γ-Fe2O3抗As2O3中毒能力的分子模拟

采用密度泛函理论研究了γ-Fe₂O₃表面As₂O₃的吸附以及掺杂改性提高抗As₂O₃中毒性能的作用机理.计算了As₂O₃在完整以及O缺陷γ-Fe₂O₃（001）表面的吸附性能,包括吸附位点、吸附结构、吸附能、PDOS等.同时建立了Mo、Ti、Mg掺杂的γ-Fe₂O₃模型,探讨了助剂掺杂对抗砷中毒能力的作用机制,并考虑了掺杂量的影响.结果表明：As₂O₃倾向于以O端化学吸附在γ-Fe₂O₃（001）表面Fe_oct位,吸附过程发生强烈的相互作用和电荷转移.当表面存在O缺陷时,As₂O₃的吸附能得到提高.Mo、Ti、Mg倾向于掺杂在Fe_oct位,增强了对As₂O₃的吸附能力,并且增大Mo的掺杂量可以强化As₂O₃的吸附.As₂O₃倾向于与活性较强的Mo、Ti、Mg发生反应,从而保护活性Fe位不受砷中毒,Ti和Mg的掺杂还抑制了相邻Fe位对As₂O₃的吸附.Mo、Ti、Mg的掺杂还促进了催化剂表面对NH₃的吸附,增强了表面酸性强度,有利于SCR反应.Mo、Ti、Mg原子的掺杂有利于提高γ-Fe₂O₃催化剂的抗砷中毒性能.     

CuO(-CeO2)/Al2O3催化剂对萘催化氧化性能研究

采用浸渍法制备了CuO/Al2O3、CeO2/Al2O3和CuO-CeO2/Al2O3这3种催化剂,通过氮吸附、SEM、XRD等手段对催化剂的结构及组成进行了表征,利用固定床反应装置考察了活性组分、气体流量、催化反应温度对萘催化氧化性能的影响.结果表明,18%CeO2/Al2O3的萘催化活性较低,18%CuO/Al2O3和9%CuO-9%CeO2/Al2O3的活性较高,两者在300℃时对萘的去除率分别达到91%和89%;CuO-CeO2/Al2O3催化剂具有比CuO/Al2O3更好的低温活性;气流量的变化对两种催化剂性能的影响不大.     

CuO-Ru/Al2O3 催化臭氧化降解苯乙酮的研究

采用浸渍法制备了以活性Al2O3为载体的双组分催化剂CuO-Ru/Al2O3,利用该催化剂催化臭氧化降解了苯乙酮.结果表明,贵金属钌掺杂能显著提高CuO/Al2O3催化臭氧化苯乙酮的降解效率,如在相同条件下处理30 min后,单独臭氧氧化、CuO/Al2O3/O3和CuO-Ru/Al2O3/O3对苯乙酮水溶液的COD去除率分别为6.3%、20.0%和54.0%.pH对CuO-Ru/Al2O3催化臭氧化降解苯乙酮的效率并没有影响,但与单独臭氧化相比,该催化臭氧化体系更适合在中性或酸性条件下应用.CuO-Ru/Al2O3对水中臭氧有较好的催化分解活性,臭氧分解的速率常数达2.58×10-3s-1,高于二次水中臭氧的分解速率常数1.19×10-3s-1.叔丁醇的试验结果表明,CuO-Ru/Al2O3/O3降解苯乙酮反应遵循羟基自由基(.OH)反应机制.     

富氧条件下在Ag/Al2O3催化剂上C3H6选择性还原NO

比较富氧条件下,Ｃ₃Ｈ₆ 在溶胶－凝胶和浸渍２种方法制备的Ａｇ／Ａｌ₂Ｏ₃ 催化剂上还原ＮＯ的活性和热稳定性． 结果表明,从活性角度考虑,采用溶胶－凝胶法制备Ａｇ／Ａｌ₂Ｏ₃ 催化剂时,最佳Ａｇ 负载量（ｗｔ）为４％ ～６％ ,其最大活性与浸渍法制备的２％ Ａｇ／Ａｌ₂Ｏ₃ 催化剂相同,而溶胶－凝胶法制备的催化剂有更宽的活性温度范围． 随着焙烧温度提高,溶胶－凝胶法制备的Ａｇ／Ａｌ₂Ｏ₃ 催化剂的比表面和活性下降比浸渍法慢．此外,还考察了气氛中含有ＣＯ对Ａｇ／Ａｌ₂Ｏ₃ 催化剂活性的影响,结果表明活性降低,其原因可能是活性高的氧化态Ａｇ 被ＣＯ部分还原为活性低的还原态Ａｇ．     

