臭氧氧化结合硫代硫酸钠溶液喷淋同时脱硫脱硝

采用臭氧氧化结合湿法喷淋硫代硫酸钠溶液的方法开展模拟烟气同时脱硫脱硝实验研究。结果表明,采用臭氧氧化结合Na₂S₂O₃-NaOH溶液湿法喷淋可以实现NO_x和SO₂协同脱除:在O₃/NO摩尔比为1.1～1.2时,溶液中Na₂S₂O₃浓度的增加会提高系统的NO_x脱除效率,烟气中SO₂的存在会促进NO_x的脱除,当SO₂浓度为1030 mg·m^-3、2.0%Na₂S₂O₃溶液作为喷淋液时可实现较高的SO₂脱除效率,同时NO_x脱除效率可达70%以上;喷淋液pH在2.5～9范围内变化时提高浆液pH有利于NO_x的脱除,当pH 9时脱硝效率可达75%。180 min连续同时脱硫脱硝实验结果表明,硫代硫酸钠可有效促进NO_x的脱除,并实现SO₂较高的脱除效率,同时可实现系统同时脱硫脱硝连续稳定运行,喷淋吸收后烟气中NO_x的主要转化产物为NO₂^-, 该方法作为一种有效的同时脱硫脱硝技术,具有一定的工业应用推广前景。     

离子液体水溶液吸收模拟烟气中SO2

建立了一套放大脱硫装置, 利用该装置研究了乙醇胺乳酸盐([MEA]L)水溶液在不同条件下吸收SO₂的性能, 确定出了较优的实验条件, 并在该条件下进行吸收-解吸SO₂循环实验。研究结果表明:烟气中SO₂的去除率随[MEA]L中水分的增加而增加;SO₂的去除率随着气液比的减少而增加, 在气液比为420, SO₂浓度为2850～14280 mg·m^-3范围内时, 出口烟气中SO₂浓度均小于285 mg·m^-3, 满足排放标准;烟气中的CO₂对[MEA]L水溶液吸收SO₂没有影响;利用蒸汽对富液进行解吸再生, 解吸后的贫液可以继续使用, 并且仍具有很高的SO₂去除率。     

液相射流吸收耦合气相旋流分离烟气脱硫

在传统的除雾型旋风分离器基础上进行改进,使其同时具备液相射流、气液吸收反应以及气液分离功能,并将这一新型旋风分离器用于烟气脱硫实验。实验中气相为含SO₂烟气,液相为NaOH或Na₂CO₃碱液吸收剂,通过调节吸收剂浓度、烟气含硫浓度、烟气喷射速度、吸收剂喷射速度、吸收剂固含率等参数得到其相应脱硫率的变化。实验研究表明：脱硫率随吸收剂浓度的增加先增加,达到一定浓度后脱硫率几乎不变;脱硫率随SO₂进口浓度的升高而下降;随进口气速的增大,脱硫率也一定程度增大;随液体喷射速度的增加脱硫率先增大,增大到一定程度后脱硫率趋于不变;NaOH作为吸收剂所得最佳脱硫率可达85%,Na₂CO₃作为吸收剂,最佳脱硫率可达77%;当其他参数一定时,加入一定量的CaCO₃固体微粒,可以提高脱硫效率1%~2%。该液相射流吸收耦合气相旋流分离装置不仅脱硫效率高,而且脱硫剂损失少,投资成本与运行维护费用均低于相同处理量的烟气脱硫塔,具有良好的应用前景。     

