AB／C型嵌段共聚物／均聚物的共混体系的相容性和形态研究（Ⅲ）──共混物的焓弛豫

嵌段共聚物ＰＩ－ｂ－ＰＭＭＡ和不同羟基含量的改性聚苯乙烯ＰＳ（ＯＨ）组成的共混物因ＰＭ－ＭＡ嵌段和ＰＳ（ＯＨ）间的玻璃化转变相当接近而不能用通常的ＤＳＣ法判别其相容性。通过共混物的焓弛豫，得到相容性明确的ＤＳＣ判据，且与电镜观察结果一致。共混物中的Ｔｇ增宽效应可通过江明等提出的链密度梯度模型解释。     

聚氯乙烯／线性低密度聚乙烯共混体系的相容性

用动态力学分析（ＤＭＡ）和傅利叶变换红外光谱（ＦＴＩＲ）研究了氢化聚丁二烯－ｂ－聚甲基丙烯酸甲酯（ＨＰＢＤ－ｂ－ＰＭＭＡ）共聚物增容剂对聚氯乙烯（ＰＶＣ）与线性低密度聚乙烯（ＬＬＤＰＥ）共混体系的增容作用．增容剂使共混物中两相的玻璃化温度发生变化，说明其相容性增加．ＦＴＩＲ的结果表明，增容剂中羰基与ＰＶＣ的α氢形成氢键，使ＣＯ，Ｈ─Ｃ及Ｃ─Ｃｌ的振动频率变化，峰形加宽．     

AB／C型嵌段共聚物／均聚物的共混体系的相容性和形态研究（…

嵌段共聚物ＰＩ－ｂ－ＰＭＭＡ和不同羟基含量的改性聚苯乙烯ＰＳ（ＯＨ）组成的共混物因ＰＭ－ＭＡ嵌段和ＰＳ（ＯＨ）的玻璃化转变相当接近而不能用通常的ＤＳＣ法判别其相容性，通过共混物的焓弛豫，得到相容性明确的ＤＳＣ判据，且与电镜观察结果一致，共混物的Ｔｇ增宽效应可通过江明等提出的链密度梯度模型解释。     

异戊二烯/甲基丙烯酸甲酯嵌段共聚物的合成与微结构研究

用稀土催化剂ＲＥ（Ｐ２０４）３ （ｉ Ｂｕ）３Ａｌ ＢｒＣＨ２ＣＨ２Ｂｒ（ＲＥ＝Ｎｄ,Ｐｒ,Ｙ等）合成嵌段共聚物Ｐ（ＩＰ ｂ ＭＭＡ）．系统考察了共聚合反应特征,以ＤＳＣ,１Ｈ ＮＭＲ,１３Ｃ ＮＭＲ技术研究了该嵌段共聚物的微结构．发现以二溴乙烷为添加剂的稀土催化体系是制备Ｐ（ＩＰ ｂ ＭＭＡ）的良好催化剂,共聚物含２个玻璃化转变温度,分别为－７５６℃和１２９℃,嵌段共聚物的结构规整,（ＩＰ）ｍ段以ｃｉｓ １,４结构为主,其含量为９７％左右,３,４ 结构为３％左右,链节间以头 尾方式连接．（ＭＭＡ）ｎ段以间同立构为主,其含量达７４％．     

PP－g－PMMA在PP／PVDF共混体系中的应用

利用聚丙烯等离子体接枝甲基丙烯酸甲酯共聚物（ＰＰ－ｇ－ＰＭＭＡ）作增容剂，研究了其在聚丙烯／聚偏氟乙烯（ＰＶＤＦ）共混体系中的作用。增容是通过ＰＭＭＡ与ＰＶＤＦ的偶极－偶极相互作用实现的。接枝共聚物使共混体系的抗张强度和模量均有提高，由不同等离子体处理时间所得的ＰＰ－ｇ－ＰＭＭＡ，接枝率在７．７％～３００％具有最好的增容效果；而由不同后聚合时间所得的共聚物，接枝率在３０％～８０％具有最好的增容效果。     

聚二甲基硅氧烷／聚氨酯共混体系的增容作用（I）

采用二甲基硅氧烷－ｂ－乙二醇嵌段共聚物（ＤＭＳ－ｂ－ＯＥ）对聚二甲基硅氧烷／聚氨酯（ＰＤＭＳ／ＰＵ）共混体系的增容，重点研究了增容共混体系的微观形态结构和软科学性能之间的关系。扫描电子显微镜、动态力学分析和力学性能测试结果表明：ＤＭＳ－ｂ－ＯＥ对ＰＤＭＳ／ＰＵ具有优良的增容作用，改善了ＰＤＭＳ／ＰＵ共混体系的相容性，提高了该共混物的力学性能。其抗张强度由３．４ＭＰａ提高到７．６ＭＰａ。     

