电火花铣削加工工艺与算法研究

介绍了电火花铣削加工工艺及其有关计算方法。在大量实验的基础上,研究了微细电火花分层铣削加工,采用电极底面放电方式、电极轨迹规划、电极的损耗及补偿策略和合理选择分层厚度及电极微进给量等关键技术,提高了加工精度和效率。     

多孔质电极电火花加工方法及实验

为克服传统电火花加工的复杂形状电极制备周期长、大面积复杂型腔加工效率低的弊端,提出了一种用于粗加工的多孔质电极电火花加工新方法。采用紫铜颗粒高温烧结的方式实现多孔质电极的快速制备,利用多孔质电极中的孔隙实现内冲液,以达到电火花粗加工过程中快速去除材料的目的。并可采用电极端部、侧部冲液相结合的方式,提高复杂型腔电火花加工的效率。通过对多孔质电极烧结制备的实验研究,初步确定了多孔质电极的烧结工艺参数。通过加工实验证明了多孔质电极电火花加工的可行性。     

硬质合金模型腔的电火花加工

介绍了硬质合金型腔模电火花加工电极的设计、加工条件的选择、提高加工效率的方法，特别提出了经济电流密度、粗糙度升级等工艺思想。     

注射模电极电火花加工工艺图自动生成技术研究

分析了手工绘制电火花加工工艺图存在的缺点,对电火花加工工艺图的标准化及自动化进行了研究,利用UG二次开发技术,将电极设计过程中涉及到的电极命名规则、电极信息的建立与保存等相互关联,实现了电极命名、电极参数设置及电火花加工工艺图绘制的自动化,有效避免了手工绘图的出错率,在大幅提高电极设计效率的同时,降低了人为错误引起的成本损失。     

油泵油嘴复杂微结构微细电火花铣削加工试验

为解决油泵油嘴复杂微结构加工难题,开展了微细电火花铣削加工试验研究。在改进微细电火花加工机床系统的基础上,介绍了微细电火花铣削加工试验过程,并着重分析电极损耗补偿问题、加工效率问题的解决方法,进而完成油泵油嘴复杂微结构的精密微细电火花加工,总结出保证微细电火花铣削加工质量和加工效率的工艺规律。     

微细电火花伺服扫描加工实验研究

进行微细电火花三维扫描加工时,由于电极损耗相对严重,导致形位公差难以保证和加工效率较低。该研究分析了电火花加工常规的电极损耗补偿方法,提出了基于放电间隙伺服控制进行电极损耗实时补偿的微细电火花三维扫描加工方法。辅助以电极电接触感知工件平面和加工原点,三维结构加工实验显示,采用间隙伺服控制进行电极损耗实时补偿有利于提高扫描加工微三维结构的形位精度和加工效率。     

喷油器流量控制阀板精密复杂微结构微细电火花加工技术

阐述了共轨喷油器流量控制阀板复杂微结构微细电火花加工解决方案,介绍了研制的三头数控微细电火花加工装备,分析了微细电火花铣电极损耗补偿及锥度沟槽、十字槽等加工工艺,总结出保证微细电火花铣削加工质量和效率的工艺规律。     

气液混合功能电极电火花诱导烧蚀高效铣削研究

提出了气液混合功能电极电火花诱导烧蚀铣削加工方法,并进行了针对Cr12的铣削试验,与常规电火花铣削进行对比和分析,发现气液混合烧蚀铣削的加工效率可达96.3 mm3/min,而常规电火花铣削的加工效率仅为6.4 mm3/min.从工件表面微观形貌、能谱及成分分析等方面进行研究,解释了加工效率高的原因.最后研究了不同加工参数下,气液混合功能电极电火花诱导烧蚀铣削加工效率的工艺规律.     

双级带叶冠涡轮盘电火花加工电极优化设计

以某型号双级带叶冠涡轮盘电火花加工电极设计为例,分析了原电极设计的不足。通过改进设计方法,增加了电极厚度,设计了二合一的组合电极。最终,优化了电极的线切割工艺,缩短了安装、找正的时间,提高了加工效率。     

深微孔电火花加工非电参数工艺规律研究

在深微孔电火花加工中,工作液及电极材料等非电参数的选择对加工效率及加工质量有极大的影响,揭示这些非电参数的工艺规律对提高深微孔电火花加工性能有重要的研究意义.利用煤油和去离子水两种工作液,以加工效率为目标,在不同条件下开展工艺试验,得出最适宜的工作液在加工45钢和紫铜材料工件时为去离子水,加工铝合金材料工件时为煤油;利用黄铜丝、钨丝及钼丝3种电极材料,同样以加工效率为目标开展工艺试验,得出最佳电极材料在加工45钢工件时为钨,加工紫铜材料工件时为钨和钼,加工铝合金材料工件时为黄铜.上述研究在深微孔电火花加工中合理选择工作液及电极材料方面做出了有益的探索,其研究成果为深微孔电火花加工高效率、高质量的开展提供了重要的借鉴.     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