Al2O3催化臭氧化处理邻苯二甲酸二甲酯

'Al₂O₃催化剂对邻苯二甲酸二甲酯(DMP)溶液臭氧化过程的影响结果表明:Al₂O₃可以显著提高臭氧氧化的效果,反应120min后,TOC的去除率从单独臭氧氧化的23.9%提高到55.1%.实验中还考察了制备条件对Al₂O₃催化剂活性的影响并确定了反应的最佳工艺条件.在实验考察的范围内:焙烧温度600℃,Al₂O₃粒径为0.5～1.0mm时催化活性最高;最佳反应工艺条件为:催化剂投加量20g/L,混和气体流速200mL/min,反应温度15℃.通过单独臭氧氧化,单独臭氧氧化后再进行催化剂吸附,催化臭氧化的对比实验证明了Al₂O₃催化剂对体系TOC的去除主要是基于催化作用.     

MnO2/Al2O3催化剂-微气泡臭氧体系催化降解喹啉及其机理

制备了纳米MnO₂,并以Al₂O₃为载体制备了掺杂型MnO₂/Al₂O₃颗粒催化剂.催化剂焙烧温度和时间分别为500℃和4 h、MnO₂质量分数为8%时,催化剂具有最高的臭氧催化氧化活性.SEM分析表明,纳米MnO₂均匀分布于Al₂O₃载体表面.MnO₂/Al₂O₃催化剂的比表面积（BET）为183.22 m²·g^-1,平均孔容为0.27 cm³·g^-1,平均孔径为4.87 nm.建立了MnO₂/Al₂O₃催化剂-微气泡臭氧催化反应体系,研究了该体系对喹啉的降解去除效果及其机理.臭氧微气泡的平均粒径为61.7 μm.微气泡臭氧投量为30 mg·L^-1时,反应60 min后喹啉去除率能达到95%以上;反应20 min后,MnO₂/Al₂O₃催化剂-微气泡臭氧体系对实际煤化工废水二级出水的TOC去除率可达到55%以上.以叔丁醇作为分子探针,证明了羟基自由基（·OH）氧化作用在臭氧微气泡催化氧化体系中对喹啉的降解起到主导作用.     

Cu/Al2O3低温催化氧化H2S研究

高效低成本的催化剂是低温催化氧化脱除硫化氢（H₂S）的研究重点,采用浸渍法研制了Cu/Al₂O₃催化剂,利用N₂物理吸附、XRD（X射线衍射分析）、XPS（光电子能谱）、FT-IR（傅里叶变换红外光谱）等表征手段了解催化剂的表面结构和物相结构,并开展不同温度、相对湿度、Cu负载量条件下的H₂S动态脱附以考察催化剂脱硫性能.结果表明:①催化剂是一种典型的介孔材料,且CuO和Cu₂O高度分散在催化剂表面.②FT-IR结果表明,催化剂在H₂S催化氧化过程中表面Cu_xO和表面结合水中的羟基均参与反应,且有SO₄2-的生成.③XRD、XPS结果表明,脱硫过程中有S单质和CuS的生成.④适宜的温度（50℃）和相对湿度（50%）会显著增强Cu基催化剂的脱硫性能.⑤负载量为3%的Cu基催化剂具有最佳的脱硫性能,穿透硫容量高达220.92 mg/g.研究显示,利用浸渍法可以合成低温催化氧化H₂S的高硫容Cu基催化剂.      

