新建高焓激波风洞Ma=8飞行模拟条件的实现与超燃实验

针对高Mach数超燃冲压发动机实验能力空缺问题,基于航天十一院新建的FD-21高能脉冲风洞,进行了Ma=8超燃飞行条件的模拟能力设计与调试,获得了总焓2.9 MJ/kg、总压11.01 MPa实验条件,实现了Ma=8、高度31 km飞行条件的风洞模拟.在此基础上,研发了匹配的氢燃料供应及喷注时序控制系统,设计了超燃冲压发动机模型,开展了超燃冲压发动机模型自由射流应用性风洞实验,获得了氢气燃料与空气、氮气超声速气流耦合流动作用下的实验模型壁面压力数据.在当量比近似一致条件下,空气来流对应的燃烧室壁面压力明显高于氮气来流情况,表明氢气在1 ms有效实验时间内完成了与超声速空气来流的混合、点火与燃烧,获得燃烧释热特性,确认了在FD-21高能脉冲风洞开展高Mach数超燃实验是切实可行的,为后续研究奠定了良好的基础.      

高压环境下1.58μm波段CO2吸收光谱特性分析

高压气体吸收光谱特性的研究是可调谐半导体激光吸收光谱技术应用于爆轰发动机等高压燃烧环境的重要基础.为了解气体吸收光谱随压力的变化规律特别是在高压下的吸收光谱特性,本文以CO₂为气体介质对其在高压环境下近红外波段1.58μm处的吸收光谱进行了理论分析与试验研究,并给出一种高压气体浓度的计算方法.在1—10.13×10⁵Pa压力环境下,对1.58μm处CO₂吸收光谱进行了数值模拟,搭建了高压环境气体在线测量试验系统,对CO₂在波段1578.1—1579.7 nm的吸收光谱进行了试验测量.利用线性回归拟合将试验所得光谱吸收率与模拟吸收率进行对比,对高压环境下气体浓度进行了计算.结果表明,试验所得吸收光谱与数值模拟结果相吻合,1—10.13×10⁵Pa压力环境下利用线性拟合寻优法计算气体浓度最大误差为5.5%,平均误差2.6%.     

三角翼标模摩擦阻力测量的高超声速风洞实验与数据确认

描述了剪切敏感液晶涂层（shear-sensitive liquid crystal coatings,SSLCCs）在高超声速风洞中针对三角翼标模进行表面摩擦阻力（简称摩阻）测量的应用情况.建立了基于剪切敏感液晶涂层光学测量系统,在中国航天空气动力技术研究院FD-07风洞中进行了三角翼摩阻测量实验,给出了三角翼表面摩阻分布数据,表明流场结构的复杂.实验结果证明了此方法进行高超声速摩阻测量的可行性,有效解决了在高超声速流场条件下表面摩阻预测的难题,具有重要的应用价值.      

JF12激波风洞高Mach数超燃冲压发动机实验研究

针对高Mach数（Ma ≥ 7）超燃冲压发动机高气动阻力下的燃烧组织问题,提出一种双突扩燃烧室结构方案.使用数值模拟方法考察了射流与双突扩燃烧室组合方式的混合燃烧特性.设计了双突扩超燃冲压发动机模型,在力学研究所JF12长试验时间激波风洞内,开展了Ma=7.0和Ma=9.5的氢燃料点火和燃烧试验对比.在风洞有效试验时间100 ms内,实现了Ma=7.0和Ma=9.5超燃冲压发动机的成功点火与稳定燃烧.在Ma=7.0情况下,进气道采用三维压缩,燃烧室入口设计Mach数Ma_c=2.5,壁面压力分布实验结果显示燃烧放热靠近燃烧室扩张段上游;在Ma=9.5情况下,进气道采用二维压缩,燃烧室入口设计Mach数Ma_c=3.5,由于燃烧室流动速度特别高,燃烧放热靠近燃烧室扩张段下游.      

