Magnetic solid-phase extraction based on Fe3O4/graphene oxide nanoparticles for the determination of malachite green and crystal violet in environmental water samples by HPLC

This work describes a magnetic Fe₃O₄/graphene oxide (GO)-based solid-phase extraction (MSPE) technique for high performance liquid chromatography (HPLC) detection of malachite green (MG) and crystal violet (CV) in environmental water samples. Fe₃O₄/ GO magnetic nanoparticles were synthesised by a chemical co-precipitation method and characterised by scanning electron micrograph, transmission electron microscope, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and surface area analyser. The prepared Fe₃O₄/GO magnetic nanoparticles were used as the adsorbents of MSPE for MG and CV. By coupling with HPLC, a sensitive and cost-effective method for simultaneous determination of MG and CV was developed. The important parameters including the amount of Fe₃O₄/GO, pH of the sample solution, extraction time, salt effect, the type and volume of desorption solvent were investigated in detail. Under optimised conditions, the calibration curves were linear in the concentration range of 0.5–200 μg L^?1, and the limits of detection were 0.091 and 0.12 μg L^?1 for MG and CV, respectively. Finally, the established MSPE-HPLC method was successfully applied to determine MG and CV in environmental water samples with the recoveries ranging from 91.5% to116.7%.     

Fe3O4 nanoparticles as the adsorbent of magnetic solid-phase extraction for clean and preconcentration of maltol and ethyl maltol in food samples followed by HPLC analysis

In this work, a magnetic solid-phase extraction protocol followed with high-performance liquid chromatography analysis was developed for the determination of maltol and ethyl maltol in food samples. The Fe₃O₄ nanoparticles were prepared by one-step hydrothermal method and was used as adsorbent for clean and preconcentrated maltol and ethyl maltol in food samples. The as-prepared Fe₃O₄ nanoparticle was characterized by transmission electron microscope, Fourier transform infrared spectroscopy, X-ray diffraction, and vibrating sample magnetometer. The extraction conditions including the amount of material, extraction time, pH, temperature, and desorption solvents were investigated, respectively. Under the optimized conditions, the detection limits of 0.04 and 0.05?µg?mL^?1 could be achieved for maltol and ethyl maltol. The recoveries between 84.2 and 103.4% with RSDs lower than 2.30% were obtained for the analysis of spiked plum candy sample. The developed method was successfully applied to the analysis of real samples, such as juice, chocolate, and plum candy.     

Development of graphene-carbon nanotube-coated magnetic nanocomposite as an efficient sorbent for HPLC determination of organophosphorus pesticides in environmental water samples

A magnetic solid-phase extraction (MSPE) method coupled to high performance liquid chromatography with UV (HPLC-UV) was proposed for the determination of organophosphorus pesticides (OPPs) at trace levels in environmental water samples. The ternary nanocomposite of graphene-carbon nanotube-Fe₃O₄ (G-CNT-Fe₃O₄) has been synthesised via a simple solvothermal process and the resultant material was characterised by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. Significant factors that affect the extraction efficiency, such as amount of magnetic nanocomposite, extraction time, ionic strength, solution pH and desorption conditions were carefully investigated. The results demonstrated that the proposed method had a wide dynamic linear range (0.005–200 ng mL^?1), good linearity (R² = 0.9955–0.9996) and low detection limits (1.4–11 pg mL^?1). High enrichment factors were achieved ranging from 930 to 1510. The results show that the developed method is suitable for trace level monitoring of OPPs in environmental water samples.     

Synthesis and application of polythiophene-coated Fe3O4 nanoparticles for preconcentration of ultra-trace levels of cadmium in different real samples followed by electrothermal atomic absorption spectrometry

In this research, magnetic Fe₃O₄ nanoparticles were synthesised by co-precipitation method and modified with polythiophene (PT) to produce Fe₃O₄-PT nanoparticles for preconcentration and determination of cadmium (??) ion followed by electrothermal atomic absorption spectrometry. The results of FT-IR spectroscopy, EDX analysis and SEM images show that Fe₃O₄-PT nanoparticles were synthesised successfully. Different parameters such as sample pH, amounts of adsorbent, sample volume, extraction time, type and concentration of eluent and desorption time were completely investigated and optimum conditions were selected.