Al2O3为载体的催化剂净化贫燃汽车尾气研究

在富氧条件下,考察了C₃H₆和C₂H₅OH在Ag/Al₂O₃、In/Al₂O₃、Sn/Al₂O₃、Co/Al₂O₃、Pt/Al₂O₃和Ag/Al₂O₃+Pt/Al₂O₃组合催化剂上选择性还原NO的性能.结果表明,Ag/Al₂O₃具有最高的NO还原活性.在负载型过渡金属氧化物催化剂上,会生成显著量的CO,其HC和CO氧化转化温度也远远高于Pt/Al₂O₃催化剂.串联组合Ag/Al₂O₃+Pt/Al₂O₃催化剂可显著拓宽活性温度范围,促进HC和CO氧化,降低N₂O和CH₃CHO生成量.     

载体结构对Co/MgO-Al2O3催化剂催化C2H6/CO2反应性能的影响

采用共沉淀-浸渍法制备了不同载体结构的Co/Al₂O₃、Co/MgO_（25）-Al₂O_3（75） （Co/M₁A₃-Spinel）、Co/MgO_（75）-Al₂O_3（25） （Co/M₃A₁-Solid）和Co/MgO催化剂,用于CO₂氧化乙烷脱氢（ODEC）和乙烷干重整（DRE）反应.XRD、Raman、H₂-TPR、XPS表征结果表明,载体结构显著影响催化剂上Co物种的落位、结构和还原性能.Co³⁺和Co²⁺在C₂H₆/CO₂反应气氛中可相互转化,促进C₂H₆和CO₂活化;尖晶石结构中的Co物种比固溶体中的Co物种可还原性强,在高温ODEC反应条件下,催化剂表面的Co物种会被还原成Co⁰,协同Co³⁺/Co²⁺导致C—C键和/或CC键断裂,使得反应路径向DRE转变.MgO基固溶体结构中Co物种与载体相互作用更强,在高温ODEC反应中避免了被大量还原为低价态的Co⁰,ODEC反应可稳定进行.     

SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响

用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A1₂O₃催化剂.研究了富氧条件下,SO₂对CH₃OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO₂和H₂O时,NO还原活性温度较低,有显著量N₂O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO₂或同时添加SO₂和H_{2相似文献}   

贫燃条件Ag-Rh/CeO_2-ZrO_2-Al_2O_3协同催化C_3H_6选择性还原NO的原位红外研究

将Ag-Rh浸渍到共沉淀法合成的Ce-Zr-Al上,制备出Ag(0.04)-Rh(x)/Ce0.5Zr0.5O2-75%Al2O3系列催化剂,采用BET比表面积、X射线衍射光谱(XRD)和原位漫反射傅里叶变换红外光谱(DRIFTS)对催化剂进行表征,并探讨催化剂在贫燃条件下选择性还原NO的活性和反应机理.结果表明,Ag-Rh双组分催化剂的活性较单组分Ag、Rh催化剂的高.Rh负载量为0.7%(质量分数)时,NO转化率达最佳(90.3%),且反应的起燃温度低、活性温度范围宽(300～500℃).DRIFTS结果显示,Rh的添加不仅有利于催化剂表面NO的吸附,而且能促进Ag催化生成关键反应中间体—CO—NH—,进而显著提高NO的转化率.     

Catalytic oxidation of benzene over nanostructured porous Co3O4-CeO2 composite catalysts

The three-dimensional structured Co₃O₄-CeO₂ oxides with Co/Ce molar ratio 16:1 gave the highest catalytic activity, which provided more surface hydroxyl groups and more surface oxygenated species.     

Steady-state kinetics and osillation phenomena for complete oxidation of benzene over Pt/Al2O3 catalyst

The steady-state kinetics for complete oxidation of benzene over Pt/Al₂O₃ has been investigated by the external recycling reactor. The kinetics equation was described by the L-H model of adsorption of benzene and oxygen with the inhibition of carbon dioxide. The parameters of the kinetics model were estimated by the method of orthogonal design. The heats of adsorption of benzene, oxygen and carbon dioxide were determined by the method of gas-adsorption chromatography. The details of oscillations of complete oxidation of benzene were investigated.     

