)s containing phthalazinone moieties

A series of novel poly(arylene ether ketone)s were synthesized from the reaction of hydroquinone and 4-(4-hydroxyphenyl)-2,3-phthalazin-1-one with 4,4′-difluorobenzophenone in N-cyclohexylpyrrolidinone containing anhydrous potassium carbonate. The polymers exhibited high glass transition temperatures together with excellent thermooxidative stability. The chain structure of these polymers was studied by means of differential scanning calorimetry (DSC), wide-angle X-ray diffraction techniques (WAXD), and matrix-assisted laser desorption/ionization time of flight mass spectrometry (MALDI-TOF-MS). The experimental results indicated that these “as-made” copoly(aryleneketone)s containing hydroquinone moieties exhibited a block chain structure with segments which mainly consisted of hydroquinone and 4,4′-difluorobenzophenone. These chain segments resulted in crystallites in the polymers although they are thermodynamically unstable. The polymers showed thermal properties comparable to commercial PEEK, but the conditions for synthesis are much milder. The glass transition temperatures and solubilities of the copoly(arylene ketone)s tended to increase with increasing phthalazinone moiety content, while the crystallite melting points and crystallinity appeared to decrease. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1781–1788, 1999     

耐超高温双酮酐型聚酰亚胺的合成及性能

以4,4'-对苯二甲酰二邻苯二甲酸酐(TDPA)为芳二酐单体,对苯二胺(PPD)为芳二胺单体,经低温溶液缩聚制得成膜性能优良的高相对分子质量聚酰胺酸(PAA),再经过热亚胺化制备双酮酐型聚酰亚胺(PI)薄膜。 采用傅里叶变换红外光谱仪(FT-IR)、广角X射线衍射(WAXD)、差示扫描量热仪(DSC)、动态热机械分析仪(DMA)、热重分析仪(TGA)、紫外-可见分光光度计(UV-Vis)及力学性能等技术手段表征了聚酰亚胺膜的结构和性能,考察了不同亚胺化温度对合成的双酮酐型聚酰亚胺膜性能的影响。 结果表明,经程序升温至320 ℃能使PAA热亚胺化基本趋于完成。 PI薄膜为部分有序聚集态结构,玻璃化转变温度(T_g)为298 ℃,具有优异的热性能,热失重温度(T_5%)为523 ℃。 拉伸强度达到130 MPa,弹性模量为5.77 GPa。 PI薄膜紫外光透过截止波长为375 nm,在可见光区具有良好的透光性能及耐溶剂性能。     

Preparation of conducting poly(vinyl chloride)/polyindole composites and freestanding films via chemical polymerization

This study covers the synthesis of conducting polyindole (PIN) homopolymer, poly(vinyl chloride)/polyindole (PVC/PIN) composites, and preparation of their freestanding films. PIN and composites were synthesized chemically by radicalic mechanism using FeCl₃ as an initiator. Films of PVC and PVC/PIN composites were prepared by casting on glass Petri dishes. Mechanical properties of films were examined by stress–strain experiments. From FTIR spectra of polymers, it was revealed that polymerization reaction occurred by 2–3 mechanism. The conductivities of polymers at different temperatures were also measured by four‐probe technique and found in the range 10^?4 to 10^?5 S cm^?1. Magnetic properties of the polymers were analyzed by Gouy scale measurements and were found that their conducting mechanisms are of polaron and bipolaron natures. Thermal properties of polymers were investigated by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) and found that they had shown adequate thermal stability. X‐ray diffraction (XRD) spectra showed the amorphous nature of the polymers. Scanning electron microscopy (SEM) was used for microstructural analysis. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1290–1298, 2010     

STUDY ON THE BLENDS OF NYLON 66 AND LIQUID CRYSTALLINE POLYESTERS

Blends of polyamide (Nylon 66) with two different kinds of liquid crystalline polyesters were studied in all the composition range. Homogeneous samples were obtained by coprccipitation from 2 wt%. solution of blends. The thermal properties, crystallinity and morphology of these blends were studied by using DSC, polarizing microscopy, and scanning electron microscopy. The phase transition and morphology of the blends are markedly-influenced by the composition of liquid crystalline polyesters. The mechanical behaviour of PHB/HNA-Nylon 66 blend was improved. although polyamidc (Nylon 66)with the liquid crystalline polyesters were incompatible, but a rather strong interaction between the polymers did exist.     

Miscibility and crystallinity of poly(3-hydroxybutyrate)/poly(3-hydroxybutyrate-co-3-hydroxyvalerate) blends

With the objective of developing new biodegradable materials, the miscibility and the crystallinity of blends of poly(3-hydroxybutyrate), P(3HB), and poly(3-hydroxybutyrate-co-3-hydroxyvalerate), P(3HB-co-3HV), have been studied. P(3HB) (300 kg mol⁻¹)/P(3HB-co-3HV)–10% 3HV (340 kg mol⁻¹) blends were prepared by casting in a wide range of proportions, and characterized by differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR). The experimental values for the glass transition temperatures (T_g) are in good agreement with the values provided by the Fox equation, showing that the blends are miscible. It was observed that the T_g and the melting temperature (T_m) decreases with the increase in the P(3HB-co-3HV)–10% 3HV content, while the crystallization temperature (T_c) increases. FT-IR analyses confirmed the decrease on the crystallinity of P(3HB)/P(3HB-co-3HV)–10% 3HV blends with higher copolymer contents. Bands related to the crystallinity were changed, due to the copolymer content that produced miscible and less crystalline blends.