层状锂离子电池正极材料LiNi0.8Co0.1Mn0.1O2的制备及性能

采用共沉淀法得到前驱体Ni0.8Co0.1Mn0.1(OH)2,利用前驱体与LiOH×H2O的高温固相反应得到高振实密度的锂离子电池层状正极材料LiNi0.8Co0.1Mn0.1O2 (2.3~2.5 g/cm3). 初步探讨了合成条件对材料电化学性能的影响. 通过X射线衍射(XRD)、扫描电镜(SEM)、热重-差热分析(TG/DTG)以及恒电流充放电测试对合成的样品进行了测试和表征. 结果表明,在750℃、氧气气氛下合成的材料具有较好的电化学性能. 通过XRD分析可知该材料为典型的六方晶系a-NaFeO2结构;SEM测试发现产物粒子是由500~800 nm的一次小晶粒堆积形成的二次类球形粒子. 电化学测试表明,其首次放电容量和库仑效率分别为168.6 mA×h/g和90.5%, 20次循环后容量为161.7 mA×h/g,保持率达到95.9%,是一种具有应用前景的新型锂离子电池正极材料.     

锂离子电池正极材料LiNi0.8Co0.2O2的研究

低成本、高比容量的LiNi0.8Co0.2O2是取代已商品化锂电池正极材料LiCoO2的候选材料。用工业原料,通过共沉淀法(pH=11 2±0 05)合成了β Ni0.8Co0.2(OH)2,将其和LiOH·H2O混合,在空气中先后于650℃和750℃烧结8h和20h,制得具有良好层状结构的LiNi0.8Co0.2O2。用合成的材料制备电池,在0 2C、3 0～4 1V进行充放电实验,其放电平台在3 8V以上,首次放电容量超过170mA·h/g,10次循环后,放电容量还能保持在164mA·h/g左右,且库仑效率达到96%以上。     

基于水热/溶剂热法制备不同形貌LiNi0.8Co0.1Mn0.1O2 锂离子电池正极材料

基于水热/溶剂热法制备LiNi_0.8Co_0.1Mn_0.1O₂电极材料,以镍、钴、锰乙酸盐为原料,以六亚甲基四胺为沉淀剂、水或乙醇为溶剂,通过调节溶剂组分控制Ni_0.8Co_0.1Mn_0.1（OH）₂（NCM）的成核与生长速率,从而合成两种形貌不同的Ni_0.8Co_0.1Mn_0.1（OH）₂前驱体,再经过混锂煅烧获得LiNi_0.8Co_0.1Mn_0.1O₂正极材料,研究比较了其电化学性能。以水为溶剂通过水热法合成的前驱体样品呈现出由一次片状颗粒紧密堆积组成的长方体状二次颗粒形貌,经混锂煅烧得到的产物表现出较高的放电比容量,在0.5C倍率下首次放电比容量可达到189.70 mA·h/g,循环200次容量保持率为69.72%。以乙醇为溶剂通过溶剂热法合成得到球形二次颗粒前驱体,最终得到的产物具有多孔球形结构,表现出了优异的循环性能,0.5C首次放电比容量为178.65 mA·h/g,循环200次容量保持率仍高达94.55%。     

锂离子电池正极材料LiNi0.8M0.2O2的制备

在增加氧气压力的条件下，采用固相反应制得一系列掺杂不同元素M的锂离子电池正极材料LiNi0.8M0.2O2. 研究发现，掺杂Al, Mn, Ti可以改善材料的耐过充性和循环性能，在充电电压为4.2~4.8 V的范围内循环3次，材料的放电容量没有显著的改变. X射线衍射和扫描电镜分析表明，掺杂Al, Mn, Ti提高了镍酸锂材料的六方菱型结构的有序性，维持了在充放电过程中的层状结构的稳定性. 其它掺杂元素降低了材料结构的有序性，影响了其电化学性能. 说明形成完整的晶体结构是掺杂元素的选择依据.     

微波共沉淀法制备锂离子电池正极材料LiNi0.8Co0.2O2

采用微波共沉淀法合成了制备LiNi0.8Co0.2O2的前驱体球形α-Ni0.8Co0.2(OH)2,将其与LiOH·H2O混合,在氧气氛围下,用不同的烧结温度分别烧结10小时获得LiNi0.8Co0.2O2正极材料。用XRD、SEM对所制备的正极材料进行结构和形貌分析,用恒流充放电测试材料的电化学性能。结果表明,烧结温度对材料结构和电化学性能影响较大,所合成材料均具有α-NaFeO2的层状结构,烧结温度越高材料结晶越完善。900℃烧结的LiNi0.8Co0.2O2材料初级颗粒结晶最完善而且其二次团聚粒子的平均粒径最小,其表现出的电化学性能也最好,首次放电容量为189.1mA·h·g-1,首次循环放电效率达到92.5%。30循环后放电容量保持在148 mA·h·g-1,显示出较好的循环稳定性。     

