Surface modification of ultra‐high‐molecular‐weight polyethylene. II. Effect on the physicomechanical and tribological properties of ultra‐high‐molecular‐weight polyethylene/poly(ethylene terephthalate) composites

We performed surface modification of ultra‐high‐molecular‐weight polyethylene (UHMWPE) through chromic acid etching, with the aim of improving the performance of its composites with poly(ethylene terephthalate) (PET) fibers. In this article, we report on the morphology and physicomechanical and tribological properties of modified UHMWPE/PET composites. Composites containing chemically modified UHMWPE had higher impact properties than those based on unmodified UHMWPE because of improved interfacial bonding between the polymer matrix and the fibers and better dispersion of the fibers within the modified UHMWPE matrix. Chemical modification of UHMWPE before the introduction of PET fibers resulted in composites exhibiting improved wear resistance compared to the base material and compared to unmodified UHMWPE/PET composites. On the basis of the morphological studies of worn samples, microploughing and fatigue failure associated with microcracking were identified as the principle wear mechanisms. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

In order to clarify the effect of high molecular weight component on the crystallization of bimodal high density polyethylene (HDPE), a commercial PE-100 pipe resin was blended with small loading of ultra high molecular weight polyethylene (UHMWPE). The isothermal crystallization kinetics and crystal morphology of HDPE/UHMWPE composites were studied by differential scanning calorimetry (DSC) and polarized optical microscopy (POM), respectively. The presence of UHMWPE results in elevated initial crystallization temperature of HDPE and an accelerating effect on isothermal crystallization. Analysis of growth rate using Lauritzen-Hoffman model shows that the fold surface free energy (σ_e) of polymer chains in HDPE/UHMWPE composites was lower than that in neat HDPE. Morphological development during isothermal crystallization shows that UHMWPE can obviously promote the nucleation rate of HDPE. It should be reasonable to conclude that UHMWPE appeared as an effective nucleating agent in HDPE matrix. Rheological measurements were also performed and it is shown that HDPE/UHMWPE composites are easy to process and own higher melt viscosity at low shear rate. Combining with their faster solidification, gravity-induced sag in practical pipe production is expected to be effectively avoided.     

Influence of phase morphology on the sliding wear of polyethylene blends filled with carbon nanofibers

In this work, phase separation in carbon nanofiber (CNF) composites with a blend of ultrahigh molecular weight polyethylene (UHMWPE)/high‐density polyethylene (HDPE) was revealed, and its effects on tribological properties were investigated. Results from morphological analysis by optical and scanning electron microscopy indicated two distinct microstructures: a dispersed UHMWPE phase and a continuous microstructure containing HDPE and CNFs. The addition of CNFs into the UHMWPE/HDPE blend induced a decreased steady‐state torque indicative of a decreased dissolution and improved processability. Because CNFs predominantly resided into the HDPE phase, neat HDPE, a HDPE/CNF composite, and neat UHMWPE samples were also prepared for comparison. Wear results, determined by a pin‐on‐disk apparatus, showed that both initial run‐in and steady‐state wear rates of the UHMWPE/HDPE/CNF nanocomposites were reduced with an increasing concentration of CNFs. The wear resistance of the UHMWPE/HDPE blend was more strongly influenced than neat HDPE by the addition of CNFs, which may have been affected by a reduced dissolution and improved interfacial interaction between the two phases. Results from this study suggested that HDPE may not be appropriate for processing UHMWPE composites, as CNFs reside in the HDPE phase, and HDPE diminishes the wear resistance of the material. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

The effects of hybrid fillers on thermal,mechanical, physical,and antimicrobial properties of ultrahigh‐molecular‐weight polyethylene‐reinforced composites