（PSF—PDMS—PHS）n／PSF共混物的相容性及表面组成

利用ＤＳＣ、ＤＭＡ、ＴＥＭ和ＸＰＳ对［ＰＳＦ－ＰＤＭＳ－ＰＨＳ］ｎ／ＰＳＦ共混物的相容性及表面组成进行了研究．结果表明，ＰＤＭＳ在共混物表面的富集与ＰＳＦ均聚物和［ＰＳＦ－ＰＤＭＳ－ＰＨＳ］ｎ中硬段的相容性有关；ＰＤＭＳ在相容的共混物体系表面的富集与对应的多嵌段共聚物组成基本相近；不相容共混物体系表面ＰＤＭＳ的富集程度相对较高，当共混物本体中有机硅含量从１％增至５％，表面层ＰＤＭＳ的含量迅速增加，可达到嵌段共聚物中ＰＤＭＳ的含量．     

POM／EVA共混物的研究

用力学测试、扫描电镜（ＳＥＭ）、热分析（ＤＳＣ）等手段研究了聚甲醛（ＰＯＭ）与乙烯－醋酸乙烯酯共聚物（ＥＶＡ）共混物（ＰＯＭ／ＥＶＡ）的力学性能及其微同形态；用聚甲醛与马来酸二丁酯（ＤＢＭ）的接枝物（ＰＯＭ－ｇ－ＤＢＭ）作相溶剂，能改变共的两相间的粘结力，从而提出了共混物的力学性能，ＳＥＭ观察表明接枝物的加入改变了ＰＯＭ／ＥＶＡ共混物的断裂方式，微观形态及结晶性能，对其热性能影响不大；通过改变ＰＯ     

苯乙烯-2-乙烯基吡啶两嵌段共聚物的合成与表征

采用阴离子聚合技术合成了一系列苯乙烯 ２ 乙烯基吡啶的两嵌段共聚物（ＰＳ ｂ Ｐ２ＶＰ），并采用ＧＰＣ、ＦＴＩＲ、ＮＭＲ（１Ｈ ＮＭＲ和１３Ｃ ＮＭＲ）、ＤＭＡ等手段进行了表征．结果表明，产物为高分子量、窄分布的两嵌段共聚物，具有微相分离的两相结构     

用SN型催化剂合成苯乙烯－丙烯嵌段共聚物的研究II．共聚物的结构表征与性能

报道用稀土化合物改性的钛系截体催化剂（ＳＮ催化剂）进行苯乙烯和丙烯顺序嵌段共聚合（Ｓｅｑｕｅｎｔｉａｌｂｌｏｃｋｃｏｐｏｌｙｍｅｒｉｚａｔｉｏｎ）的研究，通过对初生嵌段共聚产物进行溶剂萃取与分级，并用１３Ｃ－ＮＭＲ、ＷＡＸＤ．ＤＳＣ，ＤＭＡ和电子显微镜进行表征，推断共聚物为具有等规聚苯乙烯链和等规聚丙烯链段的Ａ－Ｂ型二嵌段共聚物，且各段均能结晶。发现嵌段共聚物比相应的均聚物具有较好的综合力学性能和热性能，而且对ｉＰＳ／ｉＰＰ共混具有良好的增容作用。     

Structure of reactively extruded rigid PVC/PMMA blends

A novel route for producing polymer blends by reactive extrusion is described, starting from poly (vinyl chloride)/methyl methacrylate (PVC/MMA) dry blend and successive polymerization of MMA in an extruder. Small angle X‐ray scattering (SAXS) measurements were applied to study the monomer's mode of penetration into the PVC particles and to characterize the supermolecular structure of the reactive poly(vinyl chloride)/poly(methyl methacrylate) (PVC/PMMA) blends obtained, as compared to the corresponding physical blends of similar composition. These measurements indicate that the monomer molecules can easily penetrate into the PVC sub‐primary particles, separating the PVC chains. Moreover, the increased mobility of the PVC chains enables formation of an ordered lamellar structure, with an average d‐spacing of 4.1 nm. The same characteristic lamellar structure is further detected upon compression molding or extrusion of PVC and PVC/PMMA blends. In this case the mobility of the PVC chains is enabled through thermal energy. Dynamic mechanical thermal analysis (DMTA) and SAXS measurements of reactive and physical PVC/PMMA blends indicate that miscibility occurs between the PVC and PMMA chains. The studied reactive PVC/PMMA blends are found to be miscible, while the physical PVC/PMMA blends are only partially miscible. It can be suggested that the miscible PMMA chains weaken dipole–dipole interactions between the PVC chains, leading to high mobility and resulting in an increased PVC crystallinity degree and decreased PVC glass transition temperature (T_g). These phenomena are shown in the physical PVC/PMMA blends and further emphasized in the reactive PVC/PMMA blends. Copyright © 2005 John Wiley & Sons, Ltd.     