Ce-Mn/Al2O3-H2O2催化氧化皮革废水的研究

以浸渍法制备了Ce-Mn/Al_2O_3催化剂,研究该催化剂在H_2O_2非均相类Fenton体系中对皮革废水污染物的催化降解性能.在单因素试验的基础上,以COD去除率为响应值,采用Box-Behnken响应曲面法考察了催化剂投加量、H_2O_2投加量、初始pH、反应时间等4个因素之间的单独作用及交互作用,实验数据用Design-Expert 8.0.6软件进行处理,得到二次响应曲面模型.结果表明,4个独立变量对响应值的影响顺序如下:初始pHH_2O_2投加量催化剂投加量反应时间,数学模型拟合度高(R_(adj)~2=0.9349),利用该模型预测的最大COD去除率为78.86%,最佳反应条件为:催化剂投加量56.63 g·L~(-1),H_2O_2投加量315.15 mg·L~(-1),初始pH3.51,反应时间2 h,经实验验证COD去除率为80.94%,与模型预测值偏差2.08%.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

Decomposition of hexachlorobenzene over Al2O3 supported metal oxide catalysts

Decomposition of hexachlorobenzene (HCB) was investigated over several metal oxides (i.e., MgO, CaO, BaO, La₂O₃, CeO₂, MnO₂, Fe₂O₃, and Co₃O₄) supported on Al₂O₃, which was achieved in closed system at a temperature of 300°C. Catalysts were prepared by incipient wetness impregnation with different metal oxides loading and impregnating solvents. The decomposition efficiency of different catalysts for this reaction depends on the nature of the metal oxide used, and Al₂O₃ supported La₂O₃ was found to be the most active one. Pentachlorobenzene (PeCB), and all tetrachlorobenzene (TeCB), trichlorobenzene (TrCB), and dichlorobenzene (DCB) isomers were detected after the decomposition reaction, indicating that the decomposition was mainly a dechlorination process. The detection of all lower chlorinated benzenes suggested the complexity of decomposition and the presence of more than one dechlorination pathway.     

Treatment of phenol wastewater by microwave-induced ClO2-CuOx/Al2O3 catalytic oxidation process

The catalyst of CuOx/Al2O3 was prepared by the dipping-sedimentation method using γ-Al2O3 as a carrier. CuO and Cu2O were loaded on the surface of γ-Al2O3, characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). In the presence of CuOx/Al2O3, the microwave-induced chlorine dioxide (ClO2) catalytic oxidation process was conducted for the treatment of synthetic wastewater containing 100 mg/L phenol. The relationships between removal percentage and initial ClO2 concentration, catalyst dosage, microwave power, contact time, initial phenol concentration and pH were investigated and the results showed that microwave-induced ClO2-CuOx/Al2O3 process could effectively degrade contaminants in a short reaction time with a low oxidant dosage, extensive pH range. Under a given condition (ClO2 concentration 80 mg/L, microwave power 50 W, contact time 5 min, catalyst dosage 50 g/L, pH 9), phenol removal percentage approached 92.24%, corresponding to 79.13% of CODCr removal. The removal of phenol by microwave-induced ClO2-CuOx/Al2O3 catalytic oxidation process was a complicated non-homogeneous solid/water reaction, which fitted pseudo-first-order by kinetics. Compared with traditional ClO2 oxidation, ClO2 catalytic oxidation and microwave-induced ClO2 oxidation, microwave-induced ClO2 catalytic oxidation system could significantly enhance the degradation efficiency. It provides an effective technology for the removal of phenol wastewater.     

Complete oxidation of methane on Co3O4-SnO2 catalysts

Co₃O₄-SnO₂ hybrid oxides were prepared by the coprecipitation method and were used to oxidate methane (CH₄) in presence of oxygen. The Co₃O₄-SnO₂ with a molar ratio of Co/(Co + Sn) at 0.75 exhibited the highest catalytic activity among all the Co₃O₄-SnO₂ hybrid oxides. Experimental results showed that the catalysts were considerably stable in the CH₄ combustion reaction, and were verified by X-ray photoelectron spectra (XPS). It was found that Co₃O₄ was the active species, and SnO₂ acted as a support or a promoting component in the Co₃O₄-SnO₂ hybrid oxides. The surface area was not a major factor that affected catalytic activity. The hydrogen temperatureprogrammed reduction (H₂-TPR) results demonstrated that the interaction between cobalt and tin oxides accelerated the mobility of oxygen species of Co₃O₄-SnO₂, leading to higher catalytic activity.