厌氧生物滤池+生物接触氧化组合工艺处理地表微污染水技术研究

通对通惠河通州段地表微污染水进行水质改善处理技术研究,确定采用厌氧生物滤池+生物接触氧化的组合工艺进行处理,通过试验确定工艺的最佳运行参数为厌氧生物滤池HRT=15 h,生物接触氧化池气水比10,水力停留时间为4 h,回流比为100%。出水中氨氮浓度为0.34 mg/L,总氮浓度为3.2 mg/L,总磷浓度为0.38 mg/L,CODCr浓度为34 mg/L,出水各指标完全满足《地表水环境质量标准(GB3838-2002)》中Ⅴ类水体质量标准,其中总氮浓度远低于课题研究目标的15 mg/L。     

多级串联接触氧化法处理漂染废水

漂染废水处理的主体工艺流程可以采用气浮法预处理→水解酸化 接触氧化法生化处理→氧化脱色后处理工艺 ,出水水质可以达到《纺织染整工业水污染物排放标准》(GB4 2 87- 92 )一级标准。工程实践与工艺分析表明 ,多级串联接触氧化法中 ,各级微生物数量及形态保持相对独立 ,表现出类似于AB工艺的特征 ,结合预处理及后处理措施处理漂染废水具有效果好、运行稳定、投资少及占地面积省等优点。在具体工艺设计上 ,依水流方向 ,各级接触氧化池负荷由高至低分布 ,宜采取较低的有机负荷及较长的反应时间     

Determination of dairy wastewater treatability by bio-trickling filter packed with lava rocks - case study PEGAH dairy factory

This paper investigates the effectiveness of a biological trickling filter for the treatment of wastewaters produced by a company manufacturing dairy products. First a bio-trickling column with a height of 150 cm was packed with lava rocks from north mountain of Tehran. It operates with the recirculation of liquid through the packing. In order to startup the pilot scale, steady state condition was gained by pumping activated sludge and dairy wastewater for 23 days. Afterwards, dairy wastewater was added to liquid tank for treatment. Hydraulic retention time (HRT) of treatment decreases from 5 days to 1 day then at HRT of 12, 8, 7, 6 and 4 h. Results show that the average chemical oxygen demand (COD) decreased from 2,750 to 98 mg/L at HRT of 7 h and efficiency of TKN removal was more than 70%. The microorganisms developed in the bio-trickling filter were able to efficiently remove COD levels up to 2,750 mg/L, under aerobic conditions at pH values between 6.8 and 7.2 under low temperature condition between 10 and 13 °C.     

ABR反应器对垃圾渗滤液的处理试验研究

ABR工艺在处理垃圾渗滤液中具有其他厌氧生物反应器所达不到的优点。尤其是对B/C低、氨氮浓度高、COD浓度高的废水处理,通过调节回流比、HRT、碱度等参数后,可以取得很好的处理效果。在本次实验中,HRT控制在18h后明显提高的垃圾渗滤液的可生化性及C/N,使ABR出水CODcr去除率达到75%,C/N为6.72,对后续好氧反应起到了重要作用。在调控一定回流比后,为提供厌氧氨氧化所需的电子受体NO-3和NO-2实现脱氮。反应器在经过120d的培养驯化,氨氮进水为460mg/L,ABR对氨氮的去除率稳定在80%。不同格室的厌氧颗粒污泥都得到很好的驯化并在其合适的环境中发挥各自的功能。     

MBR与接触氧化工艺用于中水处理的比较

某高校中水处理工程采用MBR代替接触氧化工艺进行改造,在实际运行情况的基础上,对MBR和接触氧化工艺在工艺流程、处理效果、投资成本和运行维护管理等方面进行比较,结果表明,MBR在各方面均体现出较强的优势,为MBR的实际应用和发展提供参考。     

某大型综合医院污水处理系统问题与对策

以某大型综合医院污水处理系统为研究对象,分析了其水量变化规律和两种处理工艺的运行效果,研究了其化粪池、曝气生物滤池、生物接触氧化罐等设施存在的主要问题,并提出了相应的技术对策。     

Anoxic sulfide oxidation in wastewater of sewer networks.

