LiF插层对有机发光二极管磁场效应的调控

制备了有LiF插层的有机发光二极管,以八羟基喹啉铝（Alq₃）作为电子传输层,N, N′-二苯基-N, N′-二(1-萘基)-1,1′-联苯-4,4′-二胺（NPB）作为空穴传输层.通过改变Alq₃与NPB间LiF插层的厚度,研究了不同温度下器件的光电特性及电致发光的磁场效应.测量结果表明:LiF插层可以影响器件内部载流子的输运和激发态的形成.较厚的插层阻碍了空穴的传输,使器件的电流效率变低.但实验中发现, 关键词： LiF插层结构 磁场效应 三重态激子     

有机发光器件的磁电导效应

制备了基于三(8-羟基喹啉)铝(tris-(8-hydroxyquinoline) aluminum (III), Alq₃) 的有机发光二极管, 并在不同偏压下测量了器件的室温磁电导效应.在小偏压下, 发光器件展示出明显的负磁电导效应.偏压增加后, 磁电导由负值变为正值, 出现了正负转变的现象. N, N'-二苯基-N, N'-(1-萘基)-1, 1'-联苯-4, 4'-二胺(N, N′-Di(naphthalen-1-yl)-N, N′ diphenyl-benzidine, NPB) 与铜酞菁 (Copper phthalocyanine, CuPc) 单极器件磁电导的测量结果表明, 发光器件在小偏压下的负磁电导效应来源于器件中的CuPc层. 双极电流的磁电导效应可用电子-空穴对模型进行解释, 而单极电流的磁电导效应可归因于器件中的极化子-双极化子转变. 在注入电流的变化过程中, 发光器件的正负磁电导转变是两种机理共同作用的结果.     

基于Alq3的有机发光二极管的磁电导效应

制备了结构为 ITO/CuPc/NPB/Alq₃/LiF/Al 的有机发光二极管,并在300,260,220和180 K 四个温度测量了器件在恒压偏置下注入电流的磁场效应(磁电导效应).在注入电流从双极电流过渡到单极电流的过程中,随电流减小,器件的磁电导呈现先上升后下降的变化趋势.当温度降低,磁电导的值下降.但在任何测量条件下,器件的磁电导始终为正,没有出现如文献报道的磁电导从正到负的变化.实验结果表明,有机发光二极管中正负磁电导现象的产生,并非仅取决于注入电流是单极电流还是双极电流,它还与有机材料、器件结构等密切相关.利用受磁场调控的“电子-空穴对”机理与“双极化子”模型,分别解释了器件双极电流和单极电流的正磁电导效应. 关键词： 有机发光二极管 磁电导 双极化子     

典型有机发光二极管中载流子传输和复合模型

提高载流子复合效率是改善有机发光二极管(OLEDs)发光效率的重要方法。采用真空热蒸发成膜法制作了典型双层结构的OLEDs(ITO/TPD/Alq₃/Al)。二极管的性能测试结果表明器件的电流-电压关系与Fow ler-Nordheim场发射载流子注入理论符合得较好。以Fow ler-Nordheim场发射载流子的隧穿注入理论为基础,对OLEDs的电流进行理论分析和数学推导,建立典型双层结构有机发光二极管中载流子传输、复合的理论模型。以此模型为依据,对载流子注入复合进行理论分析,探究载流子注入复合的效率的表达式。在外加电压和器件材料一定下,得出了载流子复合效率与阳极区一侧积累的空穴面密度和阴极区一侧积累的电子面密度的关系表达式。     

磁场对有机电致发光的影响

制备了常规有机发光二极管ITO/NPD/Alq₃/LiF/Al，测量了该器件发光的磁场效应.发现尽管在1T范围内的磁场对发光层Alq₃的光致发光没有影响，但磁场作用下器件的电致发光(MEL)却呈现出明显的磁效应，且MEL与器件的偏压有很强的依赖关系：在小偏压时，随着磁场的增加MEL是单调递增，且在大小约为40kA/m的磁场下达到饱和，之后即使磁场增大到约1T 的情况下也没有变化；但当偏压变大时，MEL则呈现先增加，在40kA/m处达到峰值后却又减弱，而且偏压越大该MEL的减弱则越明显.对所观察到的实验结果进行了定形解释，即三线态激子相互淬灭产生单线态激子和三线态激子与器件中的非平衡载流子相互作用是此效应的物理机理. 关键词： 有机发光 磁场效应 激子淬灭     

