Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

Pyroelectric properties of BST/PLT composite thick films with addition of xPbO–(1 − x)B2O3 glass

The Ba_xSr_1−xTiO₃ (BST)/Pb_1−xLa_xTiO₃ (PLT) composite thick films (20 μm) with 12 mol% amount of xPbO–(1 − x)B₂O₃ glass additives (x = 0.2, 0.35, 0.5, 0.65 and 0.8) have been prepared by screen-printing the paste onto the alumina substrates with silver bottom electrode. X-ray diffraction (XRD), scanning electron microscope (SEM) and an impedance analyzer and an electrometer were used to analyze the phase structures, morphologies and dielectric and pyroelectric properties of the composite thick films, respectively. The wetting and infiltration of the liquid phase on the particles results in the densification of the composite thick films sintered at 750 °C. Nice porous structure formed in the composite thick films with xPbO–(1 − x)B₂O₃ glass as the PbO content (x) is 0.5 ≥ x ≥ 0.35, while dense structure formed in these thick films as the PbO content (x) is 0.8 ≥ x ≥ 0.65. The volatilization of the PbO in PLT and the interdiffusion between the PLT and the glass lead to the reduction of the c-axis of the PLT phase. The operating temperature range of our composite thick films is 0–200 °C. At room temperature (20 °C), the BST/PLT composite thick films with 0.35PbO–0.65B₂O₃ glass additives provided low heat capacity and good pyroelectric figure-of-merit because of their porous structure. The pyroelectric coefficient and figure-of-merit F_D are 364 μC/(m² K) and 14.3 μPa^−1/2, respectively. These good pyroelectric properties as well as being able to produce low-cost devices make this kind of thick films a promising candidate for high-performance pyroelectric applications.     

Synthesis, phase transformation and dielectric properties of sol–gel derived Bi2Ti2O7 ceramics

Sol–gel derived Bi₂Ti₂O₇ ceramic powders have been prepared from methoxyethoxides of bismuth and titanium (molar ratio of Ti/Bi = 1.23 and water/alkoxides = 1.31). The Bi₂Ti₂O₇ phase was stable at a low temperature (700 °C), but it then transformed into mixed phases of Bi₄Ti₃O₁₂ and Bi₂Ti₄O₁₁ at 850–1150 °C. The single phase of Bi₂Ti₂O₇ reoccurred at 1200 °C. Dielectric properties and ferroelectric behavior of samples sintered at 1150 and 1200 °C were examined. Under frequency of 1 MHz, samples sintered at 1150 and 1200 °C had a dielectric constant of 101.3 and 104.2, and a loss tangent of 0.0193 and 0.0145, respectively. Only the sample sintered at 1150 °C showed ferroelectric behavior, where remanent polarization is 3.77 μC cm⁻² and coercive field is 24 kV cm⁻¹. Thus, the Bi₂Ti₂O₇ did not exhibit ferroelectricity, but the mixed phase of Bi₄Ti₃O₁₂ and Bi₂Ti₄O₁₁ did.     

Infrared optical properties of Bi2Ti2O7 thin films by spectroscopic ellipsometry

Bi₂Ti₂O₇ thin films have been grown directly on n-type GaAs (1 0 0) by the chemical solution decomposition technique. X-ray diffraction analysis shows that the Bi₂Ti₂O₇ thin films are polycrystalline. The optical properties of the thin films are investigated using infrared spectroscopic ellipsometry (3.0–12.5 μm). By fitting the measured ellipsometric parameter (Ψ and Δ) data with a three-phase model (air/Bi₂Ti₂O₇/GaAs), and Lorentz–Drude dispersion relation, the optical constants and thickness of the thin films have been obtained simultaneously. The refractive index and extinction coefficient increase with increasing wavelength. The fitted plasma frequency ω_p is 1.64×10¹⁴ Hz, and the electron collision frequency γ is 1.05×10¹⁴ Hz, and it states that the electron average scattering time is 0.95×10⁻¹⁴ s. The absorption coefficient variation with respect to increasing wavelength has been obtained.     

