交联聚苯乙烯单分散微球的制备

微米级粒度均匀的聚合物微球作为功能高分子材料在分析化学、生物化学、标准计量以及某些高新技术领域中应用广泛。制备聚合物微球的传统方法有乳液和悬浮聚合法。乳液聚合只能制备粒径为0．1-0．7μm的颗粒，采用无皂或低皂乳液聚合法制成的单分散聚合物微球粒径接近1μm，但难于达到1μm以上，且后处理比较麻烦；悬浮聚合制备的聚合物微球粒径则一般在100-1000μm之间，且是多分散性的。而分散聚合获得的微球呈单分散性，是制备粒径为1-10μm的单分散聚合物微球的有效方法。     

单分散聚苯乙烯微球的制备及影响因素研究

以聚乙烯吡咯烷酮为分散剂，无水乙醇为反应介质，偶氮二异丁腈为引发剂，采用分散聚合工艺，通过优化反应条件，制备出了粒径为5μm单分散（分散系数≤5％）聚苯乙烯微球。所制备的聚苯乙烯微球标准偏差δ＝0．16μm，分散系数ε＝0．02，且具有良好的球形度，表面非常光滑，无破损，无缺损。对影响单分散聚苯乙烯微球的因素进行了研究，结果表明：随着分散稳定剂用量的增加，聚苯乙烯微球的粒径减小；随着单体和引发剂用量的增加，聚苯乙烯微球的粒径增大。分散稳定剂和单体用量是影响聚苯乙烯微球粒径分布的两个主要因素。     

改进的种子聚合——单分散交联聚苯乙烯微球的合成

 本文结合了种子聚合法和二步溶胀法的特点,提出用改进的种子聚合法以合成粒径大于3微米、粒度呈单分散的交联聚苯乙烯微球。文中采用的粒径为1—2微米的聚苯乙烯胶乳种子是由无皂乳液聚合法制备的。文章研究了溶胀温度、溶胀剂比例、溶胀时间、交联剂、小分子化合物及表面活性剂等因素对生成微球的粒径和分散性的影响。     

室温沉淀聚合制备单分散聚苯乙烯微球

采用沉淀聚合的方法以乙醇/水为混合溶剂、K_2S_2O_8/NaHSO_3为引发剂,室温下引发苯乙烯聚合制备了单分散的聚苯乙烯(PS)微球.研究了反应时间、引发剂用量、反应溶剂中乙醇与水的比例、搅拌速度对聚苯乙烯微球的收率及形貌、单体转化率的影响.结果表明,聚苯乙烯微球的单体转化率、微球的收率和粒径随着反应时间的延长而增加,反应12 h后趋于稳定;当增加引发剂的用量,聚苯乙烯微球的单体转化率、微球的收率和粒径都有所增加,K_2S_2O_8与Na HSO_3用量分别在≤2.0%和1.3%时,能够得到单分散的聚苯乙烯微球;随着反应介质中水含量的增加,聚苯乙烯微球的单体转化率、微球的收率先增加后降低,单分散性变差,水含量在≤40%能够得到单分散的微球;搅拌速度从600 r/min增加到1200 r/min时,微球粒径、收率与单体转化率几乎没有变化.并初步研究了聚苯乙烯微球的形成机理.     

分散聚合法制备单分散交联聚苯乙烯微球

以苯乙烯为单体、二乙烯基苯为交联剂,通过优化反应条件,制备了平均粒径为3.28～9.04 μm的单分散聚苯乙烯微球和平均粒径为6.60 μm的单分散交联聚苯乙烯微球.探讨了单体浓度、引发剂含量、分散稳定剂用量对微球粒径和分散性的影响.热稳定性分析表明:交联聚苯乙烯微球耐热性明显优于线性聚苯乙烯.     