有机发光二极管光取出技术研究进展

有机发光二极管(OLED)在通信、信息、显示和照明等领域均显现出巨大的商业应用前景,十几年来一直是光电信息领域的研究热点之一.但是,OLED的外量子效率远低于内量子效率,极大程度地制约了其发展和应用.本文主要介绍了多种有效提高器件效率的光取出技术,对微透镜、光子晶体结构、纳米图案和纳米多孔膜以及微腔技术等多种OLED修饰方法进行了回顾和讨论.在此基础上,对一些光取出技术的研究做了展望.     

调控空穴传输层的分子取向提高有机发光二极管性能

有机发光二极管(OLED)器件性能的提高一直是有机电致发光领域备受关注的研究课题之一,通过优化OLED器件中的载流子平衡是提高OLED器件性能的一个非常重要的手段。但是,调控空穴传输层或电子传输层中的分子取向,从而优化器件中的载流子平衡未被关注。本文通过对空穴传输层进行不同温度的退火处理来改变空穴传输层中的分子取向,研究分子取向对其空穴迁移率和OLED器件性能的影响。研究发现,退火温度的升高使得空穴传输层中具有垂直取向的分子的比例增加,促进了空穴迁移率的提高。当把具有不同分子取向的空穴传输层应用于OLED器件时,可以清楚地观察到载流子平衡因子对器件性能的影响。     

调控空穴传输层的分子取向提高有机发光二极管性能EI北大核心CSCD

有机发光二极管(OLED)器件性能的提高一直是有机电致发光领域备受关注的研究课题之一,通过优化OLED器件中的载流子平衡是提高OLED器件性能的一个非常重要的手段。但是,调控空穴传输层或电子传输层中的分子取向,从而优化器件中的载流子平衡未被关注。本文通过对空穴传输层进行不同温度的退火处理来改变空穴传输层中的分子取向,研究分子取向对其空穴迁移率和OLED器件性能的影响。研究发现,退火温度的升高使得空穴传输层中具有垂直取向的分子的比例增加,促进了空穴迁移率的提高。当把具有不同分子取向的空穴传输层应用于OLED器件时,可以清楚地观察到载流子平衡因子对器件性能的影响。     

Li2CO3电子注入层改善有机发光二极管性能的研究

常规有机发光二极管发光层中载流子浓度的不平衡,导致器件发光亮度、效率等性能不能达到最优.为了改善电子的注入和传输,采用Li2 CO3作为电子注入层,并将其掺入4,7-二苯基-1,10菲啰啉(Bphen)电子传输材料中,研究电子注入和传输能力的变化及其对器件发光性能的影响.结果表明:Li2 CO3作为有效的电子注入层,使...     

高效有机发光二极管的光提取技术及其研究进展

高性能材料研究使有机发光二极管（Organic light-emitting diode,OLED）取得了突飞猛进的发展,但是器件内部生成的光子由于光学损耗无法全部发射到外部空间,从而极大地降低了OLED效率,并阻碍了其在节能照明市场的应用。通过调控光损失区域的波传导,光提取技术能够有效抑制衬底、波导、表面等离子激元等损耗模式,理论上可使效率扩大4倍。具有1.05～2倍扩大效果的光提取技术已被大量报道,但与理论极限仍存在很大差距。为此,本文简要分析了OLED光学损耗模式,综述了近年来高效的、特别是能实现2倍以上扩大效果的光提取技术。     

