Measurement of lead-210, bismuth-210, and polonium-210 in environmental samples

Mathematical equations governing the ratio of²¹⁰Bi/²¹⁰Pb and²¹⁰Po/²¹⁰Pb activities are used to explain the ingrowth of²¹⁰Bi and²¹⁰Po in environmental samples during post collection. Procedures are described for radiochemical separation of²¹⁰Pb,²¹⁰Bi, and²¹⁰Po in a state of radioactive disequilibrium and quantification by alpha- and beta-counting. Also, the special case is considered where²¹⁰Bi is in equilibrium with²¹⁰Pb, but both are in disequilibrium with²¹⁰Po. In this case, the activities of both²¹⁰Pb and²¹⁰Po are computed by measuring²¹⁰Po activity twice, using alpha-counting.     

210Po、210Bi和210Pb测试技术研究进展与现状

铀系核素210Po、210Bi和210Pb的测试在铀矿地质勘查与核废物安全处置研究、沉积年代学与同位素地球化学研究、大气环境学与辐射卫生学研究等诸多领域具有重要意义。重点总结了近些年来210Pb、210Bi和210Po三核素各种测试技术的研究进展与现状,评述了存在的主要问题及未来发展趋势。     

Presence and forms of210Pb,210Bi and210Po in ground level aerosols

A scheme of fractionation of²¹⁰Pb,²¹⁰Bi,²¹⁰Po forms present in air aerosols based on the combination of methods of radiochemical analysis and radiometric deteemination with leaching by different agents has been developed. The ratio between the²¹⁰Pb,²¹⁰Bi,²¹⁰Po present in the aerosol samples was determined experimentally. Carbonate of²¹⁰Pb, and²¹⁰Po and²¹⁰Bi forms connected with oxides prevai in the aerosol component of atmospheric air.     

Levels of 210Po and 210Pb in cigars

²¹⁰Po and ²¹⁰Pb concentrations have been determined in 58 cigar brands manufactured in 11 countries. Cuban and American cigars showed the lowest ²¹⁰Po content. The mean levels of ²¹⁰Po in Brazilian, European and Dominican cigars were almost identical and somewhat lower than the levels observed for cigars from other Latin American countries. Cuban, American and European cigars contained low levels of ²¹⁰Pb. Cigars from the remaining countries contained twice as much ²¹⁰Pb. The mean ²¹⁰Po/²¹⁰Pb ratio showed an excess of polonium. In the case of a one cigar-a-day smoker, the calculated annual absorbed dose due to ²¹⁰Po is -16 mGy.     

Sequential and rapid determination of Po-210, Bi-210 and Pb-210 in natural waters

A sequential and rapid separation method for the determination of radon daughter nuclides, Pb-210, Bi-210 and Po-210 has been developed for application to natural waters. Rapid separation is attained by the use of the same hydrochloric acid solution. After isolation of the three radionuclides from the sample by co-precipitation with added Fe³⁺, polonium isotopes are first spontaneously deposited onto a silver disc from a 0.5N hydrochloric acid solution. Next, bismuth isotopes are electrodeposited onto a platinum net cathode coupled with a platinum coil anode at 1.2 V. Finally, lead isotopes are electrodeposited onto a platinum net cathode at 1.8 V from the remaining solution by adding hydroxylamine hydrochloride as an anodic depolarizer. This method can be applied to meteorological precipitation samples where these three nuclides are separated within 10 hr after the sampling with chemical yields of more than 80% for Po-210 and Bi-210 and more than 70% for Pb-210. This method is applicable to other environmental water samples.     