Under the optimum conditions, the calibration curve was linear in the range of 0.01–0.25 µg L^?1 of cadmium (??). The relative standard deviation was 4.7% (n = 7, 0.10 µg L^?1 Cd²⁺) and limit of detection was 3.30 ng L^?1. The accuracy of the proposed method was verified by the analysis of a certified reference material and spike method. Finally, the proposed method was applied for the determination of ultra-trace levels of cadmium (??) in different water and food samples.     

Fabrication of graphene/Fe3O4@polythiophene nanocomposite and its application in the magnetic solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

Polythiophene (PT) was used as a surface modifier of graphene/Fe₃O₄ (G/Fe₃O₄) composite to increase merit of it, and also overcome some limitations and disadvantages of using G/Fe₃O₄ alone as solid phase extraction (SPE) sorbent. An in-situ chemical polymerization method was employed to prepare G/Fe₃O₄@PT nanocomposites. Application of this newly designed material in the magnetic SPE (MSPE) of polycyclic aromatic hydrocarbons (PAHs), as model analytes, in the environmental water samples was investigated. The characterization of the hybrid material was performed using transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray analysis, Fourier transform-infrared (FT-IR) spectroscopy and vibrating sample magnetometry. Seven important parameters, affecting the extraction efficiency of PAHs, including: amount of adsorbent, adsorption and desorption times, type and volume of the eluent solvent, initial sample volume and salt content of the sample were evaluated. The optimum extraction conditions were obtained as: 4 min for extraction time, 20 mg for sorbent amount, 100 mL for initial sample volume, toluene as desorption solvent, 0.6 mL for desorption solvent volume, 6 min for desorption time and 30% (w/v) for NaCl concentration. Good performance data were obtained at the optimized conditions. Detection limits were in the range of 0.009–0.020 μg L⁻¹ in the real matrix. The calibration curves were linear over the concentration ranges from 0.03 to 80 μg L⁻¹ with correlation coefficients (R²) between 0.995 and 0.998 for all the analytes. Relative standard deviations were ranged from 4.3 to 6.3%. Appropriate recovery values, in the range of 83–107%, were also obtained for the real sample analysis.     

Polythiophene-coated Fe3O4 superparamagnetic nanocomposite: Synthesis and application as a new sorbent for solid-phase extraction

In the present work, a novel type of superparamagnetic nanosorbent, polythiophene-coated Fe₃O₄ nanoparticles (Fe₃O₄@PTh NPs), have been successfully synthesized. The synthesized NPs were characterized by scanning electron microscopy (SEM), Fourier transform-infrared (FT-IR) spectroscopy, and thermal gravimetric analysis (TGA). The synthesized Fe₃O₄@PTh NPs were applied as an efficient sorbent for extraction and preconcentration of several typical plasticizer compounds (di-n-butyl phthalate (DBP), di-(2-ethylhexyl) phthalate (DEHP), and dioctyl adipate (DOA)) from environmental water samples. Separation of Fe₃O₄@PTh NPs from the aqueous solution was simply achieved by applying external magnetic field. Separation and determination of the extracted plasticizers was performed by gas chromatography–flame ionization detection (GC–FID). Several variables affecting the extraction efficiency of the analytes i.e., amount of NPs sorbent, salt concentration, extraction time, and desorption conditions were investigated and optimized. The best working conditions were as follows: amount of sorbent, 100 mg; NaCl concentration, 30% (w/v); sample volume, 45 mL; extraction time, 10 min; and 100 μL of ethyl acetate for desorption of the analytes within 2 min. Under optimized conditions, preconcentration factors for DBP, DEHP, and DOA were obtained as 86, 194, and 213, respectively. The calibration curves were linear (R² > 0.998) in the concentration range of 0.4–100 μg L⁻¹ for both DEHP and DOA and 0.7–100 μg L⁻¹ for DBP. The limits of detection (LODs) were obtained in the range of 0.2–0.4 μg L⁻¹. The intra-day relative standard deviations (RSDs%) based on four replicates were obtained in the range of 4.0–12.3%. The proposed procedure was applied to analysis of water samples including river water, bottled mineral water, and boiling water exposed to polyethylene container (after cooling) and recoveries between 85 and 99% and RSDs lower than 12.8% were obtained.     