等速升温流态化下CaO/生物质焦的SO2/NO联合脱除特性

燃煤锅炉污染物超低排放标准对电厂脱硫和脱硝系统提出了更高的要求。CaO作为脱硫剂可以实现循环流化床锅炉烟气中SO₂的高效脱除,焦炭作为还原剂直接还原NO,同时CaO的存在对焦炭还原NO起催化作用,可以实现燃煤烟气中SO₂/NO的联合脱除。为了探究连续温度变化对CaO/生物质焦联合脱硫脱硝性能的影响,在钙循环捕集CO₂技术背景下,研究了等速升温流态化下CaO/生物质焦的SO₂/NO联合脱除特性。探究了烟气中O₂和CO₂对CaO/椰壳焦脱除SO₂/NO的影响。结果表明,O₂通过对椰壳焦表面碳原子的活化作用降低了异相还原NO温度,在300~950℃等速升温过程中CaO/椰壳焦的NO脱除效率逐渐增加,780℃以上能实现100%脱硝。O₂也提高了CaO/椰壳焦的脱硫效率。CO₂与CaO的碳酸化反应以及与椰壳焦的气化反应对同时脱除SO₂/NO有明显抑制作用。O₂和CO₂共同作用下,在500~800℃内CaO/椰壳焦的脱硝效率随温度升高而增加,脱硫效率先降低后升高。NO促进了CaO/椰壳焦脱除SO₂,而SO₂对脱硝有抑制作用。800℃时CaO/椰壳焦同时脱除SO₂和NO的效率分别为97.7%和93.9%。     

CO2, NOx and SO2 emissions from the combustion of coal with high oxygen concentration gases

The emissions of CO₂, NO_x and SO₂ from the combustion of a high-volatile coal with N₂- and CO₂-based, high O₂ concentration (20, 50, 80, 100%) inlet gases were investigated in an electrically heated up-flow-tube furnace at elevated gas temperatures (1123–1573 K). The fuel equivalence ratio, φ, was varied in the range of 0.4–1.6. Results showed that CO₂ concentrations in flue gas were higher than 95% for the processes with O₂ and CO₂-based inlet gases. NO_x emissions increased with φ under fuel-lean conditions, then declined dramatically after φ=0.8, and the peak values increased from about 1000 ppm for the air combustion process and 500 ppm for the O₂(20%)+CO₂(80%) inlet gas process to about 4500 ppm for the oxygen combustion process. When φ>1.4 the emissions decreased to the same level for different O₂ concentration inlet gas processes. On the other hand, NO_x emission indexes decreased monotonically with φ under both fuel-lean and fuel-rich combustion. SO₂ emissions increased with φ under fuel-lean conditions, then declined slightly after φ>1.2. Temperature has a large effect on the NO_x emission. Peak values of the NO_x emission increased by 50–70% for the N₂-based inlet gas processes and by 30–50% for the CO₂-based inlet gas process from 1123 to 1573 K. However, there was only a small effect of temperature on the SO₂ emission.     

Catalytic oxidization of SO2 from incineration flue gas over bimetallic Cu–Ce catalysts supported on pre-oxidized activated carbon

To improve the deep sulfation of alumina support, the inertness material activated carbon was used as an alternative support for copper/cerium catalysts to remove SO₂ from incineration flue gas which contained other air pollutants such as NO_X, CO, CO₂, HCl, carbon particulates, and heavy metal vapor. During the 473–820 K, the AC support showed no retention of SO₂. However, the metal Pb composed in the flue gas exhibited the toxic characterization to M/AC catalysts, which was due to the outer orbitals of d subshell all paired.     

一种典型钒钛系SCR催化剂SO3生成特性研究

选择性催化还原（SCR）技术由于脱硝效率高、选择性好而被广泛应用于烟气氮氧化物排放控制;然而,目前广泛采用的钒钛系SCR脱硝催化剂会使烟气中SO₂氧化成SO₃,烟气中过高的SO₃对电厂安全运行会造成严重影响,也会对环境造成污染。以典型V₂O₅-WO₃/TiO₂催化剂为研究对象,系统研究了SCR脱硝过程中烟气流量、温度、O₂浓度、SO₂浓度等对催化剂表面SO₃生成特性的影响,并进一步对SO₃生成的反应动力学特性进行了分析。研究表明：催化剂表面SO₃生成反应中SO₂的反应级数为0.59,当O₂浓度大于3%时,O₂的反应级数为0,该反应的表观活化能为70.39 kJ/mol;实验条件下,烟气中SO₂浓度增加会使SO₃生成的反应速率提高;O₂浓度对催化剂表面SO₃生成影响并不显著;烟气温度对催化剂表面SO₃生成具有显著影响,高温会促进SO₃的生成。     

