Synthesis and characterization of Co3O4 nanorods by thermal decomposition of cobalt oxalate

Cobalt oxalate was used as a precursor to prepare Co₃O₄ nanorods by thermal decomposition. The combinations of triphenylphosphine and oleylamine were added as surfactants to control the morphology of the particles. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The diameters of Co₃O₄ nanorods are 20 nm and the average lengths are around 500 nm. The hysteresis loops of the obtained samples reveal the ferromagnetic behaviors, the enhanced coercivity (H_c) and decreased saturation magnetization (M_s) in contrast to their respective bulk materials. The study provides a simple and efficient route to synthesize Co₃O₄ nanorods at low temperature.     

Synthesis and optical properties of flower-like ZnO nanorods by thermal evaporation method

Flower-like ZnO nanorods have been synthesized by heating a mixture of ZnO/graphite powders using the thermal evaporation and vapor transport on Si (1 0 0) substrates without any catalyst. The structures, morphologies and optical properties of the products were characterized in detail by using X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), photoluminescence (PL) and Raman spectroscopy. The synthesized products consisted of large quantities of flower-like ZnO nanostructures in the form of uniform nanorods. The flower-like ZnO nanorods had high purity and well crystallized wurtzite structure, whose high crystalline quality was proved by Raman spectroscopy. The as-synthesized flower-like ZnO nanorods showed a strong ultraviolet emission at 386 nm and a weak and broad yellow-green emission in visible spectrum in its room temperature photoluminescence (PL) spectrum. In addition, the growth mechanism of the flower-like ZnO nanorods was discussed based on the reaction conditions.     

Physico-chemical, optical and electrochemical properties of iron oxide thin films prepared by spray pyrolysis

Iron oxide thin films were prepared by spray pyrolysis technique onto glass substrates from iron chloride solution. They were characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and (UV-vis) spectroscopy. The films deposited at T_s ≤ 450 °C were amorphous; while those produced at T_sub = 500 °C were polycrystalline α-Fe₂O₃ with a preferential orientation along the (1 0 4) direction. By observing scanning electron microscopy (SEM), it was seen that iron oxide films were relatively homogeneous uniform and had a good adherence to the glass substrates. The grain size was found (by RX) between 19 and 25 nm. The composition of these films was examined by X-ray photoelectron spectroscopy and electron probe microanalysis (EPMA). These films exhibited also a transmittance value about 80% in the visible and infrared range. The cyclic voltammetry study showed that the films of Fe₂O₃ deposited on ITO pre-coated glass substrates were capable of charge insertion/extraction when immersed in an electrolyte of propylene carbonate (PC) with 0.5 M LiCLO₄.     

From crystalline V2O5 to nanostructured vanadium oxides using aromatic amines as templates

Nanoneedles, nanorods of B-VO₂, and vanadium oxide nanotubes with high crystallinity were synthesized via a one-step hydrothermal treatment using crystalline V₂O₅ as a precursor and aromatic amines (C₆H₅-(CH₂)_n-NH₂ with n=0, 1, 3) as structure-directing templates. Samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray powder diffraction (XRD), thermal analysis, nitrogen adsorption/desorption isotherms and infrared spectroscopy. Nanoneedles, 0.5-5 μm in length and about 50 nm in average diameter and VO₂(B) nanorods about 20-100 nm wide and up to 2.5 μm long, have been obtained. The inner and the outer diameters of the vanadium oxide nanotubes vary, respectively, between 15-25 and 70-100 nm with a length up to 4 μm.     

Impedance spectroscopy and investigation of conduction mechanism in BaMnO3 nanorods

BaMnO₃ nanorods were synthesized at 200 °C and atmospheric pressure using the composite-hydroxide mediated method. X-ray diffraction, scanning electron microscopy and energy dispersive X-ray spectroscopy were used to investigate the structure, size, morphology, phase purity and elemental composition of BaMnO₃ nanorods. Electrical characterization of BaMnO₃ pellet was performed at 300-400 K and in the frequency range 200 Hz-2 MHz. Temperature dependence of AC conductivity suggests that the BaMnO₃ pellet behaves as a semiconducting material and conduction across the pellet can be explained by the correlated barrier hopping model. Impedance analysis was performed using the equivalent circuit model (R₁Q₁C₁)(R₂C₂) and it suggests a single relaxation process in the BaMnO₃ pellet at a particular temperature. The analysis reveals that the BaMnO₃ pellet behaves like an n-type semiconductor material due to the presence of oxygen vacancies and some disorder. Modulus spectroscopy also supports the impedance results.     

