Fabrication and characterization of electrospun silk fibroin/TiO2 nanofibrous mats for wound dressings

Silk fibroin (SF) nanofibrous mats were fabricated via electrospinning process. These fibers were blended with TiO₂ nanoparticles (TiO₂ NPs). The influence of TiO₂ NPs on the nanofibrous matrices was investigated by scanning electron microscopy (SEM), transmission electron microscopy, energy‐dispersive X‐ray, and thermogravimetric analysis. The SEM images revealed that the average diameter of the SF/TiO₂ fibers was 385 ± 63 nm when the concentration of SF was up to 10% (w/v). Infrared spectra showed that the β‐sheet structure of the silk fibroin increased after acetone treatment. These SF/TiO₂ nanofibrous mats exhibited higher equilibrium water content and water vapor transmission rate than hydrocolloid dressing. The hemocompatibility and cytocompatibility of SF/TiO₂ nanofibrous mats were evaluated by complete blood count, cell attachment, and the spreading of L929 fibroblasts. These SF/TiO₂ nanofibrous mats exhibited antibacterial activity against Escherichia coli under UV irradiation. Thus, these novel nanocomposite mats may be used for biomedical applications such as wound dressing. Copyright © 2011 John Wiley & Sons, Ltd.     

Aligned Bioactive Multi‐Component Nanofibrous Nanocomposite Scaffolds for Bone Tissue Engineering

The ability to mimic the chemical, physical and mechanical properties of the natural extra‐cellular matrix is a key requirement for tissue engineering scaffolds to be successful. In this study, we successfully fabricated aligned nanofibrous multi‐component scaffolds for bone tissue engineering using electrospinning. The chemical features were mimicked by using the natural components of bone: collagen and nano‐hydroxyapatite along with poly[(D ,L ‐lactide)‐co‐glycolide] as the major component. Anisotropic features were mimicked by aligning the nanofibers using a rotating mandrel collector. We evaluated the effect of incorporation of nano‐HA particles to the system. The morphology and mechanical properties revealed that,at low concentrations, nano‐HA acted as a reinforcement. However, at higher nano‐HA loadings, it was difficult to disrupt aggregations and, hence, a detrimental effect was observed on the overall scaffold properties. Thermal analysis showed that there were slight interactions between the individual components even though the polymers existed as a two‐phase system. Preliminary in vitro cell‐culture studies revealed that the scaffold supported cell adhesion and spreading. The cells assumed a highly aligned morphology along the direction of fiber orientation. Protein adsorption experiments revealed that the synergistic effect of increased surface area and the presence of nano‐HA in the polymer matrix enhanced total protein adsorption. Crosslinking with 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide hydrochloride resulted in improved mechanical properties of the scaffolds and improved degradation stability, under physiological conditions.

     

Electroactive electrospun polyaniline/poly[(L-lactide)-co-(ε-caprolactone)] fibers for control of neural cell function

Blends of PAni and PLCL are electrospun to prepare uniform fibers for the development of electrically conductive, engineered nerve grafts. PC12 cell viability is significantly higher on RPACL fibers than on PLCL-only fibers, and the electrical conductivity of the fibers affects the differentiation of PC12 cells; the number of cells positively-stained and their expression level are significantly higher on RPACL fibers. PC12 cell bodies display an oriented morphology with outgrowing neurites. On RPACL fibers, the expression level of paxillin, cdc-42, and rac is positively affected and proteins including RhoA and ERK exist as more activated state. These results suggest that electroactive fibers may hold promise as a guidance scaffold for neuronal tissue engineering.     

Formation and degradation of poly(D,L-lactide) nanoparticles and their potential application as controllable releasing devices

In the presence of surfactant, water-insoluble poly(D,L-lactide) (PLA) was dispersed into narrowly distributed nanoparticles stable in water via microphase inversion. The structure and degradation of such formed nanoparticles were investigated by a combination of static and dynamic laser light scattering. Our results revealed that the degradation rate increased with the temperature and pH so that the degradation could be regulated from minutes to days. Using anionic sodium dodecyl sulfate (SDS) as stabilizer resulted in a slower degradation than using cationic hexadecyltrimethylammonium bromide (HTAB). The phthalocyanine chromophores (PC) could be encapsulated inside these PLA nanoparticles. The degradation of individual PLA nanoparticles led to a controllable releasing of PC. The absorption and fluorescence studies revealed a correlation between the degradation and the releasing of PC. Our results showed that a higher PC/PLA ratio could lead to a faster degradation.     

