High-frequency dielectric properties of Mg-Al-Si,Ca-Al-Si and Y-Al-Si oxynitride glasses

Recently developed coaxial line techniques [1] have been used to determine, at room temperature, the values of the real () and imaginary (') parts of the dielectric constants for some Mg-Al-Si, Ca-Al-Si and Y-Al-Si oxynitride glasses over the frequency range 500 MHz to 5 GHz. The frequency dependencies of and ' are consistent with the universal law of dielectric response in that (-_t8)^(n–1) and '^(n–1) for all glass compositions; the high experimental value of the exponent (n=1.0±0.1) suggests the limiting form of lattice loss [2] situation. In this frequency range, as previously reported [3] at longer wavelengths, the addition of nitrogen increases the dielectric constant, (); in both the oxide and oxynitride glasses is also influenced by the cation, being increased with cation type in the order magnesium, yttrium, calcium as at lower frequencies.     

Dielectric Properties of Melt-Grown Cd1 – xZnxTe Crystals

The real (") and imaginary (") parts of the complex dielectric permittivity of Cd_{1 – x} Zn _x Te (x= 0.1–0.2) crystals are measured as a function of temperature and frequency. The "-vs.-temperature data show a maximum, and " rises rapidly at about the same temperature. This behavior is interpreted in terms of compositional fluctuations, structural defects, and the associated internal electric fields.     

Dielectric properties of chemically vapour-deposited Si3N4

The dielectric properties of chemically vapour-deposited (CVD) amorphous and crystalline Si₃N₄ were measured in the temperature range from room temperature to 800° C. The a.c. conductivity ( _a.c.) of the amorphous CVD-Si₃N₄ was found to be less than that of the crystalline CVD-Si₃N₄ below 500° C, but became greater than that of the crystalline CVD-Si₃N₄ over 500° C due to the contribution of d.c. conductivity ( _d.c.). The measured loss factor () and dielectric constant () of the amorphous CVD-Si₃N₄ are smaller than those of the crystalline CVD-Si₃N₄ in all of the temperature and frequency ranges examined. The relationships of ^n-1, (- ) ^n-1 and/(- ) = cot (n/2) (were observed for the amorphous and crystalline specimens, where is angular frequency andn is a constant. The values ofn of amorphous and crystalline CVD-Si₃N₄ were 0.8 to 0.9 and 0.6 to 0.8, respectively. These results may indicate that the a.c. conduction observed for both of the above specimens is caused by hopping carriers. The values of loss tangent (tan) increased with increasing temperature. The relationship of log (tan) T was observed. The value of tan for the amorphous CVD-Si₃N₄ was smaller than that of the crystalline CVD-Si₃N₄.     

On the analysis of tunneling data for A15 superconductors

We examine the applicability of the standard McMillan inversion of Eliashberg's equations for superconductors with a nonconstant electronic density of statesN(). We do this usign simple models forN() and a realistically shapedN() taken from recent band structure work for Nb₃Sn. It turns out that peak structure inN() near _F may lead to gross errors in the derived Eliashberg function ²F() when the energy dependence ofN() is omitted in the inversion procedure. For Nb₃Sn, this leads to a 40% overestimate of when ²F() is evaluated via the standard McMillan program.     

A Method for Calculating Thermal Radiation Properties of Multilayer Films from Optical Constants

A calculation method for the incident angle dependence of the solar absorptance _S and the temperature dependence of the total hemispherical emittance _H of multilayer films is proposed. The method is based on calculation of _S and _H from optical constants in the wavelength region from 0.25 to 100 m for thin polymer films and deposited metal. In this paper we provide values of _S in the incident angle region from 0 to 90° and _H in the temperature range from 173.15 to 373.15 K for two-layer samples of aluminum-deposited polyimide film. The results obtained for _S and _H by the present method are compared with experimental results measured by both spectroscopic and calorimetric methods. The calculated results of _S and _H agree well with the experimental results.     

Asymptotics beyond all orders for a low Reynolds number flow

The solution for slow incompressible flow past a circular cylinder involves terms in powers of 1/log , times powers of 1/log , etc., where is the Reynolds number. Previously we showed how to determine the sum of all terms in powers of 1/log . Now we show how to go beyond all those terms to find the sum of all terms containing times a power of 1/log . The first sum gives the drag coefficient and represents a symmetric flow in the Stokes region near the cylinder. The second term reveals the asymmetry of the flow near the body. This problem is studied using a hybrid method which combines numerical computation and asymptotic analysis.     