Preparation and luminescent characteristic of Li3NbO4 nanophosphor

Synthesis and luminescence properties of Li₃NbO₄ oxides by the sol-gel process were investigated. The products were characterized by the X-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) spectroscopy and absorption spectra. The PL spectra excited at 247 nm have a broad and strong blue emission band maximum at 376 nm, corresponding to the self-activated luminescence of the niobate octahedra group [NbO₆]⁷⁻. The optical absorption spectra of the samples sintered at temperatures of 600 and 700 °C exhibited the band-gap energies of 4.0 and 4.08 eV.     

Preparation and characterization of SrSnO3 nanorods

Perovskite strontium stannate (SrSnO₃) nanorods were prepared by annealing the precursor SnSr(OH)₆ nanorods at 600 °C for 3 h. The precursor nanorods were hydrothermally synthesized at 160 °C for 16 h using Sr(NO₃)₂ and SnCl₄·5H₂O as starting materials in the presence of surfactant cetyltrimethyl ammonium bromide (CTAB). As-prepared samples were characterized by X-ray diffraction (XRD), thermogravimetric-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and infrared ray spectroscopy (IR). The results show that the as-synthesized powders are made of SrSnO₃ one-dimensional nanorods of about 0.2-1 μm length and 100-150 nm diameter. Possible formation mechanism of SrSnO₃ with nanorod structure under certain conditions was preliminarily analyzed, in which it was thought that CTAB played an important role in the formation process of the nanorod structure. Electrochemical performance of the samples versus Li metal was also evaluated for possible use in lithium-ion batteries.     

Synthesis and characterization of β-Ga2O3 nanorods

A novel method was applied to prepare β-Ga₂O₃ nanorods. In this method, β-Ga₂O₃ nanorods have been successfully synthesized on Si(1 1 1) substrates through annealing sputtered Ga₂O₃/Mo films under flowing ammonia at 950 °C in a quartz tube. The as-synthesized nanorods are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM) and Fourier transform infrared spectroscopy (FTIR). The results show that the nanorod is single-crystalline Ga₂O₃ with monoclinic structure. The β-Ga₂O₃ nanorods are straight and smooth with diameters in the range of 200-300 nm and lengths typically up to several micrometers. The growth process of the β-Ga₂O₃ nanorods is probably dominated by conventional vapor-solid (VS) mechanism.     

Synthesis and photoluminescence of single-crystal GaN nanorods prepared by sol-gel method

A new method was applied to prepare GaN nanorods. In this method, gallium oxide (Ga₂O₃) gel was firstly formed by a sol-gel processing using gallium ethanol, Ga(OC₂H₅)₃, as a new precursor. GaN nanorods were successfully synthesized after annealing of the Ga₂O₃ gel at 1000 °C for 20 min in flowing ammonia. The as-prepared nanorods were confirmed as single crystalline GaN with wurtzite structure by X-ray diffraction (XRD), selected-area electron diffraction (SAED) and high-resolution transmission electron microscopy (HRTEM). Transmission electron microscopy (TEM) displayed that the GaN nanorods were straight and smooth, with diameters ranging from 200 nm to 1.8 μm and lengths typically up to several tens of microns. When excited by 280 nm light at room temperature, the GaN nanorods had a strong ultraviolet luminescence peak located at 369 nm and a blue luminescence peak located at 462 nm, attributed to GaN band-edge emission and the existence of the defects or surface states, respectively.     

Facile synthesis of α-MnO2 nanorods for high-performance alkaline batteries

Single-crystalline α-MnO₂ nanorods have been successfully synthesized by a novel hydrothermal method based on the redox reactions between the permanganate anion MnO₄^- and H₂O in mixture containing KMnO₄ and HNO₃. The products have been characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), transmission electron microscopy (TEM), Fourier transform infrared spectrum (FT-IR) and Brunauer-Emmett-Teller (BET). The results prove that the grain size of α-MnO₂ nanorods with the surface area ∼95.2 m² g⁻¹ is homogeneous with diameters ranging from 10 to 20 nm. The electrochemical property of the material shows that compared with the commercial electrolytic manganese dioxide (EMD), the discharge capacity of the as-prepared α-MnO₂ nanorods is increased by 70.4%, 104.1% and 135.7% at different constant currents of 50, 250 and 500 mA g⁻¹, respectively.     