Development of electroactive and elastic nanofibers that contain polyaniline and poly(L-lactide-co-epsilon-caprolactone) for the control of cell adhesion

In this work, electrically conductive polyaniline (PAni) doped with camphorsulfonic acid (CPSA) is blended with poly(L-lactide-co-epsilon-caprolactone) (PLCL), and then electrospun to prepare uniform nanofibers. The CPSA-PAni/PLCL nanofibers show a smooth fiber structure without coarse lumps or beads and consistent fiber diameters (which range from 100 to 700 nm) even with an increase in the amount of CPSA-PAni (from 0 to 30 wt.-%). However, the elongation at break decreases from 391.54 +/- 9.20% to 207.85 +/- 6.74% when 30% of CPSA-PAni is incorporated. Analysis of the surface of the nanofibers demonstrates the presence of homogeneously blended CPSA-PAni. Most importantly, a four-point probe analysis reveals that electrical properties are maintained in the nanofibers where the conductivity is significantly increased from 0.0015 to 0.0138 S x cm(-1) when the nanofibers are prepared with 30% CPSA-PAni. The cell adhesion tests using human dermal fibroblasts, NIH-3T3 fibroblasts, and C2C12 myoblasts demonstrate significantly higher adhesion on the CPSA-PAni/PLCL nanofibers than pure PLCL nanofibers. In addition, the growth of NIH-3T3 fibroblasts is enhanced under the stimulation of various direct current flows. The CPSA-PAni/PLCL nanofibers with electrically conductive properties may potentially be used as a platform substrate to study the effect of electrical signals on cell activities and to direct desirable cell function for tissue engineering applications.     

Synthesis and characterization of poly(vinyl alcohol)‐graft‐[poly(D,L‐lactide)/poly(D,L‐lactide‐co‐glycolide)] hydrogels

Poly(D ,L ‐lactide) and poly(D ,L ‐lactide‐co‐glycolide) with various composition and with one methacrylate and one carboxylate end group were synthesized and grafted onto poly(vinyl alcohol) (PVA) via the carboxylate group. The graft copolymers were crosslinked via the methacrylate groups using a free radical initiator. The polymer networks were characterized by means of NMR and studied qualitatively by means of IR spectroscopy. The influence of the glycolide content in the polyester grafts and of the number of ester units in the grafts on thermal properties and swellability were studied as well. The high swellability in water is characteristic of all hydrogels. Differential scanning calorimetry (DSC) showed a single glass transition temperature that occurs in the range between 51 and 69 °C. Thermogravimetric analysis (TGA) of the networks showed the main loss in weight in the temperature range between 290 and 370 °C. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4536–4544, 2007     

Microwave‐assisted synthesis and characterization of biodegradable block copolyesters based on poly(3‐hydroxyalkanoate)s and poly(D,L‐lactide)

Microwave (MW)‐assisted ring‐opening polymerization (ROP) provides a rapid and straightforward method for engineering a wide array of well‐defined poly(3‐hydroxyalkanoate)‐b‐poly(D,L ‐lactide) (PHA‐b‐PLA) diblock copolymers. On MW irradiation, the bulk ROP of D,L ‐lactide (LA) could be efficiently triggered by a series of monohydroxylated PHA‐based macroinitiators previously produced via acid‐catalyzed methanolysis of corresponding native PHAs, thus affording diblock copolyesters with tunable compositions. The dependence of LA polymerization on temperature, macroinitiator structure, irradiation time, and [LA]₀/[PHA]₀ molar ratio was carefully investigated. It turned out that initiator efficiency values close to 1 associated with conversions ranging from 50 to 85% were obtained only after 5 min at 115 °C. A kinetic investigation of the MW‐assisted ROP of LA gave evidence of its “living”/controlled character under the experimental conditions selected. Structural analyses and thermal properties of biodegradable diblock copolyesters were also performed. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Electrospun fiber mats of poly(3‐hydroxybutyrate), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate), and their blends