采用极限学习机的流场积分吸光度快速测量方法

发动机是飞行器动力系统的核心组件,发动机流场的动态监测可以掌握发动机内部流场的燃烧情况,对于飞行器状态监测和性能评估具有重要意义.拥有先进的诊断技术是发展发动机技术的基础,也是研制新型航空航天飞行器的必要条件之一.激光吸收光谱技术可以实现燃烧场气体参数的测量,在发动机严苛的流场环境中,吸收光谱波长调制技术(WMS)可以...     

光学诊断专题序言

光学诊断技术主要是以激光技术、光谱技术、光电探测技术、数据图像处理技术等为基础的一种综合性测试诊断技术可以实现复杂流场温度、组分浓度、速度、流场结构等参量信息的高时空分辨精确测量而且对测量流场无扰动.近年来光学诊断技术已开始从实验室基础研究走向于各类风洞、发动机等重要设备的工程应用这对于深入研究高超声速流动和燃烧化学反应动力学过程如高焓非平衡流动、高超声速边界层转捩、超声速燃烧动力学、汽车/飞机/火箭/卫星等发动机燃烧不稳定性和污染控制等具有重要意义.     

TDLAS与CARS共线测量发动机温度

发动机燃烧室设计以及计算流体动力学模型的建立和验证需要对燃烧室流场温度等参数进行精细化测量。本文提供了一种TDLAS与CARS技术共线的测温装置,解决了两种技术在联合测量时探测区域不一致的问题,同时使二者共用发射端与接收端,降低了系统的复杂性。利用建立的测量系统在超燃发动机试验台不同位置处开展了温度测量实验,结果表明发动机燃烧段的凹槽区域内(距流道下壁面30mm)煤油燃烧时期温度最高(约2400 K),而发动机燃烧段下沿(距流道下壁面10 mm)煤油燃烧时期温度上升不明显。     

自由活塞激波风洞压缩管非等熵流动分析

在自由活塞驱动的高超声速地面试验设备中,自由活塞压缩器的运行状态对于试验气流状态参数、试验时间及设备安全性起到决定性的作用.研究基于FD-21自由活塞激波风洞结构参数,针对典型的活塞压缩器运行状态展开数值模拟和等熵理论预测,分析压缩管中的波系结构和非等熵效应引起的流动参数变化.进一步地,将压缩管中的总熵变来源分解为激波和黏性两部分;改变驱动压力、活塞质量、压缩管初始压力和压缩管长度进行数值模拟,分析熵变变化规律,并进行参数影响的归一化分析,结果表明归一化后的熵变仅与压缩比有关;最后,对等熵理论进行修正,修正后的压缩管压力与实验和数值结果更为吻合.      

高速流场对光传输特性的影响

利用一座小型跨超声速风洞进行了高速流场光传输特性试验研究。光束在高速流场中传输时,由于流场密度变化,光波波前会发生畸变。利用风洞提供0.7,2.0和3.0等气流马赫数的流场条件,采用基于夏克-哈特曼波前传感器的光学测量系统,对光束在风洞流场中传输时的波前畸变进行了测量。试验结果表明:随着风洞流场马赫数增加,流场对光波传播的影响增大,光波波前畸变量显著提高。因此,在利用风洞进行气动光学试验研究之前,有必要消除风洞流场本身对光波传输的严重干扰。     

固体火箭发动机羽流流速TDLAS测量方法研究

针对现有对固体火箭发动机推进剂燃烧时产生的羽流流速测量方法的不足，提出了将可调谐半导体激光吸收光谱（TDLAS）技术应用于羽流流速的测量方法，通过测量燃烧产物中H₂O分子位于1 392 nm处的单根吸收谱线特征，根据多普勒效应建立的光谱频移和分子速度之间的关系来获得气流流速，解决了接触式测量方法会干扰羽流场和传统非接触式测量中示踪粒子不均匀的问题，并且取得了有效试验数据，通过对试验数据进行分析处理，得到了发动机的羽流流速。     

Numerical flow visualization of a Single Expansion Ramp Nozzle with hypersonic external flow