Bi2O3助熔剂对CaO-B2O3-SiO2/Al2O3玻璃陶瓷复合材料性能的影响

以CaO-B₂O₃-SiO₂(CBS)玻璃粉体和Al₂O₃陶瓷粉体为原料,通过在CBS与Al₂O₃的质量比固定为50:50的玻璃-陶瓷复合材料中添加适量的Bi₂O₃作为烧结助熔剂,探讨了Bi₂O₃助熔剂对CBS/Al₂O₃复合材料的烧结性能、介电性能、抗弯强度和热膨胀系数的影响规律.研究表明:Bi₂O₃助熔剂能通过降低CBS玻璃的转变温度和黏度促进CBS/Al₂O₃复合材料的致密化进程,于880 ℃下烧结即能获得结构较致密、气孔较少的CBS/Al₂O₃复合材料.然而,过量添加Bi₂O₃将使玻璃的黏度过低,从而恶化CBS/Al₂O₃复合材料的烧结性能、介电性能及抗弯强度.当Bi₂O₃的添加量为CBS/Al₂O₃复合材料的1.5wt%时,于880 ℃下烧结即能获得最为致密的CBS/Al₂O₃复合材料,密度为2.82 g·cm^-3,这一材料具有良好的介电性能(介电常数为7.21,介电损耗为1.06×10^-3),抗弯强度为190.34 MPa,0~300 ℃的热膨胀系数为3.52×10^-6 K^-1.     

High-resolution and analytical transmission electron microscopy of epitaxial YBa2Cu3O7−x thin films and YBa2Cu3O7/PrBa2Cu3O7 superlattices

Transmission electron microscopy (TEM) studies of epitaxial YBa₂Cu₃O_7−x thin films and YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices are summarized. High-resolution imaging of cross-sections and plan views and energy-dispersive X-ray microanalysis and electron energy loss spectroscopy in the transmission electron microscope were the methods applied. In the first section results on YBa₂Cu₃O_7−x thin films With varying oxygen stoichiometry deposited onto SrTiO₃ are discussed. Then, YBa₂Cu₃O₇/PrBa₂Cu₃O₇ superlattices deposited onto SrTiO₃ and MgO are investigated. Finally, an interface analysis of high-quality YBa₂Cu₃O_7−x thin films deposited onto sapphire with yttrium-stabilized zirconia buffer layers is presented.     

Crystal growth and spectral properties of pure and Co-doped Mg3B2O6 crystal

Novel pure and cobalt-doped magnesium borate crystals (Mg₃B₂O₆) have been grown successfully by the Czochralski technique for the first time. Crystal growth, X-ray powder diffraction (XRD) analysis, absorption spectrum, fluorescence spectrum as well as fluorescence decay curve of Co²⁺:Mg₃B₂O₆ (MBO) were described. From the absorption peaks for the octahedral Co²⁺ ions, the crystal-field parameter Dq and the Racah parameter B were estimated to be 943.3 cm⁻¹ and 821.6 cm⁻¹, respectively. The fluorescence lifetime of the transition ⁴T₁(⁴P) → ⁴T₂ centered at 717 nm was measured to be 9.68 ms.     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Optical properties of a-(Se70Te30)100−x(Se98 Bi2)x thin films

Measurements of optical constants (absorption coefficient, refractive index, extinction coefficient, real and imaginary part of the dielectric constant) have been made on a-(Se₇₀Te₃₀)_100−x (Se₉₈Bi₂)_x thin films (where x=0, 5, 10, 15 and 20) of thickness 2000 Å in the wavelength range 450–1000 nm. It is found that the optical bandgap decreases with the increase of Se₉₈Bi₂ concentration in the a-(Se₇₀Te₃₀)_100−x(Se₉₈Bi₂)_x system. The value of refractive index (n) decreases, while the extinction coefficient (k) increases with increasing photon energy. The results are interpreted in terms of concentration of localized states varying effective Fermi level.     