Electrospinning of poly(3‐hydroxybutyrate) (PHB), poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV), and their blends was first carried out in chloroform at 50 °C on a stationary collector. The average diameter of the as‐spun fiber from PHB and PHBV solutions decreased with increasing collection distance and increased with increasing solution concentration and applied electrical potential. In all of the spinning conditions investigated, the average diameter of the as‐spun pure fibers ranged between 1.6 and 8.8 μm. Electrospinning of PHB, PHBV, and their blends was carried out further at a fixed solution concentration of 14% w/v on a homemade rotating cylindrical collector. Well‐aligned, cross‐sectionally round fibers without beads were obtained. The average diameter of the as‐spun pure and blend fibers ranged between 2.3 and 4.0 μm. The as‐spun fiber mats appeared to be more hydrophobic than the corresponding films and much improvement in the tensile strength and the elongation at break was observed for the blend fiber mats over those of the pure fiber ones. Lastly, indirect cytotoxicity evaluation of the as‐spun pure and blend fiber mats with mouse fibroblasts (L929) indicated that these mats posed no threat to the cells. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2923–2933, 2006     

Nanofibrous Membranes Containing Carbon Nanotubes: Electrospun for Redox Enzyme Immobilization

Summary: Nanofibrous membranes that possess reactive groups are fabricated by the electrospinning process from PANCAA solutions that contain MWCNTs. Field emission scanning electron microscopy is used to evaluate the morphology and diameter of the nanofibers. Potentials for applying these nanofibrous membranes to immobilize redox enzymes by covalent bonding are explored. It is envisaged that the electrospun nanofibrous membranes could provide a large specific area and the MWCNTs could donate/accept electrons for the immobilized redox enzymes. Results indicate that, after blending with MWCNTs, the diameter of the PANCAA nanofiber increases slightly. The PANCAA/MWCNT nanofibrous membranes immobilize more enzymes than that without MWCNTs. Moreover, as the concentration of the MWCNTs increases, the activity of the immobilized catalase is enhanced by about 42%, which is mainly attributed to the promoted electron transfer through charge‐transfer complexes and the π system of MWCNTs.

The covalent immobilization of redox enzymes, such as catalase, on a PANCAA/MWCNTs nanofiber.     

Biodegradable electrospun mat: Novel block copolymer of poly (p‐dioxanone‐co‐L‐lactide)‐block‐poly(ethylene glycol)

Ultrafine fibers of a laboratory‐synthesized new biodegradable poly(p‐dioxanone‐co‐L ‐lactide)‐block‐poly(ethylene glycol) copolymer were electrospun from solution and collected as a nonwoven mat. The structure and morphology of the electrospun membrane were investigated by scanning electron microscopy, differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction (WAXD), and a mercury porosimeter. Solutions of the copolymer, ranging in the lactide fraction from 60 to 80 mol % in copolymer composition, were readily electrospun at room temperature from solutions up to 20 wt % in methylene chloride. We demonstrate the ability to control the fiber diameter of the copolymer as a function of solution concentration with dimethylformamide as a cosolvent. DSC and WAXD results showed the relatively poor crystallinity of the electrospun copolymer fiber. Electrospun copolymer membrane was applied for the hydrolytic degradation in phosphate buffer solution (pH = 7.5) at 37 °C. Preliminary results of the hydrolytic degradation demonstrated the degradation rate of the electrospun membrane was slower than that of the corresponding copolymers of cast film. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1955–1964, 2003     

Mechanism of high thermal stability of commercial polyesters and polyethers conjugated with bio‐based caffeic acid