Development and characterization of reactive extruded PVC/polyacrylate blends

This paper describes a method to obtain polymer blends by the absorption of a liquid solution of monomer, initiator, and a crosslinking agent in suspension type porous poly(vinyl chloride) (PVC) particles, forming a dry blend. These PVC/monomer dry blends are reactively polymerized in a twin‐screw extruder to obtain the in situ polymerization in a melt state of various blends: PVC/poly(methyl methacrylate) (PVC/PMMA), PVC/poly(vinyl acetate) (PVC/PVAc), PVC/poly(butyl acrylate) (PVC/PBA) and PVC/poly(ethylhexyl acrylate) (PVC/PEHA). Physical PVC/PMMA blends were produced, and the properties of those blends are compared to reactive blends of similar compositions. Owing to the high polymerization temperature (180°C), the polymers formed in this reactive polymerization process have low molecular weight. These short polymer chains plasticize the PVC phase reducing the melt viscosity, glass transition and the static modulus. Reactive blends of PVC/PMMA and PVC/PVAc are more compatible than the reactive PVC/PBA and PVC/PEHA blends. Reactive PVC/PMMA and PVC/PVAc blends are transparent, form single phase morphology, have single glass transition temperature (T_g), and show mechanical properties that are not inferior than that of neat PVC. Reactive PVC/PBA and PVC/PEHA blends are incompatible and two discrete phases are observed in each blend. However, those blends exhibit single glass transition owing to low content of the dispersed phase particles, which is probably too low to be detected by dynamic mechanical thermal analysis (DMTA) as a separate T_g value. The reactive PVC/PEHA show exceptional high elongation at break (～90%) owing to energy absorption optimized at this dispersed particle size (0.2–0.8 µm). Copyright © 2005 John Wiley & Sons, Ltd.     

SAN共聚物组成对PVC/ABS共混物相容性的影响

采用乳液聚合技术通过改变共聚单体的投料比(St/AN)合成了一系列不同AN结合量的ABS接枝共聚物粉料和SAN共聚物.将其与聚氯乙烯(PVC)和邻苯二甲酸二辛酯(DOP)熔融共混分别制得了PVC/ABS、PVC/SAN、PVC/ABS/DOP和PVC/SAN/DOP共混物,利用SEM、TEM和动态力学粘弹谱仪(DMA)对共混物的相容性和相结构进行了表征.结果发现,在PVC/ABS共混体系中,尽管改变接枝SAN共聚物的AN结合量,PVC和SAN共聚物均为不相容体系;在该共混物中引入增塑剂DOP后,虽然当SAN共聚物AN结合量小于23.4 wt%时,共混物在室温以上只存在一个tanδ峰,但形态结构研究结果表明共混物仍为不相容体系,共混物的相区尺寸明显地依赖于SAN共聚物中的AN结合量,当AN结合量为23.4 wt%时相区尺寸最小.     

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with poly(butadiene-block-methyl methacrylate)

Compatibilization of blends of polybutadiene and poly(methyl methacrylate) with butadiene-methyl methacrylate diblock copolymers has been investigated by transmission electron microscopy. When the diblock copolymers are added to the blends, the size of PB particles decreases and their size distribution gets narrower. In PB/PMMA7.6K blends with P(B-b-MMA)25.2K as a compatibilizer, most of micelles exist in the PMMA phase. However, using P(B-b-MMA)38K as a compatibilizer, the micellar aggregation exists in PB particles besides that existing in the PMMA phase. The core of a micelle in the PMMA phase is about 10 nm. In this article the influences of temperature and homo-PMMA molecular weight on compatibilization were also examined. At a high temperature PB particles in blends tend to agglomerate into bigger particles. When the molecular weight of PMMA is close to that of the corresponding block of the copolymer, the best compatibilization result would be achieved. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36 : 85–93, 1998     

Modification of EVOH copolymers with ϵ‐caprolactone: synthesis and compatibilization effects in PE/PVC blends

Polyethylene‐polycaprolactone graft copolymers with different chemical structures (i.e. different number and length of PCL grafts and molecular weight of PE backbone) were synthesized from various EVOH copolymers and ϵ‐caprolactone, using Aluminum isopropoxide as catalyst, and were tested for their compatibilizing capability in PE/PVC blends. PE and PCL segments in the graft copolymers were found completely immiscible, while PCL segments of the graft copolymers were found completely miscible with PVC. When graft copolymers were added to PE/PVC blends they proved to be good agents for the dispersion of PVC phase in the PE matrix. SEM showed also improved adhesion between the dispersed PVC phase and PE matrix. Moderate improvements in mechanical properties were also observed in preliminary tensile tests.     