不同尺寸（0.02—0.5μm）单分散聚苯乙烯乳液微球的制备

通过对苯乙烯乳液聚合微观动力学以及聚合过程中胶粒直径及其分布随时间变化的理论分析,并通过实验验证,比较了不同乳化剂种类、不同反应温度和不同单体用量条件下,产物胶乳的粒径分布,发现乳液聚合最终产物的粒径分布与成核期长短没有直接联系,而是取决于自由基进入胶粒的速率常数、稳态增长时间、胶粒中的平均自由基数目和胶粒的体积增长速率,胶乳单分散性随这些参量的增大而提高,从而解释了采用高温、高引发剂浓度以及长时间反应的条件对最终的胶粒尺寸分布的影响。本文还通过实验,找到了在20～500nm范围内控制粒径大小及粒径分布的方法。在20～100nm的范围内,用一步法乳液聚合,通过改变单体用量和乳化剂浓度,制备了一系列粒径的单分散聚苯乙烯胶乳;在100～500nm的范围内,运用种子乳液聚合,通过改变溶胀单体与种子胶乳的用量比,也制得了不同粒径的单分散聚苯乙烯胶乳。     

分散聚合法制备单分散聚苯乙烯微球

以苯乙烯为单体,偶氮二异丁腈为引发剂,聚乙烯吡咯烷酮为分散稳定剂,在乙醇/水的极性反应体系中,使用分散聚合法制备了聚苯乙烯(PS)微球。研究了制备工艺对微球分子量等远程结构参数的影响。研究结果表明:在适合微球形成的单体用量、引发剂和分散稳定剂的浓度、反应温度、时间和乙醇/水的比例等参数下,克服了以往存在的粒径不均匀、分子量较低、微球表面圆整光洁度较低和产率偏低等主要问题,制备了粒径在1.5~3μm之间、粒径分布1.05~1.08、分子量80×104左右、最高得率达97%、球体表面光洁、球形对称均匀且相互不粘连的单分散PS微球。     

改进的种子聚合——单分散交联聚苯乙烯微球的合成

本文结合了种子聚合法和二步溶胀法的特点,提出用改进的种子聚合法以合成粒径大于3微米、粒度呈单分散的交联聚苯乙烯微球。文中采用的粒径为1—2微米的聚苯乙烯胶乳种子是由无皂乳液聚合法制备的。文章研究了溶胀温度、溶胀剂比例、溶胀时间、交联剂、小分子化合物及表面活性剂等因素对生成微球的粒径和分散性的影响。     

分散聚合制备羧基化单分散聚苯乙烯交联微球

以苯乙烯(St)、丙烯酸(AA)为单体,二乙烯基苯(DVB)为交联剂,偶氮二异丁腈(AIBN)为引发剂,采用分散聚合和交联剂后滴加法合成了单分散羧基化交联聚苯乙烯微球。通过傅立叶红外光谱(FT-TR),扫描电子显微镜(SEM),激光粒度及Zeta电位分析仪等对微球结构进行了表征。结果表明,引发剂、分散剂用量和交联剂的加入方式对微球粒径及单分散性影响显著,当St用量为15%(wt)、DVB用量为1%(wt)、AA用量为1%(wt)、AIBN用量为2%(wt)、PVP用量为6%(wt)时所制备的微球具有良好的单分散性和球形形貌,粒径达到4μm,且微球表面带负电荷。     

分散聚合与水热处理相结合制备单分散聚苯乙烯微球的研究

将分散聚合与水热处理相结合,以聚乙烯醇为稳定剂,以乙醇和水为分散介质,三羟甲基丙烷三丙烯酸酯为交联剂,一步法成功制备得到不同粒径的单分散交联聚苯乙烯微球.以乙醇/水的比例为50/50的反应体系为基础,研究了聚乙烯醇类型和含量,有机相含量,引发剂浓度,以及水热釜填充量等对所制备的微球形貌的影响,发现聚乙烯醇类稳定剂的分子量的降低和含量的增多倾向于生成黏连的微球;在有交联剂的条件下,不含稳定剂的体系仍能够得到单分散的交联PS微球;有机相含量的增加会导致微球呈现多分散性;而体系中引发剂的含量和反应液在水热釜中的填充量对微球的形貌影响不大.进一步针对水热法的特点分析探讨了一步法成功制备单分散的交联聚苯乙烯微球的原因及其机理.     