Analysis of 210Pb and 210Po in Brazilian foods and diets

Radiochemical procedures for the analysis of ²¹⁰ Pb and ²¹⁰ Po in foods and diets are presented. Because of the low beta energy of ²¹⁰ Pb, its analysis was based on a separation of the daughter radionuclide ²¹⁰ Bi by precipitation of lead sulphate, ²¹⁰ Bi ingrowing and beta counting of this nuclide. ²¹⁰ Po analysis was based on wet dissolution of the sample, deposition onto silver disc and counting by alpha-spectrometry. Levels of these radionuclides in individual items and diets of selected university students were determined in order to evaluate the intakes of ²¹⁰ Pb and ²¹⁰ Po as well as the dose due to ingestion of foods and diets in São Paulo city.     

Determination of210Pb and210Po in human tissues of Japanese

To determine the levels of²¹⁰Pb and²¹⁰Po in human tissues of people in Japan, various tissue samples were obtained at autopsy from the cadavers of 22 oncologic cases, mainly in Niigata Prefecture in northern Japan, from 1986 to 1988.Wet ashing, followed by electrochemical deposition and alpha spectrometry were used to separate and determine the²¹⁰Pb and²¹⁰Po present. Among the tissues analyzed, the highest concentrations of²¹⁰Pb and²¹⁰Po were observed in bone (sternum), liver, and kidneys. The total body burden of²¹⁰Pb and²¹⁰Po was found to be approximately 427 pCi and 514 pCi, respectively. This estimated²¹⁰Po value did not differ significantly from values found in populations in the U.S.A. and European countries.     

Radiochemical determination of210Po and210Pb in water

A method for²¹⁰Po and²¹⁰Pb determination in water samples is described. The nuclides are concentrated, in presence of added²⁰⁸Po and lead carrier, by evaporation. Then the polonium is plated electroless from the acidic solution on a copper planchet and measured by alpha spectrometry.²¹⁰Pb separation from the other isotopes is based on the solutility of PbSO₄ in citrate.²¹⁰Pb content is determined by measuring the activity of its daughter²¹⁰Bi. The critical steps in the isolation of lead have been examined and discussed.     

A simultaneous determination of lead-210 and polonium-210 in sea water

A new radiochemical procedure is described for the determination of lead-210 and polonium-210 in sea water. These nuclides are concentrated by coprecipitation with calcium carbonate from a sea water sample of large volume and then separated from calcium by formation of the hydroxides. Polonium-210 is deposited spontaneously onto a silver disc and determined by an α-counting technique. Lead-210 is also determined by counting the activity of polonium-210 produced during storage for 3 months.     

Measurements of210Pb and210Po in Japanese human hair

²¹⁰Pb and²¹⁰Po in human hair have been measured to serve as an aid in order to estimate the dietary intake and body burden of these radionuclides of Japanese. The²¹⁰Po concentrations found in 83 hair samples were ranging from 4.0 to 59.3 mBq/g with a mean (median) value of 18.2±12.2 (14.9) mBq/g as compared to the²¹⁰Pb concentrations from 0.7 to 6.5 mBq/g with a mean (median) value of 2.3±1.1 (2.0) mBq/g. The²¹⁰Po/²¹⁰Pb activity ratios (mean: 8.7±5.1, median: 7.1) were surprisingly higher compared with the available literature value of about 2. The high concentration of²¹⁰Po in human hair of Japanese may be due to the ingestion of animal protein mainly in the form of seafood.     

Determination of 210Pb, 210Bi and 210Po in natural drinking water

A new method for the radioanalytical determination of the ²²²Rn progenies ²¹⁰Pb, ²¹⁰Bi and ²¹⁰Powill be presented, which has been improved for analyses of water samples fromdifferent regions in Austria. 1–2 liter samples were taken in polyethylenebottles prefilled with conc. HNO₃ to obtain 0.2M acidic solutions,thus avoiding adsorption effects. After adding 1.6 mg of inactive lead carrier,the water sample was evaporated to dryness, converted to the chloride formand dissolved in 1M HCl.     