Numerical simulation of scramjet asymmetric nozzle flow is carried out to visualize and investigate the effects of interaction between engine exhaust and hypersonic external flow. The Single Expansion Ramp Nozzle (SERN) configuration studied here consists of flat ramp and a cowl with different combinations of ramp angle and cowl geometry. UsingPARAS 3D, simulations are performed for a free stream Mach number of 6.5 that constitutes the external flow around the vehicle. Appropriate specific heats ratio has been simulated for the jet and free stream flow. External shock wave due to jet plume interaction with free stream flow, the internal barrel shock wave and the shear layer emanating from the cowl trailing edge and sidewalls are well captured. Wall static pressure distribution on the nozzle ramp for different nozzle expansion angles has been computed for both with and without side fence. Axial thrust and normal force have been evaluated by integrating the wall static pressure. Effect of cowl length variation and side fence on the SERN performance has also been studied and found to be quite significant. Based on this study, an optimum ramp angle at which the SERN generates maximum axial thrust is obtained. SERN angle of 20° was found to be optimum when the flight axis coincides with nozzle axis.     

Dual/scram-mode combustion limits of ethylene and surrogate endothermically-cracked hydrocarbon fuels at Mach 8 equivalent high-enthalpy conditions

This paper examines the scram/dual-mode combustion limits of hydrocabon fuels within a Mach 8, scramjet combustor. Flight-equivalent flows were delivered to the axisymmetric, cavity combustor via a reflected shock tunnel. Two scramjet fuels were examined: ethylene and a surrogate mixture representing endothermically cracked n-dodecane. Combustion modes were examined via static pressure sensors and through both chemiluminescence imaging, and planar laser induced fluorescence (PLIF) of the OH combustion radical in the combustor exhaust plume. Ethylene-fuelled experiments developed scram-mode combustion under reduced fuelling conditions, experiencing shock wave dominated flowfields. OH PLIF diagnostics indicated such combustion modes developed a ring-like structure of combustion products, primarily axisymmetrically adjacent to the combustor wall. Increased fuelling anchored combustion downstream of the fuel injector, while further increases instigated dual-mode combustion. In this mode, subsonic combustion regions combine with the supersonic coreflow to permit the transfer of information upstream with substantially increased pressure encountered. Optical diagnostics indicate broadly asymmetric, unsteady combustion features. The surrogate mixture representing endothermically cracked n-dodecane experienced rapid onset from no-combustion (optically confirmed) to fully developed dual-mode combustion at critical fuelling rates. OH PLIF signals and chemiluminescence of this fuel were weaker than comparable ethylene cases, indicating potential differences in combustion pathways.     

进口条件对超燃冲压发动机氢气燃烧流场特性的影响分析

对不同进口条件下的超燃冲压发动机燃烧室内氢气喷流超声速燃烧流动特性进行了数值模拟与分析.宽范围超燃冲压发动机是吸气式高超声速飞行器推进系统设计中的热点问题之一,受实验设备硬件条件及实验技术限制,数值模拟技术仍然是超燃冲压发动机燃烧室内燃气燃烧特性及流场特性的主要研究手段.采用基于混合网格技术的多组元N-S方程有限体积方法求解器,在不同进口Mach数及压强条件下,对带楔板/凹腔结构的燃烧室模型氢气喷流燃烧流场进行了数值模拟,对比分析了氢气喷流穿透深度、喷口前后回流区结构、掺混效率及燃烧效率等流场结构与典型流场参数的变化特性及影响规律.研究成果可为宽范围超燃冲压发动机喷流燃烧流动特性分析提供参考.      

入射激波诱导环氧丙烷爆炸特征研究

用自行设计激波管点火测试技术,实验研究了温度范围760-1380K间入射激波诱导下环氧丙烷的点火机理。利用激波管压力传感器测定了H*(486.1) 和O (470.5nm)随激波诱导强度变化的点火时间特征。实验结果表明：在低马赫数下氢氧自由基出现时间较接近,1.5-2.5马赫间随激波诱导强度增大而线性减小;而马赫大于2.5后,氧自由基的出现时间迅速减小,是由于高活化能的氧自由基的点火时间对强激波较敏感,而诱导强度大于3.5马赫后对两者点火影响区别就下明显了。实验数据将有益于含能材料点火时间的研究。     