The effects of hybrid filler of zinc oxide and chitosan (chitosan–ZnO) on thermal, flexural, antimicrobial, chemical resistance, and hardness properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE) composites with varying concentration of zinc oxide (ZnO) and further hybridized by chitosan (CS) were successfully studied. The composites were prepared using mechanical ball milling and followed by hot compression molding. The addition of ZnO to the UHMWPE matrix had lowered the melting temperature (T _m) of the composite but delayed its degradation temperature. Further investigation of dual filler incorporation was done by the addition of chitosan to the UHMWPE/ZnO composite and resulted in the reduction of UHMWPE crystallization. The flexural strength and modulus had a notably high improvement through ZnO addition up to 25 wt% as compared to neat UHMWPE. However, the addition of chitosan had resulted in lower flexural strength than that of 12 wt% ZnO UHMWPE composite but still higher than that of neat UHMWPE. It was experimentally proven that the incorporation of ZnO and chitosan particles within UHMWPE matrix had further enhanced the antimicrobial properties of neat UHMWPE. Chemical resistance was improved with higher ZnO content with a slight reduction of mass change after the incorporation of chitosan. The hardness value increased with ZnO addition but higher incorporation of chitosan had lowered the hardness value. These findings have significant implications for the commercial application of UHMWPE based products. It appears that these hybrid fillers (chitosan–ZnO)‐reinforced UHMWPE composites exhibit superior overall properties than that of conventional neat UHMWPE. POLYM. COMPOS., 38:1689–1697, 2017. © 2015 Society of Plastics Engineers     

Surface modification of ultra‐high‐molecular‐weight polyethylene. I. Characterization and sintering studies

We performed surface modification of ultra‐high‐molecular‐weight polyethylene (UHMWPE) through chromic acid etching with the aim of improving the performance of UHMWPE's composites with poly(ethylene terephthalate) fibers. In part I of this study, we evaluated the effects of chemical modification on the surface properties of UHMWPE with X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), and contact angle measurements. The thermal properties, rheology, and sintering behavior of the modified UHMWPE were compared to those of the base material. XPS and FTIR analysis confirmed the presence of carboxyl and hydroxyl groups on the surface of the modified powders. The substitution of polar groups into the backbone of the polymer decreased its contact angles with water and hexadecane and increased its surface energy, as evidenced by contact angle measurements. The modified UHMWPE was more crystalline than the base resin and less prone to thermal degradation. Although the rheological properties were virtually identical, the modified powders sintered more readily, presumably due to their higher surface energy, which suggested enhanced processability by compression molding. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Surface modification and physical properties of various UHMWPE‐fiber‐reinforced modified epoxy composites

Two surface modification methods—plasma surface treatment and chemical agent treatment—were used to investigate their effects on the surface properties of ultrahigh‐molecular‐weight polyethylene (UHMWPE) fibers. In the analyses, performed using electron spectroscopy for chemical analysis, changes in weight, and scanning electron microscope observations, demonstrated that the two fiber‐surface‐modified composites formed between UHMWPE fiber and epoxy matrix exhibited improved interfacial adhesion and slight improvements in tensile strengths, but notable decreases in elongation, relative to those properties of the composites reinforced with the untreated UHMWPE fibers. In addition, three kinds of epoxy resins—neat DGEBA, polyurethane‐crosslinked DGEBA, and BHHBP‐DGEBA—were used as resin matrices to examine the tensile and elongation properties of their UHMWPE fiber‐reinforced composites. From stress/strain measurements and scanning electron microscope observations, the resin matrix improved the tensile strength apparently, but did not affect the elongation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 655–665, 2007     

Improvement of the tribological behavior of ultra‐high‐molecular‐weight polyethylene by incorporation of poly (phenyl p‐hydroxyzoate)