新型的治疗阿尔茨海默氏症药物(1-二甲基磷酰基-2,2,2-三氯)-乙基-1-醇烟酸醋对体外神经细胞的作用

目的: 观察本实验室合成的一种治疗阿尔茨海默氏症(AD)的药物(1-二甲基磷酰基-2, 2, 2 -三氯)-乙基^-1-醇烟酸醋(NMF),对体外培养的皮层神经细胞活性的影响以及对海人藻酸(KA)所致的神经损伤的保护作用。方法: 采用体外培养皮层神经元的方法,解剖分离 15 d胚胎小鼠皮层神经细胞, 接种于 96孔板,48 h 后加药并培养 72 h,以 MIT 法 观察 NMF 对小鼠皮层神经细胞活性的影响;同时将接种于 24 孔板的细胞预先给予 NMF,d 3 时加或不加KA处理后,以台盼蓝染色鉴别并计数死、活细胞,可得出细胞的存活率。结果: NMF 明显促进胎鼠皮层神经元活性,其中 NMF1、0. 1、10nmol·L^-1促进神经元活性增殖率分别高达 34.7%、37.4%、36. 7%, NMF 明显促进正常胎鼠皮层神经元存活卒,与对照组比较,10nmol·L^-1 NMF 对皮层神经元的存活率分别提高 39.3%、73.5%。 NMF能显著 对抗 KA 所致的神经元损伤,与 KA 损伤组相比, NMF0.1、10、10nmol·L^-1对损伤皮层神经元的保护率分别为 77.30%、80.10%、84.15%。结论: NMF 明 显促进胎鼠皮层神经元的洁性、提高正常皮层神经元,的存活卒,并能有效地保护KA所致的神经元损伤,提示 NMF 是一种很有潜力的治疗 AD 的药物。     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

THERMODYNAMICS STUDY ON THE DECOMPOSITION OF CHROMITE WITH KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

INFLUENCE OF HEAT TREATMENT ON DAMPING BEHAVIOUR OF THE MAGNESIUM WROUGHT ALLOY AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Theoretical Analysis for the Motion and Temperature of Melt Droplets in Spray Degassing Process

The motion of melt droplets in spray degassing process was analyzed theoretically. The height of the treatment tank in spray degassing process could be determined by the results of theoretical calculation of motion of melt droplets. To know whether the melt droplets would solidify during spraying process, the balance temperature of melt droplets was also theoretically analyzed. Then proof experiments for theoretical results about temperature of melt droplets were carried. In comparison, the experimental results were nearly similar to the calculation results.     

Growth Kinetics of Single Inclusion Particle in Molten Melts

On the basis of the single-particle framework, a new theory on inclusion growth in metallurgical melts is developed to study the kinetics of inclusion growth on account of reaction and collision. The studies show that the early growth of inclusion depends on reaction growth and Brawnian motion collision, and where the former is decisive, the late growth depends on turbulence collision and Stokes＇ collision, and where the former is dominant; collision growth is very quick during the smelting process, lessened in the refining process, but nearly negligible in the continuous casting process.     

Three-Dimensional Growth of Coherent Ferrite in Austenite: A Molecular Dynamics Study

Coherent second phase often exhibits anisotropic morphology with specifi c orientations with respect to both the second and the matrix phases. As a key feature of microstructure, the morphology of the coherent particles is essential for understanding the second-phase strengthening eff ect in various industrial alloys. This letter reports anisotropic growth of coherent ferrite from austenite matrix in pure iron based on molecular dynamics simulation. We found that the ferrite grain tends to grow into an elongated plate-like shape, independent of its initial confi guration. The fi nal shape of the ferrite is closely related to the misfi t between the two phases, with the longest direction and the broad facet of the plate being, respectively, consistent with the best matching direction and the best matching plane calculated via the Burgers vector content(BVC) method. The strain energy calculation in the framework of Eshelby's inclusion theory verifi es that the simulated orientation of the coherent ferrite is energetically favorable. It is anticipated that the BVC method will be applicable in analysis of anisotropic growth and morphology of coherent second phase in other phase transformation systems.     

An Easy Way to Quantify the Adhesion Energy of Nanostructured Cu/X(X=Cr,Ta,Mo,Nb,Zr) Multilayer Films Adherent to Polyimide Substrates

An approach based on film buckling under simple uniaxial tensile testing was utilized in this paper to quantitatively estimate the interfacial energy of the nanostructured multilayer films(NMFs) adherent to flexible substrates. The interfacial energies of polyimide-supported NMFs are determined to be *5.0 J/m2 for Cu/Cr, *4.1 J/m2 for Cu/Ta,*2.8 J/m2 for Cu/Mo, *1.1 J/m2 for Cu/Nb, and *1.2 J/m2 for Cu/Zr NMFs. Furthermore, a linear relationship between the adhesion energy and the interfacial shear strength is clearly demonstrated for the Cu-based NMFs, which is highly indicative of the applicability and reliability of the modified models.     

High-Speed Friction Stir Welding of SiC_p/Al–Mg–Si–Cu Composite

A 17 vol% SiCp/Al–Mg–Si–Cu composite plate with a thickness of 3 mm was successfully friction stir welded(FSWed) at a very high welding speed of 2000 mm/min for the first time. Microstructural observation indicated that the coarsening of the precipitates was greatly inhibited in the heat-affected zone of the FSW joint at high welding speed, due to the significantly reduced peak temperature and duration at high temperature. Therefore, prominent enhancement of the hardness was achieved at the lowest hardness zone of the FSW joint at this high welding speed, which was similar to that of the nugget zone. Furthermore, the ultimate tensile strength of the joint was as high as 369 MPa, which was much higher than that obtained at low welding speed of 100 mm/min(298 MPa). This study provides an effective method to weld aluminum matrix composite with superior quality and high welding efficiency.