Non-doped-type white organic light-emitting diodes for lighting purpose

We demonstrate a non-doped white organic light-emitting diode (WOLED) in which the blue-, green- and red-emissions are generated from 4,4′-bis(2,2′-diphenylvinyl)-1,1′-biphenyl, tris(8-hydroxyquinoline)aluminum (Alq) and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyl-julolidyl 9-enyl)-4H-pyran (DCJTB), which is used as an ultrathin layer. The DCJTB ultrathin layer plays the chromaticity tuning role in optimizing the white spectral band by modulating the location of the DCJTB ultrathin layer in the green emissive Alq layer. The optimized WOLED gives the Commission Internationale de l’Eclairage-1931 xy coordinates of (0.319, 0.335), a color rendering index of 91.2 at 10 V, a maximum brightness of 21010 cd/m² at 12 V and a maximum current efficiency of 5.17 cd/A at 6.6 V. The electroluminescence mechanism of the white device is also discussed.     

Ligand effect on the performance of organic light-emitting diodes based on europium complexes

A series of europium complexes were synthesized and their electroluminescent (EL) characteristics were studied. It was found by comparison that the different substituted groups, such as methyl, chlorine, and nitryl, on ligand 1,10-phenanthroline affect significantly the EL performance of devices based on these complexes. The more methyl-substituted groups on ligand 1,10-phenanthroline led to higher device efficiency. A chlorine-substituted group showed the approximate EL performance as two methyl-substituted groups, whereas a nitryl substituent reduced significantly the EL luminous efficiency. However, β-diketonate ligand TTA and DBM exhibited similar EL performance. The improved EL luminous efficiency by proper substituted groups on the 1,10-phenanthroline was attributed to the reduction of the energy loss caused by light hydrogen atom vibration, as well as concentration quenching caused by intermolecular interaction, and the match of energy level between the ligand and Eu³⁺.     

白光有机电致发光器件的载流子传输与复合特性

基于一种将具有电荷传输性的双极性主体材料与蓝、黄光客体材料共蒸的单层结构的同质结结构,制备了色温可调的白光有机电致发光器件(OLED)。由于不存在激子阻挡层,单层结构容易发生漏电流现象,致使OLED器件具有较高的工作电压和较低的电流/功率效率。在空穴/电子传输层进行p/n型掺杂的同质结结构则大大改善了器件性能。研究表明: 该种器件结构获得了相对较低的起压5.6 V,较高的电流效率2.64 cd/A和低效率滚降,其色坐标则随着亮度的增加沿着普朗克轨迹变化,产生类似于太阳光的发光特性。另外,对主体材料和共蒸层的电荷载流子的传输特性和复合机制也进行了一系列分析研究。     

Improved performance of organic light-emitting diodes with dual electron transporting layers

In this study the performance of organic light-emitting diodes(OLEDs) are enhanced significantly,which is based on dual electron transporting layers(Bphen/CuPc).By adjusting the thicknesses of Bphen and CuPc,the maximal luminescence,the maximal current efficiency,and the maximal power efficiency of the device reach 17570 cd/m2 at 11 V,and 5.39 cd/A and 3.39 lm/W at 3.37 mA/cm2 respectively,which are enhanced approximately by 33.4%,39.3%,and 68.9%,respectively,compared with those of the device using Bphen only for an electron transporting layer.These results may provide some valuable references for improving the electron injection and the transportation of OLED.     

White organic light-emitting diodes based on electroplex from polyvinyl carbazole and carbazole oligomers blends

White organic light-emitting diodes with a blue emitting material fluorene-centred ethylene-liked carbazole oligomer (Cz6F) doped into polyvinyl carbazole (PVK) as the single light-emitting layer are reported. The optical properties of Cz6F, PVK, and PVK:Cz6F blends are studied. Single and double layer devices are fabricated by using PVK: Cz6F blends, and the device with the configuration of indium tin oxide (ITO)/PVK:Cz6F/ tris(8-hydroxyquinolinate)aluminium (Alq₃)/LiF/Al exhibits white light emission with Commission Internationale de l'éclairage chromaticity coordinates of (0.30, 0.33) and a brightness of 402~cd/m². The investigation reveals that the white light is composed of a blue--green emission originating from the excimer of Cz6F molecules and a red emission from an electroplex from the PVK:Cz6F blend films.     

