纳米多孔双金属氧化物NiCo2O4的制备及其电化学性能

采用快速凝固与脱合金化相结合的方法制备纳米多孔Ni、Ni-Co合金,分别经腐蚀与退火获得纳米多孔NiO、NiCo_2O_4,采用XRD、SEM、TEM、N_2吸附-脱附等对多孔NiO、NiCo_2O_4电极的物相、形貌结构、孔径分布进行表征,并通过循环伏安、恒电流充放电等方法测试多孔电极的电化学性能。结果表明,得到的纳米多孔NiO具有均匀的"泥裂"式结构,在1A·g~(-1)电流密度下比电容为375 F·g~(-1),当电流密度增加至20 A·g~(-1)时的比容保持率为67.5%,在4 A·g~(-1)电流密度下循环充放电1 000次,比容保持率为81.7%;NiCo_2O_4形成典型的开放式纳米多孔双连续结构,其在1A·g~(-1)电流密度下比电容为674 F·g~(-1),当电流密度增加至20 A·g~(-1),比容保持率达72.0%;在4 A·g~(-1)电流密度下循环充放电1 000次,比容保持率达92.9%,双连续纳米多孔结构及其提供的机械稳定性,使得NiCo_2O_4表现出更为优异的超电容性能。     

超级电容器用相互连接的类石墨烯纳米片

采用氧化镁模板耦合原位氢氧化钾活化法制备了超级电容器用煤焦油基相互连接的类石墨烯纳米片(IGNSs)。所制备的IGNS具有高达2887 m~2·g~(-1)的比表面积和大量的分级短孔。当作为超级电容器的电极材料时,在6 mol·L~(-1) KOH电解液中,于0.05 A·g~(-1)的电流密度下,IGNS显示出313 F·g~(-1)的高比容;在20 A·g~(-1)的电流密度下,IGNS的比电容为261F·g~(-1),显示了好的倍率性能;经过10000次循环测试后,其容量保持率为92.7%,展现了优异的循环稳定性。这一工作为从芳烃分子大规模生产高性能储能用类石墨烯纳米片提供了一种简单的方法。     

香菇生物质基氮掺杂微孔碳材料的制备及其在超级电容器中的应用

采用简易浸泡法和一步碳化/活化法制备香菇生物质基氮掺杂微孔碳材料(NMCs),利用扫描电子显微镜(SEM)、透射电子显微镜(SEM)、X射线衍射(XRD)和X射线光电子能谱(XPS)对材料的结构形貌进行表征,并研究了其超级电容特性。测试结果表明,NMCs的微孔比表面积高达1 594 m~2·g~(-1),且拥有更高数量的含氮官能团,其吡啶型含氮官能团比例也有所提高,展现出优异的超级电容特性。在0.5 A·g~(-1)的电流密度下,其比容量高达325 F·g~(-1),当电流密度上升到20 A·g~(-1)时,其比电容仍然高达180 F·g~(-1),表现出优异的倍率性能;同时,在5 A·g~(-1)的电流密度下,电极经历5 000次充放电循环后具有97.7%的比容量保持率,展现出优异的循环稳定性。这主要归因于NMCs超高的微孔比表面积和丰富的含氮官能团。     

MnO_2纳米粒子的制备及其超电容性质研究

本文采用化学共沉淀法制备了MnO_2。通过XRD、BET、SEM、TEM及HRTEM等表征手段研究MnO_2的形貌及结构,结果显示制备的MnO_2由纳米粒子组成,且具有较大的比表面积(124.7 m~2·g~(-1))。将制得的MnO_2应用于超级电容器时,电化学测试结果表明,在电流密度为0.3 A·g~(-1)时,MnO_2的比电容达到194.7 F·g-1,同时有着优秀的倍率特性。循环稳定性测试表明MnO_2在电流密度2 A·g~(-1)的条件下,恒流充放电(GCD)1000次后的电容保持率达到102.7%,显示了MnO_2具有优异的电化学性能。     

离子液体辅助条件下由稻壳合成超级电容器用多孔炭（英文）

本文以稻壳为碳源,以离子液体1-丁基-3-甲基咪唑六氟磷酸盐(BMIMPF_6)为模板和辅助活化剂制备了多孔炭材料(PCs).多孔炭的比表面积达1438 m~2·g~(-1),总孔容达0.75 cm~3·g~(-1).以PCs为超级电容器电极材料,6 mol·L~(-1)的KOH溶液为电解液组装成扣式电池,在0.05 A·g~(-1)的电流密度下,比电容高达256 F·g~(-1);当电流密度增大至10A·g~(-1),其比电容仍保持在211 F·g~(-1),展现出好的倍率性能.所得的多孔炭电极均表现出优异的循环稳定性.这一工作以BMIMPF_6作为模板和辅助活化剂,为合成生物质基超级电容器用多孔炭提供了一种新方法.     