Ultra‐high‐molecular‐weight polyethylene/poly (phenyl p‐hydroxyzoate) composites (coded as UHMWPE/PPHZ) were prepared by compression molding. The effects of the poly (phenyl p‐hydroxyzoate) on the tribological properties of the UHMWPE/PPHZ composites were investigated, based on the evaluations of the tribological properties of the composites with various compositions and the examinations of the worn steel surfaces and composites structures by means of scanning electron microscopy and transmission electron microscopy. It was found that the incorporation of the PPHZ led to a significant decrease in the wear rate of the composites. The composites with the volume fraction of the PPHZ particulates within 45% ～ 75% showed the best wear resistance. The friction coefficient of the UHMWPE/PPHZ composites decreased with increasing load and sliding velocity, while the wear rates increased with increasing load. This was attributed to the enhanced softening and plastic deformation of the composites at elevated load or sliding velocity. The UHMWPE/PPHZ composites of different compositions had differences in the microstructures and the transfer film characteristics on the counterpart steel surface as well. This accounted for their different friction and wear behaviors. The transfer film of the UHMWPE/PPHZ composites appeared to be thinner and more coherent, which was largely responsible for their better wear resistance of t composite than the UHMWPE matrix. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2336–2343, 2005     

High‐density polyethylene/ultrahigh‐molecular‐weight polyethylene blend. I. The processing,thermal, and mechanical properties

Various blend ratios of high‐density polyethylene (HDPE) and ultrahigh‐molecular‐weight polyethylene (UHMWPE) were prepared with the objective of determining their suitability as biomaterials. Although the presence of HDPE in the blends enabled melt processing, the presence of UHMWPE helped to improve the toughness of the resulting blends. The processability of the blends was investigated with the Brabender torque, which was used as an indication of the optimum blend conditions. The blends were characterized with differential scanning calorimetry. The mechanical tests performed on the blends included tensile, flexural, and impact tests. A 50:50 (w/w) blend yielded optimum properties in terms of the processability and mechanical properties. The tensile property of the 50:50 blend was intermediate between those of HDPE and UHMWPE, but the strain at break increased 200% in comparison with that of both neat resins. The energy at break of the 50:50 blend revealed an improvement in the toughness. The fracture mechanism was also investigated with scanning electron microscopy. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 413–425, 2005     

Mechanical properties of surface‐modified ultra‐high molecular weight polyethylene fiber reinforced natural rubber composites

The mechanical properties of ultra‐high molecular weight polyethylene (UHMWPE) fibers reinforced natural rubber (NR) composites were determined, and the effects of fiber surface treatment and fiber mass fraction on the mechanical properties of the composites were investigated. Chromic acid was used to modify the UHMWPE fibers, and the results showed that the surface roughness and the oxygen‐containing groups on the surface of the fibers could be effectively increased. The NR matrix composites were prepared with as‐received and chromic acid treated UHMWPE fibers added 0–6 wt%. The treated UHMWPE fibers increased the elongation at break, tear strength, and hardness of the NR composites, especially the tensile stress at a given elongation, but reduced the tensile strength. The elongation at break increased markedly with increasing fiber mass fraction, attained maximum values at 3.0 wt%, and then decreased. The tear strength and hardness exhibited continuous increase with increasing the fiber content. Several microfibrillations between the fiber and NR matrix were observed from SEM images of the fractured surfaces of the treated UHMWPE fibers/NR composites, which meant that the interfacial adhesion strength was improved. POLYM. COMPOS., 38:1215–1220, 2017. © 2015 Society of Plastics Engineers     

Effects of stearic acid on the tensile properties of ultrahigh molecular weight polyethylene fibers

For the purpose of the development of ultrahigh molecular weight polyethylene (UHMWPE) fibers with improved tensile properties, the stearic acid (SA) was added to the gel spinning of UHMWPE and acted as a lubricant film. SA addition was intended to be 0.2, 0.4, 0.6, 0.8, and 1.0 wt% of UHMWPE for forming the SA modified UHMWPE fibers. The tensile properties, thermal properties, crystallization properties, and orientation properties of the prepared UHMWPE fibers were systematically investigated. Results show that there is a more significant tensile property for UHMWPE fibers as SA addition is 0.6 wt%. Their tensile strength and tensile modulus reach 32.86 and 1580.89 cN/dtex, which are raised to an extent of 12.0% and 7.7%, respectively, compared with UHMWPE fibers alone. Moreover, the thermal properties, crystallization properties, and orientation properties of the prepared UHMWPE fibers are enhanced observably when the SA addition is 0.6 wt%.     

