Existence states of deuterium irradiated into LiAlO2

The existence states of deuterium in LiAlO₂ were analyzed by in situ IR absorption spectroscopy during irradiation with 3 keV at room temperature. Multiple IR absorption peaks that were related to O-D stretching vibrations were observed, mainly at 2650 cm⁻¹ (O-D_α), 2600 cm⁻¹ (O-D_β), and 2500 cm⁻¹ (O-D_γ). The O-D_α was assigned to the surface O-D. The O-D_β and O-D_γ were interpreted as two distinct O-D states for three candidates: O-D of substitutional D⁺ for Li⁺; O-D of substitutional D⁺ for Al³⁺; and O-D of interstitial D⁺. O-D_β was the dominant O-D state for deuterium irradiated into LiAlO₂, and had higher stability than O-D_γ. Heating after ion irradiation led to the desorption of D₂ and an increase in the intensity of O-D_β, which implies that some of the deuterium irradiated into LiAlO₂ exists in non-O-D states, such as D⁻ captured by F centers.     

Swift heavy ion induced modifications of fullerene C70 thin films

Modifications of the C₇₀ molecule (fullerene) under swift heavy ion irradiation are investigated. C₇₀ thin films were irradiated with 120 MeV Au ions at fluences from 1 × 10¹² to 3 × 10¹³ ions/cm². The energetic ion impacts lead to the destruction of the C₇₀ molecule. To investigate the stability of C₇₀ fullerene, the damage cross-section and radius of the damaged cylindrical zones are evaluated by fitting the evanescence of C₇₀ vibration modes recorded by Raman spectroscopy. Conductivity measurements together with Raman and optical absorption studies revealed that an irradiation fluence of 3 × 10¹³ ions/cm² results in complete amorphization of the carbon structure of the fullerene molecules.     

Ion beam induced modifications in electron beam evaporated aluminum oxide thin films

Al₂O₃ thin films find wide applications in optoelectronics, sensors, tribology etc. In the present work, Al₂O₃ films prepared by electron beam evaporation technique are irradiated with 100 MeV swift Si⁷⁺ ions for the fluence in the range 1 × 10¹² to 1 × 10¹³ ions cm⁻² and the structural properties are studied by glancing angle X-ray diffraction. It shows a single diffraction peak at 38.2° which indicates the γ-phase of Al₂O₃. Further, it is observed that as the fluence increases up to 1 × 10¹³ ions cm⁻² the diffraction peak intensity decreases indicating amorphization. Surface morphology studies by atomic force microscopy show mean surface roughness of 34.73 nm and it decreases with increase in ion fluence. A strong photoluminescence (PL) emission with peak at 442 nm along with shoulder at 420 nm is observed when the samples are excited with 326 nm light. The PL emission is found to increase with increase in ion fluence and the results are discussed in detail.     

Structural studies of silicon oxynitride layers formed by low energy ion implantation

Silicon oxynitride (Si_xO_yN_z) layers were synthesized by implanting ¹⁶O₂⁺ and ¹⁴N₂⁺ 30 keV ions in 1:1 ratio with fluences ranging from 5 × 10¹⁶ to 1 × 10¹⁸ ions cm⁻² into single crystal silicon at room temperature. Rapid thermal annealing (RTA) of the samples was carried out at different temperatures in nitrogen ambient for 5 min. The FTIR studies show that the structures of ion-beam synthesized oxynitride layers are strongly dependent on total ion-fluence and annealing temperature. It is found that the structures formed at lower ion fluences (∼1 × 10¹⁷ ions cm⁻²) are homogenous oxygen-rich silicon oxynitride. However, at higher fluence levels (∼1 × 10¹⁸ ions cm⁻²) formation of homogenous nitrogen rich silicon oxynitride is observed due to ion-beam induced surface sputtering effects. The Micro-Raman studies on 1173 K annealed samples show formation of partially amorphous oxygen and nitrogen rich silicon oxynitride structures with crystalline silicon beneath it for lower and higher ion fluences, respectively. The Ellipsometry studies on 1173 K annealed samples show an increase in the thickness of silicon oxynitride layer with increasing ion fluence. The refractive index of the ion-beam synthesized layers is found to be in the range 1.54-1.96.     

Heavy ion beam micromachining on LiNbO3

In this work 3D micromachining of x-cut lithium niobate crystals was performed using the high energy heavy ion microbeam (HIM) at the Tandar Laboratory, Buenos Aires. The samples were machined using ³⁵Cl beams at 70 MeV bombarding energy combined with wet etching with hydrofluoric acid solutions at room temperature. As the ion beam penetrates the sample, it induces lattice damage increasing dramatically the local etching rate of the material. This technique was applied to the fabrication of 3D waveguides with long control electrodes. The resulting structures indicate that well defined contours with nearly vertical sidewalls can be made. The results also show that with fluences of only 5 × 10¹² ions/cm², this technique is suitable for the fabrication of different shapes of LiNbO₃ control-waveguides that can be used in different optical devices and matched with the existing optical fibers.     

