Preparation of manganese dioxide loaded activated carbon adsorbents and their desulfurization performance

Manganese dioxide loaded activated carbon adsorbents (MnO₂/AC) were prepared and characterized by N₂ adsorption-desorption, BET method, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectrometry (FT-IR) and scanning electron microscopy (SEM). Effects of preparation conditions and adsorption conditions on desulfurization performance of the adsorbents were studied in a fixed-bed adsorption apparatus. Experimental results show that the surface area and pore volume of MnO₂/AC decreased compared with the unmodified activated carbon, but the adsorption capacity to H₂S was improved greatly. A suitable H₂S removal activity was obtained with manganese dioxide to activated carbon ratio of 1.1: 1 and the calcination temperature of 250°C. At the adsorption temperature of 40°C and gas flow rate of 20 mL/min, the H₂S saturation capacity and H₂S removal rate reached up to 713.25 mg/g and 89.9%, respectively.     

Preparation of a kind of mesoporous carbon and its performance in adsorptive desulfurization

Carbon materials were prepared using mesoporous silica HMS with different pore sizes as the hard templates and water-soluble phenolic resin as the carbon source. The obtained materials were characterized by powder X-ray diffraction, transmission electron microscopy and N₂ physical adsorption, and were used in adsorptive desulfurization. It has been shown that the carbon material prepared using HMS with larger pore size (>3 nm) presented uniform wormlike mesopore of 2.3 nm and large BET surface area (1903 m²/g). The mesoporous carbon was an excellent adsorbent to remove the refractory sulfur compound in diesel, especially dibenzothiophene and 4, 6-dimethyldibenzothiophene.     

汽油活性炭基脱硫吸附剂的制备与评价

以250℃温度下浓硫酸改性后的活性炭为载体,采用浸渍法制备了以MnO₂为活性组分的活性炭基的汽油脱硫吸附剂MnO₂/AC,考察了吸附剂的制备条件及脱硫条件对脱硫效果的影响。研究结果表明,适宜的吸附剂制备条件为,以Mn(NO₃)₂为活性组分前驱物,Mn(NO)₂浸渍液浓度0.15mol/L、常温下浸渍24h、焙烧温度350℃、焙烧时间2h。该吸附剂在静态吸附温度120℃、吸附时间2h、剂油质量比0.10的条件下可使原料油硫的质量分数从628.6×10^-6降至221.5×10^-6,脱硫率达到64.8%;在动态吸附温度60℃、空速1.76h^-1的条件下,初始流出汽油硫的质量分数降至21.8×10^-6,初始脱硫率达到96.5%。     

基于石墨化炭黑预涂覆技术的色谱柱制备和性能评价

采用石墨化炭黑(GCB)预涂覆技术对白酒分析专用色谱柱(LZP-930)的制备方法进行了优化,详细考察了所制备的色谱柱(LZP-930G)的性能参数,并对LZP-930G色谱柱的保留行为进行了评价,探讨了GCB对LZP-930G色谱柱性能的影响。研究发现,LZP-930G色谱柱的柱效、惰性、稳定性和极性均得到了明显提高,从而改善了酸类和醇类组分的分离选择性和色谱峰峰形,实现了白酒中53种易挥发和半挥发性微量组分的同时分离,且各组分的保留时间和峰面积的相对标准偏差分别小于0.63%和4.51%(n=5)。表明GCB预涂覆技术能够用于高性能白酒分析色谱柱的制备方法。     

Preparation of novel porous carbon spheres from corn starch

Irregular porous carbon spheres were successfully prepared from Na₂SnO₃ coated corn porous starch by carbonization. The product was characterized with X-ray diffraction and scanning electron microscope (SEM). It is verified that the irregular porous carbon spheres are composed of disordered carbon, and the skeleton and pores of the corn porous starch was well preserved after carbonization. The pore size of the irregular porous carbon spheres is almost the same, which is similar to that of the porous starch. And the pore size decreases from about 0.91 μm to 0.53 μm measured from the SEM pictures. The texture of the irregular porous carbon spheres is mainly determined by that of porous starch.     