Investigation in the VUV range of the excitation efficiency of the Tb ion luminescence in Y3 (Alx, Gay)5O12 host lattices

VUV excitation spectra of the visible luminescence of Tb³⁺ activated Y₃(Al_x, Ga_y)₅O₁₂ compounds and their diffuse reflectance spectra are presented. The crystal field strength, the absorption threshold of the matrix and the external quantum efficiency (Q_ext) associated with the different excitation mechanisms (4f⁸ → 4f⁷ 5d transitions in the activator or interband transitions in the host) decrease when the gallium concentration increases. Such variations are ascribed to an increase of the oxidizing character of the host matrix along with the gallium concentration. The decrease of the external quantum efficiency (Q_ext) is discussed in terms of a trivalent rare-earth ion (RE³⁺) configurational coordinate model and related to the intervention of the photoionized state [RE³⁺ → RE⁴⁺ + e⁻]. The non radiative relaxation rate increases when this state is stabilized.affd     

Microstructures, densification and mechanical properties of TiC–Al2O3–Al composite by field-activated combustion synthesis

Dense TiC–Al₂O₃–Al composite was prepared with Al, C and TiO₂ powders by means of electric field-activated combustion synthesis and infiltration of the molten metal (here Al) into the synthesized TiC–Al₂O₃ ceramic. An external electric field can effectively improve the adiabatic combustion temperature of the reactive system and overcome the thermodynamic limitation of reaction with x < 10 mol. Thereby, it can induce a self-sustaining combustion synthesis process. During the formation of Al₂O₃–TiC–Al composite, Al is molten first, and reacted with TiO₂ to form Al₂O₃, followed by the formation of TiC through the reaction between the displaced Ti and C. Highly dense TiC–Al₂O₃–Al with relative density of up to 92.5% was directly fabricated with the application of a 14 mol excess Al content and a 25 V cm⁻¹ field strength, in which TiC and Al₂O₃ particles possess fine-structured sizes of 0.2–1.0 μm, with uniform distribution in metal Al. The hardness, bending strength and fracture toughness of the synthesized TiC–Al₂O₃–Al composite are 56.5 GPa, 531 MPa and 10.96 MPa m^1/2, respectively.     

Microwave dielectric characteristics of Ba(Mg1/3Ta2/3)O3 ceramics sintered at low-temperatures

The microwave dielectric properties and microstructures of Ba(Mg_1/3Ta_2/3)O₃ (BMT) ceramics sintered at low temperatures with 2–3 wt.% NaF additives were investigated. BMT ceramics sintered at 1340 °C for 3–12 h showed dielectric constants (_r) of 25.5–25.7, Qf values of 41 500–50 400 GHz and temperature coefficients of the resonator frequency (τ_f) of 10.9–21.4 ppm °C⁻¹. The variation of sintering time almost had no effect on the dielectric constant. The Qf value increased and the τ_f decreased with increasing sintering time. The ordering degree of Mg²⁺ and Ta⁵⁺ at B-sites increased with increasing sintering time.     

Structural and optical properties of (100 − x)(Li2B4O7) − x(SrO–Bi2O3–0.7Nb2O5–0.3V2O5) glasses and glass nanocrystal composites

Glasses of various compositions in the system (100 − x)(Li₂B₄O₇) − x(SrO–Bi₂O₃–0.7Nb₂O₅–0.3V₂O₅) (10  x  60, in molar ratio) were prepared by splat quenching technique. The glassy nature of the as-quenched samples was established by differential thermal analyses (DTA). The amorphous nature of the as-quenched glasses and crystallinity of glass nanocrystal composites were confirmed by X-ray powder diffraction studies. Glass composites comprising strontium bismuth niobate doped with vanadium (SrBi₂(Nb_0.7V_0.3)₂O_9−δ (SBVN)) nanocrystallites were obtained by controlled heat-treatment of the as-quenched glasses at 783 K for 6 h. High resolution transmission electron microscopy (HRTEM) of the glass nanocrystal composites (heat-treated at 783 K/6 h) confirm the presence of rod shaped crystallites of SBVN embedded in Li₂B₄O₇ glass matrix. The optical transmission spectra of these glasses and glass nanocrystal composites of various compositions were recorded in the wavelength range 190–900 nm. Various optical parameters such as optical band gap (E_opt), Urbach energy (ΔE), refractive index (n), optical dielectric constant and ratio of carrier concentration to the effective mass (N/m^*) were determined. The effects of composition of the glasses and glass nanocrystal composites on these parameters were studied.     