Speciation of ultra-trace amounts of inorganic arsenic in water and rice samples by electrothermal atomic absorption spectrometry after solid-phase extraction with modified Fe3O4 nanoparticles

A new magnetic adsorbent, 3-mercaptopropionic acid coated 3-aminopropyl triethoxysilane modified Fe₃O₄ nanoparticle, was synthesised and used for the extraction and preconcentration of arsenic ions in aqueous solutions followed by electrothermal atomic absorption spectrometric determination. The adsorbent was characterised by TEM, SEM, XRD and FT-IR techniques and the method used the unique properties of magnetic nanoparticles, namely, high surface area and superparamagnetism which gave it the advantages of high extraction capacity, fast separation and low adsorbent consumption. Different parameters affecting extraction efficiency of the analyte including pH value, sample volume, adsorbent amount, extraction time and desorption conditions were investigated and optimised. Under the optimum conditions, wide linear range of 30–25,000 ng L^?1 and low detection limit of 10 ng L^?1 were obtained. The interday and intraday precisions (as RSD%) for five replicates determination of 50 and 25,000 ng L^?1 of arsenic ions were in the range of 2.3–3.2%. Furthermore, no significant interference was observed in the presence of coexisting ions and high preconcentration factor of 198 was obtained. The adsorption isotherm followed Langmuir model and its kinetic was second-order. The accuracy of the method was validated by analysing certi?ed reference materials for water and rice with satisfactory recoveries. Finally, the proposed method was successfully applied for the determination of ultra-trace amounts of arsenic in rice and water samples.     

Preparation of a novel Fe3O4/graphene oxide hybrid for adsorptive removal of methylene blue from water

In this work, a novel Fe₃O₄/graphene oxide (GO) hybrid was prepared and its removal ability of cationic methylene blue dye from water was investigated. To improve the dispersability of Fe₃O₄/GO hybrid in water, GO was first modified by polyethylene glycol (PEG) via a click approach before deposition of Fe₃O₄ nanoparticles onto its surface. The successful modification of GO surface and the deposition of Fe₃O₄ nanoparticles were confirmed by transmission electron microscopy directly. The saturation magnetization of the resultant Fe₃O₄/GO hybrid is 7.8 eum/g. The adsorption capacities of Fe₃O₄/GO hybrid for methylene blue at 35 and 60°C were as high as 96.05 and 120.05 mg/g, respectively. Moreover, the Langmuir, Freundlich, and Temkin models are used to investigate the isothermal adsorption behavior of Fe₃O₄/GO hybrid.     

Novel thionin-functionalised core shell magnetic nanoparticles for dispersive solid-phase extraction of Hg(II) in food and water samples

To develop an accurate and precise method for separation and pre-concentration of Hg(II), a novel thionin functionalised core shell structure magnetic material has been prepared and characterised. The extraction ability of the material was evaluated by magnetic solid-phase extraction coupled with inductively coupled plasma mass spectrometry determination of Hg(II) in food and water samples. Combining the advantages of magnetic separation with selective extraction of thionin towards Hg(II), the material exhibits enhanced enrich selectivity and efficiency for Hg(II). The experimental parameters influencing Hg(II) extraction efficiency, including pH of the aqueous solution, the dosage of the adsorbent, extraction time and sample volume, were systematically investigated. Under the optimised conditions, concentration of Hg(II) at 1.0 μg L^?1 can be successfully enriched by the material without the interference of the common co-existing ions. The enrichment factor and adsorption capacity were 250 and 75.2 mg g^?1, and precise of the method was confirmed by analysing the spiked food, water samples and standard water reference samples with the recoveries of 92.5–101.8%.     

Synthesis and Magnetic Properties of Pt3Co/Fe3O4 Nanocomposites

Bimagnetic Pt₃Co/Fe₃O₄ nanocomposite is synthesized in aqueous solution. The nanoparticles are characterized with TEM, FTIR, and magnetic measurements. The as‐synthesized nanocomposite exhibits ferromagnetic properties at room temperature due to the exchange coupling between Pt₃Co and Fe₃O₄. Magnetic properties of Pt₃Co/Fe₃O₄ nanoparticle can be tuned by varying of the molar ratio of iron to platinum. Pt₃Co/Fe₃O₄ nanoparticles exhibit higher saturation magnetization when the molar ratio of iron to platinum is 1.     