Femtosecond pulsed laser deposition of nanostructured TiO2 films

Nanostructured deposits of TiO₂ were grown on Si (1 0 0) substrates by laser ablating a TiO₂ sintered target in vacuum or in oxygen using a Ti:sapphire laser delivering 80 fs pulses. The effect of the laser irradiation wavelength on the obtained nanostructures, was investigated using 800, 400 and 266 nm at different substrate temperatures and pressures of oxygen. The composition of the deposits was characterized using X-ray photoelectron spectroscopy (XPS) and the surface morphology was studied by environmental scanning electron microscopy (ESEM) and atomic force microscopy (AFM). Deposits are absent of microscopic droplets in all conditions explored. The best deposits, constituted by nanoparticles of an average diameter of 30 nm with a narrow size distribution, were obtained at the shorter laser wavelength of 266 nm under vacuum at substrate room temperature.     

The synthesis and kinetic growth of anisotropic silver particles loaded on TiO2 surface by photoelectrochemical reduction method

Silver nanorods with average diameters of 120-230 nm and aspect ratio of 1.7-5.0 were deposited on the surface of TiO₂ films by photoelectrochemical reduction of Ag⁺ to Ag under UV light. The composite films prepared on soda-lime glass substrates were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The results show that the TiO₂ film after UV irradiation in AgNO₃ solution is composed of anatase phase TiO₂ and metallic silver with face centered cubic structure. Other compounds cannot be found in the final films. The maximum deposition content of silver particles on the surface of TiO₂ film was obtained with the AgNO₃ concentration of 0.1 M. The kinetic growth rates of silver particles can be controlled by photocatalytic activity of TiO₂ films. The studies suggest that the growth rates of silver particles increase with the enhancement of photocatalytic activity of TiO₂ films. The maximum growth rate of silver particles loaded on TiO₂ films can be up to 0.353 nm min⁻¹ among samples 1#, 2# and 3#, while the corresponding apparent rate constant of TiO₂ is 1.751 × 10⁻³ min⁻¹.     

Growth of nanocrystalline CuIn3Se5 (OVC) thin films by ion exchange reactions at room temperature and their characterization as photo-absorbing layers

Nanocrystalline CuIn₃Se₅ thin films have been grown on ITO glass substrates using chemical ion exchange reactions with CdS, in alkaline medium at pH 11. The as-deposited films were annealed in air at 200 °C for 30 min and characterized using X-ray diffraction (XRD), transmission electron microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy, and scanning electron microscopy to study the structural, compositional and morphological properties. The XRD patterns reveal the nanoparticles size to be of 18-20 nm diameter, while from the SEM images the nanoparticles size is estimated to be 20-30 nm. It is observed that the annealed films contain nanocrystallites connected with each other through grain boundaries, with grain size of about 100-125 nm and have an overall n-type electrical conductivity and higher photoconductivity. The current-voltage (I-V) characteristics (in dark and light) of these films indicated the formation of a Schottky like junction between the n-CuIn₃Se₅ (OVC) and CdS/ITO layers.     

Facile synthesis of Nb2O5 nanorod array films and their electrochemical properties

Nb₂O₅ nanorod array films were synthesized by a facile hydrothermal process using niobium metal foil and NH₄F as precursors. The Nb₂O₅ nanorods stand on the niobium metal foil substrate and are less than 100 nm in diameter and about 1 μm in length. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) characterizations indicate that these nanorods have orthorhombic structure and grew longitudinally along 〈0 0 1〉 direction. The nanorod growth mechanism was discussed. Thermal annealing at a temperature below 500 °C did not change the microstructure of nanorods but improve the crystallinity. The Nb₂O₅ nanorod array films have been tested as cathode material for lithium battery, which showed a good specific capacity up to 380 mAh g⁻¹ even after 50 charge/discharge cycles.     

The effect of different gas atmospheres on luminescent properties of pulsed laser ablated SrAl2O4:Eu,Dy thinfilms

SrAl₂O₄:Eu²⁺,Dy³⁺ thin films were grown on Si (1 0 0) substrates using the pulsed laser deposition (PLD) technique to investigate the effect of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological, photoluminescence (PL) and cathodoluminescence (CL) properties of the films. The films were ablated using a 248 nm KrF excimer laser. Atomic force microscopy (AFM), scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and fluorescence spectrophotometry were used to characterize the thin films. Auger electron spectroscopy (AES) combined with CL spectroscopy were employed for the surface characterization and electron-beam induced degradation of the films. Better PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres with respect to those prepared in vacuum. A stable green emission peak at 515 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions were obtained with less intense peaks at 619 nm, which were attributed to transitions in Eu³⁺. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The CL intensity increased under prolonged electron bombardment during the removal of C due to electron stimulated surface chemical reactions (ESSCRs) on the surface of the SrAl₂O₄:Eu²⁺, Dy³⁺ thin films. The CL stabilized and stayed constant thereafter.     