Influence of A-site nonstoichiometry on sintering, microstructure and electrical properties of (Bi0.5Na0.5)TiO3 ceramics

Lead-free (Bi_0.5Na_0.5)_1+xTiO₃ ceramics (x = −0.02, −0.01, −0.005, 0, 0.005 and 0.01) were prepared by ordinary sintering. The effect of A-site stoichiometry on the densification, microstructure, dielectric properties, high-temperature impedances, and piezoelectric properties was explored. It was found that the high conductivity of (Bi_0.5Na_0.5)TiO₃ (BNT) ceramics should be mainly attributed to the formation of A-site cation vacancies during sintering. Improved physical and electrical properties can be achieved in the sample with A-site cation excess. The control of the stoichiometry proves to be an effective way to improve BNT ceramics for possible application.     

Hydrothermal synthesis, crystal structure and thermal stability of Ba-titanate nanotubes with layered crystal structure

BaTi₃O₇·nH₂O nanotubes have been synthesized through a hydrothermal reaction between Na-rich trititanate nanotubes and Ba(OH)₂ within the pH range 12–8.2. These nanotubes possess the same layered crystal structure of the precursor Na_2−xH_xTi₃O₇·nH₂O. They also keep the morphology of their precursor Na-trititanate nanotubes used in the synthesis, having an external diameter of 20–25 nm. The BaTi₃O₇·nH₂O nanotubes remained fully stable up to 300 °C, while nanotubular form continues to exist up to 600 °C, together with amorphous particles.     

Synthesis, structure refinement and characterization of tetrahydrated acid gadolinium diphosphate HGdP2O7·4H2O

Synthesis and single crystal structure are reported for a new gadolinium acid diphosphate tetrahydrate HGdP₂O₇·4H₂O. This salt crystallizes in the monoclinic system, space group P2₁/n, with the following unit-cell parameters: a = 6.6137(2) Å, b = 11.4954(4) Å, c = 11.377(4) Å, β = 87.53(2)° and Z = 4. Its crystal structure was refined to R = 0.0333 using 1783 reflections. The corresponding atomic arrangement can be described as an alternation of corrugated layers of monohydrogendiphosphate groups and GdO₈ polyhedra parallel to the () plane. The cohesion between the different diphosphoric groups is provided by strong hydrogen bonding involving the W4 water molecule.

IR and Raman spectra of HGdP₂O₇·4H₂O confirm the existence of the characteristic bands of diphosphate group in 980–700 cm⁻¹ area. The IR spectrum reveals also the characteristic bands of water molecules vibration (3600–3230 cm⁻¹) and acidic hydrogen ones (2340 cm⁻¹). TG and DTA investigations show that the dehydration of this salt occurs between 79 and 900 °C. It decomposes after dehydration into an amorphous phase. Gadolinium diphosphate Gd₄(P₂O₇)₃ was obtained by heating HGdP₂O₇·4H₂O in a static air furnace at 850 °C for 48 h.     

Doping and electrical characteristics of in-situ heavily B-doped Si1−x−yGexCy films epitaxially grown using ultraclean LPCVD

Doping and electrical characteristics of in-situ heavily B-doped Si_1−x−yGe_xC_y (0.22<x<0.6, 0<y<0.02) films epitaxially grown on Si(100) were investigated. The epitaxial growth was carried out at 550°C in a SiH₄–GeH₄–CH₃SiH₃–B₂H₆–H₂ gas mixture using an ultraclean hot-wall low-pressure chemical vapor deposition (LPCVD) system. It was found that the deposition rate increased with increasing GeH₄ partial pressure, and only at high GeH₄ partial pressure did it decrease with increasing B₂H₆ as well as CH₃SiH₃ partial pressures. With the B₂H₆ addition, the Ge and C fractions scarcely changed and the B concentration (C_B) increased proportionally. The C fraction increased proportionally with increasing CH₃SiH₃ partial pressures. These results can be explained by the modified Langmuir-type adsorption and reaction scheme. In B-doped Si_1−x−yGe_xC_y with y=0.0054 or below, the carrier concentration was nearly equal to C_B up to approximately 2×10²⁰ cm⁻³ and was saturated at approximately 5×10²⁰ cm⁻³, regardless of the Ge fraction. The B-doped Si_1−x−yGe_xC_y with high Ge and C fractions contained some electrically inactive B even at the lower C_B region. Resistivity measurements show that the existence of C in the film enhances alloy scattering. The discrepancy between the observed lattice constant and the calculated value at the higher Ge and C fraction suggests that the B and C atoms exist at the interstitial site more preferentially.     