Rapid magnetic solid phase extraction with in situ derivatization of methylmercury in seawater by Fe3O4/polyaniline nanoparticle

A new Fe(3)O(4)/polyaniline nanoparticle (PANI) material has been successfully developed as magnetic solid-phase extraction sorbent in dispersion mode for the determination of methylmercury (MeHg) in aqueous samples, via quantification by gas chromatography/mass spectrometry (GC-MS). The resultant core-shell magnetic solid-phase extraction nanoparticle (MSPE-NP) sorbent was characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDS) and Fourier transform-infrared (FTIR) spectroscopy. Fe(3)O(4)/PANI composites showed fibrous structure with diameters between 50 and 100 nm for fibers. The MSPE-NP process involved the dispersion of the Fe(3)O(4)/PANI nanoparticles in water samples with sonication, followed by magnetic aided retrieval of the sorbent and then, solvent (hexane) desorption of extracted MeHg for GC-MS analysis. The extraction, derivatization and adsorption conditions were optimized by selecting the appropriate extraction parameters including the amount of sorbent, extraction time, derivatizing reagent volume and extraction solvent. The calibration graph was linear in the concentration range of 0.5-300 ng mL(-1) (R(2)>0.993) with detection limit of 0.1 ng mL(-1) (n=3), while the repeatability was 4.1% (n=5). Enrichment factor was obtained as 91. Seawater sample was analyzed as real sample and good recoveries (>98%) were obtained at different spiked values.     

Preparation of carbon coated Fe3O4 nanoparticles and their application for solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

The carbon coated Fe₃O₄ nanoparticles (Fe₃O₄/C) were synthesized by a simple hydrothermal reaction and applied as solid-phase extraction (SPE) sorbents to extract trace polycyclic aromatic hydrocarbons (PAHs) from environmental water samples. The Fe₃O₄/C sorbents possess high adsorption capacity and extraction efficiency due to strong adsorption ability of carbon materials and large surface area of nanoparticles, and only 50 mg of sorbents are required to extract PAHs from 1000 mL water samples. The adsorption attains equilibrium rapidly and analytes are eluted with acetonitrile readily. Salinity and solution pH have no obvious effect on the recoveries of PAHs, which avoids fussy adjustment to water sample before extraction. Under optimized conditions, the detection limits of PAHs are in the range of 0.2–0.6 ng L⁻¹. The accuracy of the method was evaluated by the recoveries of spiked samples. Good recoveries (76–110%) with low relative standard deviations from 0.8% to 9.7% are achieved. This new SPE method provides several advantages, such as high extraction efficiency, high breakthrough volumes, convenient extraction procedure, and short analysis times. To our knowledge, this is the first time that Fe₃O₄/C nanoparticles are used for the pretreatment of environmental water samples.     

Mixed hemimicelles solid-phase extraction of chlorophenols in environmental water samples with 1-hexadecyl-3-methylimidazolium bromide-coated Fe3O4 magnetic nanoparticles with high-performance liquid chromatographic analysis

In this paper, 1-hexadecyl-3-methylimidazolium bromide (C₁₆mimBr)-coated Fe₃O₄ magnetic nanoparticles (NPs) as an adsorbent of mixed hemimicelles solid-phase extraction was investigated for the preconcentration of two chlorophenols (CPs) in environmental water samples prior to HPLC with UV detection at 285 nm. The high surface area and excellent adsorption capacity of the Fe₃O₄ NPs after modification with C₁₆mimBr were utilized adequately in the SPE process. By the rapid isolation of Fe₃O₄ NPs through placing a strong magnet on the bottom of beaker, the time-consuming preconcentration process of loading large volume sample in conventional SPE method with a column can be avoided. A comprehensive study of the adsorption conditions such as the zeta-potential of Fe₃O₄ NPs, added amounts of C₁₆mimBr, pH value, standing time and maximal extraction volume were also presented. Under optimized conditions, two analytes of 2,4-dichlorophenol (2,4-DCP) and 2,4,6-trichlorophenol (2,4,6-TCP) were quantitatively determined. The method was then used to determine the two CPs in real environmental water samples. The accuracy of method was evaluated by recovery measurements on spiked samples. Good recovery results (74–90%) were achieved. It is important to note that satisfactory preconcentration factors and extraction recoveries for the two CPs were obtained with only a small amount of Fe₃O₄ NPs (40 mg) and C₁₆mimBr (24 mg).     