一步法制备含W介孔碳材料及其氧化脱硫性能研究

以钨酸钠为钨源,以乙二胺四乙酸二钠为碳源经过高温煅烧制备了含W的介孔碳材料,采用XRD、SEM、FT-IR、BET对含钨的介孔碳材料进行表征。结果表明,煅烧后介孔碳材料的表面形成了粒状含有结晶水的氧化钨(WO_3·H_2O)。相比于纯的介孔碳材料,含钨介孔碳材料的总比表面积减小。以含W介孔碳材料为催化剂,H_2O_2作为氧化剂,1-丁基-3-甲基咪唑氟硼酸盐([BMIM][BF_4])离子液体作为萃取剂,组成萃取-催化氧化脱硫体系(ECODS)并研究其对模拟油中二苯并噻吩脱除效果。考察了氧化钨负载量、反应温度、H_2O_2加入量、催化剂用量、离子液体用量以及不同类型硫化物对二苯并噻吩脱除的影响。在最佳反应条件下,催化剂对二苯并噻吩(DBT)、4,6-二甲基二苯并噻吩(4,6-DMDBT)、苯并噻吩(BT)、噻吩(TH)和真实汽油的脱除率分别达到98.6%、65.6%、61.2%、57.8%和64.3%。催化剂回收利用五次之后脱硫率略有降低,仍高达95.2%。     

Resorcinol-formaldehyde carbon spheres/polyaniline composite with excellent electrochemical performance for supercapacitors

Well-dispersed resorcinol-formaldehyde-based carbon spheres (RFCs) have been prepared by the polycondensation of resorcinol and formaldehyde with ammonia as catalyst and subsequent carbonization of the obtained polymer. In situ polymerization of the aniline occurred in the suspension of the RFC, and RFC was surrounded by the polyaniline (PANI) wires. The PANI and RFC hybrid network (PRFC) formed gradually. In a three-electrode mode, the specific capacitance (C _sp) of PRFC reaches 315 F g^?1 at a current density of 1 A g^?1 in 2 M H₂SO₄, much higher than that of pure PANI (225 F g^?1) and RFC (121.7 F g^?1). Furthermore, the C _sp of PRFC retains 80.0 % after 1000 charge-discharge processes at a current density of 5 Ag^?1. The enhanced electrochemical performance of the PRFC came from its homogeneous three-dimensional hierarchical network structure, good electric conductivity of the PANI around the RFC, and the synergistic effect between the RFC and PANI.     

载铜球形活性炭的制备及其吸附脱硫性能的研究

以122型弱酸性酚醛系阳离子交换树脂为炭前驱体,经过Cu²⁺交换、炭化和CO₂活化等过程制备得到负载金属铜的球形活性炭,对其进行了SEM、XRD、AAS和BET表征,采用动态吸附实验研究了其对模拟汽油中噻吩类硫化物的吸附性能,并且考察了甲苯和环己烯对其吸附性能的影响,对吸附脱硫机理进行了初步研究。结果表明,载铜球形活性炭上Cu以单质形态存在,并主要与硫原子产生配位作用,提高了对噻吩类硫化物的吸附性能,对噻吩(T)、3-甲基噻吩(MT)、2,5-二甲基噻吩(DMT)和苯并噻吩(BT)的饱和硫容依次为0.938、1.230、1.581和3.744 mg/g,吸附选择性依次为T < MT < DMT < BT。模拟汽油中加入甲苯和环己烯后,饱和硫容分别下降了77%和56%,这是甲苯和环己烯通过π电子与Cu发生作用,从而与硫化物产生竞争吸附导致的。     

高结晶氮化碳空心球的制备及其增强光催化产氢活性

石墨烯型氮化碳(g-C3N4)已经成为解决环境污染和能源危机问题的较为理想的光催化剂,但由于其较低的比表面积和较高的光生载流子重组效率而表现出较弱的光催化活性.因此,研究者们已经提出了许多策略,例如纳米结构设计,杂原子掺杂和增加结晶度,用来克服氮化碳的这些缺点,从而提高其光催化性能.其中,引起了较多关注的是增加g-C3...     