Investigation of the ultradrawing properties of gel spun fibers of ultra‐high molecular weight polyethylene/carbon nanotube blends

The carbon nanotubes (CNTs) contents, ultrahigh‐molecular‐weight polyethylene (UHMWPE) concentrations and temperatures of UHMWPE, and CNTs added gel solutions exhibited significant influence on their rheological and spinning properties and the drawability of the corresponding UHMWPE/CNTs as‐prepared fibers. Tremendously high shear viscosities (ηs) of UHMWPE gel solutions were found as the temperatures reached 140°C, at which their ηs values approached the maximum. After adding CNTs, the ηs values of UHMWPE/CNTs gel solutions increase significantly and reach a maximum value as the CNTs contents increase up to a specific value. At each spinning temperature, the achievable draw ratios obtained for UHMWPE as‐prepared fibers prepared near the optimum concentration are significantly higher than those of UHMWPE as‐prepared fibers prepared at other concentrations. After addition of CNTs, the achievable draw ratios of UHMWPE/CNTs as‐prepared fibers prepared near the optimum concentration improve consistently and reach a maximum value as their CNTs contents increase up to an optimum value. To understand these interesting drawing properties of the UHMWPE and UHMWPE/CNTs as‐prepared fibers, the birefringence, thermal, morphological, and tensile properties of the as‐prepared and drawn fibers were investigated. Possible mechanisms accounting for these interesting properties are proposed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Size effect of charcoal particles on the properties of bamboo charcoal/ultra‐high molecular weight polyethylene composites

This study was aimed at examining the size effect of charcoal particles on the properties of bamboo charcoal (BC)/ultra‐high molecular weight polyethylene (UHMWPE) composites. Four types of BC with various particle sizes were mixed with UHMWPE using a twin‐screw extruder. It was found that the melting temperature and crystallinity of the composites were slightly decreased with the addition of BC. The incorporation of BC remarkably improved the tensile properties and creep resistance of UHMWPE, and the particle size of BC strongly affected the properties of BC/UHMWPE composites. The BC with lowest particle size exhibited best reinforcement, where the tensile strength and Young's modulus were increased by 385% and 517% compared with neat UHMWPE. The composites with 70 wt % BC possessed conductivities of 16.8, 14.1, 13.5, and 10.9 S/m. The storage modulus and glass transition temperature of the composites also increased with the addition of BC. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45530.     

Evaluation of the tensile properties and thermal stability of ultrahigh‐molecular‐weight polyethylene fibers

The thermal stability of ultrahigh‐molecular‐weight polyethylene (UHMWPE) should be paid attention in its applications, although the fiber has excellent flexible tensile properties. The measurements for two kinds of UHMWPE fibers, Dyneema SK65 (The Netherlands) and ZHF (Beijing, China), were carried out at different annealing temperatures and for different aging times. Experimental and regression analysis results showed that the aging behavior of the fibers followed an exponential attenuation with the annealing temperature and aging time. The critical temperature for the safe use of the fibers was equal to or lower than 70°C and depended on the glass‐transition temperature; this was validated by tensile tests. The difference between the two fibers in the thermal properties resulted from the intrinsic supermolecular structures of the two fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 310–315, 2005     

Mechanical properties study of micro‐ and nano‐hydroxyapatite reinforced ultrahigh molecular weight polyethylene composites

