共查询到20条相似文献,搜索用时 140 毫秒
1.
文章基于ARM与CPLD技术设计了一种虚拟数字存储示波器.以S3C2410和EPM7128为控制器,采用高速A/D转换芯片AD9283设计数据采集卡.采用USB总线实现数据采集卡和PC机通信,基于Lab-VIEW开发虚拟示波器的控制面板及应用程序.该虚拟示波器具有数据采集,波形显示、频谱分析、数据存储与回放等功能. 相似文献
2.
根据高等工科院校实验教学中实验设备紧张的现实,介绍虚拟平台下虚拟仪器的开发,并用LabVIEW软件结合PCI6024E数据采集卡设计实现了一款虚拟数字存储示波器,该示波器具有波形显示、读写、存储、打印和测量参数数字显示功能.实际使用结果表明,示波器精度和稳定性都能满足使用要求.在此基础上增加软件设计,还可实现频谱分析仪,万用表,频率计等功能,实现仪器的一机多用. 相似文献
3.
4.
文章基于ARM与CPLD技术设计了一种虚拟数字存储示波器。以S3C2410和EPM7128为控制器,采用高速A/D转换芯片AD9283设计数据采集卡。采用USB总线实现数据采集卡和PC机通信,基于Lab-VIEW开发虚拟示波器的控制面板及应用程序。该虚拟示波器具有数据采集、波形显示、频谱分析、数据存储与回放等功能。 相似文献
5.
5脉冲测量 可用示波器测量和表征脉冲列(和方波),测量方面涉及示波器基本接驳至有意义的波形,取得波形的电压对时间的显示,并且从显示中抽取有关的参数,示波器必须持有足够的上升时间和频宽,令被测的脉冲不致腐化. 相似文献
6.
本文叙述了高重复率Nd~(3 ):YAG调Q脉冲激光器一些主要工作参数(储能电容脉冲电压及充放电波形、氙灯工作电压及波形,氙灯电流脉冲及光脉冲波形,激光脉冲波形、能量、峰值功率,光束发散及激光脉冲的脉间起伏和平均起伏……等)的光电子测量技术。给出了测量方法的选择原则,所使用的仪器和获得各种波形照片。 相似文献
7.
用PC直接获取数字示波器波形和联机波形参数测量 总被引:1,自引:0,他引:1
数字存储示波器,顾名思义除了能实现一般的显示波形功能之外,更重要的是能将屏幕上显示的波形保存下来,以便作再次观察和其它用途,这是数字存储示波器和普通示波器的根本区别。据了解,一般的数字存储示波器用户,都会使用它进行测量和观察波形,对如何存储波形的方法并没有去研究或不太了解。本文提供了利用电脑与安捷伦数字存储示波器实现联机,并利用电脑直接将示波器的波形存储下来,和对存储下来的波形进行参数测量分析等方法,对数字存储示波器用户有一定的参考价值。 相似文献
8.
数字存储示波器的研究与设计 总被引:1,自引:0,他引:1
与传统的模拟示波器相比,数字存储示波器可显示非周期波形并可存储波形,同时具有携带方便等优点,文中详细介绍了数字存储示波器的原理及特点,给出了一种以单片机和可编程逻辑器件为控制核心的设计方案,同时给出了其硬件和软件设计的结构及思路. 相似文献
9.
10.
由于器件和功能的增多导致电路的测试和调试越来越困难,要全真地捕获非周期的噪声、串扰和瞬时等信号几乎不可能。通过分析数字示波器的原理,探知示波器的静默和捕获过程,分析总结了三家著名示波器生产厂家对波形捕获所应用的各项新技术。通过随机概论理论对波形捕获率的分析,得到了捕获率的量化计算公式和影响因素。提出了触发输出法和双脉冲计数法二种测试示波器波形捕获率的方法,并对市场中常见示波器的捕获率进行了实测验证。 相似文献
11.
12.
新型Q开关晶体Cr4+:YAG的生长和被动调Q研究 总被引:2,自引:0,他引:2
本文工作采用二价Ca离子作为电荷补偿离子由提拉法生长出了具有高光学质量的调Q开关晶体Cr^4 :YAG。所生长的晶体在空气中退火(1450℃)50小时后,晶体的颜色明显加深,吸收光谱测量表明晶体中的Cr^4 离子浓度得到显著提高。在闪光灯泵浦的Nd:YAG激光器上对不同透过率、退火后的Cr^4 :YAG晶体进行了被动调Q实验。结果表明所生长出的Cr^4 :YAG晶体对Nd:YAG激光器具有很好的调Q作用。 相似文献
13.
为了研究脉冲输出波长为1319nm的Nd:YAG激光器,通过分析Nd:YAG激光介质的辐射跃迁能级,采用镀制高选择性介质膜的方法抑制1064nm等其它波长的起振,最终实现1319nm激光单脉冲输出。实验中采用闪光灯抽运、水冷Nd:YAG激光器,KD*P调Q,平平腔结构,获得1319nm激光静态输出能量340.9mJ,动态输出76.8mJ,重频1Hz,脉宽17ns,束散角2.7mrad。结果表明,通过镀制高选择性介质膜的方法可以实现1319nm激光调Q脉冲输出。 相似文献
14.