Amorphisation of ZnAl2O4 spinel under heavy ion irradiation

ZnAl₂O₄ spinels have been irradiated with several ions (Ne, S, Kr and Xe) at the IRRSUD beamline of the GANIL facility, in order to determine irradiation conditions (stopping power, fluence) for amorphisation. We observed by transmission electron microscopy (TEM) that with Xe ions at 92 MeV, individual ion tracks are still crystalline, whereas an amorphisation starts below a fluence of 5 × 10¹² cm⁻² up to a total amorphisation between 1 × 10¹³ and 1 × 10¹⁴ cm⁻². The coexistence of amorphous and crystalline domains in the same pristine grain is clearly visible in the TEM images. All the crystalline domains remain close to the same orientation as the original grain. According to TEM and X-ray Diffraction (XRD) results, the stopping power threshold for amorphisation is between 9 and 12 keV nm⁻¹.     

Swelling and optical properties of Si3N4 films irradiated in the electronic regime

Silicon nitride layers of 140 nm thickness were deposited on silicon wafers by low pressure chemical vapour deposition (LPCVD) and irradiated at GANIL with Pb ions of 110 MeV up to a maximum fluence of 4 × 10¹³ cm⁻². As shown in a previous work these irradiation conditions, characterized by a predominant electronic slowing-down (S_e = 19.3 keV nm⁻¹), lead to damage creation and formation of etchable tracks in Si₃N₄. In the present study we investigated other radiation-induced effects like out of plane swelling and refractive index decrease. From profilometry, step heights as large as 50 nm were measured for samples irradiated at the highest fluences (>10¹³ cm⁻²). From optical spectroscopy, the minimum reflectivity of the target is shifted towards the high wavelengths at increasing fluences. These results evidence a concomitant decrease of density and refractive index in irradiated Si₃N₄. Additional measurements, performed by ellipsometry, are in full agreement with this interpretation.     

Tuning magnetic properties of Co/Pt thin films using energetic ions

In this paper, we present the changes occurring in Co/Pt bi- and multi-layer thin films modified under wide range of ion energy and species and fluence. We have shown the possibility of achieving controlled tuning of magnetic properties of the Co/Pt thin film system. Monte Carlo simulation results for ion-induced atomic displacements were used to explain the observed effects of ion-irradiation interface mixing across the Co/Pt interfaces. Phase formation has been explained in the light of heat of formation rule. On the other hand, we propose that ion induced point defect clustering governs the changes occurring in the structural and the magnetic properties.     

Effect of 200 MeV Ag ion irradiation on structural and electrical transport properties of Fe3O4 thin films

Thin films of Fe₃O₄ have been deposited on single crystal MgO(1 0 0) and Si(1 0 0) substrates using pulsed laser deposition. Films grown on MgO substrate are epitaxial with c-axis orientation whereas, films on Si substrate are highly 〈1 1 1〉 oriented. Film thicknesses are 150 nm. These films have been irradiated with 200 MeV Ag ions. We study the effect of the irradiation on structural and electrical transport properties of these films. The fluence value of irradiation has been varied in the range of 5 × 10¹⁰ ions/cm² to 1 × 10¹² ions/cm². We compare the irradiation induced modifications on various physical properties between the c-axis oriented epitaxial film and non epitaxial but 〈1 1 1〉 oriented film. The pristine film on Si substrate shows Verwey transition (T_V) close to 125 K, which is higher than generally observed in single crystals (121 K). After the irradiation with the 5 × 10¹⁰ ions/cm² fluence value, T_V shifts to 122 K, closer to the single crystal value. However, with the higher fluence (1 × 10¹² ions/cm²) irradiation, T_V again shifts to 125 K.     

AFM and photoluminescence studies of swift heavy ion induced nanostructured aluminum oxide thin films

E-beam evaporated aluminum oxide films were irradiated with 120 MeV swift Au⁹⁺ ions in order to induced nanostructure formation. Atomic force microscope (AFM) results showed the formation of nanostructures for films irradiated with a fluence of 1 × 10¹³ ions cm⁻². The particle size estimated by section analysis of the irradiated film was in the range 25-30 nm. Glancing angle X-ray diffraction (GAXRD) revealed the amorphous nature of the films. Two strong Photoluminescence (PL) emission bands with peaks at ∼430 nm and ∼645 nm besides a shoulder at ∼540 nm were observed in all irradiated samples. The PL intensity is found to increase with increase of ion fluence.     