This is a comparative study between ultrahigh molecular weight polyethylene (UHMWPE) reinforced with micro‐ and nano‐hydroxyapatite (HA) under different filler content. The micro‐ and nano‐HA/UHMWPE composites were prepared by hot‐pressing method, and then compression strength, ball indentation hardness, creep resistance, friction, and wear properties were investigated. To explore mechanisms of these properties, differential scanning calorimetry, infrared spectrum, wettability, and scanning electron microscopy with energy dispersive spectrometry analysis were carried out on the samples. The results demonstrated that UHMWPE reinforced with micro‐ and nano‐HA would improve the ball indentation hardness, compression strength, creep resistance, wettability, and wear behavior. The mechanical properties for both micro‐ and nano‐HA/UHMWPE composites were comparable with pure UHMWPE. The mechanical properties of nano‐HA/UHMWPE composites are better compared with micro‐HA/UHMWPE composites and pure UHMWPE. The optimum filler quantity of micro‐ and nano‐HA/UHMWPE composites is found to be at 15 wt % and 10 wt %, separately. The micro‐ and nano‐HA/UHMWPE composites exhibit a low friction coefficient and good wear resistance at this content. The worn surface of HA/UHMWPE composites shows the wear mechanisms changed from furrow and scratch to surface rupture and delamination when the weight percent of micro‐ and nano‐HA exceed 15 wt % and 10 wt %. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42869.     

超高分子量聚乙烯纤维的表面处理

综述了超高分子量聚乙烯（UHMWPE）纤维复合材料界面的重要性,总结了表面改性方法对UHMWPE纤维以及UHMWPE／树脂界面的影响。     

Spinning and drawing properties of ultrahigh‐molecular‐weight polyethylene fibers prepared at varying concentrations and temperatures

The concentrations and temperatures of ultrahigh‐molecular‐weight polyethylene (UHMWPE) gel solutions exhibited a significant influence on their rheological and spinning properties. The shear viscosities of UHMWPE solutions increased consistently with increasing concentrations at a constant temperature above 80°C. Tremendously high shear viscosities of UHMWPE gel solutions were found as the temperatures reached 120–140°C, at which their shear viscosity values approached the maximum. The spinnable solutions are those gel solutions with optimum shear viscosities and relatively good homogeneity in nature. Moreover, the gel solution concentrations and spinning temperatures exhibited a significant influence on the drawability and microstructure of the as‐spun fibers. At each spinning temperature, the achievable draw ratios obtained for as‐spun fibers prepared near the optimum concentration are significantly higher than those of as‐spun fibers prepared at other concentrations. The critical draw ratio of the as‐spun fiber prepared at the optimum concentration approached a maximum value, as the spinning temperature reached the optimum value of 150°C. Further investigations indicated that the best orientation of the precursors of shish‐kebab‐like entities, birefringence, crystallinity, thermal and tensile properties were always accompanied with the as‐spun fiber prepared at the optimum concentration and temperature. Similar to those found for the as‐spun fibers, the birefringence and tensile properties of the draw fibers prepared at the optimum condition were always higher than those of drawn fibers prepared at other conditions but stretched to the same draw ratio. Possible mechanisms accounting for these interesting phenomena are proposed.     

Preparation and properties of polyethylene terephthalate/polyethylene/near infrared reflective pigment composites

Polyethylene terephthalate/high density polyethylene (PET/HDPE) composites containing a near infrared reflective (NIR, nickel antimony titanium yellow rutile) pigment was prepared using ethylene‐glycidyl methacrylate‐vinyl acetate (EGMA‐VA) as a compatibilizer to increase the infrared reflection of PET/HDPE and limit the thermal heat accumulation in light of environmental and energy conservation concerns. HDPE was premixed with NIR to form N‐HDPE masterbatch. A good interfacial bonding between PET matrix and HDPE dispersed phase with the help of compatibilizer was confirmed through Fourier transform‐infrared spectra, scanning electron microscopy, and torque rheometer. For PET/N‐HDPE composites, the major X‐ray diffraction peaks and melting behaviors remained unchanged, indicating the limited alternation of crystalline structure for the composite systems with or without compatibilizer. The observed increment in the crystallization temperature of PET for the investigated PET/N‐HDPE composites was mainly due to the nucleation role of both inorganic NIR and HDPE. Tensile strength and elongation at break for compatibilized cases at various N‐HDPE contents conferred higher values than those of the corresponding counterparts without compatibilizer. Yet, Young's modulus for compatibilized systems was about 40% lower than that for systems without compatibilizer, attributed to the rubbery nature of EGMA‐VA. With the inclusion of NIR into HDPE to form PET/N‐HDPE composites with or without EGMA‐VA compatibilizer, the values of reflectance increased to a great degree. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40830.     