利用胶体碳球为模板制备SiO2、TiO2、SnO2空心球

介观尺度的氧化物空心球材料在许多领域都有着潜在的应用价值[1],因此近年来受到人们的广泛关注。其制备方法包括:模板法[2],声化学法[3],水热法[4]等。其中胶体粒子模板合成是制备氧化物空心球材料的一条最为有效的途径。常见的胶体粒子有金、银、CdS的纳米粒子,介观尺度的SiO     

二苯并噻吩分子印迹复合膜的制备及脱硫性能的研究

聚丙烯中空纤维膜经多巴胺氧化、硅烷化两步表面改性处理后,以甲基丙烯酸为功能单体进行表面分子印迹聚合,制备了中空纤维膜支撑-二苯并噻吩分子印迹复合膜(MIP-PP膜)。利用红外光谱、扫描电镜对印迹复合膜形态结构进行表征,测定了MIP-PP膜的脱硫性能。结果表明,在298 K时,MIP-PP膜对DBT的吸附在180 min达到平衡,最大吸附容量为133.32 mg/g;MIP-PP膜对DBT的吸附符合Lagergren准一级动力学模型及Langmuir吸附等温线,是可自发进行的放热过程。     

Hydrothermal carbon spheres containing silicon nanoparticles: synthesis and lithium storage performance

Spherically shaped carbon/silicon nanocomposites have been obtained in a one-step procedure using hydrothermal carbonization of glucose in the presence of commercially available silicon nanoparticles and have been tested electrochemically as an anode material for lithium-ion batteries.     

Porous carbon and carbon composite hollow spheres

In this communication, we propose a template approach toward synthesis of carbon hollow spheres by direct carbonization of highly crosslinked sulfonated polystyrene gel hollow spheres (sPS). The sulfonic acid group can facilitate carbonization. Moreover, the acid group can also induce a favorable growth of other materials within the sPS gel-forming carbon-based composite shell such as bi-continuous C/SiO₂ and their derivative ceramic SiC. Release of small molecules during polymers decomposition results porous shell.     

DESs/SG催化剂的制备及其氧化脱硫性能

通过溶胶-凝胶法将脯氨酸基低共熔溶剂负载到硅胶上制得DESs/SG型催化剂。采用FT-IR、XRD、SEM/EDS及N₂吸附-脱附等手段对催化剂的结构进行表征。结果发现,低共熔溶剂可以成功负载到硅胶中,硅胶的比表面积和孔体积有所下降,而孔径增大。以DESs/SG为吸附剂和催化剂,H₂O₂为氧化剂,研究其对模拟油中的二苯并噻吩的脱除性能,考察了低共熔溶剂负载量、反应温度、n(H₂O₂)/n(S)比、催化剂用量、含硫化合物的类型以及催化剂循环使用次数对脱硫效率的影响。结果表明,在最优脱硫条件下,DESs/SG对二苯并噻吩、4,6-二甲基二苯并噻吩和苯并噻吩的脱硫率分别为97%、96. 5%和46. 4%;催化剂循环使用九次后,催化脱硫效率仍高达89. 4%。     

壳聚糖基多孔碳材料的制备及其超级电容性能

以胶态SiO₂纳米粒子为模板,壳聚糖为碳源,ZnCl₂为活化剂,制备了具有不同比表面积和孔体积的氮掺杂介孔碳。采用多种表征手段对碳材料的微观形貌、比表面积和孔道结构进行了表征,探究了壳聚糖与SiO₂纳米粒子的比例以及ZnCl₂活化剂对碳材料孔体积和比表面积的影响。结果表明,在未使用活化剂时碳材料(CSi-1.75)的孔体积高达4.53 cm³·g^-1,但其比表面积最小(729 m²·g^-1);使用ZnCl₂作为活化剂制备的碳材料(CSi-1.75-Zn)比表面积为1 032 m²·g^-1,但其孔体积下降到1.99 cm³·g^-1,且具有最多的吡啶氮和吡咯氮。在以6.0 mol·L^-1KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时,CSi-1.75...     