The role of ε-martensite in the impact toughness of an Fe-17Mn alloy

The influence of -martensite on the cryogenic toughness of an Fe-17 wt% Mn alloy was studied in this work. Alloys were tempered at various temperatures in order to systematically increase the volume fraction of -martensite. This was followed by Charpy impact testing conducted at room temperature and at–196°C. The experimental results indicated that although room-temperature toughness was not influenced by the -martensite content, the cryogenic toughness was strongly dependent on the volume fraction of -martensite. In particular, with the exception of the alloys tempered at 400 and 450°C, the impact toughness consistently increased with -martensite content. Microstructural and fractographic evaluations using SEM and TEM suggested that the toughness improvements were attributed to the stress-induced martensite transformation. No microstructural evidence was found which could be ascribed to an effect of -martensite on the low-temperature embrittlement exhibited by Fe-Mn alloys tempered at 400–450°C.     

A model with length scales for composites with periodic structure. Steady state heat conduction problem

A new high-order model for analysing distribution of temperature in periodic composites is proposed. The original scalar elliptic problem with Y-periodic coefficients (Y is a cube) is replaced with a vectorial elliptic problem of constant coefficients. The unknown fields are: the averaged distribution of temperature and the vector field which stands for perturbation of the temperature within the cells of periodicity. The recovery of temperature in the original composite is given by the approximation: 0(x)=0(x) +h ^a (x/) _a (x) analogous with the first terms of the two-scale asymptotic expansion known from the homogenization theory. The functions h are defined as approximations of the solutions to the basic cell problems. In contrast to the two-scale expansion the expression for satisfies the boundary condition.     

The dielectric properties of glass-ceramic-on-metal substrates for microelectronics packaging

The dielectric properties of some glass-ceramic-on-metal substrates have been determined over the frequency range 500 Hz to 5 MHz using a.c. bridge techniques. The substrates consisted of cordierite-based glass-ceramics screen printed on molybdenum. For glass layers of thickness greater than 100 m both the permittivity, and the dielectric loss, , are frequency independent over this frequency range at room temperature giving the value of =6.5 and tan =8×10^–3; the room-temperature data are consistent with the universal law of dielectric response. The variation of permittivity with temperature has also been examined and, below 120 °C, the temperature coefficient [(–1) (+2)]^–1 (/T)_p, was found to be 1.3×10^–5 K^–1. The results are compared with those previously reported for Al₂O₃ and AIN substrates.     

Fatigue properties of pure metals

The report considers the stress fatigue limit _D, the fatigue to tensile strength ratio _D/R_m, and the deformation fatigue limit _D of pure metals. For FCC and some HCP metals there exists a linear correlation between fatigue limit and tensile strength. The fatigue limit and the fatigue ratio _D/R_m depend upon the homologous temperature. The fatigue ratios of BCC metals are higher than the fatigue ratios of other metals at room temperature as is also true for metals with nearly the same homologous temperature. The deformation fatigue limit decreases rapidly when T_h - 0.5 and T_h 1. When T_h = 1 then _D = 0, _D = 0 and _D/R_m = 0. The deformation fatigue limits of metals belonging to the same subgroup of the periodic element system and having, similar homologous temperatures at room temperature are very similar.

---

Zusammenfassung Der Artikel behandelt die Dauerfestigkeit _D des Ermuedungskoeffizienten _D/R_m und die Deformation _D, die der Dauerfestigkeit entspricht. Fuer kubisch flachzentrierte Metalle und einige hexagonal Metalle existiert eine lineare Korrelation zwischen Dauerfestigkeit _D and Zugfestigkeit R_m. Die Dauerfestigkeit _D und der Ermuedungskoeffizient _D/R_m koennen als Funktion der homologischen Temperatur betrachtet werden. Der Ermuedungskoeffizient der kubisch raumzentrierten Metalle ist groesser als der der anderen in Raumtemperatur. Dieses stimmt auch fuer Metalle mit aehnlichen hornologischen Temperaturen. Die Deformation _D, die der Dauerfestigkeit entspricht, faellt schnell ab, wenn T_h > 0.5 und T_h 1, Wenn T_h = 1, darn ist _D = 0, _D = 0 und _D/R_m = 0. Die Metalle, die zu derselben Gruppe des periodischen Systems der Elemente gehoeren and aehnliche homologische Temperaturen (in Raumtemperatur) besitzen, haben sehr aehnliche Werte der Deformation _D.