Studies on nonisothermal crystallization of ultra–high molecular weight polyethylene in liquid paraffin

The nonisothermal crystallization kinetics for ultra–high molecular weight polyethylene (UHMWPE) in liquid paraffin (LP) systems was investigated through differential scanning calorimetry (DSC) measurement. The influence of UHMWPE concentration and cooling rate on crystallization mechanism and spherulitc structure as implied by the modified Avrami equation and Mo's analysis was determined, whereas the Ozawa's approach fails to describe the crystallization behaviors of these UHMWPE‐diluent systems. As a result, in the modified Avrami analysis, it was found that the Avrami exponent is constant around five at various concentrations of UHMWPE and cooling rates. Further, the value of F(T) in the Mo's approach increases with the increasing of relative crystallinity and UHMWPE content in the blends. The nonisothermal crystallization kinetics presented here are the first for UHMWPE‐diluent systems. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Chemical surface treatment of ultrahigh molecular weight polyethylene for improved adhesion to methacrylate resins

Ultrahigh molecular weight polyethylene (UHMWPE) has high yield strength and modulus, but is nonpolar and chemically inert. For it to be used as an effective reinforcing agent for composites, methods to make the UHMWPE wettable or capable of reaction with the matrix are critical. In the current work, Spectra 900? (UHMWPE) fibers were surface modified by swelling in p‐xylene with: (1) methylmethacrylate (MMA) monomer; (2) PMMA; (3) camphorquinone (CQ); (4) 3‐methacryloxypropyltrichlorosilane (Cl‐MPS); (5) trimethoxysilyl modified polyethylene, N‐(triethoxysilylpropyl)‐dansylamide (fluorescent silane), or octadecyltrimethoxy silane (OMS), followed by hydrolysis and reaction with Cl‐MPS; and (6) by coating with SiO₂ films followed by reaction with MPS. These modifiers were used to improve wettability and provide sites for chemical interactions with the resin matrix. Beads of resin [60/40 BisGMA‐TEGMA (bis‐phenol A bis‐(2‐hydroxypropyl) methacrylate and tri(ethylene glycol) dimethacrylate)] were light‐cured around the treated fibers and the improvement in adhesion was tested by microbond shear strength (τ) tests. The improvements were comparable to those reported by acid etching and plasma treatments. The OMS, fluorescent silane, and SiO₂/Cl‐MPS treatments yielded the best results, that is fourfold increases in τ compared with untreated fibers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1564–1572, 2005     

Properties of bamboo flour/high-density polyethylene composites reinforced with ultrahigh molecular weight polyethylene

In order to improve the properties of bamboo-plastic composites (BPCs), bamboo flour/high-density polyethylene (HDPE) composites were reinforced with ultrahigh molecular weight polyethylene (UHMWPE). The effects of UHMWPE on properties of composites were studied. The crystallinity of composites decreased slightly. Compared with non-UHMWPE added bamboo powder/HDPE composite, the composite with 6 wt % UHMWPE, showed decrease in water absorption to 0.41%, whereas its tensile strength and flexural strength increased to 34.51 and 25.88 MPa, respectively, a corresponding increase of 34.59 and 12.87%. The temperatures corresponding to initial degradation temperature (T_initial) and maximum degradation temperature (T_max) of the composite increased from 282.7 and 467.4 °C to 288.5 and 474.7 °C respectively. Scanning electron microscopic images showed that UHMWPE was well dispersed and fully extended as long fibers in the composite, forming a “three-dimensional physically cross-linked network structure,” which contributed to the improved properties of the composites. © 2020 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48971.