Determination of 210Pb and 210Po in mineral and biological environmental samples

The paper deals with the determination of ²¹⁰ Pb and ²¹⁰ Po in mineral and biological environmental samples. ²¹⁰ Pb and ²¹⁰ Po were preconcentrated from filtered water samples by coprecipitation with iron(III) hydroxide at pH 9-10 using ammonia solution and the precipitate was dissolved with HCl and mineralized with H2O2. ²¹⁰ Pb and ²¹⁰ Po in soil or sediment, algae and mussel samples were sequentially leached out at 250 °C with HNO₃ +HF, HClO₄ and HCl. About 10-20% of the leaching solution was used for ²¹⁰ Po determination which was carried out at 85-90 °C for 4 hours by suspending a silver disk in a HCl solution of pH 1.5 and containing some hydroxylamine hydrochloride and sodium citrate. No preliminary separation was required and essentially quantitative recoveries were obtained by using standard ²⁰⁹ Po tracer. The remains of the leaching solution were used for the determination of ²¹⁰ Pb which was first separated by a BIO-RAD-AG 1-X4 resin column, then purified by using Na2S to precipitate as PbS and finally precipitated as PbSO₄ for source preparation. Starting from 3 g sediment (30 liter water), the lower limits of detection of the method were 0.73 Bq.kg^-1 (0.078 mBq.l^-1 ) for ²¹⁰ Pb and 0.25 Bq.kg^-1 (0.016 mBq.l^-1 ) for ²¹⁰ Po. The procedure has been checked with two certified samples supplied by the International Atomic Energy Agency (IAEA) and reliable results were obtained. Most of the analyzed samples were sediments, showing average yields of 84.2±5.2% for ²¹⁰ Pb and 96.4±4.1% for ²¹⁰ Po.     

Simultaneous determination of210Bi and210Po on pine needles by solvent extraction and liquid scintillation counting

A determination procedure has been developed for²¹⁰Bi and²¹⁰Po in environmental samples and was applied for pine needles. Bismuth-210 and²¹⁰Po separated from the parent nuclide²¹⁰Pb as BiOCl precipitate were extracted simultaneously by TOPO/toluene containing PPO and POPOP. The separation of²¹⁰Bi and²¹⁰Po from²¹⁰Pb was almost satisfactory. The activity of²¹⁰Bi+²¹⁰Po in the TOPO/toluene was measured periodically by liquid scintillation counting for about 20 days after separation. The time course of the decreasing pattern of the activity was determined by the initial activity ratio²¹⁰Po/²¹⁰Bi. The decreasing pattern of the activity was compared with theoretical patterns, and best estimates for²¹⁰Po and²¹⁰Bi were obtained by non-linear least-squares fitting. The activities of²¹⁰Bi and²¹⁰Po were determined for one-year and two-year old pine needles fro the same pine tree, and weathering half-time and deposition rate of these nuclides was discussed.     

The role of Cherenkov and liquid scintilation counting in evaluating the anion-exchange separation of210Pb−210Bi−210Po

Using as eluent a sequence of 3M HCl, 12M HCl, and 8M HNO₃, a mixture of²¹⁰Pb,²¹⁰Bi, and²¹⁰Po may be clearly separated on a column of Dowex 1×2−100 anion exchange resin. A Cherenkov count in H₂O and the variation in count rate with time confirm that the nuclides emerge in the order²¹⁰Pb→²¹⁰Bi→²¹⁰Po. If 12M HCl is replaced by 1.5M H₂SO₄/2.3 M Na₂SO₄, a clean separation also results, but recovery of²¹⁰Po becomes considerably more difficult. All three nuclides are readily detectable by liquid scintillation counting, with the efficiency for²¹⁰Pb in the 60–70% range. The Cherenkov aqueous counting efficiency for²¹⁰Bi is ∼14–15%.     