Bulk-compositional changes of Ni2Al3 and NiAl3 during ion etching

Bulk-compositional changes of Ni₂Al₃ and NiAl₃ in a Ni-50 wt% Al alloy during ion etching have been investigated by transmission electron microscopy and energy dispersive X-ray spectroscopic analyses. After etching with 7, 5 and 3 keV Ar⁺ ions for 15, 24 and 100 h nickel contents in both Ni₂Al₃ and NiAl₃ exceeded greatly those in the initial compounds and increased with the decrement of the sputtering energy. After 100 h etching with 3 keV Ar⁺ ions the compositions of these two compounds reached a similar value, about Ni_80-83Al_12-15Fe_3-4Cr_1-2 (at%). A synergistic action of preferential sputtering, radiation-induced segregation and radiation-enhanced diffusion enables the altered-layers at the top and bottom of the film extend through the whole film. The bulk-compositional changes are proposed to occur in the unsteady-state sputtering regime of ion etching and caused by an insufficient supply of matter in a thin film.     

Swift heavy ion irradiation induced texturing in NiO thin films

NiO thin films grown on Si(1 0 0) substrate by electron beam evaporation and sintered at 500 and 700 °C were irradiated with 120 MeV Au⁹⁺ ions. The FCC structure of the sintered films was retained up to the highest fluence (3 × 10¹³ ions cm⁻²) of irradiation. In the low fluence (?1 × 10¹³ ions cm⁻²) regime however, the evolution of the XRD pattern with fluence showed a wide variation, critically depending upon their initial microstructure. Though irradiation is known to induce disorder in the structure, we observe improvement in crystallization and texturing at intermediate fluences of irradiation.     

Electron spin resonance investigations on ion beam irradiated single-wall carbon nanotubes

ESR investigations on single-wall carbon nanotubes irradiated with accelerated protons, helium ions, and neon ions are reported. All spectra were accurately simulated assuming that the resonance line is a convolution of up to 4 lines originating from catalyst residues, amorphous carbon, and electrons delocalized over the conducting domains of nanotubes. The faint line observed in irradiated nanotubes at g > 2.25 was assigned to magnetic impurities. However, there are no sufficient data to confirm that this line is connected to radiation-induced magnetism in carbon nanotubes. The generation of paramagnetic defects due to the bombardment of single-wall carbon nanotubes by accelerated ions is reported. These data correlate with previous Raman and thermal investigations on the same single-wall carbon nanotubes and reveals their sensitivity to ionizing radiation. The temperature dependence of ESR spectra in the range 25-250 K was used to identify the components of the ESR spectra.     

Grain boundary influence on displacement cascades in UO2: A molecular dynamics study

The influence of grain boundaries on the primary damage state created by a recoil nucleus in UO₂ matrix is studied here by molecular dynamics simulations. This study is divided in two steps: (1) the study of the structural properties of several symmetrical tilt boundaries for different misorientation angles ranging from 12.7° to 61.9°; and (2) the study of displacement cascades near these grain boundaries. For all the grain boundaries studied, the structure around the interface up to about 2 nm presents a perturbed but stable fluorite lattice. The type of defect at the interface depends directly on the value of the misorientation angles. For the small angles (12.7° and 16.3°) the interface defects correspond to edge dislocations. For higher misorientation angles, a gap of about 0.3 nm exists between the two halves of the bicrystal. This gap is composed of Schottky defects involving numerous vacancies along the interface. About 10 keV displacement cascades were initiated with an uranium projectile close to the interface. In all the cases, numerous point defects are created in the grain boundary core, and the mobility of these defects increases. However, cascade morphologies depend strongly on the grain boundary structure. For grain boundaries with edge dislocations, the evolution of the displacement cascades is similar to those carried out in monocrystals. On the other hand, cascades initiated in grain boundaries with vacancy layer defects present an asymmetry on the number of displaced atoms and the number of point defects created.     

Enhanced susceptibility of CaF2(1 1 1) to adsorption due to ion irradiation

We have investigated morphological changes of freshly cleaved CaF₂(1 1 1) single crystal surfaces before and after ion irradiation. We show that with or without irradiation the surface undergoes serious changes within minutes after the cleavage if the samples are exposed to ambient conditions. This is most likely due to the adsorption of water and could be avoided only if working under clean ultra-high-vacuum conditions. Ion-induced modifications on this surface seem to act as centers for an increased rate of adsorption so that any quantitative numbers obtained by atomic force microscopy in such experiments have to be treated with caution.     

