HL-1装置的物理调试(1985)

自1985年4月起正式开展HL-1装置的物理调试,其目的是获得平衡、稳定和比较干净的等离子体,并在此基础上开展初步的物理实验研究。在纵向磁场2.3T下获得等离子体电流135kA,平顶时间150-200ms。等离子体电流的持续时间出乎意料地长达1s,其详细的物理原因尚待深入研究。其它等离子体参数的初步结果为n_e≈ 2.8×10~(13)cm~(-3),T_e≈350-500eV,τ_E≈10ms。     

中国环流器二号A装置(HL-2A)工程研制

中国环流器二号A装置(HL 2A)(设计指标:大半径1.65m、小半径0 4m、环向磁场2 8T、环向等离子体电流480kA)是我国已建成的第一个偏滤器托卡马克实验型磁约束聚变装置。HL 2A装置的首要研究目标是利用其独特的大体积极向偏滤器在高参数等离子体条件下开展与偏滤器位形运行有关的研究。本文总结了HL 2A装置工程设计、制造与安装、工程调试等研制的主要内容和关键技术。工程调试和初步物理实验的结果表明:HL 2A装置的主要工程参数和性能已具备开展物理实验的条件,并已成功地运行于偏滤器位形。2003年11月底,HL 2A装置获得等离子体电流168kA,等离子体存在时间920ms,等离子体线平均密度1.7×1019m-3,环向磁场1 4T,极限真空度为4.6×10-6Pa。     

ITER装置中等离子体旋转和反馈控制对电阻壁模影响的数值研究

在托卡马克等离子体中,电阻壁模是非常重要的磁流体不稳定性,特征时间在毫秒量级.对长时间稳态运行下的先进托卡马克,电阻壁模限制着聚变装置的运行参数空间(放电时间和比压),影响经济效益,所以研究电阻壁模稳定性至关重要.本文使用MARS程序,针对ITER装置上9 MA先进运行平衡位形,研究了等离子体旋转和反馈控制对电阻壁模的影响.结果表明,在没有反馈控制时,当比压参数Cβ取0.7,等离子体环向旋转频率达到1.1%的阿尔芬频率时,可以完全稳定电阻壁模;在等离子体环向旋转和反馈控制共同作用时,比压参数Cβ取0.7,反馈增益|G|取0.6时,稳定电阻壁模所需要的等离子体旋转频率为0.2%的阿尔芬频率.可见,单独靠等离子体环向旋转稳定电阻壁模所需的旋转频率较大;而等离子体环向旋转和反馈控制共同作用可以降低稳定电阻壁模的旋转频率临界值,符合先进托卡马克的运行.本文的研究结果对中国聚变工程试验堆CFETR的工程设计和运行具有一定指导意义.     

托卡马克微波预电离等离子体

使用回旋管系统产生的电子回旋波段的大功率微波在托卡马克中得到无电流等离子体。其电子密度达8×10¹²cm^-3,电子温度达50eV,粒子约束时间约为0.5ms,加热效率达25％以上。研究了对环向击穿的影响及加热机制。     

等离子体的静态稳定性

本文讨论了外磁场微小的变动对等离子体平衡位形的影响,即等离子体的静态稳定性问题。指出,只有当附加磁场与等离子体接近不稳定边界的模相耦合时,才可能引起平衡位形很大的变化。由此,我们分析了杂散场对环电流器(托克马克)的影响。     

自约束球形等离子体的平衡与稳定性

本文用磁流体力学的概念,解释并证实了在环境压力P₀中确可存在平衡且稳定的球形等离子体。同时发现在自约束的等离子体平衡态不可能是无力场位形。还证明自约束的球状等离子体平衡态不唯一。计算结果表明,等离子体火球内部的压力P小于环境压力P₀,与球形马克的磁场形态比较后发现自约束等离子体火球中的磁轴向中心偏移约10％,磁场的剪切稍弱。用Mercier判据可初步得知自约束球形等离子体平衡态是关于局域模稳定的。 关键词：     