Determination of (210)Pb, (210)Bi and (210)Po in natural waters and other materials by electrochemical separation

An improved method for determination of (210)Pb, (210)Bi and (210)Po in both natural waters and solid materials has been developed. Polonium-210 is spontaneously plated onto a silver disc from dilute hydrochloric acid medium. Bismuth-210 is then electro-deposited onto a platinum gauze cathode directly from the same solution, with a graphite rod as anode. Finally, (210)Pb is electro-deposited from a fluoroborate medium onto the same platinum gauze, used as the anode. All three nuclides are subsequently measured by standard low-level alpha and beta counting techniques. The speed of this method (approximately 6 hr per sample after pretreatment) is a distinct advantage over existing techniques, as (210)Bi must be quickly separated from (210)Pb because of its 5.02-day half-life. Another advantage of this method is that the chemical form of the sample solution is suitable for use of established separation schemes for determining other decay-series isotopes (U, Th, Pa, etc.) after the three short-lived nuclides have been processed.     

210Pb and 210Po radionuclides in the urban air of Lodz, Poland

The concentration of two important radionuclides: ²¹⁰Pb and its decay product ²¹⁰Po in the urban air in the center of the Polish city of Lodz were measured during the winter and spring seasons of 2008–2009. Urban airborne particulate matter was collected using two methods: an Anderson 9-stage impactor, and a high-volume aerosol sampler type ASS500 working in the frames of the aerosol sampling network in Poland, established for radionuclide monitoring. Average concentrations for 10 months sampling period for ²¹⁰Pb and ²¹⁰Po were 0.556 and 0.067 mBq/m³, respectively. However remarkable fluctuations due to meteorological condition were observed: from 0.010 to 0.431 mBq/m³ for ²¹⁰Po and from 0.167 to 1.847 mBq/m³ for ²¹⁰Pb. The highest concentrations, almost 60% of the total activities, of both radionuclides were found in the first two fine aerosol fractions with particle diameters below 0.36 μm. The aerosol residence times calculated from the ²¹⁰Po/²¹⁰Pb ratio ranged from 7 to 120 days.     

Polonium-210 and lead-210 in marine organisms: Intake levels for Japanese

The concentrations of²¹⁰Po and²¹⁰Pb were determined in about 30 species of marine organisms collected mainly from the north-easterm region of Japan to know the levels and distributions of these radionuclides and to estimate their intake levels from marine foods.²¹⁰Po and²¹⁰Pb showed a wide range of concentration in species: 0.6–26 and 0.04–0.54 Bq/kg (wet wt) in fishes, 0.5–220 and 0.2–43 Bq/kg (wet wt) in molluscs, echinoderms and chordatas, and 2.8–4.3 and 0.4–1.3 Bq/kg (wet wt) in algae, respectively. Higher accumulation of²¹⁰Po relative to²¹⁰Pb was found in all of the samples analyzed. The intake levels of²¹⁰Po and²¹⁰Pb by marine foods consumption were roughly estimated to be 0.48–0.69 and 0.022–0.042 Bq/d per person, respectively, on the basis of the statistical data on the consumption of seafood and/or production rates of marine foods.     

Transfer of210Pb and210Po to the environment during mining and processing of uranium ores

Transfer of²¹⁰Pb and²¹⁰Po from an uranium mine and mill to the environment was studied by measuring their concentrations in different stages of uranium extraction technology, in waste products from the mill and in environmental waters. A slightly modified radiochemical method was used for²¹⁰Po and²¹⁰Pb determination.     

Separation of the radioelements210Pb−210Bi−210Po by spontaneous deposition onto noble metals and verification by Cherenkov and liquid scintillation counting

A method for the separation of²¹⁰Pb,²¹⁰Bi and²¹⁰Po using spontaneous deposition has been developed. The²¹⁰Bi and²¹⁰Po are simultaneously removed by deposition onto nickel foil (copper and tin could also be used but less effectively) while the²¹⁰Po is separated from²¹⁰Bi, after dissolution of the nickel foil, by deposition onto silver foil. The effectiveness of each separation was evaluated by adding aliquot portions of each solution to a cocktail and counting with a liquid scintillation counter. Water was used as the medium to observe the Cherenkov count of the sample solution.