High power efficiency in single layer blue phosphorescent organic light-emitting diodes

High efficiency single layer blue phosphorescent organic light-emitting diodes (PHOLEDs) without any charge transport layer were developed. A mixed host of spirobifluorene based phosphine oxide (SPPO13) and 1, 1-bis[(di-4-tolylamino)phenyl]cyclohexane (TAPC) was used as the host in the emitting layer. A high maximum external quantum efficiency of 15.8% and a quantum efficiency of 8.6% at 1000 cd/m² were achieved in the single-layer blue PHOLEDs without any charge transport layer. The maximum power efficiency and power efficiency at 1000 cd/m² were 31.4 and 16.9 lm/W, respectively.     

High efficiency blue phosphorescent organic light-emitting diodes without electron transport layer

High efficiency blue phosphorescent organic light-emitting diodes were fabricated without an electron transport layer using a spirobifluorene based blue triplet host material. The simple blue PHOLEDs without the electron transport layer showed a high external quantum efficiency and current efficiency of 16.1% and 30.2 cd/A, respectively. The high device performances of the electron transport layer free blue PHOLEDs were comparable to those of blue PHOLEDs with the electron transport layer.     

Color tunable high efficiency microcavity organic light-emitting diodes

Color tunable microcavity organic light-emitting diodes (OLEDs) with structure of distributed Bragg reflectors (DBR)/indium-tin-oxide (ITO)/N,N′-di(naphthalene-1-yl)-N,N′-diphenyl-benzidine (NPB)/tris(8-hydroxyquinoline) aluminum (Alq₃)/LiF/Al were fabricated. Orange red and green light emissions with full width at half maximum (FWHM) of less than 20 nm were obtained through simply changing the thickness of NPB layer. Furthermore, due to the effective modification of the spontaneous emission within microcavity, the brightness and electroluminescent (EL) efficiency of the microcavity OLEDs were significantly enhanced. The maximum brightness and current efficiency, respectively, reached 31000 cd/m² at a current density of 480.0 mA/cm² and 8.3 cd/A at a current density of 110.0 mA/cm² for green devices, and 9700 cd/m² at a current density of 180.0 mA/cm² and 6.6 cd/A at a current density of 36.4 mA/cm² for red devices, which are over 1.5 times higher than those of noncavity OLEDs.      

非周期微纳结构增强有机发光二极管光耦合输出的研究进展

有机发光二极管（OLED）具有功耗低、重量轻、色域宽、响应时间快及对比度高等优点,在全彩平板显示和固态照明等领域均显现出巨大的应用潜力,受到人们的广泛关注.然而,较低的光输出效率使得器件的外量子效率远低于内量子效率,这严重制约了OLED器件的发展和应用.因此如何提高OLED器件的光耦合输出效率已成为备受关注的研究课题.本文主要介绍了采用非周期微纳结构提高OLED器件光耦合输出效率的最新研究进展,对随机微纳透镜结构、光散射介质层、聚合物多孔散射薄膜、随机凹凸波纹结构及随机褶皱结构等多种对器件亮度分布和光谱稳定性无明显影响的光耦合输出技术进行了总结和讨论.最后,对提高OLED器件光耦合输出研究做了总结和展望.     

GaN基多量子阱蓝光LED的γ辐照效应

本文用4×104Ci(1Ci=3.7×1010Bq)的60Co源(剂量率2×105rad(Si)/h)对GaN基InGaN/GaN多量子阱蓝光LED进行5种剂量的γ射线的辐照实验.通过辐照前后蓝光LED的波长、色纯度、最大半峰宽(FWHM)和电流-电压(I-V)、电流-光通量(I-F)等电光学特性分析,得到γ射线对GaN基LED器件的辐照效应.结果发现,辐照后LED器件的发光一致性和均匀性变差,在20mA工作电流下,最大剂量下器件发光强度衰减近90%,光通量衰减约40%,并得到器件的抗辐照能力的参数τ0Kγ为4.039×10-7rad.s-1,发现较低的正向偏压下(小于2.6V)器件的饱和电流随辐照总剂量增大而增大.