Facile synthesis of multifunctional attapulgite/Fe3O4/polyaniline nanocomposites for magnetic dispersive solid phase extraction of benzoylurea insecticides in environmental water samples

In this study, the superparamagnetic attapulgite/Fe₃O₄/polyaniline (ATP/Fe₃O₄/PANI) nanocomposites were successfully synthesized by a one-pot method. Fe (III) was applied as both the oxidant for the oxidative polymerization of aniline and the single iron source of Fe₃O₄ formed by the redox reaction between aniline and Fe (III). The ATP/Fe₃O₄/PANI was used as sorbent for magnetic dispersive solid phase extraction (MDSPE) of benzoylurea insecticides (BUs) in environmental water samples. The as-prepared nanocomposite sorbents were characterized by Fourier transform infrared spectra (FT-IR), X Ray diffraction (XRD), scanning electron microscopy(SEM), transmission electron microscopy (TEM), and vibrating sample magnetometry. Various experimental parameters affecting the ATP/Fe₃O₄/PANI-based MDSPE procedure, including the composition of the nanocomposite sorbents, amount of ATP/Fe₃O₄/PANI nanocomposites, vortex time, pH, and desorption conditions were investigated. Under the optimal conditions, a good linearity was observed for all target analytes, with correlation coefficients (r²) ranging from 0.9985 to 0.9997; the limits of detection (LOD) were in the range of 0.02–0.43 μg L⁻¹, and the recoveries of analytes using the proposed method ranged between 77.37% and 103.69%. The sorbents exhibited an excellent reproducibility in the range of 1.52–5.27% in extracting the five target analytes. In addition, the intra-day and inter-day precision values were found to be in the range of 0.78–6.86% and 1.66–8.41%, respectively. Finally, the proposed ATP/Fe₃O₄/PANI-based MDSPE method was successfully applied to analyze river water samples by rapid preconcentration of BUs.     

Synthesis of orientedly bioconjugated core/shell Fe3O4@Au magnetic nanoparticles for cell separation

Orientedly bioconjugated core/shell Fe₃O₄@Au magnetic nanoparticles were synthesized for cell separation. The Fe₃O₄@Au magnetic nanoparticles were synthesized by reducing HAuCl₄ on the surfaces of Fe₃O₄ nanoparticles, which were further characterized in detail by TEM, XRD and UV-vis spectra. Anti-CD3 monoclonal antibody was orientedly bioconjugated to the surface of Fe₃O₄@Au nanoparticles through affinity binding between the Fc portion of the antibody and protein A that covalently immobilized on the nanoparticles. The oriented immobilization method was performed to compare its efficiency for cell separation with the non-oriented one, in which the antibody was directly immobilized onto the carboxylated nanoparticle surface. Results showed that the orientedly bioconjugated Fe₃O₄@Au MNPs successfully pulled down CD3⁺ T cells from the whole splenocytes with high efficiency of up to 98.4%, showing a more effective cell-capture nanostructure than that obtained by non-oriented strategy. This developed strategy for the synthesis and oriented bioconjugation of Fe₃O₄@Au MNPs provides an efficient tool for cell separation, and may be further applied to various fields of bioanalytical chemistry for diagnosis, affinity extraction and biosensor.     

Preparation of polypyrrole-coated magnetic particles for micro solid-phase extraction of phthalates in water by gas chromatography-mass spectrometry analysis

In this work, polypyrrole (PPy)-coated Fe(3)O(4) magnetic microsphere were successfully synthesized, and applied as a magnetic sorbent to extract and concentrate phthalates from water samples. The PPy-coated Fe(3)O(4) magnetic microspheres had the advantages of large surface area, convenient and fast separation ability. The PPy coating of magnetic microspheres contributed to preconcentration of phthalates from water sample, due to the π-π bonding between PPy coating and the analytes. Also, the coating could prevent aggregation of the microspheres, and improve their dispersibility. In this study, seven kinds of phthalates were selected as model analytes, including dimethyl phthalate (DMP), diethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) and di-n-octyl phthalate (DNOP), and gas chromatography-mass spectrometry (GC-MS) was introduced to detect the phthalates after sample pretreatment. Important parameters of the extraction procedure were investigated, and optimized including eluting solvent, the amount of Fe(3)O(4)@PPy particles, and extraction time. After optimization, the procedure took only 15 min to extract and concentrate analytes with high efficiency. Validation experiments showed that the optimized method had good linearity (0.985-0.998), precision (3.4-11.7%), high recovery (91.1-113.4%), and the limits of detection were from 0.006 to 0.068 μg/L. The results indicated that the novel method had advantages of convenience, good sensitivity, high efficiency, and it could also be applied successfully to analyze phthalates in real water sample.     