In previous report, we discovered that a novel improvement technique to enhance the thermal properties of poly(L ‐lactide)s (PLLAs) by terminal conjugation with 3,4‐diacetoxycinnamic acid (DACA). In this study, we clarified the mechanism of the enhancement of thermal stability by using commercial polyesters and polyethers. The effect of thermal improvement by the terminal conjugation of DACA on poly(DL ‐lactide), poly(ε‐caprolactone), and poly(ethylene glycol) was almost the same as about 100 °C increase. The amount of residual tin catalyst, which enhances the thermal degradation of polyesters, was reduced at undetected level after the terminal conjugation of DACA probably due to the removal of tin during DACA conjugation process. Furthermore, the π‐π stacking interactions of DACA units and the chemical protection of terminal hydroxyl groups, which enhances intramolecular scission, were also important for the high thermal stability. We clarified that the extreme high thermal stability by DACA conjugation was induced by these above mechanisms. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

FT‐IR characterization and hydrolysis of PLA‐PEG‐PLA based copolyester hydrogels with short PLA segments and a cytocompatibility study

A series of the biodegradable copolyester hydrogels was prepared using a redox‐initiated polymerization with a constant 1:9 mole ratio of the Boltorn‐based acrylate and diacrylate triblock comacromonomers. The Boltorn® macromonomer was derived from the hyperbranched polyester Boltorn H20, which was functionalized at each terminus with poly(ethylene glycol) acrylate, and the diacrylate triblock macromonomer was poly (lactide‐b‐ethylene glycol‐b‐lactide) diacrylate. The hydrolysis of the copolyesters at pH 7.4 in a phosphate buffered saline solution at 37 °C was studied using ATR‐FTIR spectroscopy. It was found that the presence of the Boltorn, the PEG, and lactide block lengths both play vital roles in determining the structure‐property relationships in these materials. The ATR‐FTIR studies showed that with increasing lactide segment length, the rate of ester hydrolysis increased due to the increased concentration of the hydrolytically sensitive poly(lactic acid) (PLA) ester groups in the network. However, incorporation of Boltorn into the PLA‐PEG‐PLA copolymer did not significantly change the kinetic rate constant for hydrolysis of the PLA segments. The cytocompatibility of a typical one of these materials in the presence of its degradation by‐products was assessed using cultured osteoblasts from the rat. The hydrogel was degraded for 28 days and found to be cytocompatible with osteoblasts over days 23 to 28 of the hydrolysis period. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5163–5176     

Effect of gamma‐irradiation sterilization on the physical and mechanical properties of a hybrid wound dressing

A wound dressing should ideally provide an optimal healing environment which enables rapid healing. It should maintain a moist environment at the wound surface, allow gas exchange, act as a barrier to microorganisms, remove excess exudates and afford mechanical protection to the wound. A new bioresorbable hybrid wound dressing which combines a poly(DL‐lactic‐co‐glycolic acid) porous top layer with a spongy collagen sublayer was developed and studied. The top layer contained the antibiotic drug gentamicin for controlled release to the wound site. It is of very high importance to use an appropriate sterilization process for this special new wound dressing, which will not have a deleterious effect on its function. Our investigation therefore focused on the effects of gamma‐irradiation sterilization (10, 25, 35 and 50 kGy) on the structure properties of this wound dressing. The physical and mechanical properties were of the wound dressings were affected by the gamma irradiation because of a combination of chain scission and crosslinking of the collagen layer mainly. The weight loss and water vapor transmission rate were increased, while the water uptake was decreased with the increase in the irradiation dose. The changes were small when doses of 10 or 25 kGy were applied at room temperature. The gamma‐irradiation resulted in stronger but more brittle wound dressings. These trends were smaller when the sterilization process was carried out in liquid nitrogen. Our research shows that gamma‐sterilization process is feasible for our new concept of hybrid wound dressings and optimal conditions can be chosen. Copyright © 2016 John Wiley & Sons, Ltd.     