光致变色多孔聚苯乙烯功能微球的制备和性能

以甲苯/庚烷为致孔剂,利用分散聚合技术制备了多孔交联聚苯乙烯微球.研究了聚合单体、引发剂、稳定剂、交联剂等对微球平均粒径的影响,并初步评价了其在常温常压下吸附光致变色材料后的光致变色性能.结果表明,在最佳条件下制得的多孔聚合物微球平均粒径为1 μm;吸附光致变色材料后,其在紫外或日光照射下具有快速可逆的光致变色功能.利...     

分散聚合法制备液相芯片聚苯乙烯磁性复合微球的研究

本文将丙烯酸基磁流体均匀分散到苯乙烯单体中,采用分散聚合法制备出了适于构建液相芯片微球载体的单分散性微米级磁性微球.考察了丙烯酸基磁流体预处理时间、加料顺序和单体量对微球形貌和粒径分布的影响及其条件优化.扫描电镜(SEM)显示磁性微球平均粒径为7.77 μm,具有良好的单分散性(多分散指数PDI为1.03),并且表面光滑致密;用超导量子干涉磁强计测量了Fe3O4纳米粒子的磁化曲线;用红外光谱(FT-IR)和热失重(TG)方法表征了磁性微球的化学结构及Fe3O4含量.     

Study of a shear thickening fluid: the suspensions of monodisperse polystyrene microspheres in polyethylene glycol

The monodisperse polystyrene (PS) microspheres were prepared by dispersion polymerization. The rheological properties of shear thickening fluid (STF) based on PS microspheres dispersing in polyethylene glycol with different concentrations were studied through the steady and oscillatory shear at different temperatures, respectively. All suspensions successively present the first shear thinning, the shear thickening, and the second shear thinning. The experimental results indicate that the shear thickening behavior of STF is controlled by the concentration of PS microspheres and temperature, as changed from continuous shear thickening (CST) to discontinuous shear thickening (DST) with increasing solid content or decreasing temperature. The STF is affected by shear rate, temperature, and the viscosity of the dispersed medium, and it is reversible absolutely and presents transient response ability. Both CST and DST behave as dilatancy. The PS microsphere aggregations formed under shear stress may result in the shear thickening in STFs.     

Morphological investigations of crosslinked polystyrene microspheres by seeded polymerization

 Crosslinked polystyrene microspheres with novel surface and inner morphologies were synthesized by seeded polymerization following a seed-swelling method, using uncrosslinked polystyrene microspheres as seeds and a mixture of toluene, styrene (St), and divinylbenzene (DVB) as the swelling agent. With the increasing toluene/ (St+DVB) ratio, the crosslinked particles changed from smooth-surfaced spheres to deformed spheres with dimples or heavy dents at the surface. A single hole inside the spherical particles was produced at low St/DVB ratio, while higher St/DVB ratios gave irregular dented or dimpled particles. Ultrathin cross-section observation by TEM revealed a non-uniformly crosslinked inner structure. Received: 20 January 1998 Accepted: 14 April 1998     

Graft copolymers having hydrophobic backbone and hydrophilic branches. XI. Preparation and thermosensitive properties of polystyrene microspheres having poly (N-isopropylacrylamide) branches on their surfaces

Thermosensitive microspheres with 0.4–1.2 μm diameter consisting of a polystyrene core and poly(N-isopropylacrylamide) (polyNIPAAm) branches on their surfaces were prepared by the free radical polymerization of a polyNIPAAm macromonomer and styrene in ethanol. Electron spectroscopy for chemical analysis (ESCA) of the microsphere surface suggested that polyNIPAAm chains were favorably located on the surface of the microspheres. The morphology of the microspheres was observed by transmission electron micrograph (TEM) and the particle size of was estimated by submicron particle analyzer. The molecular weight of the polyNIPAAm macromonomer, the ratio of the macromonomer and styrene, and the polymerization temperature affected the particle size. Thermosensitive properties of polyNIPAAm-coated polystyrene microspheres were evaluated by the turbidity of their dispersion solutions and the hydrodynamic size of the miocrospheres. The transmittance in dispersion solutions changed clearly, similar to oligoNIPAAm and polyNIPAAm macromonomers. In addition, the particle size of microspheres decreased with rising temperature. These results were explained by the thermosensitivity of polyNIPAAm branches on the microsphere surface. © 1996 John Wiley & Sons, Inc.     