CT-6托卡马克研究(Ⅰ) 实验装置的研制和调试

托卡马克是一种产生高温环形等离子体的聚变实验装置,也是一类复杂的现代化的电物理装备。CT-6是我国首先投入运行的小型托卡马克装置,其主要参数为:大半径45cm;小半径9.2cm;环向磁场2TL;等离子电流30kA;经过调试阶段,达到了预期目标,产生了平衡、稳定的电子温度为250eV左右的环形高温等离子体。CT-6由电磁系统(包括环向场、涡旋场、平衡场)、超高真空系统(包括环形真空室和抽气机组)、电源控制系统和诊断测量系统等部份组成,它是由中国科学院物理研究所、电工研究所及其他许多单位协作研制成功的。 本文描述CT-6装置的设计、结构、工程研制和调试过程,以及有关的试验结果。     

HL-2A托卡马克上的边缘局域模特性初步研究

高约束模式(H模)下自发产生的边缘局域模(ELM),虽然利于控制等离子体密度和排出杂质粒子从而实现H模放电的稳态运行,但是ELM爆发携带的大量粒子和能量会对装置的第一壁材料造成很大的损坏,所以在下一代聚变装置上使用之前很多装置已经开始了对ELM的研究.在HL-2A装置上观察到了不同的ELM,扰动幅度小的ELM引起的等离子体储能损失小于3%,ELM之间的时间间隔约为3 ms,表现出Ⅲ型ELM的特征;扰动幅度较大的ELM的爆发对等离子体电流、等离子体密度及储能都有很明显的扰动,对等离子体储能的扰动大于10%,ELM爆发的频率随通过等离子体磁分界面的净加热功率的增加而增加,表现出明显的Ⅰ型ELM的特征.ELM先兆有不对称性,在弱场侧磁探针信号能观测到,但强场侧却观测不到;ELM先兆的频率约为45 kHz,观测到的最长的先兆先于ELM前约10ms出现.     

J-TEXT装置纵场电源系统及其调试

J-TEXT装置的纵场磁体是由十六个近似圆形的常规铜线圈串联而成。纵场电源系统需要为纵场磁体提供最大电流为160kA、平顶时间为500ms的准梯形电流波形,以在等离子体中心产生最大为3T的磁场。基于原TEXT-U纵场电源的电路结构,重新设计和改造了电源的控制系统和保护系统。目前,纵场电源系统已经通过了测试,在J-TEXT装置首轮放电运行中,该系统可输出92.5kA的平顶电流,在等离子体中心产生了约1.74T的磁场。     

CT-6托卡马克研究(Ⅰ)——实验装置的研制和调试

托卡马克是一种产生高温环形等离子体的聚变实验装置,也是一类复杂的现代化的电物理装备。CT-6是我国首先投入运行的小型托卡马克装置,其主要参数为:大半径45cm;小半径9.2cm;环向磁场2TL;等离子电流30kA;经过调试阶段,达到了预期目标,产生了平衡、稳定的电子温度为250eV左右的环形高温等离子体。CT-6由电磁系统(包括环向场、涡旋场、平衡场)、超高真空系统(包括环形真空室和抽气机组)、电源控制系统和诊断测量系统等部份组成,它是由中国科学院物理研究所、电工研究所及其他许多单位协作研制成功的。本文描述CT-6装置的设计、结构、工程研制和调试过程,以及有关的试验结果。 关键词：     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.     

A novel methodology for photometric compensation of projection display on patterned screen

We propose a novel methodology based on the projector-camera (ProCam) system to address the photometric compensation issue for the projection display on the patterned screen.The patterned screen is treated as the combination of a perfect white screen and a color modulator.The perfect white screen is used to automatically and accurately characterize the ProCam system offline using the polynomial model,and the parameters of the color modulator can be efficiently recovered by employing only two gray images based on the linear reflectance model.The experimental results show that the color artifacts of the display image can be greatly improved with this methodology,which demonstrates its feasibility and validity in the photometric compensation.