新型锂离子电池正极材料的制备及性能研究

锂离子电池的正极材料占据了高于40％的比例,材料性能对锂电池各项性能指标产生了直接影响。本文研究了一种新型锂离子电池,对电池正极材料的制备方法及性能进行了深入探讨。     

电解液添加剂PHS对LiNi0.8Mn0.1Co0.1O2锂离子电池性能的影响

以2-苯基-1-基1H-咪唑-1-磺酸酯(PHS)作为电解液添加剂,用于LiNi0.8Mn0.1Co0.1O2(NCM811)/石墨软包电池中.充放电测试和电化学测量的结果表明,PHS的添加可以提高NCM811/石墨软包电池的常温、低温和高温循环性能,令电池能够在-20～60°C的温度范围内工作,极大地提升了锂离子电池...     

锂离子电池正极材料LiNi1/2Co1/6Mn1/3O2的制备与性能

采用Co2+浓度递增的金属离子混合溶液分次共沉淀方法制备Ni1/2Co1/6Mn1/3(OH)2,以其为前驱体,通过高温固相反应得到具有Co含量梯度的层状LiNi1/2Co1/6Mn1/3O2,探讨了焙烧温度及Co含量梯度对材料的结构和电化学性能的影响. 通过X射线衍射、扫描电镜、热重分析及恒电流充放电测试对合成的样品进行了表征. 结果表明,700℃合成产物即具有类LiNiO2的六方层状结构,800和850℃合成产物阳离子排列有序度高,层状结构显著. 材料结晶度好,粒度均匀,粒径在亚微米级. 合成温度800℃的梯度材料具有最佳的电化学性能, 2.5~4.2 V, 0.1 C倍率充放电50次后,梯度材料的容量仍保持在171.2 mA×h/g. 相同的焙烧温度,梯度材料比均匀材料的电化学性能更加优异.     

锂离子电池正极材料的研究

锂离子电池具有高电压、高能量密度、大容量、长寿命等优点,可以循环性的使用。锂离子电池的使用对生态环境所造成的影响比较微弱,是当前我国电动汽车二次电池使用频率最高的一类。在锂离子电池中,正极材料是其重要的组成部分,正极材料的性能会直接影响锂离子电池自身的使用性能,同时还会影响到电池制备的成本费用,想要实现我国电动汽车产业化的目标,就需要注重锂离子电池正极材料研究工作的开展。不断地提升电化学性能,消除安全隐患。     

锂离子电池正极材料LiNi0.7Co0.25Al0.05O2的结构表征和电化学特性

用固相法制备球形LiNi0.7Co0.25Al0.05O2粉体,并综合研究该粉体的微观结构和电化学特性.用X射线衍射和透射电子选区衍射分析LiNi0.7Co0.25Al0.05O2的晶体结构.结果表明LiNi0.7Co0.25Al0.05O2为纯α-NaFeO2型六方晶结构.用扫描电镜观察二次颗粒的形状为球形.从循环伏安扫描实验中发现掺杂Al元素能够抑制LiNi0.7Co0.3O2在Li+插入-脱出过程中的结构相变,提高材料的循环稳定性.在电压为3.0～4.3 V,充放电倍率为C/5的条件下,LiNi0.7Co0.25Al0.05O2首次放电容量达到161.5 mA＠·h/g,30次循环后放电容量为156.1 mA·h/g,放电容量损失率仅为3.3%.     

Direct regeneration of LiNi0.5Co0.2Mn0.3O2 cathode material from spent lithium-ion batteries

At present, metal ions from spent lithium-ion batteries are mostly recovered by the acid leaching procedure, which unavoidably introduces potential pollutants to the environment. Therefore, it is necessary to develop more direct and effective green recycling methods. In this research, a method for the direct regeneration of anode materials is reported, which includes the particles size reduction of recovered raw materials by jet milling and ball milling, followed by calcination at high temperature after lithium supplementation. The regenerated LiNi_0.5Co_0.2Mn_0.3O₂ single-crystal cathode material possessed a relatively ideal layered structure and a complete surface morphology when the lithium content was n(Ni + Co + Mn):n(Li) = 1:1.10 at a sintering temperature of 920 ℃, and a sintering time of 12 h. The first discharge specific capacity was 154.87 mA·h·g^-1 between 2.75 V and 4.2 V, with a capacity retention rate of 90% after 100 cycles.     