Frequency dependent electrical conductivity and dielectric relaxation behavior in amorphous (90V2O5–10Bi2O3) oxide semiconductors doped with SrTiO3

We report on the experimental results of frequency dependent a.c. conductivity and dielectric constant of SrTiO₃ doped 90V₂O₅–10Bi₂O₃ semiconducting oxide glasses for wide ranges of frequency (500–10⁴ Hz) and temperature (80–400 K). These glasses show very large dielectric constants (10²–10⁴) compared with that of the pure base glass (≈10²) without SrTiO₃ and exhibit Debye-type dielectric relaxation behavior. The increase in dielectric constant is considered to be due to the formation of microcrystals of SrTiO₃ and TiO₂ in the glass matrix. These glasses are n-type semiconductors as observed from the measurements of the thermoelectric power. Unlike many vanadate glasses, Long's overlapping large polaron tunnelling (OLPT) model is found to be most appropriate for fitting the experimental conductivity data, while for the undoped V₂O₅–Bi₂O₃ glasses, correlated barrier hopping conduction mechanism is valid. This is due to the change of glass network structure caused by doping base glass with SrTiO₃. The power law behavior (σ_ac=A(ω^s) with s<1) is, however, followed by both the doped and undoped glassy systems. The model parameters calculated are reasonable and consistent with the change of concentrations (x).     

In situ co-precipitation synthesis and photoluminescence of YxGd1−xVO4:Tm microcrystalline phosphors by hybrid precursors

Y_xGd_1−xVO₄:Tm³⁺ (5 mol%) phosphors were prepared by in situ co-precipitation technology with the different content ratio of Y/Gd (x = 0.2, 0.3, 0.4, 0.5, 0.6, 0.8, respectively). During the process, rare earth coordination polymers with o-hydroxylbenzoate were used as precursors, composing with polyethylene glycol (PEG) as dispersing media. After heat-treatment of the resulting multicomponent hybrid precursors at 900 °C, the samples were obtained. SEM indicated the particles present good crystalline state, whose crystalline grain sizes were about 0.2–2 μm. Under the excitation of 257 nm, all the materials show the characteristic emission of Tm³⁺ which is the strong blue emission centered at 475 nm originating from ¹G₄ → ³H₆ of Tm³⁺. Besides this, concentration quenching appears in the system of YVO₄:Tm³⁺ and GdVO₄:Tm³⁺. And when x reaches 0.5, the system of Y_xGd_1−xVO₄:Tm³⁺ shows the strongest blue emission.     

Ferroelectric, dielectric and piezoelectric properties of potassium lanthanum bismuth titanate K0.5La0.5Bi4Ti4O15 ceramics

The Aurivillius type bismuth layer-structured compound potassium lanthanum bismuth titanate (K_0.5La_0.5Bi₄Ti₄O₁₅) is synthesized using conventional solid-state processing. The phase analysis is performed by X-ray diffraction (XRD) and the microstructural morphology is conducted by scanning electron microscopy (SEM). The ferroelectric, dielectric and piezoelectric properties of K_0.5La_0.5Bi₄Ti₄O₁₅ (KLBT) ceramics are investigated in detail. The remnant polarization (P_r) and coercive field (E_c) are found to be 8.6 μC cm⁻² and 60 kV cm⁻¹, respectively. The Curie temperature T_c and piezoelectric coefficient d₃₃ are 413 °C and 18 pC N⁻¹, respectively.