Thermal degradation of poly(vinyl bromide), vinyl bromide-methyl methacrylate copolymers,and poly(vinyl bromide)-poly(methyl methacrylate) blends

Degradation behavior has been compared for PVB, five VB-MMA copolymers which span the composition range, PMMA, and PVC by using thermogravimetry in dynamic nitrogen and thermal volatilization analysis (TVA) under vacuum for programmed heating at 10°C/min. Volatile products have been separated by subambient TVA and identified. PVB is substantially less stable than PVC but shows inmost respects analogous degradation behavior. The introduction of VB into the PMMA chain leads to intramolecular lactonization with release of methyl bromide at temperatures a little above 100°C; after this reaction is complete, however, the polymer is more stable toward volatilization than PMMA. Copolymers with moderate and high VB contents also lose hydrogen bromide. Carbon dioxide is a significant product at intermediate compositions. The variation of product distribution with copolymer composition is discussed in relation to the several reactions involved and comparisons are made with VC-MMA copolymers. PVB-PMMA blends snow some features of degradation behavior in common with the PVC-PMMA system but also very important differences. The effect of PVB is only to stabilize the PMMA; the mechanism is discussed. The role of PVB as an additive and VB as a comonomer for fire-retardant PMMA compositions is briefly considered in relation to earlier studies.     

PS-b-PMMA对PVC/SBS共混体系界面结构的影响

在两种不相容的聚合物组成的共混体系中加入增容剂，可以显著提高共混体系的力学性能．目前的理论解释是嵌段共聚物在不相容的聚合物间形成界面层，通过降低组分间的界面张力、增强界面粘接力达到增容目的［‘－‘1．但是这一假设缺乏直接的实验证据．本文利用透射电子显微镜，     

Effect of molecular interactions on the miscibility and structure of polymer blends

The effect of polymer-polymer interactions on the miscibility and macroscopic properties of PVC/PMMA, PVC/PS and PMMA/PS blends were studied in the entire composition range. The miscibility of the components was characterized by the Flory-Huggins interaction parameter or by quantities related to it. Thermal analysis, light transmittance measurements, and scanning electron microscopy were carried out on the blends and their mechanical properties were characterized by tensile tests. Interactions were analyzed by infrared spectroscopy and contact angle measurements. All three polymer pairs form heterogeneous blends, but the strength of molecular interactions is different in them, the highest is in PVC/PMMA system resulting in partial miscibility of the components and beneficial mechanical properties. The structure of these blends depends strongly on composition. A phase inversion can be observed between 0.5 and 0.6 PMMA content accompanied with a significant change in structure and properties. The PVC/PS and the PMMA/PS pairs are immiscible, though the results indicate the partial solubility of the components. The analysis of the surface characteristics of the components and the comparison of quantities derived from them with miscibility as well as with the macroscopic properties of blends revealed that blend properties cannot be predicted in this way, since they are affected by several factors.     

Poly(trialkylsilyl methacrylate)s: A family of hydrolysable polymers with tuneable erosion profiles

Polymers containing hydrolytically labile trialkylsilyl ester side groups were synthesised via a conventional and a controlled radical polymerization. The trialkylsilyl methacrylate monomer unit was chosen for its capacity to hydrolyse into basic, acid or sea water varying the hydrophilic character of the resulting polymer backbone with time. The hydrolysis or saponification reaction of the ester bond of the trialkylsilyl methacrylate was monitored through a ¹H NMR study showing the formation of siloxane side-products. Several copolymers and polymer blends were prepared as matrixes for controlled erodible systems. Their capacity to hydrolyse was demonstrated through SEM investigations with selective dissolution of free films containing hydrolysable copolymers and PMMA blends. Well-defined random and diblock copolymers with methyl methacrylate were investigated to show the effect of the microstructure on the erosion properties of the corresponding coatings. Poly(methyl methacrylate-b-tert-butyldimethylsilyl methacrylate) diblock copolymers synthesised through the RAFT process showed a better control of the erosion with a constant erosion rate over a long-time service in sea water at pH = 8.2. In addition, experiments showed that the erosion rate could be modulated by varying the molar proportion of hydrolysable side groups onto the copolymer backbone and the weight amount of copolymers mixed with PMMA in toluene solution.