壳聚糖基多孔碳材料的制备及其超级电容性能

以胶态SiO₂纳米粒子为模板,壳聚糖为碳源,ZnCl2为活化剂,制备了具有不同比表面积和孔体积的氮掺杂介孔碳。采用多种表征手段对碳材料的微观形貌、比表面积和孔道结构进行了表征,探究了壳聚糖与SiO₂纳米粒子的比例以及ZnCl2活化剂对碳材料孔体积和比表面积的影响。结果表明,在未使用活化剂时碳材料(CSi-1.75)的孔体积高达4.53 cm³·g^-1,但其比表面积最小(729 m²·g^-1);使用ZnCl₂作为活化剂制备的碳材料(CSi-1.75-Zn)比表面积为1032 m²·g^-1,但其孔体积下降到1.99 cm³·g^-1,且具有最多的吡啶氮和吡咯氮。在以6.0 mol·L^-1 KOH为电解液的三电极体系中,当电流密度为0.5 A·g^-1时,CSi-1.75-Zn的比电容为344 F·g^-1,而CSi-1.75的比电容仅为255 F·g^-1。这表明碳材料的比表面积对超级电容性能影响最大,而孔体积影响较小。电容贡献分析结果表明,相对于CSi-1.75,CSi-1.75-Zn的双电层电容和赝电容都得到了提高,这表明更大的比表面积和更多的吡啶氮和吡咯氮有利于提高碳材料的超级电容性能。     

Preparation and evaluation of carbon coated alumina as a high surface area packing material for high performance liquid chromatography

The retention of polar compounds, the separation of structural isomers and thermal stability make carbonaceous materials very attractive stationary phases for liquid chromatography (LC). Carbon clad zirconia (C/ZrO₂), one of the most interesting, exhibits unparalleled chemical and thermal stability, but its characteristically low surface area (20–30 m²/g) limits broader application as a second dimension separation in two-dimensional liquid chromatography (2DLC) where high retentivity and therefore high stationary phase surface area are required. In this work, we used a high surface area commercial HPLC alumina (153 m²/g) as a support material to develop a carbon phase by chemical vapor deposition (CVD) at elevated temperature using hexane vapor as the carbon source. The loading of carbon was varied by changing the CVD time and temperature, and the carbon coated alumina (C/Al₂O₃) was characterized both physically and chromatographically. The resulting carbon phases behaved as a reversed phase similar to C/ZrO₂. At all carbon loadings, C/Al₂O₃ closely matched the unique chromatographic selectivity of carbon phases, and as expected the retentivity was increased over C/ZrO₂. Excess carbon – the amount equivalent to 5 monolayers – was required to fully cover the oxide support in C/Al₂O₃, but this was less excess than needed with C/ZrO₂. Plate counts were 60,000–76,000/m for 5 μm particles. Spectroscopic studies (XPS and FT-IR) were also conducted; they showed that the two materials were chemically very similar.     

Mn-N-P doped carbon spheres as an efficient oxygen reduction catalyst for high performance Zn-Air batteries

Low-cost and efficient oxygen reduction reaction (ORR) electrocatalysts are the key to developing Zn-air batteries for renewable energy storage. Herein, the Mn-N-P doped carbon sphere was prepared through polymerization of hexachlorotripolyphosphazene (HCCP) and phloroglucinol, and then followed the calcination at 900 °C. Theory calculations demonstrated the introduction of Mn in N-P doped carbon could lower the dissociation barrier of O₂ into O* and promote the ORR through a 4e^? pathway. The as-prepared catalysts exhibited a half-wave potential of 0.82 V vs. RHE and limiting current density of 5.2 mA/cm² toward ORR, which was comparable to those of the commercial Pt/C catalysts. In addition, Zn-air batteries with 0.05 Mn-N-P-C catalysts showed a high specific capacity of 830 mAh/g_Zn and excellent cycle stability. This facile approach demonstrated herein could be a solution to develop optimum non-precious metal catalysts for the application in cathodes of proton exchange membrane fuel cells. This study also provides new insight to design the catalysts of multi-heteroatom coordinated metal in the carbon matrix for both fundamental researches and practical applications.