A comparison of rare-gas flashlamps for pumping YAG: Nd3+and neodymium-doped glass, which shows krypton lamps to be superior to xenon under certain circumstances, is presented. The emission spectra of argon have the best match to the neodymium absorption spectra, but argon lamps suffer from low radiative efficiency except at very high pressures. A detailed analysis of theoretical laser thresholds, which takes into account pump-pulse duration, cavity transfer coefficient, laser rod diameter, lamp emission spectra, and other pertinent parameters, is compared to experimental threshold data with good agreement. Krypton at 500-mm pressure gives a 19-percent improvement in the YAG : Nd3+threshold over a comparable xenon lamp at low current densities. Xenon is generally superior to krypton for pumping glass rods because of the greater absorption at 5900 Å where xenon is intrinsically a better radiator. However, proper lamp optimization shows a definite improvement in threshold with krypton at low drive levels. Xenon is anticipated to be superior to krypton at high current densities since line radiation will no longer contribute significantly to the pumping process. Proper optimization of lamp and cavity parameters should permit a slope efficiency of ∼6 percent for neodymium lasers to be realized. 相似文献
15.
Arya R. Thomas J.M. Bhujle A.G. Bhawalkar D.D. 《Quantum Electronics, IEEE Journal of》2000,36(7):872-878
This paper reports the results of investigations carried out on the influence of simmer current on flashlamp impedance and performance of a flashlamp-pumped Nd:YAG laser operating in the quasi-CW mode. A pulse power source with an adjustable output pulsewidth (1-20 ms) and an adjustable simmer current source (30 mA to 6 A) developed specifically for the study were used. It is found that the simmering of the lamp reduces the impedance factor of the lamp, increases the correct arc diameter, and reduces the peak current density of the flashlamp discharge. It improves the efficiency of the flashlamp pump source and, hence, the efficiency of the Nd:YAG laser also. An appropriate choice of the simmer current, using the results obtained, can lead to higher efficiency of the laser and increased life of the lamp 相似文献
16.
17.
KTP倍频Nd:YAG激光和Ho:YAG激光心肌打孔组织学变化的对比研究 总被引:4,自引:0,他引:4
目的 :比较国产 KTP倍频 Nd:YAG激光和 Ho:YAG激光对离体猪心激光打孔的组织学效应 ,探讨国产 KTP倍频 Nd:YAG激光用于激光心肌血运重建术的可能性。方法 :分别用 KTP倍频 Nd:YAG激光和 Ho:YAG激光以多种级别的工作参数对离体猪心左心室心内膜面进行照射 ,行病理组织学检查 ,测量激光孔道直径、深度及坏死层厚度。结果 :KTP倍频 Nd:YAG激光和 Ho:YAG激光均能有效形成激光孔道 ,随能量增加 ,孔道深度增加。KTP倍频 Nd:YAG激光具有孔道直、热损伤小的优点。结论 :KTP倍频 Nd:YAG激光是激光心肌血运重建术可供选择的激光源。 相似文献
18.
19.
Kam-chuen Yung Chung-pang Lee Ching-hong Wong Siu-lim Tam Siu-kwong Pang Tai-man Yue 《Journal of Electronic Materials》2013,42(12):3494-3501
Optical waveguide cross-sectional shapes that deviate from rectangles or squares may cause significant loss of signal. In this study, a photolithography approach was adopted to fabricate waveguides on printed circuit boards, using photo-imageable polysiloxane as a waveguide material. The effects of I-line ultraviolet (UV) lamp exposure, 355-nm Nd:YAG laser direct imaging, and 248-nm excimer laser direct imaging on the cross-sectional shape of waveguides were investigated. For I-line UV lamp exposure, increasing the exposure time could cause changes in the tilt angle of the waveguides from negative (inverted trapezoid) to positive (trapezoid). To obtain rectangular waveguides, the optimum I-line UV lamp exposure time was found to be around 150 s. From the results for 355-nm Nd:YAG laser direct imaging, the width and tilt angle of the waveguides varied with the energy density of the laser beam irradiating the core materials, being controlled by the repetition rate and focus. Lowering the laser energy density could produce waveguides with small widths and tilt angles. Excimer laser direct imaging at 248 nm was found to be unsuitable for waveguide patterning since the core materials could not be cured at this wavelength. 相似文献
20.
高效风冷小型化电光调Q—Nd:Ce:YAG激光器 总被引:2,自引:0,他引:2
本文通过对闪光灯泵浦铌酸锂晶体电光Q开关Nd:YAG激光器的理论分析,总结了影响其输出效率的因素,提出了改进激光器设计,提高效率和可靠性的方法,在此基础上,介绍一种高效,小型化凤冷,电光调Q-Nd:YAG激光器的设计方法和试验结果:其动态输出效率达1.4-2.0%,且体积小,可靠性高,适应现代工程的需要。 相似文献