不同烟气组分对粉状活性焦吸附汞的影响机理

在模拟燃煤热烟气为热源和介质条件下，以准东褐煤为原料，通过一维沉降炉进行炭化活化（一步法）制备粉状活性焦，考察了活性焦对Hg⁰的吸附能力，探索了SO₂、H₂O、O₂、CO₂、H₂O+O₂、SO₂+O₂及H₂O+SO₂+O₂气氛对活性焦吸附Hg⁰的影响机理。结果表明：一步法获得的活性焦对Hg⁰具有较高的吸附性能。N₂气氛作对比，H₂O、H₂O+O₂、CO₂和SO₂气氛下抑制活性焦对Hg⁰的吸附；O₂、SO₂+O₂和H₂O+SO₂+O₂促进活性焦对Hg⁰的吸附。通过Hg 4f的XPS分析证明了不同气氛组成对活性焦吸附Hg⁰的抑制和促进机理。H₂O覆盖在活性焦活性位上和堵塞孔隙而抑制活性焦对Hg⁰的吸附；SO₂与Hg⁰在活性焦上发生竞争吸附而抑制对Hg⁰的吸附；CO₂ 吸附在活性焦微孔上而抑制对Hg⁰的吸附；O₂气氛下主要形成了HgO, SO₂+O₂气氛下Hg⁰被氧化成HgSO₃，进一步氧化成HgSO₄； H₂O+SO₂+O₂气氛下，Hg⁰被氧化成HgO和HgSO₄。     

乙醇胺对介质阻挡耦合电晕放电同时脱除NO、SO2的影响

采用自行设计的介质阻挡耦合电晕放电等离子体反应装置进行了模拟烟气同时脱硫脱硝的研究,分别考察乙醇胺（HOCH₂CH₂NH₂,MEA）在不同模拟烟气体系中对NO、SO₂脱除的影响,深入探讨了MEA在放电过程中与NO的作用机理。结果表明：在N₂/O₂/SO₂/NO体系中,0.56% MEA的加入可以显著消除O₂对NO脱除的抑制作用;在N₂/CO₂/SO₂/NO体系中,MEA会吸收进入体系中的部分CO₂,以减弱CO₂对NO脱除的抑制;在N₂/O₂/CO₂/H₂O/NO/SO₂体系中,0.56% MEA的加入既可以有效减弱H₂O的影响,也可以使NO的脱除率达到71.28%,继续将MEA的体积分数增大至1.20%时,可将该体系下NO脱除率提高到81.25%;同时,MEA可以在短时间内高效吸收体系内的SO₂,且几乎不受其他气体成分的影响,SO₂脱除率保持在95%左右。     

Simultaneous desulfurization and denitrification of sintering flue gas via composite absorbent

Experiments on simultaneous absorption of SO_2 and NO_X from sintering flue gas via a composite absorbent NaClO_2/NaClO were carried out. The effects of various operating parameters such as NaClO_2 concentration(ms), NaClO concentration(mp), molar ratio of NaClO_2/NaClO(M), solution temperature(TR), initial solution pH, gas flow(Vg) and inlet concentration of SO_2(CS) and NO(CN) on the removal efficiencies of SO_2 and NO were discussed. The optimal experimental conditions were determined to be initial solution pH = 6, TR=55 °C and M = 1.3 under which the average efficiencies of desulfurization and denitrification could reach99.7% and 90.8%, respectively. Moreover, according to the analysis of reaction products, it was found that adding NaClO to NaClO_2 aqueous solution is favorable for the generation of ClO_2 and Cl_2 which have significant effect on desulfurization and denitrification. Finally, engineering experiments were performed and obtained good results demonstrating that this method is practicable and promising.     

Engineering practice and economic analysis of ozone oxidation wet denitrification technology

SO₂ and NO emitted from coal-fired power plants have caused serious air pollution in China. In this study, a test system for NO oxidation using O₃ is established. The basic characteristics of NO oxidation and products forms are studied. A separate test system for the combined removal of SO₂ and NO_x is also established, and the absorption characteristics of NO_x are studied. The characteristics of NO oxidation and NO_x absorption were verified in a 35 t·h^-1 industrial boiler wet combined desulfurization and denitrification project. The operating economy of ozone oxidation wet denitrification technology is analyzed. The results show that O₃ has a high rate and strong selectivity for NO oxidation. When O₃ is insufficient, the primary oxidation product is NO₂. When O₃ is present in excess, NO₂ continues to get oxidized to N₂O₅ or NO₃. The removal efficiency of NO₂ in alkaline absorption system is low (only about 15%). NO_x removal efficiency can be improved by oxidizing NO_x to N₂O₅ or NO₃ by increasing ozone ratio. When the molar ratio of O₃/NO is 1.77, the NO_x removal efficiency reaches 90.3%, while the operating cost of removing NO_x per kilogram is 6.06 USD (NO₂).     