Chemo-physical and biological evaluation of poly(L-lysine)-grafted chitosan copolymers used for highly efficient gene delivery

For the success of non-viral gene delivery, it is of great importance to develop gene vectors with high efficiency but low toxicity. We demonstrate that PLL-grafted chitosan copolymers combine the advantages of PLL with its good pDNA-binding ability and of chitosan with its good biocompatibility. The chemo-physical properties of the prepared Chi-g-PLL copolymers are thoroughly characterized. The in vitro transfection study shows that the copolymers have a much higher gene transfer ability than the starting materials chitosan and PLL. A positive correlation between PLL chain lengths and transfection efficiency of the copolymers is found. Our results suggest that these novel Chi-g-PLL copolymers are good candidates for gene delivery in vivo.     

Paclitaxel‐Loaded Stabilizer‐Free Poly(D,L‐lactide‐co‐glycolide) Nanoparticles Conjugated with Quantum Dots for Reversion of Anti‐Cancer Drug Resistance and Cancer Cellular Imaging

We prepared the PLGA‐loaded anti‐cancer drug and coated it with quantum dots to make it a dual‐function nanoparticles, and analyzed its potential use in cellular imaging and curing cancers. Two cancer cell lines, paclitaxel‐sensitive KB and paclitaxel‐resistant KB paclitaxel‐50 cervical carcinoma cells, were the relativistic models for analysis of the cytotoxicity of free paclitaxel and paclitaxel‐loaded PLGA conjugated with quantum‐dot nanoparticles. The paclitaxel‐loaded PLGA conjugated with quantum dots nanoparticles were significantly more cytotoxic than the free paclitaxel drug in paclitaxel‐resistant KB paclitaxel‐50 cells. This might have been because the cancer cells developed multi‐drug resistance (MDR), which hampered the action of free paclitaxel by pumping its molecules to extracellular areas. Addition of verapamil, a P‐glycoprotein inhibitor, reversed the MDR mechanism and significantly reduced KB paclitaxel‐50 cell viability. As a result, KB paclitaxel‐50 was highly associated with MDR on the cell membrane. The cytotoxicity results indicated that PLGA nanoparticles served as drug carriers and protected the drugs from MDR‐accelerated efflux. Combined quantum dots with PLGA nanoparticles allowed additional functionality for cellular imaging.     

Synthesis,characterization, effect of architecture on crystallization,and spherulitic growth of poly(L‐lactide)‐b‐poly(ethylene oxide) copolymers with different branch arms

Well‐defined poly(L ‐lactide)‐b‐poly(ethylene oxide) (PLLA‐b‐PEO) copolymers with different branch arms were synthesized via the controlled ring‐opening polymerization of L ‐lactide followed by a coupling reaction with carboxyl‐terminated poly(ethylene oxide) (PEO); these copolymers included both star‐shaped copolymers having four arms (4sPLLA‐b‐PEO) and six arms (6sPLLA‐b‐PEO) and linear analogues having one arm (LPLLA‐b‐PEO) and two arms (2LPLLA‐b‐PEO). The maximal melting point, cold‐crystallization temperature, and degree of crystallinity (X_c) of the poly(L ‐lactide) (PLLA) block within PLLA‐b‐PEO decreased as the branch arm number increased, whereas X_c of the PEO block within the copolymers inversely increased. This was mainly attributed to the relatively decreasing arm length ratio of PLLA to PEO, which resulted in various PLLA crystallization effects restricting the PEO block. These results indicated that both the PLLA and PEO blocks within the block copolymers mutually influenced each other, and the crystallization of both the PLLA and PEO blocks within the PLLA‐b‐PEO copolymers could be adjusted through both the branch arm number and the arm length of each block. Moreover, the spherulitic growth rate (G) decreased as the branch arm number increased: G_{6sPLLA‐b‐PEO} < G_{4sPLLA‐b‐PEO} < G_{2LPLLA‐b‐PEO} < G_{LPLLA‐b‐PEO}. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2034–2044, 2006     

Elaboration of densely functionalized polylactide nanoparticles from N‐acryloxysuccinimide‐based block copolymers