Evolution of Zn based high purity phases under NH3 gas atmosphere and their PL properties

We report here the evolution of zinc based high purity phases with novel morphologies such as Zn₃N₂ hollow structures, ZnO nanowires and nanopowders, as well as metallic Zn layered hexagonal microparticles at progressively increased reaction temperature of 600 °C, 700 °C, 800 °C under NH₃ gas atmosphere using Zn powder precursor and keeping all other experimental parameters unchanged. Growth mechanism for Zn₃N₂ obtained by nitridation, ZnO by oxidation and Zn microparticles via thermal evaporation & condensation process are discussed briefly. The as-synthesized products were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM). Photoluminescence (PL) studies have revealed very interesting and infrequently observed emission bands at 378 and 661 nm for Zn₃N₂, 359 and 396 nm for ZnO as well as 389 nm for Zn polyhedral microparticles.     

Green synthesis of soya bean sprouts-mediated superparamagnetic Fe3O4 nanoparticles

Superparamagnetic Fe₃O₄ nanoparticles were first synthesized via soya bean sprouts (SBS) templates under ambient temperature and normal atmosphere. The reaction process was simple, eco-friendly, and convenient to handle. The morphology and crystalline phase of the nanoparticles were determined from scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), and X-ray diffraction (XRD) spectra. The effect of SBS template on the formation of Fe₃O₄ nanoparticles was investigated using X-ray photoemission spectroscopy (XPS) and Fourier-transform infrared spectroscopy (FT-IR). The results indicate that spherical Fe₃O₄ nanoparticles with an average diameter of 8 nm simultaneously formed on the epidermal surface and the interior stem wall of SBS. The SBS are responsible for size and morphology control during the whole formation of Fe₃O₄ nanoparticles. In addition, the superconducting quantum interference device (SQUID) results indicate the products are superparamagnetic at room temperature, with blocking temperature (T_B) of 150 K and saturation magnetization of 37.1 emu/g.     

Synthesis of In-doped Ga2O3 zigzag-shaped nanowires and optical properties

In-doped Ga₂O₃ zigzag-shaped nanowires and undoped Ga₂O₃ nanowires have been synthesized on Si substrate by thermal evaporation of mixed powders of Ga, In₂O₃ and graphite at 1000 °C without using any catalyst via a vapor-solid growth mechanism. The morphologies and microstructures of the products were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDS) and photoluminescence spectroscopy (PL). The nanowires range from 100 nm to several hundreds of nanometers in diameter and several tens of micrometers in length. A broad emission band from 400 to 700 nm is obtained in the PL spectrum of these nanowires at room temperature. There are two blue-emission peaks centering at 450 and 500 nm, which originate from the oxygen vacancies, gallium vacancies and gallium-oxygen vacancy pairs.     

Electrochemically deposited photoactive CdIn2Se4 thin films: Structural and optical studies

Electrochemical synthesis of photoactive cadmium-indium-selenide (CdIn₂Se₄) thin films at ambient temperature was reported. The nanocrystalline nature and 1:2:4 elemental chemical stoichiometric ratio for Cd, In and Se were obtained from the X-ray diffraction and energy dispersive X-ray analysis, respectively. Irregular shaped islands of about 400-500 nm in sizes composed of large number of small (∼30-40 nm) spherical grains were confirmed from the atomic force microscopy and the scanning electron microscopy images. The photoelectrochemical measurement of CdIn₂Se₄ film electrode in presence of 1 M polysulphide electrolyte revealed 0.42% photoelectrochemical device conversion efficiency, under the light illumination intensity of 80 mW/cm².     

Low temperature synthesis of iodine-doped TiO2 nanocrystallites with enhanced visible-induced photocatalytic activity

Iodine-doped TiO₂ nanocrystallites (denoted as I-TNCs) were prepared via a newly developed triblock copolymer-mediated sol-gel method at a temperature of 393 K. I-doping, crystallization and the formation of porous structure have been simultaneously achieved. The obtained particles were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, and UV-vis spectrophotometer. The results indicated that the as-prepared I-TNCs possessed a diameter of ca. 5 nm with anatase crystalline structure and a specific surface area of over 200 m² g⁻¹. The presence of iodine expanded the photoresponse in visible light range, and led to enrich in surface hydroxyl group on the TiO₂ surface. Compared with the commercial photocatalyst P25, the I-TNCs significantly enhanced the photocatalytic efficiency in the degradation of rhodamine B and 2,4-dichlorophenol, and the I-TNCs with 2.5 mol% doping ratio exhibited the best photocatalytic activity.