添加剂CH3COONH4对介质阻挡-电晕放电耦合法脱除NO、SO2的影响

采用自行研究设计的介质阻挡-电晕放电等离子体反应装置在模拟烟气中进行NO、SO₂的脱除研究。考察了O₂、CO₂、水蒸气等气体组分对脱除NO、SO₂的影响,并进一步探讨了添加剂CH₃COONH₄对脱除NO、SO₂的影响及作用机理。实验结果表明：O₂、CO₂和水蒸气浓度的增加对NO脱除有抑制作用,而引入CH₃COONH₄后,这些抑制作用会被减弱,使NO的脱除率得到大幅度提升,但这些抑制作用不会完全消除。在引入CH₃COONH₄后,气体组分和输入电流的变化对脱除SO₂的影响不明显,SO₂脱除率可达到94%左右。在N₂/O₂/CO₂/H₂O/NO/SO₂体系中加入0.27%的CH₃COONH₄后,NO初始浓度不变的条件下,SO₂含量较少时,对NO的脱除影响不明显,随着SO₂浓度的增加,NO的脱除率不断下降,增加CH₃COONH₄的添加量可消除SO₂的影响;另一方面,在SO₂初始浓度恒定的条件下,随着NO含量的增加,SO₂的脱除率保持在94%左右。在N₂/O₂/CO₂/H₂O/NO/SO₂体系中加入0.51%的CH₃COONH₄后,输入电流2.5A时,NO的脱除率达到72%。     

Removal of nitric oxide from simulated flue gas using aqueous persulfate with activation of ferrous ethylenediaminetetraacetate in the rotating packed bed

Nitric oxide being a major gas pollutant has attracted much attention and various technologies have been developed to reduce NO emission to preserve the environment. Advanced persulfate oxidation technology is a workable and effective choice for wet flue gas denitrification due to its high efficiency and green advantages. However, NO absorption rate is limited and affected by mass transfer limitation of NO and aqueous persulfate in traditional reactors. In this study, a rotating packed bed (RPB) was employed as a gas–liquid absorption device to elevate the NO removal efficiency (η_NO) by aqueous persulfate ((NH₄)₂S₂O₈) activated by ferrous ethylenediaminetetraacetate (Fe²⁺-EDTA). The experimental results regarding the NO absorption were obtained by investigating the effect of various operating parameters on the removal efficiency of NO in RPB. Increasing the concentration of (NH₄)₂S₂O₈ and liquid–gas ratio could promoted the oxidation and absorption of NO while theη_NO decreased with the increase of the gas flow and NO concentration. In addition, improving the high gravity factor increased the η_NO and the total volumetric mass transfer coefficient (K_Gα) which raise the η_NO up to more than 75% under the investigated system. These observations proved that the RPB can enhance the gas–liquid mass transfer process in NO absorption. The correlation formula between K_Gα and the influencing factors was determined by regression calculation, which is used to guide the industrial scale-up application of the system in NO removal. The presence of O₂ also had a negative effect on the NO removal process and through electron spin resonance spectrometer detection and product analysis, it was revealed that Fe²⁺-EDTA activated (NH₄)₂S₂O₈ to produce •SO₄^–, •OH and •O₂^–, played a leading role in the oxidation of NO, to produce NO₃^– as the final product. The obtained results demonstrated a good applicable potential of RPB/PS/Fe²⁺-EDTA in the removal of NO from flue gases.     