Investigations on anoxic sulfide oxidation in wastewater under sewer conditions are presented. Batch tests were designed and conducted to study both chemical and biological sulfide oxidation by nitrate in the water phase. Oxidation at pH 7.0 and 8.5 was performed in parallel and wastewater with anaerobic storage period of 0, 3, 4, 6 days was used. Initial sulfide concentrations at a level of 0-4.1 g S m(-3) were applied by either addition or sulfate reduction. Results showed that wastewater in sewers was capable of biological, but not chemical, sulfide oxidation under anoxic conditions. Elemental sulfur was the end-product during the experiment. Nitrite accumulates in wastewater as an intermediate. The anoxic oxidation rates for fresh wastewater was 0.48 g S m(-3) h(-1) at pH 7.0 and 0.62 g S m(-3) h(-1) at pH 8.5, which accounted for less than 30% of the potential aerobic oxidation rates. A long-term anaerobic adaptation of the wastewater was found to inhibit the oxidation process.     

Performance of a modified RBC system in simulated municipal wastewater treatment

A new method based on rotating biological contactor (RBC) was employed for solving the problems of long hydraulic retention times (HRT) low specific surface area and organic loading rates (OLR) in conventional RBCs. The system showed its particular adsorption ability of microorganisms in the biofilm-attaching period. Microbes on the first cage were observed in comparison with the second one. Packing biodisc also had a good shock load tolerance. It was observed that the system performance improved at higher HRTs, while at the increased level of input OLR, the removal performance worsened slightly. The positive role of rotational speed in the treatment of municipal wastewater was more pronounced in the range of 10-12 rpm. Chemical oxygen demand (COD) removal rate achieved 94% under the optimal operating conditions, which were HRT of 1.5 h, rotational speed of 9.9 rpm. The modified RBC system is highly beneficial to engineering application for better system performance and lower energy consumption.     

Treatment of low and medium strength sewage in a lab-scale gradual concentric chambers (GCC) reactor.

One of the major challenges of anaerobic technology is its applicability for low strength wastewaters, such as sewage. The lab-scale design and performance of a novel Gradual Concentric Chambers (GCC) reactor treating low (165+/-24 mg COD/L) and medium strength (550 mg COD/L) domestic wastewaters were studied. Experimental data were collected to evaluate the influence of chemical oxygen demand (COD) concentrations in the influent and the hydraulic retention time (HRT) on the performance of the GCC reactor. Two reactors (R1 and R2), integrating anaerobic and aerobic processes, were studied at ambient (26 degrees C) and mesophilic (35 degrees C) temperature, respectively. The highest COD removal efficiency (94%) was obtained when treating medium strength wastewater at an organic loading rate (OLR) of 1.9 g COD/L.d (HRT = 4 h). The COD levels in the final effluent were around 36 mg/L. For the low strength domestic wastewater, a highest removal efficiency of 85% was observed, producing a final effluent with 22 mg COD/L. Changes in the nutrient concentration levels were followed for both reactors.     

草甘膦废水预处理研究与工程应用

某草甘膦废水处理站已无法达到处理要求,需要进行改造.为了减轻后续的生化处理负荷,强化对草甘膦废水的除磷预处理,选用电絮凝氧化、Fenton氧化和电磁-Fenton氧化3种工艺作为草甘膦废水预处理工艺,进行了比选试验.试验结果表明,Fenton氧化为本工程的草甘膦废水最佳预处理工艺,可达到预期效果.     

Innovations in wastewater treatment: the moving bed biofilm process.

This paper describes the moving bed biofilm reactor (MBBR) and presents applications of wastewater treatment processes in which this reactor is used. The MBBR processes have been extensively used for BOD/COD-removal, as well as for nitrification and denitrification in municipal and industrial wastewater treatment. This paper focuses on the municipal applications. The most frequent process combinations are presented and discussed. Basic design data obtained through research, as well as data from practical operation of various plants, are presented. It is demonstrated that the MBBR may be used in an extremely compact high-rate process (<1 h total HRT) for secondary treatment. Most European plants require P-removal and performance data from plants combining MBBR and chemical precipitation is presented. Likewise, data from plants in Italy and Switzerland that are implementing nitrification in addition to secondary treatment are presented. The results from three Norwegian plants that are using the so-called combined denitrification MBBR process are discussed. Nitrification rates as high as 1.2 g NH4-N/m2 d at complete nitrification were demonstrated in practical operation at low temperatures (11 degrees C), while denitrification rates were as high as 3.5g NO3-Nequiv./m2.d. Depending on the extent of pretreatment, the total HRT of the MBBR for N-removal will be in the range of 3 to 5 h.     