---

Résumé L'article parle de la contrainte de la limite de fatigue _D le facteur de fatigue _D/R_m et la déformation _D correspondante à la limite de fatigue des métaux pures. Pour les métaux du système cubique aux faces centrées (c. f. c.) et quelques uns du système hexagonale (hex. c.) il existe une correlation linéare entre la limite de fatigue _D et de la résistance a la fraction R_m. La limite de fatigue _D et le facteur de fatigue _D/R_m dependent de la température homologue. Les facteurs de la fatigue des métaux du système cubique centre (c.c.) sort plus grands que ceux des autres métaux dans la température de chambre, aussi por des métaux qui ont presque la même température homologue. La déformation correspondante à la limite de fatigue tombe rapidement quand T_h > 0.5 et T_h 1. Quand T_h = 1, alors _D = 0, _D = 0 et _D/R_m = 0. Cettes déformations _D pour les métaux du même groupe du système périodique des éléments sont proches si les températures homologues dans la température de chambre sont analogues.

     

Deformation approach to the evaluation of the period of initiation and growth of fatigue macrocracks

We performed experimental investigation of the opening displacements of the contours of stress concentrators (notches and cracks) for various amplitudes of cyclic loading. On the basis of experimental results, we propose a new deformation parameter _t which is a function of the notch (crack) tip opening displacement , namely, _t /(+d*), where is the radius of the tip of the notch andd* is the characteristic size of the prefracture zone. It is shown that this parameter uniquely determines the number of cyclesN _l to the initiation of a fatigue macrocrack independently of the geometry of the specimens and stress concentrators in elastic and elastoplastic materials, i.e., the dependence of _t onN ₁ is a characteristic of the material. It is experimentally demonstrated that this dependence enables one to quantitatively describe the process of fatigue fracture both in the stage of initiation of macrocracks and their propagation.Karpenko Physicomechanical Institute, Ukrainian Academy of Sciences, L'viv. Translated from Fiziko-Khimicheskaya Mekhanika Materialov, Vol. 31, No. 5, pp. 7–21, September – October, 1995.     

Effect of crystalline phase, orientation and temperature on the dielectric properties of poly (vinylidene fluoride) (PVDF)

The effect of crystalline phase, uniaxial drawing and temperature on the real () and imaginary () parts of the relative complex permittivity of poly (vinylidene fluoride) (PVDF) was studied in the frequency range between 10² and 10⁶ Hz. Samples containing predominantly and phases, or a mixture of these, were obtained by crystallization from a DMF solution at different temperatures. phase samples were also obtained from melt crystallization and from commercial films supplied by Bemberg Folien. Different molecular orientations were obtained by uniaxial drawing of and phase samples. The results showed that the crystalline phase exerts strong influence on the values of and , indicating that the _a relaxation process, associated with the glass transition of PVDF, is not exclsively related to the amorphous region of the polymer. An interphase region, which maintains the conformational characteristics of the crystalline regions, should influence the process decisively. The molecular orientation increased the values of for both PVDF phases and modified its dependence with temperature over the whole frequency range studied. The influence of the crystallization and molecular orientation conditions on the dc electric conductivity (_dc) were also verified. The value of _dc was slightly higher for samples crystallized from solution at the lowest temperature and decreased with draw ratio.     

A method of joint determination of the effective coefficients of horizontal mixing of large particles and of external heat exchange in an organized fluidized bed

A method is proposed for the joint determination of the coefficients of horizontal particle diffusion and external heat exchange in a stagnant fluidized bed.Notation c_f, c_s, c_n specific heat capacities of gas, particles, and nozzle material, respectively, at constant pressure - D effective coefficient of particle diffusion horizontally (coefficient of horizontal thermal diffusivity of the bed) - d equivalent particle diameter - d_t tube diameter - H₀, H heights of bed at gas filtration velocities u₀ and u, respectively - H_a height of active section - l width of bed - L tube length - l _o width of heating chamber - N number of partition intervals - p=H/H₀ expansion of bed - s_n surface area of nozzle per unit volume of bed - S_h, S_v horizontal and vertical spacings between tubes - t_c, t₀, t_s, t_n, t_w initial temperature of heating chamber, entrance temperature of gas, particle temperature, nozzle temperature, and temperature of apparatus walls, respectively - u₀, u velocity of start of fluidization and gas filtration velocity - y horizontal coordinate - ^*, coefficient of external heat exchange between bed and walls of apparatus and nozzle - ₁, ₁, ₂, ... coefficients in (4) - thickness of tube wall - _b bubble concentration in bed - ₀ porosity of emulsion phase of bed - _n porosity of nozzle - =(t_s – t₀)/(t_c – t₀) dimensionless relative temperature of particles - _n coefficient of thermal conductivity of nozzle material - f, _s, _n densities of gas, particles, and nozzle material, respectively - _be=_s(1 – ₀) (1 – _b) average density of bed - time - _max time of onset of temperature maximum at a selected point of the bed - R =l _o/l Fourier number - Pe = ₁ l ²/D Péclet number - Bi = /_n Biot number Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 41, No. 3, pp. 457–464, September, 1981.     