炭化对沥青基活性炭纤维的结构和超级电容器性能影响

以450℃低温炭化的各向异性中间相沥青基炭纤维为原料,先通过KOH化学活化方法制备出活性炭纤维(ACFs),再对ACFs进行炭化改性,以提高ACFs的导电率,系统地研究了炭化温度对ACFs微观形貌、结晶度、孔结构和超级电容器性能的影响。结果显示:经过1 200℃炭化处理的ACFs(ACFs~(-1)200)电极具有优异的电化学性能,在0.1 A·g~(-1)电流密度下比容量高达204 F·g~(-1),1 000次循环后电容保持率达到97.0%;且电流增至20 A·g~(-1)时依然具有高比容量(149 F·g~(-1)),表明ACFs~(-1)200电极相比于未炭化的ACFs,其导电率、大电流密度下的比容量、循环保持率均显著提高。     

CP@NiAl-LDH复合材料的制备及其超级电容器性能

通过采用简易温和的水热条件制备导电聚合物@镍铝层状双金属氢氧化物复合材料(CP@NiAl-LDH),构建电子/离子的高速传输纳米通道,利用SEM和XRD对复合材料结构形貌进行表征。电化学性能测试结果表明,导电聚合物为复合材料提供一定的赝电容,促进电荷的快速转移,使CP@NiAl-LDH的电容性能得以显著提升。PPy@LDH具有最好的电容性能,在1 A·g~(-1)的电流密度下,其比容量高达3 010.3 F·g~(-1),当电流密度升高到20 A·g~(-1)时,其比电容保持率为73.1%,表现出优异的倍率性能;同时,在10 A·g~(-1)的电流密度下10 000次充放电循环后仍具有88.8%的比容量保持率,具有优异的循环稳定性。这主要归功于NiAl-LDH与导电聚合物之间的协同增强效应。     

介孔碳/石墨烯复合材料的制备及其醌类改性电容性能

首先利用硬模板法制备出介孔碳/石墨烯复合材料,然后向复合材料中引入具有赝电容活性的醌类分子进一步增大材料的电容性能。研究结果表明,负载30%(w/w)叔丁基氢醌的介孔碳/石墨烯复合材料具有最佳的电容性能,在电流密度为0.5 A·g~(-1)时,比电容值为355 F·g~(-1);当电流密度高达30 A·g~(-1)时,其比电容值高达226 F·g~(-1),比电容保持率为64%,表现出良好的速率特性。     

具有高效电化学储能的中空网状笼还原氧化石墨烯（英文）

通过ZnO模板辅助电沉积法制备了中空网状笼还原氧化石墨烯,具有纳米管、多孔结构、网状结构和3D微米中空笼等多层次架构.这样的结构能够同时促进电化学活性物种的传输,提高电极材料的利用率,以及提升超级电容器性能.该类中空网状笼还原氧化石墨烯做超级充电器电极材料时表现出了优良的电化学性能,研究结果显示,在1.0 A·g~(-1)时比电容达到393 F·g~(-1).而且当电流密度从1.0 A·g~(-1)增加到20 A·g~(-1),电容仅衰减了21.2%,10000周循环后比电容损失小于1%,表明具有优异的电容稳定性.     

GR/MoO3柱状复合材料制备及其电容性质

以钼粉和氧化石墨为前驱物,在水热反应釜内,180℃反应12 h,制得了GR/MoO_3柱状复合材料。利用XRD和SEM表征了材料的结构和形貌。在三电极体系中,研究了GR/MoO_3复合材料的电容性质。当电流密度为0.5A·g~(-1)时,GR/MoO_3复合材料的比电容高达440 F·g~(-1),并且表现出良好的循环稳定性,是一种比较有潜力的电容性电极材料。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Microwave-assisted copper-catalyzed stereoselective ring expansion of three-membered heterocycles with α-diazo-β-dicarbonyl compounds

Microwave-assisted copper-catalyzed ring expansions of three-membered heterocycles with α-diazo-β-dicarbonyl compounds were investigated. Thiiranes generated 3-acyl-5,6-dihydro-1,4-oxathiines in the presence of copper sulfate and trans-3-acyl-5,6-dihydro-1,4-oxathiines as stereospecific products for 1,2-disubstituted cis-thiiranes through an intramolecular S_N2 process. Oxiranes gave rise to 2-acyl-5,6-dihydro-1,4-dioxines under the catalysis of copper hexafluoroacetylacetonate and cis-3-acyl-5,6-dihydro-1,4-dioxines as stereospecific products for 1,2-disubstituted cis-oxiranes via an intimate ion-pair mechanism. The current method provides a direct and simple strategy in efficient preparation of 3-acyl-5,6-dihydro-1,4-oxathiines and 2-acyl-5,6-dihydro-1,4-dioxines, important agents in medicinal and agricultural chemistry, from readily available thiiranes and oxiranes, respectively.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.