Combining biocatalyzed electrolysis with anaerobic digestion.

Biocatalyzed electrolysis is a microbial fuel cell based technology for the generation of hydrogen gas and other reduced products out of electron donors. Examples of electron donors are acetate and wastewater. An external power supply can support the process and therefore circumvent thermodynamical constraints that normally render the generation of compounds such as hydrogen unlikely. We have investigated the possibility of biocatalyzed electrolysis for the generation of methane. The cathodically produced hydrogen could be converted into methane at a ratio of 0.41 mole methane mole(-1) acetate, at temperatures of 22+/-2 degrees C. The anodic oxidation of acetate was not hampered by ammonium concentrations up to 5 g N L(-1). An overview is given of potential applications for biocatalyzed electrolysis.     

酸析—微电解—Fenton氧化预处理亚麻脱胶废水的研究

高浓度亚麻脱胶废水CODCr、色度都很高,不宜直接进行生物处理.试验采用酸析-微电解-Fenton氧化的预处理工艺,并对反应的影响因素进行了研究,试验结果表明,在pH=3,微电解90 min,H2O2投量1 500 mg/L,Fenton氧化120 min的条件下,CODCr去除率可以达到71.4%,色度去除率超过90%.同时该方法提高了废水的可生化性,有利于后续的生化处理.     

Effective degradation of para-chloronitrobenzene through a sequential treatment using zero-valent iron reduction and Fenton oxidation

In this study, zero-valent iron (ZVI) was used to pretreat para-chloronitrobenzene (p-CNB), and the major product was para-chloroaniline (p-CAN). By adding H(2)O(2) directly, further p-CAN degradation can be attributed to Fenton oxidation because ferrous ions (Fe(2+)) released during the ZVI corrosion could be used as an activator for H(2)O(2) decomposition. In the reduction process, the reduction efficiency of p-CNB as well as Fe(2+) concentration increased with increasing iron dosage and decreasing solution pH. Under the optimal conditions, 25 mg L(-1) of p-CNB could be transformed in 3 h when initial solution pH was 3.0 and ZVI dosage was 2.0 g L(-1). A sufficient amount of Fe(2+) (50.4 mg L(-1)) was obtained after the above reaction to activate H(2)O(2). In the Fenton process, the oxidization of p-CAN was also more effective in acidic conditions and it increased with increasing H(2)O(2) concentration. The control experiments showed that the sequential treatment was more effective than Fenton oxidation alone in treating p-CNB wastewater since the removal rate of total organic carbon (TOC) was improved by about 34%. It suggested that the amino function group is more susceptible to oxidative radical attack than the nitro function group. Therefore, sequential treatment using zero-valent iron reduction followed by Fenton oxidation is a promising method for p-CNB degradation.     

Application of a combined process of moving-bed biofilm reactor (MBBR) and chemical coagulation for dyeing wastewater treatment.

A combined process consisted of a Moving-Bed Biofilm Reactor (MBBR) and chemical coagulation was investigated for textile wastewater treatment. The pilot scale MBBR system is composed of three MBBRs (anaerobic, aerobic-1 and aerobic-2 in series), each reactor was filled with 20% (v/v) of polyurethane-activated carbon (PU-AC) carrier for biological treatment followed by chemical coagulation with FeCl2. ln the MBBR process, 85% of COD and 70% of color (influent COD = 807.5 mg/L and color = 3,400 PtCo unit) were removed using relatively low MLSS concentration and short hydraulic retention time (HRT = 44 hr). The biologically treated dyeing wastewater was subjected to chemical coagulation. After coagulation with FeCl2, 95% of COD and 97% of color were removed overall. The combined process of MBBR and chemical coagulation has promising potential for dyeing wastewater treatment.     

太原精神病院污水处理系统改建为中水处理系统的工程设计

太原精神病医院将现有生活污水处理系统改建为中水回用系统,平均日处理水量100 m3.工程设计充分考虑了对原有设施的利用,生物处理单元采用生物接触氧化法.为减少污水提升次数,调节池设在生物处理单元之后.通过延长水力停留时间缓解水量、水质波动对沉淀、生物处理单元的不利影响,投入运行后效果良好.     