Quantification of 1-hydroxypyrene in undiluted human urine samples using magnetic solid-phase extraction coupled with internal extractive electrospray ionization mass spectrometry

Polycyclic aromatic hydrocarbons (PAHs) are a group of ubiquitous environmental contaminants raising worldwide concerns due to their carcinogenic effects. In this study, 1-hydroxypyrene (1-OHP, the most widely used biomarker of internal dose of PAHs exposure) in undiluted human urine samples (10 mL) was selectively enriched by polypyrrole-coated Fe₃O₄ magnetite nanocomposites (termed as Fe₃O₄@Ppy, 1 mg) and then directly eluted by the electrospraying solvent (acetone/benzene/acetic acid (v/v/v, 90/10/1); 100 uL) biased with −3.5 kV to produce the deprotonated 1-OHP anions for mass spectrometric analysis. The method established here significantly improved the current performance for detection of urinary 1-OHP, providing the speed for a single sample analysis within 4 min, the limits of detection (LOD) of 0.0001 μg L⁻¹, the linear response range of 0.001–5.000 μg L⁻¹ (R² = 0.9994), recovery rates of 90.6–96.1%, and relative standard deviation (RSD, n = 6) values between 2.9% and 8.0%. Human samples including raw human urine collected from 10 healthy volunteers (5 smokers and 5 nonsmokers) and 7 lung cancer patients have been successfully analyzed, showing that magnetic solid-phase extraction (MSPE) coupled with internal extractive electrospray ionization mass spectrometry (iEESI-MS) is an alternative strategy for high throughput quantitative detection of urinary 1-OHP for health risk assessment of PAHs exposure.     

Magnetic solid-phase extraction of Zineb by C18-functionalised paramagnetic nanoparticles and determination by first-derivative spectrophotometry

Fe₃O₄-SiO₂-C₁₈ paramagnetic nanoparticles have been synthesised and used as magnetic solid-phase extraction (MSPE) sorbent for the extraction of Zineb from agricultural aqueous samples under ultrasonic condition and quantified through a first-derivative spectrophotometric method. The produced magnetic nanoparticles were characterised by using scanning electron microscopy, X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy and zeta potential reader. The Fe₃O₄-SiO₂-C₁₈ paramagnetic nanoparticles had spherical structures with diameters in the range of 198–201 nm. Further, MSPE was performed by dispersion of Fe₃O₄-SiO₂-C₁₈ paramagnetic nanoparticles in a buffered aqueous solution accompanied by sonication. Next, the sorbents were accumulated by applying an external magnetic field and were washed with 4-(2-pyridylazo) resorcinol-dimethyl sulfoxide solution, for the purpose of desorbing the analyte. The extraction conditions (sample pH, washing and elution solutions, amount of sorbents, time of extraction, sample volume and effect of diverse ions), as well as Zineb-PAR first-order derivative spectra, were also evaluated. The calibration curve of the method was linear in the concentration range of 0.055–24.3 mg L^?1 with a correlation coefficient of 0.991. The limit of detection and limit of quantification values were 0.022 and 0.055 mg L^?1, respectively. The precision of the method for 0.27 mg L^?1 solution of the analyte was found to be less than 3.2%. The recoveries of three different concentrations (0.27, 1.37 and 13.7 mg L^?1) obtained 98.3%, 98.5% and 96.0%, respectively. The proposed Fe₃O₄-SiO₂-C₁₈ paramagnetic nanoparticles were found to have the capability of reusing for 7.0 times.     

磁性Fe3O4亚微米球固相萃取-HPLC检测水中植物生长调节剂残留

建立了水中2,4-二氯苯氧乙酸(2,4-D)、萘乙酸(NAA)和6-芐基腺嘌呤(6-BA)3种植物生长调节剂残留分析的高效液相色谱方法.采用溶剂热还原法,以乙二醇和FeCl3·6H2O作原料,合成出形貌均一、分散性好、稳定性佳的磁性Fe3O4亚微米球,作为固相萃取材料,以静电吸附作用可以富集水中残留的2,4-D、NAA、6-BA 3种植物生长调节剂.水样经调节pH值和固相萃取净化后,高效液相色谱法测定.3种植物生长调节剂在0.1 ～10 mg/L范围内响应和浓度的线性关系良好,相关系数均大于0.999;2,4-D、NAA、6-BA的检测限分别为0.06、0.02、0.04 mg/L.在测定的自来水、河水和湖水3种水样中,添加回收率范围为73.20％ ～87.21％,相对标准偏差为1.11％ ～7.52％(n=3),为水中的2,4-D、NAA和6-BA残留监控提供了简单、快速、准确的测定方法.