Slip flow past an approximate spheroid

Summary Creeping axisymmetric slip flow past a spheroid whose shape deviates slightly from that of a sphere is investigated. An exact solution is obtained to the first order in the small parameter characterizing the deformation. As an application, the case of flow past an oblate spheroid is considered and the drag experienced by it is evaluated. Special well-known cases are deduced and some observations made.Notation A _n, B_n, C_n, D_n, E_n, F_n, b₂, d₂ Constants - a, b radii of spheres - coefficient of sliding fraction - D drag - , _m parameters characterizing the deformation of the sphere - c a(1+) - viscosity coefficient - - dimensionless coordinate - I _n Gegenbauer function - P _n Legendre function - Stream function - U stream velocity at infinity     

Dielectric Dispersion in Yttrium and Erbium Formate Dihydrate Crystals

The dielectric properties of Y(HCOO)₃ · 2H₂O and Er(HCOO)₃ · 2H₂O are studied. The frequency dependences (0.01 Hz to 20 kHz) of the real () and imaginary () parts of dielectric permittivity ( = – i) are shown to follow a fractal scaling law for the dielectric response of solids. In the tan versus temperature curves, a number of maxima are revealed in a narrow temperature range. The experimental data are used to evaluate the activation energies of relaxation processes. The observed anomalies are assumed to be associated with changes in the dynamics of protons in hydrogen bonds.     

Dielectric properties of nanostructured nickel oxide

Nanostructured NiO samples having different average particle sizes were prepared and the variations of the real and imaginary components of the complex dielectric function * were studied as a function of the frequency of the applied signal and temperature. The dielectric relaxation mechanism is discussed considering nanostructured NiO as a carrier dominated dielectric with high density of hopping charge carriers. The observed ^{n – 1} dependence of the real and imaginary components of * is discussed in the light of the 'Universal' model of dielectric response. The various contributions to the measured dielectric loss such as the steady state charge transport, delayed readjustment of screening charges and the Debye delays are discussed. It is shown that the temperature dependence of both the real and imaginary components of * are in accordance with the models used for discussing the dielectric relaxation and loss mechanisms. The variation of with average particle size seems to be rather complex depending on a number of parameters associated with the interfacial region which vary with the average particle size.     

Dielectric anomalies in monoclinic TlInS<Subscript>2</Subscript> polytypes

Comparison of room-temperature x-ray diffraction data and temperature-dependent (190–220 K) permittivity data for different polytypes of monoclinic TlInS₂ demonstrates that the anomalies in (T) at the phase transition correlate with the c cell parameter of the polytypes. The (T) curve of single-phase crystals with c 15 Å shows a single, sharp peak at about 205 K. The peaks in the of the polytypes with c 30 and 60 Å occur at other temperatures, indicating that permittivity data near the phase transition can be used to identify the polytypes present in TlInS₂ crystals.Translated from Neorganicheskie Materialy, Vol. 40, No. 12, 2004, pp. 1423–1426.Original Russian Text Copyright © 2004 by Alekperov, Nadjafov     

On the resonance of acoustic waves in slightly deformed and slowly moving slabs

The stability is studied of acoustic waves generated by a time harmonic force in slabs described by: 0z1±g(x, y). By using a recently developed method, the exact solution of the Dirichlet problem is found for =0. It is shown that the solution is unstable against values of the frequency: =n,n. This is in agreement with the result already known in the literature, but found by other means. In a slightly deformed slab, 0<1, it is shown that stabilization of the resonant wave occurs at a time of order ^–. This is valid if the upper boundary is a concave surface. In case of a slab with slowly moving upper boundary, only the growth rate of the amplitude of the resonant wave is reduced. This holds for a non-oscillating motion of the upper boundary. In the case of an oscillating motion a further resonance is produced.     

The Accuracy of Dielectric Measurements in a Cylindrical Cavity H01p Resonator

The error of measurements of the dielectric parameters and tan in a cylindrical cavity resonator supporting the H _01p mode by varying the length of the resonator at a constant resonance frequency is considered. The errors in measuring and tanare investigated numerically as a function of the electric thickness of the sample being investigated and its permittivity .     

The Possibility of Reproducing the Units of Complex Permittivity at High Frequencies

The results of theoretical investigations of the reproduction of the units of the components of complex permittivity and by a method based on the use of the wave properties of a coaxial line are presented. The errors in reproducing and are analyzed.