Nutrients removal in hybrid fluidised bed bioreactors operated with aeration cycles.

Abstract Two hybrid fluidised bed reactors filled with sepiolite and granular activated carbon (GAC) were operated with short cycled aeration for removing organic matter, total nitrogen and phosphorous, respectively. Both reactors were continuously operated with synthetic and/or industrial wastewater containing 350-500 mg COD/L, 110-130 mg NKT/L, 90-100 mg NH3-N/L and 12-15 mg P/L for 8 months. The reactor filled with sepiolite, treating only synthetic wastewater, removed COD, ammonia, total nitrogen and phosphorous up to 88, 91, 55 and 80% with a hydraulic retention time (HRT) of 10 h, respectively. These efficiencies correspond to removal rates of 0.95 kgCODm(-3)d(-1) and 0.16 kg total N m(-3)d(-1).The reactor filled with GAC was operated for 4 months with synthetic wastewater and 4 months with industrial wastewater, removing 98% of COD, 96% of ammonia, and 66% of total nitrogen, with an HRT of 13.6 h. No significant phosphorous removing activity was observed in this reactor. Microbial communities growing with both reactors were followed using polymerase chain reaction (PCR) and denaturing gradient gel electrophoresis (DGGE) techniques. The microbial fingerprints, i.e. DGGE profiles, indicated that biological communities in both reactors were stable along the operational period even when the operating conditions were changed.     

济南市分散式污水处理站典型工艺及运行管理分析

以济南市政府投资建设的8座分散式污水处理站为例,介绍了两级生物滤池、ETS生态处理、KIC生物接触氧化3种典型工艺,分析了污水处理站的运行成本,提出了运行管理中的问题和建议。     

Aerobic biological treatment of thermophilically digested sludge

Aerobic biological treatment of digested sludge was studied in a continuously operated laboratory set-up. An aerated reactor was filled with thermophilically digested sludge from the Moscow wastewater treatment plant and inoculated with special activated sludge. It was then operated at the chemostat mode at different flow rates. Processes of nitrification and denitrification, as well as dephosphatation, occurred simultaneously during biological aerobic treatment of thermophilically digested sludge. Under optimal conditions, organic matter degradation was 9.6%, the concentrations of ammonium nitrogen and phosphate decreased by 89 and 83%, respectively, while COD decreased by 12%. Dewaterability of digested sludge improved significantly. The processes were found to depend on hydraulic retention time, oxygen regime, and temperature. The optimal conditions were as follows: hydraulic retention time 3-4 days, temperature 30-35 degrees C, dissolved oxygen levels 0.2-0.5 mg/L at continuous aeration or 0.7-1 mg/L at intermittent aeration. Based on these findings, we propose a new combined technology of wastewater sludge treatment. The technology combines two stages: anaerobic digestion followed by aerobic biological treatment of digested sludge. The proposed technology makes it possible to degrade the sludge with conversion of approximately 45% volatile suspended solids to biogas, to improve nitrogen and phosphorus removal in reject water from sludge treatment units, and to achieve removal of malodorous substances after 8-9 days of anaerobic-aerobic sludge treatment.     

Phenol wastewater remediation: advanced oxidation processes coupled to a biological treatment.

Nowadays, there are increasingly stringent regulations requiring more and more treatment of industrial effluents to generate product waters which could be easily reused or disposed of to the environment without any harmful effects. Therefore, different advanced oxidation processes were investigated as suitable precursors for the biological treatment of industrial effluents containing phenol. Wet air oxidation and Fenton process were tested batch wise, while catalytic wet air oxidation and H2O2-promoted catalytic wet air oxidation processes were studied in a trickle bed reactor, the last two using over activated carbon as catalyst. Effluent characterisation was made by means of substrate conversion (using high liquid performance chromatography), chemical oxygen demand and total organic carbon. Biodegradation parameters (i.e. maximum oxygen uptake rate and oxygen consumption) were obtained from respirometric tests using activated sludge from an urban biological wastewater treatment plant (WWTP). The main goal was to find the proper conditions in terms of biodegradability enhancement, so that these phenolic effluents could be successfully treated in an urban biological WWTP. Results show promising research ways for the development of efficient coupled processes for the treatment of wastewater containing toxic or biologically non-degradable compounds.