Self-diffusion near symmetrical tilt grain boundaries in UO2 matrix: A molecular dynamics simulation study

Molecular dynamics simulations have been carried out to study the influence of grain boundaries in stoichiometric UO₂ on uranium and oxygen self-diffusions over a large range of temperature varying from 300 K to 2100 K. The study was carried out on two symmetrical tilt grain boundaries, Σ5 and Σ41, which have respectively two different atomic structures. Firstly, the study of the temperature effect on the grain boundary core structure is presented. With the raise of temperature, the grain boundary core grows with an increase of disorder. Secondly, self-diffusion near both grain boundaries is studied. It has been found that grain boundaries accelerate the uranium and oxygen self-diffusion rates over several nanometres from the grain boundary interface. Uranium and oxygen self-diffusion are anisotropic, with a high acceleration along the grain boundary interface. Using the self-Van Hove correlation functions, hopping mechanisms were identified for Σ41 in all directions while for Σ5 hopping mechanism takes place along the grain boundary interface and random diffusion appears in the perpendicular direction of the grain boundary plane.     

Effects of energetic heavy ion irradiation on the structure and magnetic properties of FeRh thin films

Fe-54at.%Rh thin films were irradiated with 10 MeV iodine ions at room temperature. Before and after the irradiations, the changes in magnetic properties and the lattice structure of the samples were studied by means of a SQUID magnetometer and X-ray diffraction. For the low fluence irradiation, the SQUID measurement at 20 K shows that the anti-ferromagnetic region of the thin film is changed into ferromagnetic region by the irradiation. As the film thickness is much smaller than the ion range, we can discuss the relationship between the density of energy deposited by ions and the change in magnetization quantitatively. For the high fluence irradiation, the magnetization of the film is strongly decreased by the irradiation, which can be explained as due to the change in lattice structure from B2 into A1 structure by the irradiation.     

Structural studies of Ge nanocrystals embedded in SiO2 matrix

Germanium nanoparticles embedded in SiO₂ matrix were prepared by atom beam sputtering on a p-type Si substrate. The as-deposited films were annealed at temperatures of 973 and 1073 K under Ar + H₂ atmosphere. The as-deposited and annealed films were characterized by Raman, X-ray diffraction and Fourier transform infrared spectroscopy (FTIR). Rutherford backscattering spectrometry was used to quantify the concentration of Ge in the SiO₂ matrix of the composite thin films. The formation of Ge nanoparticles were observed from the enhanced intensity of the Ge mode in the Raman spectra as a function of annealing, the appearance of Ge(3 1 1) peaks in the X-ray diffraction data and the Ge vibrational mode in the FTIR spectra. We have irradiated the films using 100 MeV Au⁸⁺ ions with a fluence of 1 × 10¹³ ions/cm² and subsequently studied them by Raman and FTIR. The results are compared with the ones obtained by annealing.     

Structural characterization of buried nitride layers formed by nitrogen ion implantation in silicon

The synthesis of buried silicon nitride insulating layers was carried out by SIMNI (separation by implanted nitrogen) process using implantation of 140 keV nitrogen (¹⁴N⁺) ions at fluence of 1.0 × 10¹⁷, 2.5 × 10¹⁷ and 5.0 × 10¹⁷ cm⁻² into 〈1 1 1〉 single crystal silicon substrates held at elevated temperature (410 °C). The structures of ion-beam synthesized buried silicon nitride layers were studied by X-ray diffraction (XRD) technique. The XRD studies reveal the formation of hexagonal silicon nitride (Si₃N₄) structure at all fluences. The concentration of the silicon nitride phase was found to be dependent on the ion fluence. The intensity and full width at half maximum (FWHM) of XRD peak were found to increase with increase in ion fluence. The Raman spectra for samples implanted with different ion fluences show crystalline silicon (c-Si) substrate peak at wavenumber 520 cm⁻¹. The intensity of the silicon peak was found to decrease with increase in ion fluence.     

Effect of swift heavy ion irradiation on structure, optical, and gas sensing properties of SnO2 thin films

Swift heavy ion irradiation has been successfully used to modify the structural, optical, and gas sensing properties of SnO₂ thin films. The SnO₂ thin films prepared by sol-gel process were irradiated with 75 MeV Ni⁺ beam at fluences ranging from 1 × 10¹¹ ion/cm² to 3 × 10¹³ ion/cm². Structural characterization with glancing angle X-ray diffraction shows an enhancement of crystallinity and systematic change of stress in the SnO₂ lattice up to a threshold value of 1 × 10¹³ ions/cm², but decrease in crystallinity at highest fluence of 3 × 10¹³ ions/cm². Microstructure investigation of the irradiated films by transmission electron microscopy supports the XRD observations. Optical properties studied by absorption and PL spectroscopies reveal a red shift of the band gap from 3.75 eV to 3.1 eV, and a broad yellow luminescence, respectively, with increase in ion fluence. Gas response of the irradiated SnO₂ films shows increase of resistance on exposure to ammonia (NH₃), indicating p-type conductivity resulting from ion irradiation.