燃煤电厂CO2捕集中烟气预处理系统的优化模拟

在燃煤电厂CO₂捕集中,为了提高其捕集效率,需对进入系统的烟气进行预处理。为进一步提高进入系统烟气的质量,本文用Aspen Plus模拟优化烟气预处理系统,通过研究在预洗塔中组合填料、填料层高度、吸收剂进量和分层进吸收剂对出口烟气中SO₂的含量、脱硫效率以及出口烟气温度的影响,得出最佳的工艺条件。模拟结果表明,加入不同种类组合填料,同种类不同型号组合填料和分层进吸收剂都使烟气脱硫效率增加,出口烟气温度降低;随着填料层高度和吸收剂进量的增加,出口烟气中SO₂的含量和出口烟气温度降低,其中最佳的高度为2~4m,最佳的吸收剂进量为(250~350)×10³kg/h。     

CeO2表面氧化转移FCC烟气中SO2的反应过程

为提高Ce基脱硫助剂对石油加工过程中流化催化裂化（FCC）烟气深度脱硫效果,采用实验与密度泛函理论（DFT）探究了SO₂、O₂在CeO₂表面的反应过程。通过60℃、200℃反应温度下SO₂、O₂与CeO₂的反应,对反应前后CeO₂样品的XRD、IR、XPS谱图比较分析,探索S、Ce的价态变化和相对含量转变规律,从而推测SO₂可能的反应路径。基于密度泛函理论模拟构造了O₂单分子和SO₂、O₂双分子在CeO₂（111）和MgAl₂O₄（111）O空位表面可能产生的吸附构型;利用LST/QST方法搜索SO₂氧化反应过程,计算各步反应能垒。结果表明CeO₂（111）相比MgAl₂O₄（111）具有更好的SO₂催化效果,其中CeO₂在反应中起到了晶格O传递作用,并进一步推断SO₃的脱附过程是整个反应的速率控制步骤。     

水力喷射-空气旋流器用于湿法烟气脱硫及其传质机理

在一种新型高效的气液传质设备--水力喷射-空气旋流器(WSA)中,以Ca(OH)₂料浆为吸收剂进行了模拟烟气湿法脱硫的实验研究。结果表明:脱硫率随进口气速增加而增加;随液体喷射速度增加先增加,增加到一定程度后几乎不变;随烟气中SO₂的进口浓度增加而减小,存在一适宜的Ca(OH)₂浓度和回流比。在气体流量24～72 m³·h^-1、循环液体量0.4～0.8 m³·h^-1、料浆中Ca(OH)₂浓度7500 g·m^-3时,对SO₂浓度为1891～6373 mg·m^-3的烟气进行湿法脱硫,脱硫率达88.9%～97.7%,且WSA的旋流气体和喷射液体在湿法脱硫中具有自清洁能力,未发现内部结垢和喷孔堵塞现象。总体积传质系数K_Ga、有效相界面积a均随进口气速u_G增大而增大,而总传质系数K_G随u_G增加变化较小;当液体喷射速度 u_L≤0.26 m·s^-1时,K_Ga和K_G随u_L增加快速增大,之后增加缓慢,而a随u_L几乎线性增加,K_Ga和K_G随吸收剂中Ca(OH)₂浓度c_L增加有一最大值。结合实验数据拟合得到了相关的经验公式,这些关联式能较好地预测WSA的湿法脱硫传质性能。气体旋流场强度对总体积传质系数K_Ga和有效相界面积a起支配作用,脱硫传质过程同时受气膜和液膜阻力控制,但以液膜控制为主。     

The mechanism of SO2 effect on NO reduction with propene over In2O3/Al2O3 catalyst

An In₂O₃/Al₂O₃ catalyst shows high activity for the selective catalytic reduction of NO with propene in the presence of oxygen. The presence of SO₂ in feed gas suppressed the catalytic activity dramatically at high temperatures; however it was enhanced in the low temperature range of 473–573 K. In TPD and FT-IR studies, the formation of sulfate species on the surface of the catalyst caused an inhibition of NO_X adsorption sites, and the absorbance ability of NO was suppressed by the presence of SO₂, and the amount of ad-NO₃⁻ species decreased obviously. This leads to a decrease of catalytic activity at higher temperatures. However, addition of SO₂ enhanced the formation of carboxylate and formate species, which can explain the promotional effect of SO₂ at low temperature, because active C₃H₆ (partially oxidized C₃H₆) is crucial at low temperature.     