Ultrathin-Y2O3-coated LiNi0.8Co0.1Mn0.1O2 as cathode materials for Li-ion batteries: Synthesis,performance and reversibility

Nickel-rich lithium material LiNi_xCo_yMn_1-x-yO₂(x > 0.6) becomes a new research focus for the next-generation lithium-ion batteries owing to their high operating voltage and high reversible capacity. However, the rate performance and cycling stability of these cathode materials are not satisfactory. Inspired by the characteristics of Y₂O₃ production, a new cathode material with ultrathin-Y₂O₃ coating was introduced to improve the electrochemical performance and storage properties of LiNi_0.8Co_0.1Mn_0.1O₂ for the first time. XRD, scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive spectroscopy (EDS) and XPS were used to mirror the crystal and surface of LiNi_0.8Co_0.1Mn_0.1O₂ particles, results i that a uniform interface formed on as-prepared material. The impacts on the electrochemical properties with or without Y₂O₃ coating are discussed in detail. Notably, galvanostatic discharge-charge tests appear that Y₂O_3-coated sample especially 3% coating displayed a better capacity retention rate of 91.45% after 100 cycles than the bare one of 85.07%.     

正极材料LiNi0.8Co0.1Mn0.1O2的合成工艺优化及电化学性能

采用高温固相法合成锂离子电池富镍三元材料LiNi_0.8Co_0.1Mn_0.1O₂,对其工艺条件进行优化,对产物进行X射线衍射（XRD（,扫描电镜（SEM（以及电化学性能分析。结果表明：在氧气气氛下,锂与金属元素摩尔比为1.05:1、烧结时间15 h、烧结温度750℃为最佳合成工艺条件。按最佳工艺合成的样品在1C首次放电容量高达174.9 mA·h·g^-1,50次循环后比容量为158.5 mA·h·g^-1,容量保持率为90.62%,表现出良好的循环稳定性。XRD和SEM表征表明,在氧气气氛下烧结的样品有良好的层状结构,阳离子混排程度小,具有较好的类球形,粒径均匀分布在10~20 μm。循环伏安（CV（和电化学阻抗（EIS（结果表明,工艺条件的优化有助于提高正极材料的电化学性能。     

Synthesis and characterization of mono-dispersion LiNi0.8Co0.1Mn0.1O2 micrometer particles for lithium-ion batteries

LiNi_0.8Co_0.1Mn_0.1O₂ cathode material for lithium-ion battery exhibits high capacity, but it suffers from interfacial side reactions and structural/thermodynamic instability, which leads to capacity reduction and safety problems. Cubic brick (Ni_0.8Co_0.1Mn_0.1)C₂O₄·2H₂O particles with micron size are synthesized by co-precipitation method. The oxalic precursor is sintered with lithium hydroxide to obtain cubic mono-dispersion LiNi_0.8Co_0.1Mn_0.1O₂ micrometer particles. Structural stability, cycling performance, rate capability and compacting density of the cubic mono-dispersion material are investigated. Conventional spherical and irregular mono-dispersion LiNi_0.8Co_0.1Mn_0.1O₂ are also prepared for comparison. The results reveal that the cubic mono-dispersion LiNi_0.8Co_0.1Mn_0.1O₂ dramatically enhances the structural stability and cycling performance at a little cost of capacity and rate capability.     

Enhanced electrochemical performance of ZrO2 modified LiNi0.6Co0.2Mn0.2O2 cathode material for lithium ion batteries

LiNi_0.6Co_0.2Mn_0.2O₂ (NCM622) cathode has been modified by incorporating ZrO₂ nanoparticles to improve its electrochemical performance. Compared to the pristine electrode, the cycling stability and rate capability of 0.5 wt% ZrO₂ modified-NCM622 have been improved significantly. The 0.5 wt% ZrO₂ modified-NCM622 cathode shows a capacity retention of 83.8% after 100 cycles at 0.1 C between 2.8 and 4.3 V, while that of the pristine NCM622 electrode is only 75.6%. When the current rate is set as 5C, the capacity retention of the 0.5 wt% ZrO₂-modified NCM622 is 10% higher than that of the pristine NCM622. Also, the rate capability of 0.5 wt% ZrO₂-modified NCM622 is better than that of the pristine NCM622 at various C-rates in a voltage range of 2.8–4.3 V. The enhanced electrochemical performances of the ZrO₂-modified NCM622 cathodes can be attributed to their high Li-ion conductivity and structural stability.     