Poly(N‐acryloxysuccinimide) (PNAS) and poly(N‐acryloxysuccinimide‐co‐N‐vinylpyrrolidone) (P(NAS‐co‐NVP)) of adjustable molecular weights and narrow polydispersities were prepared by nitroxide‐mediated polymerization (NMP) in N,N‐dimethylformamide in the presence of free SG1 (N‐tert‐butyl‐N‐1‐diethylphosphono‐(2,2‐dimethylpropyl) nitroxide), with MAMA‐SG1 (N‐(2‐methylpropyl)‐N‐(1‐diethylphosphono‐2,2‐dimethylpropyl)‐O‐(2‐carboxylprop‐2‐yl)hydroxylamine) alkoxyamine as initiator. The reactivity ratios of NAS and NVP were determined to be r_NAS = 0.12 and r_NVP = 0, indicating a strong alternating tendency for the P(NAS‐co‐NVP) copolymer. NAS/NVP copolymerization was then performed from a SG1‐functionalized poly(D ,L ‐lactide) (PLA‐SG1) macro‐alkoxyamine as initiator, leading to the corresponding PLA‐b‐P(NAS‐co‐NVP) block copolymer, with similar NAS and NVP reactivity ratios as mentioned above. The copolymer was used as a surface modifier for the PLA diafiltration and nanoprecipitation processes to achieve nanoparticles in the range of 450 and 150 nm, respectively. The presence of the functional/hydrophilic P(NAS‐co‐NVP) block, and particularly the N‐succinimidyl (NS) ester moieties at the particle surface, was evidenced by ethanolamine derivatization and zeta potential measurements. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Cytocompatibility and antibacterial activity of a PHBV membrane with surface-immobilized water-soluble chitosan and chondroitin-6-sulfate

A water-soluble chitosan (WSC)/chondroitin-6-sulfate (ChS) polyelectrolyte complex (PEC) is covalently immobilized onto the surface of poly(3-hydroxybutyric acid-co-3-hydroxyvaleric acid) (PHBV) membranes via ozone-induced oxidation and poly(acrylic acid) (PAA) graft polymerization. To characterize the modified membranes, X-ray photoelectron spectroscopy (XPS) and water contact angle measurements are performed. It is shown that by coupling WSC as a spacer, the amount of ChS immobilized can be significantly increased. The water contact angle decreases with the amount of PAA, WSC, and ChS immobilized, which indicates the improving hydrophilicity. After WSC- and PEC-immobilization modification, the PHBV membranes possess antibacterial activity against S. aureus, E. coli, P. aeruginosa, and Methicilin resistant Staphylococus aureus (MRSA). According to the L929 fibroblast cell growth inhibition index, the as-prepared PHBV membranes are non-cytotoxic. In addition, the in-vitro evaluation of L929 fibroblast attachment, proliferation, and viability of PEC-immobilized PHBV membranes are ascertained to be superior to those of immobilized WSC or ChS alone. The overall results demonstrate that WSC/ChS PEC immobilization can not only improve the hydrophilicity and cytocompatibility of the PHBV membrane, but also endows antibacterial activity. [GRAPH: SEE TEXT] The bacterial survival ratio of as-prepared PHBV membranes (n=3).     

Synergistic effects of PEG and MWCNTs on crystallization behavior of PLLA

This work reported the crystallization behaviors of poly(L ‐lactide) (PLLA) with the presence of polyethylene glycol (PEG) and/or functionalized multiwalled carbon nanotubes (FMWCNTs). The crystallization behaviors occurred in the different conditions, including nonisothermal, isothermal and during the annealing process, were analyzed comparatively using differential scanning calorimetry, wide angle X‐ray diffraction, and polarized optical microscope. The results show that PEG as an efficient plasticizer of PLLA enhances the mobility of PLLA chain segments, which leads to the decrease of glass transition temperature and the enhancement of crystallization ability of PLLA. FMWCNTs as a nucleating agent of PLLA crystallization promote the crystallization of PLLA apparently. With the presence of PEG and FMWCNTs, the crystallization of PLLA is well improved in all conditions, indicating the synergistic effects of PEG and FMWCNTs on PLLA crystallization. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 520–528, 2010