富氧燃烧烟气压缩净化及高浓度CO2制备工艺研究

富氧燃烧技术是目前最有可能大规模推广和商业应用的碳捕集与封存技术之一,其中,烟气压缩净化及CO₂提纯对于整个富氧燃烧系统至关重要。然而,目前研究多聚焦于富氧燃烧后烟气压缩净化的工艺验证,而对烟气压缩纯化各单元运行特性的研究仍不深入,特别是烟气压缩净化过程杂质污染组分的迁移转化、系统运行参数与污染物脱除效率的关联仍不明确。且现有研究对净化后烟气的深度提纯及高浓度CO₂制备的关注也相对较少,直接关系到富氧燃烧系统运行经济性。因此,针对富氧燃烧烟气净化及CO₂提纯需求,系统探究了富氧燃烧烟气压缩纯化过程SO₂、NO_x吸收脱除以及CO₂深度提纯等各子系统的运行特性,其中SO₂与NO_x脱除采用压缩-酸液吸收,CO₂深度提纯采用低温精馏。结果表明:通过烟气净化可实现SO₂脱除效率达100%,NO脱除效率达99%,同时实现纯度为99.99%的食品级液态CO₂制备。烟气净化过程中,气相反应占据主导,提高压力可缩短反应时间;当SO₂吸收塔运行压力超过0.8 MPa时,SO₂脱除效率可达100%;当NO吸收塔运行压力超过3.0 MPa时,NO排放浓度可达超低排放标准。CO₂提纯过程中,提高压力会降低液体CO₂纯度。SO₂吸收塔运行压力为1.6 MPa、NO吸收塔运行压力为3.0 MPa、CO₂提纯塔运行压力为3.8 MPa时,系统整体功耗最低,为0.37 MJ/kg。     

采用响应面法降低湿法氧化脱硫中Na2S2O3生成量

Na₂S₂O₃是湿法脱硫过程外排废液中最主要的副盐,降低Na₂S₂O₃的生成量对绿色生产具有重要意义。首先采用Plackett-Burman实验筛选出影响Na₂S₂O₃生成量的关键因素,即pH、单质硫浓度、温度。在此基础上运用响应曲面法,以Na₂S₂O₃生成量为目标函数,进行三因素三水平的优化设计分析。研究结果表明,pH对Na₂S₂O₃的影响最大,其次是温度和单质硫浓度,因子间交互作用的影响很小。得到最优的操作条件为pH 8.25,单质硫浓度0.47 g/L,温度31.80℃,PDS浓度90 mg/L,氧硫比1.2 mmol/mmol,此时Na₂S₂O₃生成量为1.838 mmol/L。从Na₂S₂O₃反应动力学和多硫离子的平衡反应两方面对各因素的影响规律进行了解释。最后对实际生产过程进行分析,发现实验得出的pH过低,不利于吸收过程的稳定,现有单质硫熔融分离方法不利于降低脱硫液中的单质硫含量,加速了副盐的生成等问题,对此提出了改进意见,并取得了显著效果。     

Na2CO3基吸附剂颗粒制备及其脱碳性能

采用挤压-滚圆法制备Na₂CO₃基CO₂吸附剂微球颗粒,在自行设计的CO₂吸收系统中对制备的样品进行脱碳性能测试。结合相关表征测试,探明不同载体、不同负载量的Na₂CO₃基吸附剂的微观结构、脱碳性能以及机械性能的变化规律和内在原因。研究表明：不同载体的Na₂CO₃基吸附剂颗粒脱碳性能存在明显差异,其中氧化铝负载的吸附剂（Na₂CO₃/Al₂O₃）的脱碳性能最好,可达1.14mmol/g。铝酸钙水泥负载的吸附剂（Na₂CO₃/CA）机械性能较好,但其脱碳性能最差。结合吸附剂脱碳和机械性能的综合考量,Na₂CO₃/Al₂O₃是最为合适的CO₂吸附剂,并进一步研究不同Na₂CO₃负载量的影响。研究发现随着Na₂CO₃负载量的变化,吸附剂的微观结构、脱碳性能以及机械性能都存在明显的差异。虽然60%负载量的Na₂CO₃/Al₂O₃吸附剂颗粒的机械性能和脱碳效果较好,但其成球度较差,影响其实际应用。质量分数40%负载量的Na₂CO₃/Al₂O₃吸附剂颗粒具有良好的脱碳性能、机械性能以及成球度,CO₂脱除量为1.36mmol/g。总体而言,利用挤压-滚圆法制备的Na₂CO₃基吸附剂颗粒具有良好的流动特性、脱碳性能和机械性能,适用于电厂烟气中的CO₂脱除。