Influence of oxygen percentage in calcination atmosphere on structure and electrochemical properties of LiNi0.8Co0.1Mn0.1O2 cathode material for lithium-ion batteries

Different calcination atmospheres of air, 50% oxygen (vs. N₂) and pure oxygen have been used to prepare special LiNi_0.8Co_0.1Mn_0.1O₂ cathode materials to observe the influence of oxygen composition. To investigate the structure and electrochemical property of the samples using different oxygen compositions, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), cycling performance tests and electrochemical impedance spectroscopy (EIS) were carried out. XRD, SEM, and XPS results show that the sample made using higher oxygen composition has less cation mixing and lower levels of Ni²⁺. However, both samples have almost the same oxygen environments on their surfaces as well as micro-morphology and size. The sample with a higher oxygen composition shows better electrochemical performance. Interestingly, the electrochemical performance of the sample made using 50% oxygen is similar to that made with pure oxygen and much better than the sample made with air. It has a specific capacity of 202.4 mAh g⁻¹ at 0.1C and a capacity retention of 85.2% after 300 cycles at 1C, which may be meaningful for balancing cost and performance.     

Influence of lithium difluorophosphate additive on the high voltage LiNi0.8Co0.1Mn0.1O2/graphite battery

Lithium-ion batteries (LIBs) possessing high energy densities are driven by the growing demands of electric vehicles (EVs) and hybrid electric vehicles (HEVs). One of the most effective strategies to improve the energy density of LIBs is to enlarge the charge cut-off voltage via a lithium salt additive for the conventional electrolyte system. Herein, lithium difluorophosphate (LIDFP) is employed to optimize and reconstruct the composition of the structure and interface for both cathode and anode, which can effectively restrain the oxidation decomposition of electrolyte as well as refrain the dissolve out of transition metals. The LiNi_0.8Co_0.1Mn_0.1O₂ (LNCM811)/graphite pouch cell with 1 wt% LIDFP in electrolyte delivers a discharge capacity retention of 91.3% at a high voltage of 4.4 V over 100 cycles, which is higher than the 82.0% of that without LIDFP additive. Additionally, the remaining capacity of LNCM811/C battery with 1 wt% LIDFP additive which is left at 60 °C for 14 days is 85.2%, and the recovery capacity is 93.3%. The LIDFP-containing electrolyte demonstrates a great application future for the LiBs operating under the high-voltage condition and high-temperature storage performance.     

LiAlO2-coated LiNi0.8Co0.1Mn0.1O2 and chlorine-rich argyrodite enabling high-performance all-solid-state lithium batteries at suitable stack pressure

All-solid-state lithium batteries (ASSLBs), which are consisted of Li_5.5PS_4.5Cl_1.5 electrolyte, metal lithium anode and LiNi_0.8Mn_0.1Co_0.1O₂ (NCM811) cathode, are speculated as a promising next generation energy storage system. However, the unstable oxide cathode/sulfide-based electrolyte interface and the dendrite formation in sulfide electrolyte using the lithium metal anode hinder severely commercialization of the ASSLBs. In this work, the dendrite formation in sulfide electrolyte is investigated in lithium symmetric cell by varying the stack pressure (3, 6, 12, 24 MPa) during uniaxial pressing, and uniformly nanosized LiAlO₂ buffer layer was carefully coated on NCM811 electrode (LiAlO₂@NCM811) to improve the cathode/electrolyte interface stability. The result shows that lithium symmetrical cell has a steady voltage evolution over 400 h under 6 MPa stacking pressure, and the assembled LiAlO₂@NCM811/Li_5.5PS_4.5Cl_1.5/Li battery under the stack pressure of 6 MPa exhibits large initial discharge specific capacity and excellent cycling stability at 0.05 C and 25 °C. The feasibility of using the lithium metal anode in all-solid-state batteries (ASSBs) under suitable stack pressure combined with uniformly nanosized LiAlO₂ buffer layer coated on NCM811 electrode supply a facile and effective measures for constructing ASSLBs with high energy density and high safety.     

层状结构Li[Ni,Co,Mn]O2正极材料制备与改性研究进展

介绍了层状结构的Li[Ni,Co,Mn]O2作为锂离子电池正极材料具有良好发展潜力,制备过程与条件对Li[Ni,Co,Mn]O2的结构、性能与生产成本有重要的影响,表面修饰与改性是进一步提高其性能和稳定性的重要途径。归纳了Li[Ni,Co,Mn]O2正极材料的各种制备方法,并对各种改性方法进行比较。分析了层状结构Li[Ni,Co,Mn]O2正极材料存在的问题和今后的研究重点。     

锂离子电池聚合物正极材料研究进展

高储能的锂电池聚合物正极材料是近年来新型电化学能源研究发展的热点。本文综述了自由基聚合物、导电聚合物、有机多硫聚合物以及多骨架碳硫交联聚合物正极材料的结构、制备、导电机理和电化学性能。重点介绍了自由基聚合物氮氧结构的特点和快速充放电性能,导电聚合物的合成方法和掺杂机理,以及有机多硫聚合物和多骨架碳硫交联聚合物中—(S—S)n—键的高效储能特性和超高比容量性质。最后提出了解决聚合物材料容量的衰减和易降解性以保证稳定的循环性能以及完善合成及制备工艺是未来的研究重点。