入射激波诱导环氧丙烷爆炸特征研究

用自行设计激波管点火测试技术,实验研究了温度范围760-1380K间入射激波诱导下环氧丙烷的点火机理。利用激波管压力传感器测定了H*(486.1) 和O (470.5nm)随激波诱导强度变化的点火时间特征。实验结果表明：在低马赫数下氢氧自由基出现时间较接近,1.5-2.5马赫间随激波诱导强度增大而线性减小;而马赫大于2.5后,氧自由基的出现时间迅速减小,是由于高活化能的氧自由基的点火时间对强激波较敏感,而诱导强度大于3.5马赫后对两者点火影响区别就下明显了。实验数据将有益于含能材料点火时间的研究。     

Combustion characteristics of a dual-mode scramjet combustor with cavity flameholder

Combustion characteristics of a laboratory dual-mode ramjet/scramjet combustor were studied experimentally. The combustor consists of a sonic fuel jet injected into a supersonic crossflow upstream of a wall cavity pilot flame. These fundamental components are contained in many dual-mode combustor designs. Experiments were performed with an isolator entrance Mach number of 2.2. Air stagnation temperatures were varied from 1040 to 1490 K, which correspond to flight Mach numbers of 4.3–5.4. Both pure hydrogen and a mixture of hydrogen and ethylene fuels were used. High speed imaging of the flame luminosity was performed along with measurements of the isolator and combustor wall pressures. For ramjet mode operation, two distinct combustion stabilization locations were found for fuel injection a sufficient distance upstream of the cavity. At low T₀, the combustion was anchored at the leading edge of the cavity by heat release in the cavity shear layer. At high T₀, the combustion was stabilized a short distance downstream of the fuel injection jet in the jet-wake. For an intermediate range of T₀, the reaction zone oscillated between the jet-wake and cavity stabilization locations. Wall pressure measurements showed that cavity stabilized combustion was the steadiest, followed by jet-wake stabilized, and the oscillatory case. For fuel injection close to the cavity, a hybrid stabilization mode was found in which the reaction zone locations for the two stabilization modes overlapped. For this hybrid stabilization, cavity fueling rate was an important factor in the steadiness of the flow field. Scramjet mode combustion was found to only exist in the cavity stabilized location for the conditions studied.     

Flame dynamics under various backpressures in a model scramjet with and without a cavity flameholder

Flame dynamics under various backpressure conditions were experimentally investigated using direct flame visualization, high-speed CH* chemiluminescence imaging, and wall pressure measurements. The stagnation pressure and temperature used in the present study were 100 kPa and 2500 K, respectively, with a freestream Mach number of 4.5. Rectangular scramjet models with and without a cavity were used to explore the effects of the cavity on flame dynamics when operating in scramjet mode, ramjet mode, and unstart. The flow rate of the ethylene jet was varied to impose backpressures corresponding to each operation mode. For both models, reverse flame propagation was observed for ramjet mode and unstart. For ramjet mode, flame fluctuation occurred within the isolator due to the coupling of fluid dynamics and combustion. The presence of a cavity enhanced combustion and reduced flame fluctuation in both scram and ramjet mode. The cavity promoted unstart because of the greater heat release from combustion. Further research using spatially resolved diagnostic techniques is needed to identify the flame locations for ramjet mode and unstart.     

激波沿H2／空气界面绕圆、方柱强化混合的数值研究

用迎风TVD格式求解二维、层流全N－S方程,对激波沿H2和空气界面绕圆、方柱流动及其诱导的剪切混合进行了数值模拟,得到了流场的压力和组分密度分布,计算结果表明：激波在H2传播得快,剪切层中出现吸涡和调节激波,卷吸涡与柱体撞击后,反射出一道激波,H2沿柱体表面向下游扩散,H2／空气接触面与柱体分离后,形状畸变并产生新的卷吸涡。H2分布表明：在办面上加圆柱或方柱,可有效地强化燃料混合,方柱的增强效果更明显此,在圆柱表面,H2、空气中激波均发生由RR向MR的转变,两Mach杆在下游相互透射,对于方柱,H2中激波中激波沿下表面传播几乎不受影响,空气中激波沿上表面发生Mach反射,其Mach杆和H2中绕射激波相互透射,柱体左侧最终形成一脱体激波,流场存在激波、卷吸涡、接触面向的相互作用,但波系结构相似。