一步聚合法制备壳核型、可控阶层结构的羰基铁/聚苯乙烯复合微球

采用改进的悬浮聚合法合成了一系列粒径和结构可调的羰基铁粉/聚苯乙烯磁性高分子微球.利用傅立叶变换红外光谱仪、热重分析仪、X射线衍射仪、扫描电镜等分析了微球的结构、化学成分及形貌.结果表明,通过改变苯乙烯单体和聚乙烯醇(PVA)的加入量,可以制备三类不同形貌和结构的复合微球,即多孔复合微球,无孔复合微球和含"带状"突起的...     

Adsorption of monoclonal IgG on polystyrene microspheres

In this paper the adsorption of a monoclonal antibody IgG-1 isotype against HBsAg onto positively and negatively charged polystyrene beads has been studied. To determine the role played by electrostatic forces in the adsorption process different pH values were used. It was confirmed that the affinity of adsorption isotherms depends on the electrostatic interaction between protein and polymer surface. The maximum adsorption amount is located around the i.e.p. of the dissolved protein, and decreases markedly as pH moves away. Thus, the major driving force for adsorption of monoclonal antibodies on polystyrene beads comes from the hydrophobic interaction between the antibody molecules and the adsorbent surface. Desorption of preadsorbed IgG molecules by increasing ionic strength has shown that the positively charged polystyrene is also more hydrophobic in character than the negatively charged one. Finally, electrokinetic experiments have determined that the electric double layer (e.d.l.) of monoclonal antibody changes as the consequence of adsorbing on charged polymer surfaces.     

基于聚苯乙烯微球放大的凝血酶化学发光检测新技术

本文以羧基96孔板为分离载体,核酸适配体作为分子特异性识别元件,聚苯乙烯微球作为放大载体,辣根过氧化物酶为标记物,构建了化学发光（CL）高灵敏度凝血酶检测新技术.实验结果表明：该放大技术不但灵敏度高,且抗干扰能力强,其他蛋白质如IgG、IgM、IgA、IgE、IFN均无明显干扰.聚苯乙烯微球放大体系中凝血酶的线性范围为7.8～250pmol/L,最低检测浓度可达3.9pmol/L;而不放大检测技术的线性范围为0.94～30nmol/L,最低检测浓度为0.46nmol/L,放大体系将检测灵敏度提高100多倍.综合而言,基于适配体识别和聚苯乙烯微球放大的凝血酶CL检测新技术具有通量大、简单快速和灵敏度高的特点,有望在凝血酶高通量检测领域获得应用.     

Flow of monodisperse polystyrene solutions through porous media

In this work, we study the origin of the extension thickening commonly observed when solutions of flexible polymers flow through porous media and ideal elongational flows. We have used randomly packed beds of glass beads as porous media. We have performed experiments with closely monodisperse atactic polystyrene of different molecular weights dissolved in organic solvents. The use of a closely monodisperse polymer allowed us to make a more meaningful comparison between the results obtained using opposed jets and porous media flow, as compared to previous works on polydisperse polymers. The results indicate that the coil-stretch transition of isolated polymer molecules in solution cannot be the only mechanism responsible for the extension thickening. It is clear that part of the observed effect is due to the extension of isolated molecules, but the main factor causing a great increase in the elongation viscosity beyond a critical strain rate is the formation of transient entanglement networks.     

Facile and controllable assembly of multiwalled carbon nanotubes on polystyrene microspheres

Herein a facile and controllable heterocoagulation between polystyrene （PS） microspheres and multiwalled carbon nanotubes （MWCNTs） is introduced based on colloid thermodynamics. The MWCNTs play the role of steric stabilizer for stabilizing the metastable PS microspheres and thus immobilize spontaneously on the surface of PS microspheres. The synthesized MWCNTs-coated PS composite particles have been extensively characterized by scanning electron microscopy, transmission electron microscopy, thermogravimetry and Raman spectroscopy. The results indicate that the structure and morphology of the resultant MWCNTs-coated PS composite particles are significantly affected by the weight ratio of PS and MWNCTs and the amount of poly（vinylpyrrolidone） that is injected into PS dispersion before they are mixed with MWCNTs. Therefore, these composite particles have the potential to produce MWCNTs-based composite materials with controllable mass loading and dispersity of MWCNTs.